Effect of surface depressions on wetting and interactions between hydrophobic pore array surfaces.

The surface structure is known to significantly affect the long-range capillary forces between hydrophobic surfaces in aqueous solutions. It is, however, not clear how small depressions in the surface will affect the interaction. To clarify this, we have used the AFM colloidal probe technique to measure interactions between hydrophobic microstructured pore array surfaces and a hydrophobic colloidal probe. The pore array surfaces were designed to display two different pore spacings, 1.4 and 4.0 µm, each with four different pore depths ranging from 0.2 to 12.0 µm. Water contact angles measured on the pore array surfaces are lower than expected from the Cassie-Baxter and Wenzel models and not affected by the pore depth. This suggests that the position of the three-phase contact line, and not the interactions underneath the droplet, determines the contact angle. Confocal Raman microscopy was used to investigate whether water penetrates into the pores. This is of importance for capillary forces where both the movement of the three-phase contact line and the situation at the solid/liquid interface influence the stability of bridging cavities. By analyzing the shape of the force curves, we distinguish whether the cavity between the probe and the surfaces was formed on a flat part of the surface or in close proximity to a pore. The pore depth and pore spacing were both found to statistically influence the distance at which cavities form as surfaces approach each other and the distance at which cavities rupture during retraction.

High-resolution x-ray imaging using a structured scintillator.

PURPOSE: In this study, the authors introduce a new generation of finely structured scintillators with a very high spatial resolution (a few micrometers) compared to conventional scintillators, yet maintaining a thick absorbing layer for improved detectivity. METHODS: Their concept is based on a 2D array of high aspect ratio pores which are fabricated by ICP etching, with spacings (pitches) of a few micrometers, on silicon and oxidation of the pore walls. The pores were subsequently filled by melting of powdered CsI(Tl), as the scintillating agent. In order to couple the secondary emitted photons of the back of the scintillator array to a CCD device, having a larger pixel size than the pore pitch, an open optical microscope with adjustable magnification was designed and implemented. By imaging a sharp edge, the authors were able to calculate the modulation transfer function (MTF) of this finely structured scintillator. RESULTS: The x-ray images of individually resolved pores suggest that they have been almost uniformly filled, and the MTF measurements show the feasibility of a few microns spatial resolution imaging, as set by the scintillator pore size. Compared to existing techniques utilizing CsI needles as a structured scintillator, their results imply an almost sevenfold improvement in resolution. Finally, high resolution images, taken by their detector, are presented. CONCLUSIONS: The presented work successfully shows the functionality of their detector concept for high resolution imaging and further fabrication developments are most likely to result in higher quantum efficiencies.

Hydrophobic pore array surfaces: wetting and interaction forces in water/ethanol mixtures.

Interactions between and wetting behavior of structured hydrophobic surfaces using different concentrations of water/ethanol mixtures have been investigated. Silica surfaces consisting of pore arrays with different pore spacings and pore depths were made hydrophobic by silanization. Their static and dynamic contact angles were found to be independent of the pore depth while fewer pores on the surface, i.e. a closer resemblance to a flat surface, gave a lower contact angle. As expected, a higher amount of ethanol facilitated wetting on all the surfaces tested. Confocal Raman microscopy measurements proved both water and ethanol to penetrate into the pores. AFM colloidal probe force measurements clearly showed that formation of air cavitation was hindered between the hydrophobic surfaces in presence of ethanol, and an increase in ethanol concentration was followed by a smaller jump-in distance and a weaker adhesion force. On separation, an immediate jump-out of contact occurred. The measured forces were interpreted as being due to capillary condensation of ethanol between the surfaces giving rise to very unstable cavities immediately rupturing on surface separation.