RESUMO
Stochastic phase transformations within individual crystalline particles were recorded by integration of second harmonic generation (SHG) imaging with differential scanning calorimetry (DSC). The SHG activity of a crystal is highly sensitive to the specific molecular packing arrangement within a noncentrosymmetric lattice, providing access to information otherwise unavailable by conventional imaging approaches. Consequently, lattice transformations associated with dehydration/desolvation events were readily observed by SHG imaging and directly correlated to the phase transformations detected by the DSC measurements. Following studies of a model system (urea), stochastic differential scanning calorimetry (SDSC) was performed on trehalose dihydrate, which has a more complex phase behavior. From these measurements, SDSC revealed a broad diversity of single-particle thermal trajectories and direct evidence of a "cold phase transformation" process not observable by the DSC measurements alone.
RESUMO
PURPOSE: Spray drying plays an important role in the pharmaceutical industry for product development of sensitive bio-pharmaceutical formulations. Process design, implementation and optimisation require in-depth knowledge of process-product interactions. Here, an integrated approach for the rapid, early-stage spray drying process development of trehalose and glucagon on lab-scale is presented. METHODS: Single droplet drying experiments were used to investigate the particle formation process. Process implementation was supported using in-line process analytical technology within a data acquisition framework recording temperature, humidity, pressure and feed rate. During process implementation, off-line product characterisation provided additional information on key product properties related to residual moisture, solid state structure, particle size/morphology and peptide fibrillation/degradation. RESULTS: A psychrometric process model allowed the identification of feasible operating conditions for spray drying trehalose, achieving high yields of up to 84.67%, and significantly reduced levels of residual moisture and particle agglomeration compared to product obtained during non-optimal drying. The process was further translated to produce powders of glucagon and glucagon-trehalose formulations with yields of >83.24%. Extensive peptide aggregation or degradation was not observed. CONCLUSIONS: The presented data-driven process development concept can be applied to address future isolation problems on lab-scale and facilitate a systematic implementation of spray drying for the manufacturing of sensitive bio-pharmaceutical formulations.
Assuntos
Excipientes/química , Glucagon/isolamento & purificação , Tecnologia Farmacêutica , Trealose/química , Estabilidade de Medicamentos , Liofilização , Pós , Agregados Proteicos , Estabilidade Proteica , Tecnologia Farmacêutica/instrumentaçãoRESUMO
This study aimed to elucidate the mechanisms and kinetics of coating failure for enteric coated beads exposed to high-humidity conditions at different storage temperatures. Enteric coated beads were placed on high-humidity conditions (75 to 98% relative humidity (RH)) in the temperature range of 5 to 40°C. These stability samples of beads were tested for acid dissolution and water activity and also analyzed with SEM, X-ray CT, and DMA. Exposure of enteric coated beads to high humidity led to increased gastric release of drug which eventually failed the dissolution specification. SEM showed visible cracks on the surface of beads exposed to 5°C/high humidity and fusion of enteric beads into agglomerates at 40°C/high humidity. In a non-destructive time elapse study, X-ray CT demonstrated swelling of microcrystalline cellulose cores, crack initiation, and propagation through the API layer within days under 5°C/98% RH storage conditions and ultimately fracture through the enteric coating. DMA data showed a marked reduction in Tg of the enteric coating materials after exposure to humidity. At 5°C/high humidity, the hygroscopic microcrystalline cellulose core absorbed moisture leading to core swelling and consequent fracture through the brittle API and enteric layers. At 40°C (high humidity) which is above the Tg of the enteric polymer, enteric coated beads coalesced into agglomerates due to melt flow of the enteric coating. We believe it is the first report on two distinct failure models of enteric coated dosage forms.
Assuntos
Celulose/química , Excipientes/química , Microesferas , Celulose/metabolismo , Estabilidade de Medicamentos , Excipientes/metabolismo , Umidade , Polímeros , Comprimidos com Revestimento Entérico , Água/química , Água/metabolismoRESUMO
For oral solid dosage forms, disintegration and dissolution properties are closely related to the powders and particles used in their formulation. However, there remains a strong need to characterize the impact of particle structures on tablet compaction and performance. Three-dimensional non-invasive tomographic imaging plays an increasingly essential role in the characterization of drug substances, drug product intermediates, and drug products. It can reveal information hidden at the micro-scale which traditional characterization approaches fail to divulge due to a lack of resolution. In this study, two batches of spray-dried particles (SDP) and two corresponding tablets of an amorphous product, merestinib (LY2801653), were analyzed with 3D X-Ray Microscopy. Artificial intelligence-based image analytics were used to quantify physical properties, which were then correlated with dissolution behavior. The correlation derived from the image-based characterization was validated with conventional laboratory physical property measurements. Quantitative insights obtained from image-analysis including porosity, pore size distribution, surface area and pore connectivity helped to explain the differences in dissolution behavior between the two tablets, with root causes traceable to the microstructure differences in their corresponding SDPs.
Assuntos
Inteligência Artificial , Microscopia Eletrônica de Varredura , Tamanho da Partícula , Pós , Solubilidade , Comprimidos , Raios XRESUMO
A statistical model enables auto-calibration of second harmonic generation (SHG) images for quantifying trace crystallinity within amorphous solid dispersions (ASDs) over a wide dynamic range of crystallinity. In this paper, we demonstrate particle-counting approaches for quantifying trace crystallinity, combined with analytical expressions correcting for particle overlap bias in higher crystallinity regimes to extend the continuous dynamic range of standard particle-counting algorithms through to the signal averaging regime. The reliability of the values recovered by these expressions was demonstrated with simulated data as well as experimental data obtained for an amorphous solid dispersion formulation containing evacetrapib, an Eli Lilly and Company compound. Since particle counting independently recovers the crystalline volume and the SHG intensity, the average SHG intensity per unit volume can be used as an internal calibrant for quantifying crystallinity at higher volume fractions, for which particle counting is no longer applicable.
Assuntos
Anticolesterolemiantes/química , Benzodiazepinas/química , Microscopia de Geração do Segundo Harmônico/métodos , Algoritmos , Calibragem , Cristalização , Espectroscopia de Infravermelho com Transformada de Fourier , Comprimidos , Difração de Raios XRESUMO
Control and optimization of the physical properties of a drug substance (DS) are critical to the development of robust drug product manufacturing processes and performance. A lack of isolatable, for example, crystalline, DS solid forms can present challenges to achieving this control. In this study, an isolation scheme for an amorphous DS was developed and integrated into the synthetic route producing DS with optimized properties. An inert absorbent excipient (Neusilin® US2) was used to isolate the DS via a novel antisolvent scheme as the final step of the route. Isolation was executed at kilogram scale utilizing conventional equipment. The resulting 50 wt% DS:Neusilin complex had improved physical stability and exceptional micromeritic and tableting properties. Improved dissolution was observed and attributed to enhanced dispersion and increased surface area. Characterization data suggest a high degree of penetration of the DS into the Neusilin, with DS occupying 70% of mesopore and 12% of macropore volume. This approach has application in the isolation and particle engineering of difficult to isolate DS without additional unit operation, such as spray drying, and has the potential for a high degree of optimization and control of physical properties over the course of DS development.