Quantitative mechanical analysis of thin compressible polymer monolayers on oxide surfaces.

A clear understanding of the mechanical behavior of nanometer thick films on nanostructures, as well as developing versatile approaches to characterize their mechanical properties, are of great importance and may serve as the foundation for understanding and controlling molecular interactions at the interface of nanostructures. Here we report on the synthesis of thin, compressible polyethylene glycol (PEG) monolayers with a wet thickness of <20 nm on tin dioxide (SnO2) nanofibers through silane-based chemistries. Nanomechanical properties of such thin PEG films were extensively investigated using atomic force microscopy (AFM). In addition, tip-sample interactions were carefully studied, with different AFM tip modifications (i.e., hydrophilic and hydrophobic) and in different ionic solutions. We find that the steric forces dominate the tip-sample interactions when the polymer film is immersed in solution with salt concentrations similar to biological media (e.g., 1x phosphate buffer solution), while van der Waals and electrostatic forces have minimal contributions. A Dimitriadis thin film polymer compression model shows that the linear elastic regime is reproducible in the initial 50% indentation of these films which have tunable Young's moduli ranging from 5 MPa for the low molecular weight films to 700 kPa for the high molecular weight PEG films. Results are compared with the same PEG films deposited on silicon substrates which helped quantify the structural properties and understand the relationship between the structural and the mechanical properties of PEG films on the SnO2 fibers.

Nanofiber near-field light-matter interactions for enhanced detection of molecular level displacements and dynamics.

We experimentally demonstrate that plasmonic nanoparticles embedded in the evanescent field of subwavelength optical waveguides (WGs) are highly sensitive to distances normal to the propagation of light, showing an ~10× increase in spatial resolution compared to the optical field decay of the WG. The scattering cross-section of the Au nanoparticle is increased by the plasmon-dielectric coupling interaction when the nanoparticle is placed near the dielectric surface of the WG, and the decay of the scattering signal is enhanced, showing angstrom level distance sensitivity within 10 nm from the WG. Numerical studies with the finite-difference time-domain (FDTD) method correlate well with the experimental results. To demonstrate real-time monitoring of a single molecule stretching in the evanescent field, we linked individual single-stranded DNA molecules between the WG and plasmonic nanoparticles and pushed on the nanoparticles with fluidic forces. The simple design and ease of obtaining optical feedback on molecular displacements makes our approach ideal for new in situ force sensing devices, imaging technologies, and high-throughput molecular analysis.

Stimulus-responsive light coupling and modulation with nanofiber waveguide junctions.

We report a systematic study of light coupling at junctions of overlapping SnO(2) nanofiber waveguides (WGs) as a function of gap separation and guided wavelength. The junctions were assembled on silica substrates using micromanipulation techniques and the gap separation was controlled by depositing thin self-assembled polyelectrolyte coatings at the fiber junctions. We demonstrate that the coupling efficiency is strongly dependent on the gap separation, showing strong fluctuations (0.1 dB/nm) in the power transfer when the separation between nanofibers changes by as little as 2 nm. Experimental results correlate well with numerical simulations using three-dimensional finite-difference time-domain techniques. To demonstrate the feasibility of using coupled nanofiber WGs to modulate light, we encased the junctions in an environment-responsive matrix and exposed the junctions to gaseous vapor. The nanofiber junctions show an ~95% (or ~80%) modulation of the guided 450 nm (or 510 nm) light upon interaction with the gaseous molecules. The results reveal a unique nanofiber-based sensing scheme that does not require a change in the refractive index to detect stimuli, suggesting these structures could play important roles in localized sensing devices including force-based measurements or novel chemically induced light modulators.

Matrix-assisted energy conversion in nanostructured piezoelectric arrays.

We demonstrate an organic/inorganic hybrid energy-harvesting platform, based on nanostructured piezolelectric arrays embedded in an environmental-responsive polymer matrix, which can self-generate electrical power by scavenging energy from the environment. A proof of principle device is designed, fabricated, and tested using vertically aligned ZnO nanowires and heat as the local energy source. The device layout takes advantage of the collective stretching motion of piezoelectric ZnO NWs, induced by the shape-change of the matrix polymer, to convert the thermal energy into direct current with output power densities of ∼20 nW/cm(2) at a heating temperature of ∼65 °C. The responsive nature of polymeric matrices to various stimuli makes this nanostructured piezoelectric architecture a highly versatile approach to scavenging energy from a multitude of environments including fluid-based and chemical-rich systems.

Tunable Surface and Matrix Chemistries in Optically Printed (0-3) Piezoelectric Nanocomposites.

In this work, the impacts of varying surface modification, matrix parameters, and fabrication conditions on the performance of optically printed (0-3) piezoelectric polymer nanocomposites are examined. For example, we find that a 75% reduction in nanoparticle edge-length boosted the piezoelectric coefficient (d33) by over 100%. By optimizing the composition and fabrication conditions, 10% by mass loading barium titanate nanocomposites are able to yield d33 values of ∼80 pC/N compared to <5 pC/N when parameters are not optimized. With a more complete understanding of how to enhance the performance of (0-3) piezoelectric polymer nanocomposites, these materials should find use in a wide range of applications.

Piezoelectric nanoparticle-polymer composite foams.

Piezoelectric polymer composite foams are synthesized using different sugar-templating strategies. By incorporating sugar grains directly into polydimethylsiloxane mixtures containing barium titanate nanoparticles and carbon nanotubes, followed by removal of the sugar after polymer curing, highly compliant materials with excellent piezoelectric properties can be fabricated. Porosities and elasticity are tuned by simply adjusting the sugar/polymer mass ratio which gave an upper bound on the porosity of 73% and a lower bound on the elastic coefficient of 32 kPa. The electrical performance of the foams showed a direct relationship between porosity and the piezoelectric outputs, giving piezoelectric coefficient values of ∼112 pC/N and a power output of ∼18 mW/cm3 under a load of 10 N for the highest porosity samples. These novel materials should find exciting use in a variety of applications including energy scavenging platforms, biosensors, and acoustic actuators.

3D optical printing of piezoelectric nanoparticle-polymer composite materials.

Here we demonstrate that efficient piezoelectric nanoparticle-polymer composite materials can be optically printed into three-dimensional (3D) microstructures using digital projection printing. Piezoelectric polymers were fabricated by incorporating barium titanate (BaTiO3, BTO) nanoparticles into photoliable polymer solutions such as polyethylene glycol diacrylate and exposing to digital optical masks that could be dynamically altered to generate user-defined 3D microstructures. To enhance the mechanical-to-electrical conversion efficiency of the composites, the BTO nanoparticles were chemically modified with acrylate surface groups, which formed direct covalent linkages with the polymer matrix under light exposure. The composites with a 10% mass loading of the chemically modified BTO nanoparticles showed piezoelectric coefficients (d(33)) of ∼ 40 pC/N, which were over 10 times larger than composites synthesized with unmodified BTO nanoparticles and over 2 times larger than composites containing unmodified BTO nanoparticles and carbon nanotubes to boost mechanical stress transfer efficiencies. These results not only provide a tool for fabricating 3D piezoelectric polymers but lay the groundwork for creating highly efficient piezoelectric polymer materials via nanointerfacial tuning.

Profiling the evanescent field of nanofiber waveguides using self-assembled polymer coatings.

Here we demonstrate a facile method of quantifying the decaying optical field surrounding free-standing tin dioxide (SnO(2)) nanofiber waveguides. Through the use of thin self-assembled polyelectrolyte coatings and fluorescent optical transmitters we map out the optical intensity as a function of distance with nanometer resolution.