Simultaneously Passivating Cation and Anion Defects in Metal Halide Perovskite Solar Cells Using a Zwitterionic Amino Acid Additive.

Ionic defects (e.g., organic cations and halide anions), preferably residing along grain boundaries (GBs) and on perovskite film surfaces, are known to be a major source of the notorious environmental instability of perovskite solar cells (PeSCs). Although passivating ionic defects is desirable, previous approaches using Lewis base or acid molecules as additives suppress only the negatively or positively charged defects, thus leaving oppositely charged defects. In this work, both the cationic and anionic defects inside methyl ammonium lead tri-iodide (MAPbI3 ) are simultaneously passivated by introducing a zwitterionic form of the amino acid, L-alanine, into the precursor solution as an additive. L-alanine has both positive (NH3+ ) and negative (COO- ) functional groups at a specific solvent pH, thereby passivating both the cation and anion defects in MAPbI3 . The addition of L-alanine increases the grain size of the perovskite crystals and lengthens the charge carrier lifetime (τ > 1 µs), leading to improved power conversion efficiencies (PCEs) of 20.3% (from 18.3% without an additive) for small-area (4.64 mm2 ) devices and 15.6% (from 13.5%) for large-area submodules (9.06 cm2 ). More importantly, the authors' approach also significantly enhances the shelf storage and photoirradiation stabilities of PeSCs.

Efficient Nanoscale Exciton Transport in Non-Fullerene Organic Solar Cells Enables Reduced Bimolecular Recombination of Free Charges.

The highest-efficiency organic photovoltaic (OPV)-based solar cells, made from blends of electron-donating and electron-accepting organic semiconductors, are often characterized by strongly reduced (non-Langevin) bimolecular recombination. Although the origins of the reduced recombination are debated, mechanisms related to the charge-transfer (CT) state and free-carrier encounter dynamics controlled by the size of donor and acceptor domains are proposed as underlying factors. Here, a novel photoluminescence-based probe is reported to accurately quantify the donor-acceptor domain size in OPV blends. Specifically, the domain size is measured in high-efficiency non-fullerene acceptor (NFA) systems and a comparative conventional fullerene system. It is found that the NFA-based blends form larger domains but that the expected reductions in bimolecular recombination attributed to the enhanced domain sizes are too small to account for the observed reduction factors. Further, it is shown that the reduction of bimolecular recombination is correlated to enhanced exciton dynamics within the NFA domains. This indicates that the processes responsible for efficient exciton transport also enable strongly non-Langevin recombination in high-efficiency NFA-based solar cells with low-energy offsets.

Photopically Transparent Organic Solar Cells with Tungsten Oxide-Based Multilayer Electrodes.

The tailoring of the average photopic transmittance (APT) of transparent organic solar cells (T-OSCs) has been the greatest challenge in building-integrated photovoltaic applications for future smart solar windows to regulate indoor brightness, maintain a human circadian rhythm, and positively impact human emotions by allowing the observation of the external environment. However, a notorious trade-off exists between the APT and power conversion efficiency (PCE) of T-OSCs, mainly due to the absence of highly conductive and transparent top electrodes, which are a key building block determining the PCE and APT. Herein, we demonstrate a new tungsten oxide (WO3)-based multilayer as a highly conductive and transparent top electrode that provides an excellent APT while maintaining a high PCE in T-OSCs. With the assistance of optical simulation based on a transfer matrix method to calculate the optimum thicknesses of the multilayer electrodes, we achieve the best-performing T-OSC with a PCE of 7.0% and a full device APT of 46.7%, resulting in a high light utilization efficiency of 3.27%, which is superior to that of T-OSCs based on the same photoactive system. Furthermore, superior thermal stability at 85 °C in an N2 atmosphere is observed in WO3-based T-OSCs, maintaining 98% of the initial PCE after about 231 h. Our findings provide new insights into the development of T-OSCs with high efficiency and transparency.

Efficient and Stable Perovskite Solar Cells with a High Open-Circuit Voltage Over 1.2 V Achieved by a Dual-Side Passivation Layer.

Suppressing nonradiative recombination at the interface between the organometal halide perovskite (PVK) and the charge-transport layer (CTL) is crucial for improving the efficiency and stability of PVK-based solar cells (PSCs). Here, a new bathocuproine (BCP)-based nonconjugated polyelectrolyte (poly-BCP) is synthesized and this is introduced as a "dual-side passivation layer" between the tin oxide (SnO2 ) CTL and the PVK absorber. Poly-BCP significantly suppresses both bulk and interfacial nonradiative recombination by passivating oxygen-vacancy defects from the SnO2 side and simultaneously scavenges ionic defects from the other (PVK) side. Therefore, PSCs with poly-BCP exhibits a high power conversion efficiency (PCE) of 24.4% and a high open-circuit voltage of 1.21 V with a reduced voltage loss (PVK bandgap of 1.56 eV). The non-encapsulated PSCs also show excellent long-term stability by retaining 93% of the initial PCE after 700 h under continuous 1-sun irradiation in nitrogen atmosphere conditions.

Highly stable and efficient cathode-buffer-layer-free inverted perovskite solar cells.

A simpler and less expensive fabrication process is one of the essential demands for the commercialization of perovskite solar cells (PeSCs). Especially, inverted PeSCs (I-PeSCs) require a cathode buffer layer (CBL) for fabricating highly efficient and stable PeSCs. However, this increases the number of fabrication step. Here, we demonstrate highly stable and efficient cathode-buffer-layer-free I-PeSCs via additive engineering on an ETL, which is based on phenyl-C61-butyric acid methyl ester (PC61BM) with a small amount of poly(methyl methacrylate) (PMMA). This modified ETL shows not only a simplified fabrication process but also effective extraction of charge from the perovskite to a high work function copper electrode (Cu) by formation of an interfacial dipole at the interfaces between the ETL and the Cu. Additionally, it exhibits good passivation of the trap density existing along the grain boundaries and surface of the perovskite layer, reducing the non-radiative recombination and consistent with the increases in open-circuit voltage (Voc). As a result, I-PeSCs with a blend PC61BM : PMMA ETL demonstrate an enhancement in the power conversion efficiency (PCE) from 13.55% (without PMMA) to 18.38%. Furthermore, they exhibit both burn-in-free behaviour in photostability measurements by maximum power-point tracking (MPPT) method and long-term air-stability (30 days for T90) in ambient air. Lastly, we obtained PCE of 15.03% and 16.83% for large-area (1 cm2) I-PeSCs with PC61BM and PC61BM : PMMA, respectively. This method provides an alternative route to reduce the fabrication time and budget for commercialization of I-PeSCs without sacrificing device performance.

Synthesis and application of amine-containing conjugated small molecules for the automatic formation of an electron transporting layer via spontaneous phase separation from the bulk-heterojunction layer.

Carbazole-based conjugated small molecule electrolytes (CSEs) containing different numbers of amine groups were synthesized and applied to bulk-heterojunction (BHJ) organic solar cells for the formation of a spontaneous self-assembled electron transporting layer (ETL). The active layer was spin-coated with a mixture solution containing the BHJ materials and a small amount of CSE, and a thin layer of CSE was formed underneath the active layer (CSE/BHJ bi-layer) via spontaneous phase separation, which is confirmed by the depth profile of the time of flight secondary ion mass spectroscopy (ToF-SIMS) spectrum. The amino groups in the CSEs form hydrogen-bonds with the surface of indium tin oxide (ITO), which acts as an ETL in BHJ solar cells. Moreover, the formed CSE layer is capable of changing the effective work function (WF) of ITO. An increasing number of amino groups in the CSEs (from Cz1N to Cz3N) provides more reduction of the effective WF of ITO, which results in a lower internal resistance and a higher power conversion efficiency (PCE). Furthermore, the enhanced hydrogen bonding between the amines and ITO with an increased number of amine groups has been studied by XPS. This result suggests that one-step processing provides a reduction of the manufacturing cost, which can provide an attractive design concept for ETL fabrication.