Development of Gelatin Methacryloyl/Sodium Alginate Interpenetrating Polymer Network Hydrogels for Bone Regeneration by Activating the Wnt/ß-Catenin Signaling Pathway via Lithium Release.

Hydrogels have gained significant attention as biomaterials due to their remarkable properties resembling those of the extracellular matrix (ECM). In the present investigation, we successfully synthesized interpenetrating polymer network (IPN) hydrogels using gelatin methacryloyl (GelMA) and sodium alginate (SA), incorporating various concentrations of lithium chloride (LiCl; 0, 5, and 10 mM), aiming to develop a hydrogel scaffold for bone regeneration. Notably, the compressive modulus of the IPN hydrogels remained largely unaffected upon the inclusion of LiCl. However, the hydrogel with the high concentration of LiCl exhibited reduced fragmentation after compression testing. Intriguingly, we observed a significant improvement in cellular biocompatibility, primarily attributed to activation of the Wnt/ß-catenin signaling pathway induced by LiCl. Subsequently, we evaluated the efficacy of the newly developed IPN-Li hydrogels in a rat cranial defect model and found that they substantially enhanced bone regeneration. Nevertheless, it is important to note that the introduction of high concentrations of LiCl did not significantly promote osteogenesis. This outcome can be attributed to the excessive release of Li+ ions into the extracellular matrix, hindering the desired effect. Overall, the IPN-Li hydrogel developed in this study holds great promise as a biodegradable material for bone regeneration applications.

Prevalence, Characterization, and Antimicrobial Susceptibility of Listeria monocytogenes from Raw Beef and Slaughterhouse Environments in Korea.

The prevalence of Listeria monocytogenes in raw beef and in slaughterhouse environments was investigated from April 2019 to February 2020. Three hundred raw beef samples were purchased from 50 retailers and 10 restaurants (5 samples per source). One hundred and thirty-four samples from slaughterhouse environments were collected by swabbing (10 × 10 cm) the surfaces, gloves, splitting saw, and drains. L. monocytogenes was detected and identified according to the method described in ISO 11290-1, and confirmed by 16S rRNA sequencing. L. monocytogenes was detected in raw beef (2/300, 0.7%), gloves used in carcass splitting (6/21, 28.6%), the splitting saw (1/18, 5.6%), and the drain zone (1/15, 6.7%). All isolates were serotype 1/2a or 1/2c, based on screening using multiplex PCR-based serogrouping assay and serotyping kit for O-H antigens. Pulsed-field gel electrophoresis (PFGE) following ApaI digestion of eight PFGE pulsotypes and four PFGE groups were identified. Biofilm formation analysis using Crystal Violet staining revealed the highest biofilm formation in strain LM-16, followed by D190613. Although L. monocytogenes isolates were susceptible to most antimicrobials, some resistance to penicillin (8/15, 53.3%) and tetracycline (2/15, 13.3%) was observed. Through PFGE, G190426, G190829, and G200210 isolated from the same location in this study were genetically homologous similar to the LM-16 strain, previously isolated from beef carcass in 2006. These results suggest that LM-16 has been continuously present in biofilms in the slaughterhouse environments since 2006. Our study indicates that L. monocytogenes contamination in raw beef could consistently occur during beef processing in slaughterhouse environments through contact with gloves, splitting saws, and drains.

Prevalence, toxin-typing, and antimicrobial susceptibility of Clostridium perfringens from retail meats in Seoul, Korea.

Clostridium perfringens is a ubiquitous, Gram-positive, spore-forming bacterium. It can contaminate many types of retail meat products and cause food poisoning by producing enterotoxins in the small intestines of humans and domestic animals. We investigated the prevalence, toxin-encoding gene profile, and antimicrobial resistance of C. perfringens in beef, chicken, and pork meat purchased from retail markets in Seoul, Korea. C. perfringens was detected according to the International Organization for Standardization 7937, with some modifications, and confirmed using the Vitek 2 system. In total, 38 C. perfringens strains were isolated from 200 meat samples (38/200, 19%; thirty-three from chicken, and five from beef). Among the six toxins evaluated, including alpha, beta, epsilon, iota, enterotoxin (encoded in the cpe gene), and netB, only the cpa gene was detected in all isolates by polymerase chain reaction (PCR) amplification. The antimicrobial resistance of the isolates was evaluated using the agar dilution method and resistance to ampicillin (12/38, 31.6%), tetracycline (38/38, 100%), chloramphenicol (26/38, 68.4%), metronidazole (13/38, 34.2%), and imipenem (27/38, 71%) was observed. Interestingly, 30 of the 38 isolates (78.9%) were multiple-drug resistant, showing resistance to more than three different antimicrobial classes.

Evaluation of fracture strength for single crowns made of the different types of lithium disilicate glass-ceramics.

Lithium disilicate glass-ceramics with high mechanical strength are being widely used as ingots for heat-pressing technique and blocks for CAD/CAM processing in clinical dentistry as aesthetic prosthetic materials. The purpose of this study was to evaluate the fracture strength of single crowns made of the different types of lithium disilicate glass-ceramics. Single crowns for mandibular second premolar with thickness of 1.5 mm were manufactured. IPS e.max Press and Amber Press crowns were produced by heat-pressing, and IPS e.max CAD and Rosetta SM crowns was produced by milling. Amber Lisi-POZ crown was produced by heat-pressing on the zirconia frame. Fracture strength test was performed at 10 degrees of inclination toward the load after bonding crown on metal abutment using dual-curing resin cement. Statistical analysis of fracture strength was conducted through Weibull statistics (n = 15 per group). The mean fracture strength (2087.4 N) of Amber Lisi-POZ group produced by heat-pressing on the zirconia frame was significantly higher than that (1479.8 N) of Rosetta SM group produced by milling. Weibull coefficients for IPS e.max CAD and Rosetta SM groups were, respectively, 14.44 and 9.39, and those for IPS e.max Press, Amber Press, and Amber Lisi-POZ groups produced by heat-pressing were in the range between 4.72 and 5.16. In conclusion, the fracture strength of Amber Lisi-POZ crown with zirconia framework was the highest, and the buccal cusps fractured from the central groove of the all crowns. Weibull modulus of crowns produced by milling was higher than those of crowns produced by heat-pressing.

Comparative evaluation of the mechanical properties of CAD/CAM dental blocks.

This study compares the mechanical properties of commercially available CAD/CAM (Computer-Aided Design/Computer-Aided Manufacturing) millable dental blocks including Vita Enamic, Lava Ultimate, and MAZIC Duro. All the discs were cut in dimension of 1.2 mm in thickness and 12 mm in diameter, ground up to #1200 Sic papers and polished. The biaxial flexure strength of the ceramic discs was measured after thermocycling treatment and the broken surfaces were observed using scanning electron microscopy (SEM). The discs were brushed using a toothbrush testing machine under a 150 g load. Surface roughness and morphology were determined after toothbrushing cycles. Finally, the friction and wear behavior of the materials against an opposing tooth were studied using a reciprocating pin-on-plate test configuration. The vertical loss of dental cusp was measured, and the surface image was examined using field emission scanning electron microscopy (FE-SEM). The biaxial flexural strength data were subjected to Weibull analysis. To compare the significance between the groups, all data were analyzed by one-way analysis (ANOVA). The biaxial flexural strength of the Lava Ultimate and MAZIC Duro materials is significantly higher than that of Vita Enamic. In addition, Lava Ultimate and MAZIC Duro exhibited significantly smoother surfaces than that of Vita Enamic after toothbrushing. Lava Ultimate and MAZIC Duro also showed less wear to the opposing tooth than that of Vita Enamic. In addition, Lava Ultimate possesses more suitable mechanical properties than the Vita Enamic and Mazic Duro for use in oral clinical prosthesis.

Gas formation and biological effects of biodegradable magnesium in a preclinical and clinical observation.

Magnesium alloys are biodegradable metals receiving increasing attention, but the clinical applications of these materials are delayed by concerns over the rapid corrosion rate and gas formation. Unlike corrosion, which weakens mechanical properties, the gas formation issue has received little attention. Therefore, we evaluated the gas formation and biological effects for Mg implants through preclinical (immersed in Earle's balanced salt solution and in vivo) and clinical studies. The immersion test examined the gas volume and composition. The in vivo study also examined gas volume and histological analysis. The clinical study examined the gas volume and safety after Mg screw metatarsal fixation. Gas was mainly composed of H2, CO and CO2. Maximum volumes of gas formed after 5 days for in vivo and 7 days in clinical study. Within the clinical examination, two superficial wound complications healed with local wound care. Osteolytic lesions in the surrounding metaphysis of the Mg screw insertion developed in all cases and union occurred at 3 months. Mg implants released gas with variable volumes and composition (H2, CO, and CO2), with no long-term toxic effects on the surrounding tissue. The implants enabled bone healing, although complications of wound breakdown and osteolytic lesions developed.

Polycaprolactone-MXene coating for controlling initial biodegradation of magnesium implant via near-infrared light.

The mechanical strength of magnesium implants undergoes a rapid decline after implantation due to bioabsorption, which can lead to the risk of rupture. To ensure sustained mechanical strength and initiate bioabsorption selectively upon specific external stimuli until the bone regains sufficient support, we developed a biosafe near-infrared light (NIR)-sensitive polymer coating using polycaprolactone (PCL) and Ti3C2 (MXenes). The synthetic MXene powders were characterized using SEM, EDS, and XRD, and the amount of MXenes had a proliferation-promoting effect on MC3T3-E1, as observed through cell assays. The PCL-MXene coating was successfully prepared on the magnesium surface using the casting coating method, and it can protect the magnesium surface for up to 28 days by decreasing the corrosion ratio. However, the coating can be easily degraded after exposure to NIR light for 20 minutes to expose the magnesium substrate, especially in a liquid environment. Meanwhile, the magnesium implant with the PCL-MXene coating has no cytotoxicity toward MC3T3-E1. These findings can provide a new solution for the development of controlled degradation implants.

Femoral artery occlusion induced vasculopathy following herpes zoster: a case report.

BACKGROUND: Reactivation of the varicella zoster virus (VZV) results in herpes zoster (HZ), which is a painful unilateral rash with a typical dermatomal distribution. HZ may be followed by postherpetic neuralgia (PHN), vasculopathy, myelopathy, retinal necrosis, and cerebellitis. Vasculopathy can cause ischemic stroke, aneurysms, arterial dissection, transient ischemic attack, and rarely, peripheral arterial disease (PAD). The possible mechanism is that the VZV travels to the arteries through the sensory ganglia, leading to inflammation and pathological vascular remodeling, which result in vasculopathy. CASE DESCRIPTION: Here, we describe a rare case of femoral artery occlusion induced vasculopathy 5 years after HZ. A 65-year-old woman visited our pain clinic with persistent pain following HZ that occurred 3 months earlier. She had several rash scars on the right thigh along with a continuous throbbing, shooting, and sharp pain. The patient was diagnosed with PHN and prescribed with medications that relieved the leg pain. The symptoms remained stationary for almost 5 years. She presented again with complaints of a paroxysmal tingling sensation in the right thigh and claudication due to increased pain, which had begun 6 months prior. She reported leg pain after walking for 10 minutes. Lumbar spine magnetic resonance imaging (MRI) revealed foraminal stenosis at the level of right L2, with no abnormality below L2. Subsequently, the patient was evaluated for vascular diseases. Lower extremity ultrasonography and computed tomography (CT) angiography revealed stenosis and thrombotic occlusions in the right superficial femoral and tibial arteries as well as the left middle femoral and tibial arteries. Surgical revascularization via percutaneous angioplasty was performed bilaterally. The leg pain was relieved after the procedure and the claudication improved. CONCLUSIONS: Peripheral artery occlusion is a rare phenomenon following HZ. In cases involving changes in HZ symptoms, further evaluation is required for potential vasculopathy.

Surface modification of a biodegradable magnesium alloy with phosphorylcholine (PC) and sulfobetaine (SB) functional macromolecules for reduced thrombogenicity and acute corrosion resistance.

Siloxane functionalized phosphorylcholine (PC) or sulfobetaine (SB) macromolecules (PCSSi or SBSSi) were synthesized to act as surface modifying agents for degradable metallic surfaces to improve acute blood compatibility and slow initial corrosion rates. The macromolecules were synthesized using a thiol-ene radical photopolymerization technique and then utilized to modify magnesium (Mg) alloy (AZ31) surfaces via an anhydrous phase deposition of the silane functional groups. X-ray photoelectron spectroscopy surface analysis results indicated successful surface modification based on increased nitrogen and phosphorus or sulfur composition on the modified surfaces relative to unmodified AZ31. In vitro acute thrombogenicity assessment after ovine blood contact with the PCSSi and SBSSi modified surfaces showed a significant decrease in platelet deposition and bulk phase platelet activation compared with the control alloy surfaces. Potentiodynamic polarization and electrochemical impedance spectroscopy data obtained from electrochemical corrosion testing demonstrated increased corrosion resistance for PCSSi- and SBSSi-modified AZ31 versus unmodified surfaces. The developed coating technique using PCSSi or SBSSi showed promise in acutely reducing both the corrosion and thrombotic processes, which would be attractive for application to blood contacting devices, such as vascular stents, made from degradable Mg alloys.

Facilitated osteogenesis of magnesium implant by coating of strontium incorporated calcium phosphate.

This study investigated the corrosion resistance and biocompatibility of magnesium coated with strontium-doped calcium phosphate (Sr-CaP) for dental and orthopedic applications. Sr-CaP was coated on biodegradable magnesium using a chemical dipping method. Magnesium coated with Sr-CaP exhibited better corrosion resistance than pure magnesium. Sr-CaP-coated magnesium showed excellent cell proliferation and differentiation. Additionally, new bone formation was confirmed in vivo. Therefore, Sr-CaP-coated magnesium with reduced degradation and improved biocompatibility can be used for orthopedic and dental implant applications.

A Combined In Vitro and In Vivo Assessment of the Safety of the Yeast Strains Kluyveromyces marxianus A4 and A5 Isolated from Korean Kefir.

Kefir is a traditional fermented milk containing beneficial bacteria and yeasts. Despite Kluyveromyces marxianus, isolated from kefir, gaining increasing attention as a potential probiotic yeast owing to its biological function, Saccharomyces boulardii is the only species considered as a probiotic yeast. We evaluated the safety of K. marxianus strains A4 and A5, isolated from Korean kefir, in comparison with that of S. boulardii. Virulence attributes were preliminarily assessed in vitro including their ability of gelatin hydrolysis, pseudohyphae formation, and hemolysis. To evaluate in vivo safety, the strains were challenged in a healthy animal model, four-week-old female BALB/c mice. Mice were orally administered 0.2 mL of 0.9% sterilized saline (NC_S; n = 6), S. boulardii ATCC MYA-796 (high concentration, S.b_H; low concentration, S.b_L; n = 6 for each), K. marxianus A4 (high concentration, A4_H; low concentration, A4_L; n = 6 for each), or K. marxianus A5 (high concentration, A5_H; low concentration, A5_L; n = 6 for each) for 2 weeks. At study end, body weight, spleen and liver weights, and blood parameters were assessed. K. marxianus A4 and A5 were tested negative for gelatinase and hemolysis. Overall, hematological, plasma biochemical, and cytokine (interleukin-1ß and tumor necrosis factor-α) parameters were comparable between the experimental and negative control (NC) groups. Notably, the interleukin-6 level of the A5_H group was significantly lower than that of the NC group (p < 0.05), suggesting anti-inflammatory potential of K. marxianus A5.

Evaluation of osseointegration of Ti-6Al-4V alloy orthodontic mini-screws with ibandronate-loaded TiO2 nanotube layer.

Recently, the use of orthodontic mini-screws as an anchorage for orthodontic treatment is increasing, and the degree of osseointegration of the mini-screws affects the performance of orthodontic treatment. This study aimed to evaluate the biocompatibility and osseointegration of Titanium 6Aluminum 4Vanadium (Ti-6Al-4V) alloy orthodontic mini-screws with an ibandronate-loaded TiO2 nanotube (TNT) layer. The TNT layer was formed on the surface of the Ti-6Al-4V alloy orthodontic mini-screws and loaded with ibandronate. The TNT formed by anodic oxidation formed a completely self-organized and compact structure and was stably released for 7 days after loading with ibandronate. Mini-screws loaded with ibandronate were implanted into both tibias of rats, confirming rapid initial bone regeneration. We demonstrate that the release of stable ibandronate from the TNT layer of Ti-6Al-4V alloy orthodontic mini-screws can effectively improve biocompatibility and osseointegration.

Gut microbiota modulation via short-term administration of potential probiotic kefir yeast Kluyveromyces marxianus A4 and A5 in BALB/c mice.

Kefir yeast, Kluyveromyces marxianus, has been evaluated for its potential probiotic properties-survivability, non-pathogenicity, and antioxidant and anti-microbial activities. However, host gut microbiota modulation of kefir yeasts remains unclear. Here, we compared kefir yeast strains K. marxianus A4 (Km A4) and K. marxianus A5 (Km A5) with Saccharomyces boulardii ATCC MYA-796 (Sb MYA-796) by investigating their adherence to colorectal adenocarcinoma (Caco-2) cells and gut microbiota modulation in BALB/c mice. The kefir yeast strains exhibited higher intestinal cell adhesion than Sb MYA-796 (p < 0.05). Bacteroidetes, Bacteroidales, and Bacteroides were more abundant in the 1 × 108 CFU/mL of Km A4 treatment group than in the control group (p < 0.05). Moreover, 1 × 108 CFU/mL of Km A5 increased Corynebacteriales and Corynebacterium compared to the 1 × 108 CFU/mL of Km A4 treatment group (p < 0.01). The results showed that Km A4 and Km A5 had good Caco-2 cell adhesion ability and modulated gut microbiota upon short-term administration in healthy mice. Supplementary Information: The online version contains supplementary material available at 10.1007/s10068-023-01268-3.

Biocompatibility and Antibacterial Effect of Ginger Fraction Loaded PLGA Microspheres Fabricated by Coaxial Electrospray.

Various poly(lactic-co-glycolic acid) (PLGA) microspheres loaded with the ginger fraction were fabricated by controlling the electrospray parameters and their biocompatibility and antibacterial activity were identified in this study. The morphology of the microspheres was observed using scanning electron microscopy. The core-shell structures of the microparticles and the presence of ginger fraction in the microspheres were confirmed by fluorescence analysis using a confocal laser scanning microscopy system. In addition, the biocompatibility and antibacterial activity of PLGA microspheres loaded with ginger fraction were evaluated through a cytotoxicity test using osteoblast MC3T3-E1 cells and an antibacterial test using Streptococcus mutans and Streptococcus sanguinis, respectively. The optimum PLGA microspheres loaded with ginger fraction were fabricated under electrospray operational conditions with 3% PLGA concentration in solution, an applied voltage of 15.5 kV, a flow rate of 15 µL/min in the shell nozzle, and 3 µL/min in the core nozzle. The effectual antibacterial effect and enhanced biocompatibility were identified when a 3% ginger fraction in PLGA microspheres was loaded.

Enhancement of Biofunctionalization by Loading Manuka Oil on TiO2 Nanotubes.

Metallic implants (mesh) for guided bone regeneration can result in foreign body reactions with surrounding tissues, infection, and inflammatory reactions caused by micro-organisms in the oral cavity after implantation. This study aimed to reduce the possibility of surgical failure caused by microbial infection by loading antibacterial manuka oil in a biocompatible nanostructure surface on Ti and to induce stable bone regeneration in the bone defect. The manuka oil from New Zealand consisted of a rich ß-triketone chemotype, leptospermone, which showed strong inhibitory effects against several bacteria, even at very low oil concentrations. The TiO2 nanotubular layer formed by anodization effectively enhanced the surface hydrophilicity, bioactivity, and fast initial bone regeneration. A concentration of manuka oil in the range of 0.02% to less than 1% can have a synergistic effect on antibacterial activity and excellent biocompatibility. A manuka oil coating (especially with a concentration of 0.5%) on the TiO2 nanotube layer can be expected not only to prevent stenosis of the connective tissue around the mesh and inflammation by microbial infection but also to be effective in stable and rapid bone regeneration.

Antibacterial Activity and Biocompatibility with the Concentration of Ginger Fraction in Biodegradable Gelatin Methacryloyl (GelMA) Hydrogel Coating for Medical Implants.

The gingerols and shogaols derived from ginger have excellent antibacterial properties against oral bacteria. However, some researchers have noted their dose-dependent potential toxicity. The aim of this study was to enhance the biofunctionality and biocompatibility of the application of ginger to dental titanium screws. To increase the amount of coating of the n-hexane-fractionated ginger on the titanium surface and to control its release, ginger was loaded in different concentrations in a photo-crosslinkable GelMA hydrogel. To improve coating stability of the ginger hydrogel (GH), the wettability of the surface was modified by pre-calcification (TNC), then GH was applied on the surface. As a result, the ginger fraction, with a high content of phenolic compounds, was effective in the inhibition of the growth of S. mutans and P. gingivalis. The GH slowly released the main compounds of ginger and showed excellent antibacterial effects with the concentration. Although bone regeneration was slightly reduced with the ginger-loading concentration due to the increased contents of polyphenolic compounds, it was strongly supplemented through the promotion of osteosis formation by the hydrogel and TNC coating. Finally, we proved the biosafety and superior biofunctionalities the GH-TNC coating on a Ti implant. However, it is recommended to use an appropriate concentration, because an excessive concentration of ginger may affect the improved biocompatibility in clinical applications.

Prevalence and Virulence Characteristics of Enterococcus faecalis and Enterococcus faecium in Bovine Mastitis Milk Compared to Bovine Normal Raw Milk in South Korea.

Enterococcus spp. are pathogens that cause environmental mastitis and are difficult to eliminate owing to their resistance to antibiotics. To compare the virulence characteristics of isolates from bovine mastitis milk (BMM) and bovine normal raw milk (NRM), we isolated Enterococcus spp. from 39 dairy farms in South Korea from 2015−2020. A total of 122 Enterococcus spp. were identified, with Enterococcus faecalis (73.8%) accounting for the majority, followed by Enterococcus faecium (26.2%). E. faecalis isolated from BMM harbored gelE, asa1, esp, and cylA genes with a prevalence of 85.7, 71.4, 54.3, and 30.0%, respectively. These genes were significantly more abundant in BMM than in NRM, except for asa1 (p < 0.0001). Interestingly, strong biofilm and gelatinase formation was predominately observed for BMM isolates and this was significantly correlated to the presence of esp and gelE genes (p < 0.05). BMM isolates demonstrated higher resistance to tetracycline (59.3%), followed by chloramphenicol (21.0%), rifampicin (18.5%), doxycycline (4.9%), ciprofloxacin (1.2%), and nitrofurantoin (1.2%), than those from NRM. E. faecalis harboring esp, gelE, and cylA may be causative agents for bovine mastitis and act as a reservoir for the transmission of virulence factors to humans.

Improvement of osseointegration of Ti-6Al-4V ELI alloy orthodontic mini-screws through anodization, cyclic pre-calcification, and heat treatments.

BACKGROUND: Mini-screws are widely used as temporary anchorages in orthodontic treatment, but have the disadvantage of showing a high failure rate of about 10%. Therefore, orthodontic mini-screws should have high biocompatibility and retention. Previous studies have demonstrated that the retention of mini-screws can be improved by imparting bioactivity to the surface. The method for imparting bioactivity proposed in this paper is to sequentially perform anodization, periodic pre-calcification, and heat treatments with a Ti-6Al-4V ELI alloy mini-screw. MATERIALS AND METHODS: A TiO2 nanotube-structured layer was formed on the surface of the Ti-6Al-4V ELI alloy mini-screw through anodization in which a voltage of 20 V was applied to a glycerol solution containing 20 wt% H2O and 1.4 wt% NH4F for 60 min. Fine granular calcium phosphate precipitates of HA and octacalcium phosphate were generated as clusters on the surface through the cyclic pre-calcification and heat treatments. The cyclic pre-calcification treatment is a process of immersion in a 0.05 M NaH2PO4 solution and a saturated Ca(OH)2 solution at 90 °C for 1 min each. RESULTS: It was confirmed that the densely structured protrusions were precipitated, and Ca and P concentrations, which bind and concentrate endogenous bone morphogenetic proteins, increased on the surface after simulated body fluid (SBF) immersion test. In addition, the removal torque of the mini-screw fixed into rabbit tibias for 4 weeks was measured to be 8.70 ± 2.60 N cm. CONCLUSIONS: A noteworthy point in this paper is that the Ca and P concentrations, which provide a scaffold suitable for endogenous bone formation, further increased over time after SBF immersion of the APH group specimens. The other point is that our mini-screws have a significantly higher removal torque compared to untreated mini-screws. These results represent that the mini-screw proposed in this paper can be used as a mini-screw for orthodontics.

Enhancement of Bone Regeneration on Calcium-Phosphate-Coated Magnesium Mesh: Using the Rat Calvarial Model.

Metallic biodegradable magnesium (Mg) is a promising material in the biomedical field owing to its excellent biocompatibility, bioabsorbability, and biomechanical characteristics. Calcium phosphates (CaPs) were coated on the surface of pure Mg through a simple alkali-hydrothermal treatment. The surface properties of CaP coatings formed on Mg were identified through wettability, direct cell seeding, and release tests since the surface properties of biomaterials can affect the reaction of the host tissue. The effect of CaP-coated Mg mesh on guided bone regeneration in rat calvaria with the critical-size defect was also evaluated in vivo using several comprehensive analyses in comparison with untreated Mg mesh. Following the application of protective CaP coating, the surface energy of Mg improved with higher hydrophilicity and cell affinity. At the same time, the CaP coating endowed Mg with higher Ca affinity and lower degradation. The Mg mesh with CaP coating had higher osteointegration and bone affinity than pristine Mg mesh.

Evaluation of Corrosion Behavior and In Vitro of Strontium-Doped Calcium Phosphate Coating on Magnesium.

This study investigated the biocompatibility of strontium-doped calcium phosphate (Sr-CaP) coatings on pure magnesium (Mg) surfaces for bone applications. Sr-CaP coated specimens were obtained by chemical immersion method on biodegradable magnesium. In this study, Sr-CaP coated magnesium was obtained by immersing pure magnesium in a solution containing Sr-CaP at 80 °C for 3 h. The corrosion resistance and biocompatibility of magnesium according to the content of Sr-CaP coated on the magnesium surface were evaluated. As a result, the corrosion resistance of Sr-CaP coated magnesium was improved compared to pure magnesium. In addition, it was confirmed that the biocompatibility of the group containing Sr was increased. Thus, the Ca-SrP coating with a reduced degradation and improved biocompatibility could be used in Mg-based orthopedic implant applications.