Development and validation of a dynamic mass-balance prediction model for indoor particle concentrations in an office room.

The Korean government recommends intermittent operation of air purifiers (APs) as a measure to maintain indoor particulate matter (PM) concentrations below the mandatory standards and reduce exposure to indr PM2.5 (PM with a diameter smaller than 2.5 µm). However, there is no guideline to inform occupants of when and how long APs should be operated to comply with the standards. In this study, we developed a dynamic mass-balance model to predict indoor PM concentrations in an office considering penetration of outdoor particles, change in number of occupants, and operational status of the AP. The model fit and prediction accuracies were verified using the American Society for Testing and Materials (ASTM) D 5157 criteria and the k-fold validation technique. We observed that indoor PM2.5 concentrations were determined by infiltration of outdoor PM2.5, and indoor generation/resuspension by occupants and removal. For PM2.5-10(2.5 µm

Inhaled underground subway dusts may stimulate multiple pathways of cell death signals and disrupt immune balance.

In this study, we aimed to identify a toxic mechanism and the potential health effects of ambient dusts in an underground subway station. At 24 h exposure to human bronchial epithelial (BEAS-2B) cells (0, 2.5, 10, and 40 µg/mL), dusts located within autophagosome-like vacuoles, whereas a series of autophagic processes appeared to be blocked. The volume, potential and activity of mitochondria decreased in consistent with a condensed configuration, and the percentage of late apoptotic cells increased accompanying S phase arrest. While production of reactive oxygen species, expression of ferritin (heavy chain) protein, secretion of IL-6, IL-8 and matrix metalloproteinases, and the released LDH level notably increased in dust-treated cells (40 µg/mL), intracellular calcium level decreased. At day 14 after a single instillation to mice (0, 12.5, 50, and 200 µg/head), the total number of cells increased in the lungs of dust-treated mice with no significant change in cell composition. The pulmonary levels of TGF-ß, GM-CSF, IL-12 and IL-13 clearly increased following exposure to dusts, whereas that of CXCL-1 was dose-dependently inhibited. Additionally, the population of cytotoxic T cells in T lymphocytes in the spleen increased relative to that of helper T cells, and the levels of IgA and IgM in the bloodstream were significantly reduced in the dust-treated mice. Subsequently, to improve the possibility of extrapolating our findings to humans, we repeatedly instilled dusts (1 time/week, 4 weeks, 0.25 and 1.0 mg/head) to monkeys. The total number of cells, the relative portion of neutrophils, the level of TNF-α significantly increased in the lungs of dust-treated monkeys, and the expression of cytochrome C was enhanced in the lung tissues. Meanwhile, the pulmonary level of MIP-α was clearly reduced, and the expression of caveolin-1 was inhibited in the lung tissues. More importantly, inflammatory lesions, such as granuloma, were seen in both mice and monkeys instilled with dusts. Taken together, we conclude that dusts may impair the host's immune function against foreign bodies by inhibiting the capacity for production of antibodies. In addition, iron metabolism may be closely associated with dust-induced cell death and inflammatory response.

Effects of air cleaners and school characteristics on classroom concentrations of particulate matter in 34 elementary schools in Korea.

Exposure to particulate matter (PM) in school environments has been associated with respiratory illnesses among children. Although using air cleaners was reported to reduce PM exposure and improve residents' health in homes, their effects in classrooms are not well understood. We examined how the use of air cleaners in classrooms and school/classroom characteristics affect the levels of indoor PM. Our environmental study included 102 classrooms from 34 elementary schools located on the mainland peninsula and an island in Korea. Indoor and outdoor PM were monitored simultaneously with portable aerosol spectrometers, and indoor gravimetric PM levels were measured with low volume, size-selective samplers during the class hours. Correlations among PM measurements were computed and final multiple regression models for indoor PM were constructed with a model building procedure. Correlation between indoor and outdoor PM2.5 (PM < 2.5 µm in aerodynamic diameter) was higher (r = 0.78, p < 0.01) than that of PM10 (PM < 10 µm) (r = 0.49, p < 0.01). School location, classroom occupant density, and ambient PM levels significantly (p-values<0.05) affected classroom PM concentrations. The adjusted PM levels in classrooms using air cleaners were significantly (p-values<0.01) lower by approximately 35% than in classrooms not using them. However, air cleaners appeared to remove PM2.5 more effectively than PM10, perhaps because coarse particles settle more rapidly than fine particles on surfaces, or their resuspension and generation rate by occupants exceeds the removal rate by air cleaners. Our study suggests that routine cleaning to remove surface dust along with the use of air cleaners might be required to effectively reduce occupants' exposure in classrooms.

Preparation of Mesoporous CuCe-Based Ternary Metal Oxide by Nano-Replication and Its Application to Decomposition of Liquid Monopropellant.

Mesoporous CuCe-based ternary metal oxides were synthesized using KIT-6 as a hard template through a nano-casting method. The mesoporous CuCe-based metal oxides were applied to the catalytic decomposition of the ammonium dinitramide-based liquid monopropellant. The decomposition onset temperature over the meso-CuCe ternary metal oxides was much lower than that over the CuCeOx catalyst prepared by conventional precipitation method. Higher activity of the meso-CuCe ternary metal oxides is attributed to higher surface area and larger pore size of the meso-CuCe ternary metal oxides than those of the conventional CuCe oxide. The highest activity of meso-CuCeZr catalyst among the meso-CuCe ternary metal oxide catalysts is likely due to the highest mesoporosity.

Ordered Mesoporous Cu-Mn Metal Oxides for the Catalytic Decomposition of an Energetic Ionic Liquid.

Ordered mesoporous Cu-Mn binary metal oxide (meso-CuMnOx) catalysts were successfully synthesized by a hard-templating method from a mesoporous silica template with a cubic Ia3d mesostructure (KIT-6) or hydrophobic KIT-6, exhibiting a well-developed crystalline framework, a regular pore size distribution and a high surface area. The copper and manganese elements in the mesoporous Cu-Mn binary metal oxides (meso-CuMnOx-N and meso-CuMnOx-HP), obtained from the KIT-6 and hydrophobic KIT-6, respectively, were homogeneously dispersed in the whole particles. The activities of meso-CuMnOx catalysts for the decomposition of a liquid monopropellant containing an energetic ionic liquid, ammonium dinitramide, were much higher than that over a CuMnOx catalyst prepared by a conventional precipitation method. This is attributed to the well-developed mesoporosity of the meso-CuMnOx catalysts. Among the mesoporous CuMnOx catalysts, the decomposition onset temperature over meso-CuMnOx-HP (87.9 °C) was found to be lower than that over meso-CuMnOx-N (100.4 °C), probably due to its higher mesoporosity and surface area.

Development of air purifier operation guidelines using grey box models for the concentrations of particulate matter in elementary school classrooms.

Considering the hazardous effects of particulate matter (PM) exposure on students and teachers and the high PM concentration issue in South Korea, air purifiers have recently been installed in most classrooms to improve air quality. However, some on-site challenges, such as operational costs and noise, have been issues with the continuous operation of air purifiers. Therefore, a guideline is needed to dynamically predict the indoor PM concentration based on the changes in outdoor PM concentration and activate the air purifiers only when necessary. This study develops a grey-box model that uses measured data and physical differential equations to perform the given objective and verifies its accuracy using ASTM D5157. Modeling and analysis results have obtained information that can form the basis for developing guidelines to address PM issues in schools: The air purifier should be operated during periods where the predicted values exceed the limit in closed windows and the air purifier is not operating. It was also confirmed that the need for the operation of the air purifier varies between schools and classrooms under the same outdoor PM concentration. Indoor PM concentration increased significantly after students' simultaneous mass movement, necessitating air purifiers' operation before and after the events. The prefilter of the heater also aided in the removal of coarse PM. Additionally, the limitations and future development directions of the model were discussed.

Subway station dust-induced pulmonary inflammation may be due to the dysfunction of alveolar macrophages: Possible contribution of bound elements.

With its increasing value as a means of public transportation, the health effects of the air in subway stations have attracted public concern. In the current study, we investigated the pulmonary toxicity of dust collected from an air purifier installed on the platform of the busiest subway station in Seoul. We found that the dust contained various elements which are attributable to the facilities and equipment used to operate the subway system. Particularly, iron (Fe), chromium (Cr), zirconium (Zr), barium (Ba), and molybdenum (Mo) levels were more notable in comparison with those in dust collected from the ventilation chamber of a subway station. To explore the health effects of inhaled dust, we first instilled via the trachea in ICR mice for 13 weeks. The total number of pulmonary macrophages increased significantly with the dose, accompanying hematological changes. Dust-laden alveolar macrophages and inflammatory cells accumulated in the perivascular regions in the lungs of the treated mice, and pulmonary levels of CXCL-1, TNF-α, and TGF-ß increased clearly compared with the control. The CCR5 and CD54 level expressed on BAL cell membranes was also enhanced following exposure to dust, whereas the CXCR2 level tended to decrease in the same samples. In addition, we treated the dust to alveolar macrophages (known as dust cells), lysosomal and mitochondrial function decreased, accompanied by cell death, and NO production was rapidly elevated with concentration. Moreover, the expression of autophagy- (p62) and anti-oxidant (SOD-2)-related proteins increased, and the expression of inflammation-related genes was dramatically up-regulated in the dust-treated cells. Therefore, we suggest that dysfunction of alveolar macrophages may importantly contribute to dust-induced inflammatory responses and that the exposure concentrations of Cr, Fe, Mo, Zr, and Ba should be considered carefully when assessing the health risks associated with subway dust. We also hypothesize that the bound elements may contribute to dust-induced macrophage dysfunction by inhibiting viability.

Subchronic pulmonary toxicity of ambient particles containing cement production-related elements.

Chronic respiratory disease is among the most common non-communicable diseases, and particulate materials (PM) are a major risk factor. Meanwhile, evidence of the relationship between the physicochemical characteristics of PM and pulmonary toxicity mechanism is still limited. Here, we collected particles (CPM) from the air of a port city adjacent to a cement factory, and we found that the CPM contained various elements, including heavy metals (such as arsenic, thallium, barium, and zirconium) which are predicted to have originated from a cement plant adjacent to the sampling site. We also delivered the CPM intratracheally to mice for 13 weeks to investigate the pulmonary toxicity of inhaled CPM. CPM-induced chronic inflammatory lesions with an increased total number of cells in the lung of mice. Meanwhile, among inflammatory mediators measured in this study, levels of IL-1ß, TNF-α, CXCL-1, and IFN-γ were elevated in the treated group compared with the controls. Considering that the alveolar macrophage (known as dust cell) is a professional phagocyte that is responsible for the clearance of PM from the respiratory surfaces, we also investigated cellular responses following exposure to CPM in MH-S cells, a mouse alveolar macrophage cell line. CPM inhibited cell proliferation and formed autophagosome-like vacuoles. Intracellular calcium accumulation and oxidative stress, and altered expression of pyrimidine metabolism- and olfactory transduction-related genes were observed in CPM-treated cells. More interestingly, type I-LC3B and full-length PARP proteins were not replenished in CPM-treated cells, and cell cycle changes, apoptotic and necrotic cell death, and caspase-3 cleavage were not significantly detected in cells exposed to CPM. Taken together, we conclude that dysfunction of alveolar macrophages may contribute to CPM-induced pulmonary inflammation. In addition, given the possible transformation of heart tissue observed in CPM-treated mice, we suggest that further study is needed to clarify the systemic pathological changes and the molecular mechanisms following chronic exposure to CPM.

Influence of pleat geometry on filter cleaning in PTFE/glass composite filter.

A pleated filter bag is often used to treat exhaust gas in many industrial applications, due to its fairly high dust collection efficiency and relatively low pressure drop. This work deals with the optimum pleating geometries of a pleated filter made with a newly developed PTFE/glass composite filter. It was found that pleating geometries, including pleat height and pleat pitch, directly affect the cleaning efficiency The design index, alpha, which stands for the ratio of pleat height to pleat pitch, is 1.48 for optimum operation. When the alpha value was higher than 1.48, the pressure drop across the pleated filter medium increased, resulting in a decreased cleaning interval due to the difficulty of filter cleaning. Therefore, it is necessary that the optimum pleating geometry should be determined by employing the dimensionless parameter, alpha, in the design of cartridge filters.

Toluene vapor capture by activated carbon particles in a dual gas-solid cyclone system.

Capturing of odorous compounds such as toluene vapor by a particulate-activated carbon adsorbent was investigated in a gas-solid cyclone, which is one type of mobile beds. The test cyclone was early modified with the post cyclone (PoC) and a spiral flow guide to the vortex finder. The proposed process may contribute to the reduction of gases and dust from industrial exhausts, especially when dealing with a low concentration of odorous elements and a large volume ofdust flow. In this device, the toluene capturing efficiency at a 400 ppm concentration rose up to 77.4% when using activated carbon (AC) particles with a median size of 27.03 microm. A maximum 96% of AC particles could be collected for reuse depending on the size and flow rate. The AC regenerated via thermal treatment showed an adsorption potential up to 66.7% throughout repeated tests.

Evaluation of moisture effect on low-level CO2 adsorption by ion-exchanged zeolite.

To enhance the capture of low-level indoor CO2, a commercial zeolite (13X) was modified with alkali and alkaline earth metals using an ion-exchange method. Although the calcium-impregnated sorbent (zeo-Ca) showed the largest adsorption capacity, with a strong binding force for carbon dioxide, its regeneration by heat treatment was very difficult. Moisture in the gas flow caused significant decreases in CO2 adsorption capability as well as in the lifetime of the adsorbents. As for the regeneration gas, the test showed that nitrogen would hinder the CO2 adsorption more significantly than helium gas. Water vapour and nitrogen gas molecules are apt to competitively occupy the available sites of the adsorbent over the CO2 molecules.

Decomposition of VOCs using serial surface dielectric barrier discharge reactors.

Decomposition of two typical volatile organic compounds (VOCs): toluene and methyl ethyl ketone (MEK), was investigated by introducing the complete energy yield (i.e. amount of VOCs totally converted to CO and CO2 for every 1 kWh of electrical usage) and specific energy density (SED) for the non-thermal plasma technology. Three dielectric barrier discharge reactors of which SED range was 55 J/L to 283 J/L at a flow rate of 1 L/min were connected in a 3-reactor arranged in series using interconnecting tubes in the inlets and outlets. As a result of the serial reactor design, the energy efficiency of the system improved, and in particular, 7% of increase was found in at the same level of energy consumption. The mixed phase of VOCs (toluene and MEK) showed MEK as a limiting species in this study. As the inlet concentration rose from 20 to 100 ppmv, both energy yield and complete energy yield increased from 0.8 to 9.2 g/kWh and from 0.8 to 2.3 g/kWh, respectively.

Decomposition of Hydroxylammonium Nitrate Solution Over Nanoporous CuO Supported on Honeycomb.

We investigated the influence of a copper loading strategy over a honeycomb structure on the catalytic performance during the decomposition of a hydroxylammonium nitrate (HAN) aqueous solution. Copper was supported on the honeycomb surface by means of a metal coating method (MC), i.e., a method of directly coating a metal, and a metal alumina coating method (MAC), i.e., a method of coating a mixture of metal and alumina. The properties of the catalysts were analyzed by N2 adsorption, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The Cu(16.8)/honeycomb-MC catalyst showed a lower decomposition onset temperature during the decomposition of the HAN aqueous solution compared to that over the Cu(7.0)/honeycomb- MAC catalyst, an outcome ascribed to the higher copper loading and the higher dispersion of copper in the Cu(16.8)/honeycomb-MC catalyst compared to that in the other catalyst. The Cu(16.8)/honeycomb-MC catalyst was confirmed to have both excellent activity and heat resistance during the decomposition of a HAN aqueous solution.

ZnO-Impregnated Polyacrylonitrile Nanofiber Filters against Various Phases of Air Pollutants.

The incorporation of metal oxide nanoparticles (NPs) in fiber filters is an effective approach to enhance the specific surface area and surface roughness of the fiber, hence improving their efficiency for fine dust capture and other gas treatment or biological applications. Nevertheless, uneven distribution of NPs limits their practical applications. In this study, a commercial silane coupling agent (3-methacryloxypropyltrimethoxysilane) was used to improve the dispersion of zinc oxide (ZnO) NPs in thin polyacrylonitrile fibers. Scanning electron microscopy (SEM) revealed that the fibers incorporating the silane-modified NPs exhibited better distribution of NPs than those prepared with pristine ZnO NPs. The silane modification enhanced the specific surface area, surface roughness, and fiber porosity. In particular, the nanofiber filter incorporating 12 wt% ZnO NPs modified with 0.5 g silane per g of ZnO NPs maintained a filtration efficiency of 99.76% with a low pressure drop of 44 Pa, excellent antibacterial activity, and could decompose organic methylene blue dye with an efficiency of 85.11% under visible light.

Characterization and source identification of fine dust in Seoul elementary school classrooms.

To evaluate the level of fine particulate matters in elementary schools located in a high traffic area of Seoul and verify the emission source, a field study on the classrooms was conducted under the uncontrolled condition. The indoor PM2.5 was lower than that of the outdoors as indicated by an I/O ratio of 0.52-0.92 based on mass concentration, and it was maintained below the National Guideline. Heavy metals such as Cr, Mn, Ni, Cu, Zn, As, Sn and Pb were lower in indoor PM2.5 than outdoors. On the contrary, carbons including OC and EC were higher in indoor PM2.5. As a result of source apportionment analysis, an outdoor emission source was responsible for 58.5% of the classroom PM2.5. This study can contribute to urban planning and school design to keep children safe from harmful environments.

Effect of fattening period on growth performance, carcass characteristics, and economic traits of Holstein steers.

This study was conducted to investigate the effect of different fattening periods on the growth performance, carcass characteristics, and economic traits of Holstein steers. Sixty Holstein steers (8.0 ± 0.28 months old) with an average body weight (BW) of 231.88 ± 2.61 kg, were randomly allocated to five different fattening period treatments: 20, 21, 22, 23, and 24 months (n = 12 in each treatment group). Final BW and average daily gain (ADG) did not differ among the treatment groups during the early fattening period. At the late stage of the fattening period, the final BW of steers in the 24-month treatment group (812.84 kg) was greater (p < 0.05) than that of steers in the 20-month treatment group (750.39 kg). During the same period, steers in the 20- and 21-month treatment groups had a significantly higher (p < 0.05) ADG than those in the 22-month treatment group. The highest ADG (1.36 kg/day) was found in the 20-month treatment group (1.36), followed by the 21- (1.33 kg/day), 22- (1.22 kg/day), 23- (1.21 kg/day), and 24- (1.14 kg/day) month treatment groups. The feed conversion ratio (FCR) increased as the fattening period increased, and the FCR was 12.88% lower in the 20-month treatment group than in the 24-month treatment group. However, no significant differences were detected in back-fat thickness, loin area, marbling score, and chemical characteristics (water, crude protein, and crude fat content) among the treatment groups. The composition of fatty acids including C18:0, C18:1, saturated fatty acids, unsaturated fatty acids, and poly-unsaturated fatty acids did not differ among the experimental groups. As the fattening period increased, production costs increased, resulting in a decrease in gross income. The gross income for steers in the 24-month treatment group was 35.8% and 23.5% lower than that for steers in the 20- and 21-month treatment groups, respectively. Taken together, the best performance, including the ADG, FCR, and gross income, was obtained when the fattening program of the Holstein steers lasted 20 months.

Preparation and characterization of porous composite filter medium by polytetrafluoroethylene foam coating.

The high costs of ceramic and Teflon filter media for hot gas cleaning has limited their industrial applications. This paper presents a foam coating technology that can be used to produce an inexpensive and highly efficient filter for industrial applications. A new apparatus was designed and built that coats porous glass mats with liquid-phase polytetrafluoroethylene (PTFE). The machine generates bubbles, enables the formation of uniform micropores less than 45 microm in diameter, and produces a product with air permeability greater than 5.5 cm3/cm2/sec. The resulting filter was found to be thermally stable up to 270 degrees C without any visible distortion and was comparable in dust collection efficiency to other commercial filter media. In addition, its de-dusting efficiency was greater than 85%, which is similar to that of other test filter media.

TEPA impregnation of electrospun carbon nanofibers for enhanced low-level CO2 adsorption.

The CO2 adsorption selectivity of plain activated carbon nanofibers (ANF) is generally low. For enhancement, nitrogen functionalities favorable for CO2 adsorption are usually tethered to the ANF. In the current study, we adopted chemical impregnation using 0.5 wt% tetraethylenepentamine (TEPA) solution as an impregnant. To enhance the impregnation of TEPA further, preliminary oxidation of the nanofibers with 70% HNO3 was conducted. The effects of HNO3 and TEPA treatments on the modified ANFs were investigated for physical (using N2 monosorb, thermogravimetric analyzer, scanning electron microscopy) and chemical (X-ray photoelectron spectrometer) changes. From the results, we found that although TEPA impregnation reduced the specific surface area and pore volume of the ANFs (from 673.7 and 15.61 to 278.8 m2/g and 0.284 cm3/g, respectively), whereas the HNO3 pre-oxidation increased the number of carboxylic groups on the ANF. Upon TEPA loading, pyridinic nitrogen was tethered and further enhanced by pre-oxidation. The surface treatment cumulatively increased the amine content from 5.81% to 13.31%. Consequently, the final adsorption capacity for low (0.3%) and pure CO2 levels were enhanced from 0.20 and 1.89 to 0.33 and 2.96 mmol/g, respectively. Hence, the two-step pre-oxidation and TEPA treatments were efficient for improved CO2 affinity.

Life-threatening bleeding with intussusception due to gastrointestinal stromal tumor: a case report.

BACKGROUND: Massive intraluminal bleeding requires urgent intervention and management. However, the source of bleeding on the small intestine is difficult to determine. Intestinal tumor with intussusception is a rare and normally not an urgent condition. Herein, we present a rare case of intestinal intussusception with massive bleeding due to jejunal gastrointestinal stromal tumor (GIST) that required emergency surgical treatment. CASE PRESENTATION: A 51-year-old male was admitted to the emergency department complaining of abdominal pain and acute hematochezia. Esophagogastroduodenoscopy (EGD) and colonoscopy could not determine the source of the bleeding site. Abdominal pelvic computed tomography (AP-CT) revealed GIST with intussusception, strongly suggestive of distal jejunal bleeding. Unresponsive transfusion with low blood pressure and continuous hematochezia led to emergency laparotomy. GIST, which was the leading point for intussusception, was located in the jejunum and showed mucosal ulceration of approximately 3.5 cm in diameter. Following resection and functional anastomosis, histology revealed a GIST with low mitotic count (< 5 per 50HPF). Moreover, immunochemical analysis revealed positivity for c-kit (CD117) and DOG-1. There were no complications 2 months after surgery. CONCLUSIONS: Intussusception associated with GIST is a rare finding that can be life-threatening if it occurs with an ulcer. This case showed that the early detection of bleeding and emergency surgery could prevent severe complications.

Catalytic Decomposition of an Ionic Liquid Monopropellant Over Ir/Hexaaluminate Catalysts.

The aim of this study is to elucidate the influence of an iridium loading strategy over hexaaluminate on the catalytic performance during the decomposition of liquid monopropellants based on ammonium dinitramide (ADN). Powder-type and pellet-type Ir/hexaaluminate catalysts were prepared and their chemico-physical properties were characterized by N2 adsorption, XRD, XRF, and SEM. There were considerable differences in the Ir amounts present on the surface according to the impregnation method employed. The catalytic activities of three types of Ir/hexaaluminate catalysts to decompose the ADN-based liquid monopropellant were compared using a semi-batch type of reactor. Pellet-type Ir/hexaaluminate catalyst, which formed hexaaluminate into a pellet and where iridium was impregnated during the last stage, showed the lowest onset temperature during the decomposition of the ADN-based liquid monopropellant, having the effect of lowering the decomposition onset temperature by around 60 °C compared to that without a catalyst. This was due to the pellet-type Ir/hexaaluminate having a larger surface area and a large number of Ir active sites on its surface.