RESUMO
PURPOSE: Using a high level of mannitol as a diluent in oral formulations can potentially result in tablet defects (e.g., chipping, cracking) during compression. This work aims to scrutinize the linkage between the mechanical properties and material attributes of mannitol and also uncover how variations between vendors and lots can lead to significant changes in the compaction performance of tablet formulations containing mannitol. METHODS: The mechanical properties (Poisson's ratio, fracture energy) and mechanical performance (ejection force, pressure transmission ratio, residual radial die-wall stress, and tensile strength) of mannitol compacts were assessed on a compaction simulator for four lots of mannitol from two different vendors. The variation of material attributes of each lot, including particle size distribution (PSD), crystal form, primary crystal size and morphology, specific surface area (SSA), powder flow, and moisture absorption were investigated. RESULTS: The variability of material attributes in mannitol lots, especially primary crystal size and SSA, can result in significant changes in mechanical properties and mechanical performance such as ejection force and residual radial die-wall stresses, which potentially led to chipping during compression. CONCLUSION: The study elucidated the linkage between fundamental material attributes and mechanical properties of mannitol, highlighting their impact on tablet defects and compaction performance in compression. A comprehensive understanding of the variability in mannitol properties between vendors and lots is crucial for successful formulation development, particularly when high percentages of mannitol are included as a brittle excipient.
Assuntos
Manitol , Fenômenos Mecânicos , Manitol/química , Fenômenos Químicos , Excipientes/química , Resistência à Tração , Comprimidos/química , Composição de Medicamentos , Tamanho da Partícula , Pós/químicaRESUMO
Spray drying is commonly used to produce amorphous solid dispersions (ASD) to improve the bioperformance of poorly water-soluble drugs. In this study, imaging techniques such as focused ion beam-scanning electron microscopy (FIB-SEM) and X-ray microcomputed tomography (XRCT) were used to study the microstructure of spray dried (SD) particles. Spray drying at higher outlet temperature (Tout) was found to produce more spherical hollow particles with smooth surface and thinner walls, while more raisin-like particles with thicker walls were generated at lower Tout. For the first time, an artificial intelligence-facilitated XRCT image analysis tool was developed to make quantitative analysis of thousands of particles individually possible. The particle size distribution through XRCT image analysis is generally in line with what is measured by laser diffraction. The image analysis reveals envelope density as a more sensitive physical attribute for process change than conventional bulk/tap density. Further, the tensile strength of SD particle compacts correlates with the particle wall thickness, and this is likely caused by the larger interparticle contact area generated by more deformation of particles with thinner walls. The knowledge gained here can help enable SD particle engineering and drug product with more robust process and optimized performance.
Assuntos
Inteligência Artificial , Água , Varredura Diferencial de Calorimetria , Microscopia Eletrônica de Varredura , Tamanho da Partícula , Pós , Microtomografia por Raio-XRESUMO
The cause of tablet defects, such as cracking, bubbling, and capping, during compression is currently not fully understood. Prior experimental work suggests that an increase in internal air pressure on powder compression can directly contribute to the formation of cracks within a tablet. The present study examines the air pressure increase on compression in a fully two-dimensional axisymmetric tablet geometry while being coupled to a plasticity model describing the evolution of tablet relative density on consolidation. It is shown numerically that increasing compression speed results in a large air pressure increase on the order of 1-1.5 MPa which approaches the diametrical tensile strength of tablets. In addition, it is shown experimentally through X-ray microcomputed tomography scans of tablets made at various dwell times that increasing dwell times equivalent to that on a tablet press has no effect on the degree of cracking within the tablet. Only when dwell times reach a time scale of 10 to 100 s does the air pressure diminish to a point at which cracking is eliminated. The reduction in air pressure during these extended dwells is captured by the current model. The experimental and numerical work presented here couples for the first time an air pressure model and plasticity model on compression. In addition, it provides a foundation for understanding how realistic tableting aspects such as precompression and tablet size impact the air pressure increase on consolidation.
Assuntos
Pressão do Ar , Composição de Medicamentos/métodos , Modelos Químicos , Comprimidos/química , Química Farmacêutica , Pós , Resistência à Tração , Fatores de Tempo , Microtomografia por Raio-XRESUMO
Fused deposition modeling (FDM) 3D printing (3DP) has a potential to change how we envision manufacturing in the pharmaceutical industry. A more common utilization for FDM 3DP is to build upon existing hot melt extrusion (HME) technology where the drug is dispersed in the polymer matrix. However, reliable manufacturing of drug-containing filaments remains a challenge along with the limitation of active ingredients which can sustain the processing risks involved in the HME process. To circumvent this obstacle, a single step FDM 3DP process was developed to manufacture thin-walled drug-free capsules which can be filled with dry or liquid drug product formulations. Drug release from these systems is governed by the combined dissolution of the FDM capsule 'shell' and the dosage form encapsulated in these shells. To prepare the shells, the 3D printer files (extension '.gcode') were modified by creating discrete zones, so-called 'zoning process', with individual print parameters. Capsules printed without the zoning process resulted in macroscopic print defects and holes. X-ray computed tomography, finite element analysis and mechanical testing were used to guide the zoning process and printing parameters in order to manufacture consistent and robust capsule shell geometries. Additionally, dose consistencies of drug containing liquid formulations were investigated in this work.
Assuntos
Cápsulas/química , Composição de Medicamentos/métodos , Impressão Tridimensional , Computadores , Liberação Controlada de Fármacos , Metformina/química , Poliésteres/química , Álcool de Polivinil/química , SoftwareRESUMO
This work establishes a predictive model that explicitly recognizes microstructural parameters in the description of the overall mass uptake and local gradients of moisture into tablets. Model equations were formulated based on local tablet geometry to describe the transient uptake of moisture. An analytical solution to a simplified set of model equations was solved to predict the overall mass uptake and moisture gradients with the tablets. The analytical solution takes into account individual diffusion mechanisms in different scales of porosity and diffusion into the solid phase. The time constant of mass uptake was found to be a function of several key material properties, such as tablet relative density, pore tortuosity, and equilibrium moisture content of the material. The predictions of the model are in excellent agreement with experimental results for microcrystalline cellulose tablets without the need for parameter fitting. The model presented provides a new method to analyze the transient uptake of moisture into hydrophilic materials with the knowledge of only a few fundamental material and microstructural parameters. In addition, the model allows for quick and insightful predictions of moisture diffusion for a variety of practical applications including pharmaceutical tablets, porous polymer systems, or cementitious materials.