High-Performance Electrochemical and Photoelectrochemical Water Splitting at Neutral pH by Ir Nanocluster-Anchored CoFe-Layered Double Hydroxide Nanosheets.

Highly efficient electrocatalysts for the oxygen evolution reaction (OER) in neutral electrolytes are indispensable for practical electrochemical and photoelectrochemical water splitting technologies. However, there is a lack of good, neutral OER electrocatalysts because of the poor stability when H+ accumulates during the OER and slow OER kinetics at neutral pH. Herein, we report Ir species nanocluster-anchored, Co/Fe-layered double hydroxide (LDH) nanostructures in which the crystalline nature of LDH-restrained corrosion associated with H+ and the Ir species dramatically enhanced the OEC kinetics at neutral pH. The optimized OER electrocatalyst demonstrated a low overpotential of 323 mV (at 10 mA cm-2) and a record low Tafel slope of 42.8 mV dec-1. When it was integrated with an organic semiconductor-based photoanode, we obtained a photocurrent density of 15.2 mA cm-2 at 1.23 V versus reversible hydrogen in neutral electrolyte, which is the highest among all reported photoanodes to our knowledge.

ZnFe2 O4 Dendrite/SnO2 Helix 3D Hetero-Structure Photoanodes for Enhanced Photoelectrochemical Water Splitting: Triple Functions of SnO2 Nanohelix.

An array of SnO2 nanohelix structures is employed to fabricate a SnO2 helix@ZnFe2 O4 dendrite core-shell 3D heterostructure photoanode for photoelectrochemical (PEC) water splitting. The SnO2 helix provides triple critical functions to enhance the PEC performance of the photoanode. First, it scatters the incident light to achieve a higher light harvesting efficiency. Second, it provides a facile electron pathway as an electron transfer layer (ETL) while blocking hole transport to mitigate charge recombination in the bulk of ZnFe2 O4 . Finally, it becomes a template for the formation of ZnFe2 O4 dendrite nanostructure shell. The ZnFe2 O4 dendrite/SnO2 helix photoanode exhibits a remarkable increase in incident photon-to-electron conversion efficiency compared to unmodified ZnFe2 O4 with no ETL and modified one with "flat" SnO2 ETL. The surface of the ZnFe2 O4 /SnO2 helix photoanode is further modified with TiO2 passivation layer and NiFeOx oxygen evolution co-catalyst to achieve one of the best PEC performances among reported ZnFe2 O4 -based photoanodes.

Lyotropic Boron Nitride Nanotube Liquid Crystals: Preparation, Characterization, and Wet-Spinning for Fabrication of Composite Fiber.

Microfiber fabrication via wet-spinning of lyotropic liquid crystals (LCs) with anisotropic nanomaterials has gained increased attention due to the microfibers' excellent physical/chemical properties originating from the unidirectional alignment of anisotropic nanomaterials along the fiber axis with high packing density. For wet-spinning of the microfibers, however, preparing lyotropic LCs by achieving high colloidal stability of anisotropic nanomaterials, even at high concentrations, has been a critically unmet prerequisite, especially for recently emerging nanomaterials. Here, we propose a cationically charged polymeric stabilizer that can efficiently be adsorbed on the surface of boron nitride nanotubes (BNNTs), which provide steric hindrance in combination with Coulombic repulsion leading to high colloidal stability of BNNTs up to 22 wt %. The BNNT LCs prepared from the dispersions with various stabilizers were systematically compared using optical and rheological analysis to optimize the phase behavior and rheological properties for wet-spinning of the BNNT LCs. Systematic optical and mechanical characterizations of the BNNT microfibers with aligned BNNTs along the fiber axis revealed that properties of the microfibers, such as their tensile strength, packing density, and degree of BNNT alignment, were highly dependent on the quality of BNNT LCs directly related to the types of stabilizers.