Axial strength test for round flat faced versus capsule shaped bilayer tablets.

There has been increasing interest in fixed dose combination (FDC) therapy. Multi-layer tablets are a popular choice among various technologies to deliver FDCs. In most cases, round flat faced tooling is used in testing tablets as they have the simplest geometry. However, shaped tooling is more common for commercial products and may have an effect on bilayer tablet strength. Capsule shaped bilayer tablets, similar to a commercial image, and holders conforming to the tablet topology, were compared with similar round flat faced bilayer tablets and their corresponding holders. Bilayer tablets were subjected to an axial test device, until fracture and the quantitative breaking force value was recorded. As the second layer compression force increases, regardless of holder design, an increase in breaking force occurs as expected. This consistent trend provides insight regarding the breaking force of capsule shaped bilayer tablets. The results of this study show that at lower second layer compression forces, tablet geometry does not significantly impact the results. However, at higher compression forces, a significant difference in breaking force between tablet geometries exists. Therefore, using a test geometry close to the final commercial tablet image is recommended to have the most accurate prediction for tablet breakage.

Evaluation of the performance characteristics of bilayer tablets: Part II. Impact of environmental conditions on the strength of bilayer tablets.

Ambient air humidity and temperature are known to influence the mechanical strength of tablets. The objective of this work is to understand the influence of processing parameters and environmental conditions (humidity and temperature) on the strength of bilayer tablets. As part of this study, bilayer tablets were compressed with different layer ratios, dwell times, layer sequences, material properties (plastic and brittle), first and second layer forces, and lubricant concentrations. Compressed tablets were stored in stability chambers controlled at predetermined conditions (40C/45%RH, 40C/75%RH) for 1, 3, and 5 days. The axial strength of the stored tablets was measured and a statistical model was developed to determine the effects of the aforementioned factors on the strength of bilayer tablets. As part of this endeavor, a full 3 × 2(4) factorial design was executed. Responses of the experiments were analyzed using PROC GLM of SAS (SAS Institute Inc, Cary, North Carolina, USA). A model was fit using all the responses to determine the significant interactions (p < 0.05). Results of this study indicated that storage conditions and storage time have significant impact on the strength of bilayer tablets. For Avicel-lactose and lactose-Avicel tablets, tablet strength decreased with the increasing humidity and storage time. But for lactose-lactose tablets, due to the formation of solid bridges upon storage, an increase in tablet strength was observed. Significant interactions were observed between processing parameters and storage conditions on the strength of bilayer tablets.

Evaluation of the performance characteristics of bilayer tablets: Part I. Impact of material properties and process parameters on the strength of bilayer tablets.

Bilayer tableting technology has gained popularity in recent times, as bilayer tablets offer several advantages over conventional tablets. There is a dearth of knowledge on the impact of material properties and process conditions on the performance of bilayer tablets. This paper takes a statistical approach to develop a model that will determine the effect of the material properties and bilayer compression process parameters on the bonding strength and mode of breakage of bilayer tablets. Experiments were carried out at pilot scale to simulate the commercial manufacturing conditions. As part of this endeavor, a seven-factor half-fraction factorial (2(7-1)) design was executed to study the effect of bilayer tablet compression process factors on the bonding strength of bilayer tablets. Factors studied in this work include: material properties (plastic and brittle), layer ratio, dwell time, layer sequence, first- and second-layer forces, and lubricant concentration. Bilayer tablets manufactured in this study were tested using the axial tester, as it considers both the interfacial and individual layer bonding strengths. Responses of the experiments were analyzed using PROC GLM of SAS (SAS Institute Inc, Cary, North Carolina). A model was fit using all the responses to determine the significant interactions (p < 0.05). The results of this study indicated that nature of materials played a critical role on the strength of bilayer compacts and also on mode of fracture. Bilayer tablets made with brittle materials in both the layers are strongest, and fracture occurred in the first layer indicating that interface is stronger than layers. Significant interactions were observed between the selected factors and these results will provide an insight into the interplay of material properties, process parameters, and lubricant concentration on the bonding strength and mode of breakage of bilayer tablets.

Review of bilayer tablet technology.

Therapeutic strategies based on oral delivery of bilayer (and multilayer) tablets are gaining more acceptance among brand and generic products due to a confluence of factors including advanced delivery strategies, patient compliance and combination therapy. Successful manufacturing of these ever more complex systems needs to overcome a series of challenges from formulation design to tablet press monitoring and control. This article provides an overview of the state-of-the-art of bilayer tablet technology, highlighting the main benefits of this type of oral dosage forms while providing a description of current challenges and advances toward improving manufacturing practices and product quality. Several aspects relevant to bilayer tablet manufacturing are addressed including material properties, lubrication, layer ordering, layer thickness, layer weight control, as well as first and final compression forces. A section is also devoted to bilayer tablet characterization that present additional complexities associated with interfaces between layers. The available features of the manufacturing equipment for bilayer tablet production are also described indicating the different strategies for sensing and controls offered by bilayer tablet press manufacturers. Finally, a roadmap for bilayer tablet manufacturing is advanced as a guideline to formulation design and selection of process parameters and equipment.

Influence of compaction properties and interfacial topography on the performance of bilayer tablets.

Bilayer tablets are generating great interest recently as they can achieve controlled delivery of different drugs with pre-defined release profiles. However, the production of such tablets has been facing great challenges as the layered tablets are prone to delaminate or fracture in the individual layers due to insufficient bonding strength of layers and adhesion at the interfaces. This paper will provide an insight into the role of interfacial topography on the performance of the bilayer tablets. In this study, two widely used pharmaceutical excipients: microcrystalline cellulose and lactose were investigated. Bilayer tablets were manufactured with a range of first and second layer compression forces. A crack of known dimensions was introduced at the interface to investigate the crack propagation mechanisms upon axially loading the bilayer tablet, and to determine the stress intensity factor (K(I)) of the interface (will be discussed in a separate paper). The results indicated that a strong dependency of the strength of bilayer tablets and mode of crack propagation on the material and compaction properties. The results showed that the strength of bilayer tablets increased with the increase of interfacial roughness, and the first layer and second layer forces determined the magnitude of interfacial roughness for both plastic and brittle materials. Further, the results also indicated that layer sequence and compaction forces played a key role in influencing the strength of the bilayer tablets. For the same (first and second layer) force combination, interfacial strength is higher for the tablets made of brittle material in the first layer. It was observed that interfacial strength decreased with the increase of lubricant concentration. The studies showed that the effect of lubricant (i.e. reduction in compact strength with the increase of lubricant concentration) on the strength of compacts is higher for tablets made of plastic material as compared to the tablets made of brittle material.