Influence of the photothermal effect of a gold nanorod cluster on biofilm disinfection.

We evaluate a method for biofilm disinfection by raising biofilm temperature using the photothermal effect of a gold nanorod cluster. Gold nanorods (GNRs) are capable of generating enough heat to lyse bacteria by heating biofilm via laser irradiation. To test this, GNRs are synthesized using wet chemistry and a single GNR cluster is fabricated using photo-lithography technique. The GNR cluster is directly applied to the biofilm and its effects on bacteria are measured before and after laser irradiation. The photothermal effect of GNRs on the biofilm structure results in a considerable reduction of cell viability and biofilm thickness. Several quantitative measurements of bacterial mortality and biofilm destruction show an increase in efficacy with increasing durations of laser irradiation. Scanning electron microscopy images of the irradiated bacteria show obvious morphological damage such as rupture or collapse of the bacterial cell membrane in the biofilm. These results indicate that GNRs are useful and a potential material for use in photothermal treatments, particularly biofilm disinfection.

Electrical property measurements of metallized flagella-templated silica nanotube networks.

We present an improvement in the electrical properties of silica nanotubes by coating metal nanoparticles on their surfaces. The silica nanotubes are formed from bacterial flagella bio-templates having a tubular structure. Successive depositions of metal nanoparticles on the silica nanotubes are performed through easily functionalized silica surfaces. The results show uniform metal nanoparticle sizes and a high surface area coverage. By incorporating gold, palladium and iron oxide nanoparticles, the metallized silica nanotubes gain electrical properties with the potential to create unique nanoelectronic materials. In this study, the metallized silica nanotubes with network structures are aligned and their electrical behaviors are investigated in both dry and wet conditions. The metallized silica nanotubes are found to be electrically conductive along the network structures. The current-voltage characteristics show remarkably improved electrical conductivities depending on the type of metal nanoparticle loading and nanotube network concentration.

Fabrication of tunable silica-mineralized nanotubes using flagella as bio-templates.

Bacterial flagella are particularly attractive bio-templates for nanotubes due to their tubular structures and small inner and outer diameters. In this work, flagella isolated from Salmonella typhimurium were used as templates for silica-mineralized nanotubes. The process involved pretreatment of flagella with aminopropyltriethoxysilane (APTES), followed by the addition of tetraethoxysilane (TEOS). By controlling the concentration of TEOS and the reaction time, we developed a simple and precise method for creating silica-mineralized flagella nanotubes (SMFNs) with various thicknesses of the silica layer. It is demonstrated that flagella can be utilized for the fabrication of SMFNs with tunable thickness. A thicker silica layer was obtained as the concentration ratio of TEOS and reaction time was increased. The present experimental evidence has shown the feasibility of using such fabrication techniques to manufacture nanotubes without genetic modification of flagella which retain the original morphology.

Direct recovery of spilled oil using hierarchically porous oil scoop with capillary-induced anti-oil-fouling.

The pitcher plant has evolved its hierarchically grooved peristome to enhance a water-based slippery system for capturing insects with oil-covered footpads. Based on this, we proposed a hierarchically porous oil scoop (HPOS) with capillary-induced oil peel-off ability for repeatable spilled oil recovery. As the HPOS scoops oil-water mixture, water passes through the hole while the oil is confined within a curved geometry. The filter in HPOS has three levels of porous structures; (1) 3D-printed mesh structure with sub-millimeter scale hole to filter out oil from an oil-water mixture, (2) internal micropore in fibers enhancing capillarity and water transport, (3) O2 plasma-induced high-aspect-ratio nanopillar structures imposing anti-oil-fouling property with capillary-induced oil peeling. As the oil-contaminated HPOS makes contact with water, water meniscus rises and peels off the oil immediately at the air-water interface. The oil-peel-off ability of the HPOS would prevent pores from clogging by oils for reuse. The study demonstrated that the HPOS recovers highly viscous oil (up to 5000 mm2·s-1) with a high recovery rate (>95%), leaving the filtered water with low oil content (<10 ppm), which satisfies the discharge criterion of 15 ppm.

Development of flagella bio-templated nanomaterials for electronics.

Bacterial flagella with their unique structural properties have proven to be promising bio-templates and can be exploited for the creation of nanomaterial with very high aspect ratio and surface area. Their chemically modifiable surfaces allow the flagella be modified to possess electrical/electronic properties. Their extraordinary physical properties along with the many possibilities for manipulation make them ideal systems to study for the purpose of developing nanoelectronics. First, this article reviews the characteristics of bacterial flagella and their utilization as biologically inspired templates. Next, the use of bio-templates for electronic systems such as dye-sensitized solar cell and lithium ion battery is discussed. Finally, we show the future directions for the use of flagella biotemplatednanomaterials for applications in electrical engineering fields.

Photon to thermal response of a single patterned gold nanorod cluster under near-infrared laser irradiation.

The potential applications of the photon to thermal conversion technique by gold nanorods has attracted attention for biomedical applications since they show an intense absorption spectrum in the near-infrared region, and therefore, penetrate more deeply into biological tissues. The goal in this study is to assess a local heating phenomenon with a single patterned cluster of gold nanorods that are prepared as a wet chemically synthesized gold nanorod solution and mixed with aqueous 1% alginate and 0.1 M calcium chloride. In particular, we utilized the initiated chemical vapor deposition method to coat the cluster with poly(2-hydroxyethyl methacrylate) to enhance its high temperature resistance in the solution. The influence of the thermal energy on the surroundings is studied by measuring the surface temperature of the single patterned gold nanorod cluster as a function of laser irradiation time. The experimental results were compared with numerical simulation results. The results showed that the irradiated gold nanorods could rapidly heat to maximum surface temperatures of over 60 °C within 120 s. Furthermore, the temperature remained almost constant (i.e. reached a steady state) under continuous laser irradiation and rapidly cooled to the initial temperature within 90 s when the laser was turned off.

The role of printing parameters and scaffold biopolymer properties in the efficacy of a new hybrid nano-bioprinting system.

We created a hybrid nano-bioprinting system, which combines the initial patterning capabilities of direct cell writing with the active patterning capabilities of superparamagnetic nanoparticles. Biofabrication conditions, including printing parameters and scaffold biopolymer properties, may affect cell viability, nanoparticle manipulation and patterning capabilities. Nanoparticles were printed under varied conditions either in the biopolymer or loaded inside cells. Cell viability, alginate viscosity, nanoparticle movement and printing resolution were measured. We now show that while nanoparticles decreased cell viability, nozzle size had no significant effect. High printing pressure decreased cell viability, but viability loss was not accentuated by nanoparticles. High nanoparticle concentrations increased alginate viscosity at higher alginate concentrations. Nanoparticle velocity in response to a magnetic field was a function of nanoparticle diameter and scaffold viscosity, which agreed with a mathematical model of nanoparticle movement. Finally, the nano-bioprinting system resolution and patterning precision were not affected by nanoparticles in the prepolymer solution. These data suggest that nanoparticle incorporation in solid freeform fabrication does not change biofabrication parameters unless high nanoparticle concentrations are used. Future work includes developing vascularized tissue engineering constructs using the nano-bioprinting system.