Highly efficient electrocatalytic CO2 reduction by a CrIII quaterpyridine complex.

Design tactics and mechanistic studies both remain as fundamental challenges during the exploitations of earth-abundant molecular electrocatalysts for CO2 reduction, especially for the rarely studied Cr-based ones. Herein, a quaterpyridyl CrIII catalyst is found to be highly active for CO2 electroreduction to CO with 99.8% Faradaic efficiency in DMF/phenol medium. A nearly one order of magnitude higher turnover frequency (86.6 s-1) over the documented Cr-based catalysts (<10 s-1) can be achieved at an applied overpotential of only 190 mV which is generally 300 mV lower than these precedents. Such a high performance at this low driving force originates from the metal-ligand cooperativity that stabilizes the low-valent intermediates and serves as an efficient electron reservoir. Moreover, a synergy of electrochemistry, spectroelectrochemistry, electron paramagnetic resonance, and quantum chemical calculations allows to characterize the key CrII, CrI, Cr0, and CO-bound Cr0 intermediates as well as to verify the catalytic mechanism.

Boosting CO2 photoreduction by π-π-induced preassembly between a Cu(I) sensitizer and a pyrene-appended Co(II) catalyst.

The design of a highly efficient system for CO2 photoreduction fully based on earth-abundant elements presents a challenge, which may be overcome by installing suitable interactions between photosensitizer and catalyst to expedite the intermolecular electron transfer. Herein, we have designed a pyrene-decorated Cu(I) complex with a rare dual emission behavior, aiming at additional π-interaction with a pyrene-appended Co(II) catalyst for visible light-driven CO2-to-CO conversion. The results of 1H NMR titration, time-resolved fluorescence/absorption spectroscopies, quantum chemical simulations, and photocatalytic experiments clearly demonstrate that the dynamic π-π interaction between sensitizer and catalyst is highly advantageous in photocatalysis by accelerating the intermolecular electron transfer rate up to 6.9 × 105 s-1, thus achieving a notable apparent quantum yield of 19% at 425 nm with near-unity selectivity. While comparable to most earth-abundant molecular systems, this value is over three times of the pyrene-free system (6.0%) and far surpassing the benchmarking Ru(II) tris(bipyridine) (0.3%) and Ir(III) tris(2-phenylpyridine) (1.4%) photosensitizers under parallel conditions.

Controlling the Photophysical Properties of a Series of Isostructural d6 Complexes Based on Cr0, MnI, and FeII.

Development of first-row transition metal complexes with similar luminescence and photoredox properties as widely used RuII polypyridines is attractive because metals from the first transition series are comparatively abundant and inexpensive. The weaker ligand field experienced by the valence d-electrons of first-row transition metals challenges the installation of the same types of metal-to-ligand charge transfer (MLCT) excited states as in precious metal complexes, due to rapid population of energetically lower-lying metal-centered (MC) states. In a family of isostructural tris(diisocyanide) complexes of the 3d6 metals Cr0, MnI, and FeII, the increasing effective nuclear charge and ligand field strength allow us to control the energetic order between the 3MLCT and 3MC states, whereas pyrene decoration of the isocyanide ligand framework provides control over intraligand (ILPyr) states. The chromium(0) complex shows red 3MLCT phosphorescence because all other excited states are higher in energy. In the manganese(I) complex, a microsecond-lived dark 3ILPyr state, reminiscent of the types of electronic states encountered in many polyaromatic hydrocarbon compounds, is the lowest and becomes photoactive. In the iron(II) complex, the lowest MLCT state has shifted to so much higher energy that 1ILPyr fluorescence occurs, in parallel to other excited-state deactivation pathways. Our combined synthetic-spectroscopic-theoretical study provides unprecedented insights into how effective nuclear charge, ligand field strength, and ligand π-conjugation affect the energetic order between MLCT and ligand-based excited states, and under what circumstances these individual states become luminescent and exploitable in photochemistry. Such insights are the key to further developments of luminescent and photoredox-active first-row transition metal complexes.

Reversible Photoinduced Ligand Substitution in a Luminescent Chromium(0) Complex.

Light-triggered dissociation of ligands forms the basis for many compounds of interest for photoactivated chemotherapy (PACT), in which medicinally active substances are released or "uncaged" from metal complexes upon illumination. Photoinduced ligand dissociation is usually irreversible, and many recent studies performed in the context of PACT focused on ruthenium(II) polypyridines and related heavy metal complexes. Herein, we report a first-row transition metal complex, in which photoinduced dissociation and spontaneous recoordination of a ligand unit occurs. Two scorpionate-type tridentate chelates provide an overall six-coordinate arylisocyanide environment for chromium(0). Photoexcitation causes decoordination of one of these six ligating units and coordination of a solvent molecule, at least in tetrahydrofuran and 1,4-dioxane solvents, but far less in toluene, and below detection limit in cyclohexane. Transient UV-vis absorption spectroscopy and quantum chemical simulations point to photoinduced ligand dissociation directly from an excited metal-to-ligand charge-transfer state. Owing to the tridentate chelate design and the substitution lability of the first-row transition metal, recoordination of the photodissociated arylisocyanide ligand unit can occur spontaneously on a millisecond time scale. This work provides insight into possible self-healing mechanisms counteracting unwanted photodegradation processes and seems furthermore relevant in the contexts of photoswitching and (photo)chemical information storage.

Mechanism of Plasmon-Induced Catalysis of Thiolates and the Impact of Reaction Conditions.

The conversion of the thiols 4-aminothiophenol (ATP) and 4-nitrothiophenol (NTP) can be considered as one of the standard reactions of plasmon-induced catalysis and thus has already been the subject of numerous studies. Currently, two reaction pathways are discussed: one describes a dimerization of the starting material yielding 4,4'-dimercaptoazobenzene (DMAB), while in the second pathway, it is proposed that NTP is reduced to ATP in HCl solution. In this combined experimental and theoretical study, we disentangled the involved plasmon-mediated reaction mechanisms by carefully controlling the reaction conditions in acidic solutions and vapor. Motivated by the different surface-enhanced Raman scattering (SERS) spectra of NTP/ATP samples and band shifts in acidic solution, which are generally attributed to water, additional experiments under pure gaseous conditions were performed. Under such acidic vapor conditions, the Raman data strongly suggest the formation of a hitherto not experimentally identified stable compound. Computational modeling of the plasmonic hybrid systems, i.e., regarding the wavelength-dependent character of the involved electronic transitions of the detected key intermediates in both reaction pathways, confirmed the experimental finding of the new compound, namely, 4-nitrosothiophenol (TP*). Tracking the reaction dynamics via time-dependent SERS measurements allowed us to establish the link between the dimer- and monomer-based pathways and to suggest possible reaction routes under different environmental conditions. Thereby, insight at the molecular level was provided with respect to the thermodynamics of the underlying reaction mechanism, complementing the spectroscopic results.

Beyond the First Coordination Sphere─Manipulating the Excited-State Landscape in Iron(II) Chromophores with Protons.

Molecular transition metal chromophores play a central role in light harvesting and energy conversion. Recently, earth-abundant transition-metal-based chromophores have begun to challenge the dominance of platinum group metal complexes in this area. However, the development of new chromophores with optimized photophysical properties is still limited by a lack of synthetic methods, especially with respect to heteroleptic complexes with functional ligands. Here, we demonstrate a facile and efficient method for the combination of strong-field carbenes with the functional 2,2'-bibenzimidazole ligand in a heteroleptic iron(II) chromophore complex. Our approach yields two isomers that differ predominantly in their excited-state lifetimes based on the symmetry of the ligand field. Deprotonation of both isomers leads to a significant red-shift of the metal-to-ligand charge transfer (MLCT) absorption and a shortening of excited-state lifetimes. Femtosecond transient absorption spectroscopy in combination with quantum chemical simulations and resonance Raman spectroscopy reveals the complex relationship between protonation and photophysical properties. Protonation is found to tip the balance between MLCT and metal-centered (MC) excited states in favor of the former. This study showcases the first example of fine-tuning of the excited-state landscape in an iron(II) chromophore through second-sphere manipulations and provides a new perspective to the challenge of excited-state optimizations in 3d transition metal chromophores.

Oxidation-state sensitive light-induced dynamics of Ruthenium-4H-Imidazole complexes.

Oxidized molecular states are key intermediates in photo-induced redox reactions, e. g., intermolecular charge transfer between photosensitizer and catalyst in photoredox catalysis. The stability and longevity of the oxidized photosensitizer is an important factor in optimizing the respective light-driven reaction pathways. In this work the oxidized states of ruthenium(II)-4H-imidazole dyes are studied. The ruthenium complexes constitute benchmark photosensitizers in solar energy interconversion processes with exceptional chemical stability, strong visible light absorption, and favourable redox properties. To rationalize the light-induced reaction in the oxidized ruthenium(III) systems, we combine UV-vis absorption, resonance Raman, and transient absorption spectroelectrochemistry (SEC) with time-dependent density functional theory (TDDFT) calculations. Three complexes are compared, which vary with respect to their coordination environment, i. e., combining an 4H-imidazole with either 2,2'-bipyridine (bpy) or 2,2';6'2"-terpyridine (tpy) coligands, and chloride or isothiocyanate ligands. While all oxidized complexes have similar steady state absorption properties, their excited state kinetics differ significantly; the study thus opens the doorway to study the light-driven reactivity of oxidized molecular intermediates in intermolecular charge transfer cascades.

Light-Induced Charge Separation in Covalently Linked BODIPY-Quinone-Alkyne Dyads.

Visible light-induced charge separation and directional charge transfer are cornerstones for artificial photosynthesis and the generation of solar fuels. Here, we report synthetic access to a series of noble metal-free donor-acceptor dyads based on bodipy light-absorbers and redox-active quinone/anthraquinone charge storage sites. Peripheral functionalization of the quinone/anthraquinone units with alkynes primes the dyads for integration into a range of light-harvesting systems, e. g., by Cu-catalyzed cycloadditions (CLICK chemistry) or Pd-catalyzed C-C cross-coupling reactions. Initial photophysical, electrochemical and theoretical analyses reveal the principal processes during the light-induced charge separation in the reported dyads.

Controlling Excited State Localization in Bichromophoric Photosensitizers via the Bridging Group.

A series of photosensitizers comprised of both an inorganic and an organic chromophore are investigated in a joint synthetic, spectroscopic, and theoretical study. This bichromophoric design strategy provides a means by which to significantly increase the excited state lifetime by isolating the excited state away from the metal center following intersystem crossing. A variable bridging group is incorporated between the donor and acceptor units of the organic chromophore, and its influence on the excited state properties is explored. The Franck-Condon (FC) photophysics and subsequent excited state relaxation pathways are investigated with a suite of steady-state and time-resolved spectroscopic techniques in combination with scalar-relativistic quantum chemical calculations. It is demonstrated that the presence of an electronically conducting bridge that facilitates donor-acceptor communication is vital to generate long-lived (32 to 45 µs), charge-separated states with organic character. In contrast, when an insulating 1,2,3-triazole bridge is used, the excited state properties are dominated by the inorganic chromophore, with a notably shorter lifetime of 60 ns. This method of extending the lifetime of a molecular photosensitizer is, therefore, of interest for a range of molecular electronic devices and photophysical applications.

Homoleptic Al(III) Photosensitizers for Durable CO2 Photoreduction.

Exploiting noble-metal-free systems for high-performance photocatalytic CO2 reduction still presents a key challenge, partially due to the long-standing difficulties in developing potent and durable earth-abundant photosensitizers. Therefore, based on the very cheap aluminum metal, we have deployed a systematic series of homoleptic Al(III) photosensitizers featuring 2-pyridylpyrrolide ligands for CO2 photoreduction. The combined studies of steady-state and time-resolved spectroscopy as well as quantum chemical calculations demonstrate that in anerobic CH3CN solutions at room temperature, visible-light excitation of the Al(III) photosensitizers leads to an efficient population of singlet excited states with nanosecond-scale lifetimes and notable emission quantum yields (10-40%). The results of transient absorption spectroscopy further identified the presence of emissive singlet and unexpectedly nonemissive triplet excited states. More importantly, the introduction of methyl groups at the pyrrolide rings can greatly improve the visible-light absorption, reducing power, and durability of the Al(III) photosensitizers. With triethanolamine, BIH (1,3-dimethyl-2-phenyl-2,3-dihydro-1H-benzo[d]imidazole), and an Fe(II)-quaterpyridine catalyst, the most methylated Al(III) photosensitizer achieves an apparent quantum efficiency of 2.8% at 450 nm for selective (>99%) CO2-to-CO conversion, which is nearly 28 times that of the unmethylated one (0.1%) under identical conditions. The optimal system realizes a maximum turnover number of 10250 and higher robustness than the systems with Ru(II) and Cu(I) benchmark photosensitizers. Quenching experiments using fluorescence spectroscopy elucidate that the photoinduced electron transfer in the Al(III)-sensitized system follows a reductive quenching pathway. The remarkable tunability and cost efficiency of these Al(III) photosensitizers should allow them as promising components in noble-metal-free systems for solar fuel conversion.

Stability of Catalytic Centres in Light-Driven Hydrogen Evolution by Di- and Oligonuclear Photocatalysts.

A review. In recent decades, mimicking natural photosynthesis by artificial photocatalysis represented a major research direction with the ultimate goal of reducing fossil fuel consumption through efficient solar energy harvesting. To transfer molecular photocatalysis from the lab scale to an industrially relevant process, it is important to overcome instability problems of the catalysts during light-driven operation. As it is well-known that many of the typically utilized noble metal-based catalytic centres (e. g. Pt and Pd) undergo particle formation during (photo)catalysis and thus switch the whole process from a homogeneous into a heterogeneous one, an understanding of the factors governing particle formation is crucially needed. The review therefore focuses on di- and oligonuclear photocatalysts bearing a range of different bridging ligand architectures for drawing structure-catalyst-stability relationships in light-driven intramolecular reductive catalysis. In addition, ligand effects at the catalytic centre and their implications for catalytic activity in intermolecular systems will be discussed, as will important insights into the future design of operationally stable catalysts.

The three kingdoms-Photoinduced electron transfer cascades controlled by electronic couplings.

Excited states are the key species in photocatalysis, while the critical parameters that govern their applications are (i) excitation energy, (ii) accessibility, and (iii) lifetime. However, in molecular transition metal-based photosensitizers, there is a design tension between the creation of long-lived excited (triplet), e.g., metal-to-ligand charge transfer (3MLCT) states and the population of such states. Long-lived triplet states have low spin-orbit coupling (SOC) and hence their population is low. Thus, a long-lived triplet state can be populated but inefficiently. If the SOC is increased, the triplet state population efficiency is improved-coming at the cost of decreasing the lifetime. A promising strategy to isolate the triplet excited state away from the metal after intersystem crossing (ISC) involves the combination of transition metal complex and an organic donor/acceptor group. Here, we elucidate the excited state branching processes in a series of Ru(II)-terpyridyl push-pull triads by quantum chemical simulations. Scalar-relativistic time-dependent density theory simulations reveal that efficient ISC takes place along 1/3MLCT gateway states. Subsequently, competitive electron transfer (ET) pathways involving the organic chromophore, i.e., 10-methylphenothiazinyl and the terpyridyl ligands are available. The kinetics of the underlying ET processes were investigated within the semiclassical Marcus picture and along efficient internal reaction coordinates that connect the respective photoredox intermediates. The key parameter that governs the population transfer away from the metal toward the organic chromophore either by means of ligand-to-ligand (3LLCT; weakly coupled) or intra-ligand charge transfer (3ILCT; strongly coupled) states was determined to be the magnitude of the involved electronic coupling.

Solid-to-Liposome Conformational Transition of Phosphatidylcholine and Phosphatidylserine Probed by Atomic Force Microscopy, Infrared Spectroscopy, and Density Functional Theory Calculations.

Liposomes are emerging therapeutic formulations for site-specific delivery of chemotherapeutic drugs. The efficiency and selectivity of drug delivery by these carriers largely rely on their surface properties, shape, and size. There is a growing demand for analytical approaches that can be used for structural and morphological characterization of liposomes at the single-vesicle level. AFM-IR is a modern optical nanoscopic technique that combines the advantages of scanning probe microscopy and infrared spectroscopy. Our findings show that AFM-IR can be used to probe conformational changes in phospholipids that take place upon their assembly into liposomes. Such conclusions can be made based on the corresponding changes in intensities of the lipid vibrational bands as the molecules transition from a solid state into large unilamellar vesicles (LUVs). This spectroscopic analysis of LUV formation together with density functional theory calculations also reveals the extent to which the molecular conformation and local environment of the functional groups alter the AFM-IR spectra of phospholipids. Using melittin as a test protein, we also examined the extent to which LUVs can be used for protein internalization. We found that melittin enters LUVs nearly instantaneously, which protects it from possible structural modifications that are caused by a changing environment. This foundational work empowers AFM-IR analysis of liposomes and opens new avenues for determination of the molecular mechanisms of liposome-drug interactions.

A Combined Spectroscopic and Theoretical Study on a Ruthenium Complex Featuring a π-Extended dppz Ligand for Light-Driven Accumulation of Multiple Reducing Equivalents.

The design of photoactive systems capable of storing and relaying multiple electrons is highly demanded in the field of artificial photosynthesis, where transformations of interest rely on multielectronic redox processes. The photophysical properties of the ruthenium photosensitizer [(bpy)2 Ru(oxim-dppqp)]2+ (Ru), storing two electrons coupled to two protons on the π-extended oxim-dppqp ligand under light-driven conditions, are investigated by means of excitation wavelength-dependent resonance Raman and transient absorption spectroscopies, in combination with time-dependent density functional theory; the results are discussed in comparison to the parent [(bpy)2 Ru(dppz)]2+ and [(bpy)2 Ru(oxo-dppqp)]2+ complexes. In addition, this study provides in-depth insights on the impact of protonation or of accumulation of multiple reducing equivalents on the reactive excited states.

Pyrimidoquinazolinophenanthroline Opens Next Chapter in Design of Bridging Ligands for Artificial Photosynthesis.

The synthesis and detailed characterization of a new Ru polypyridine complex containing a heteroditopic bridging ligand with previously unexplored metal-metal distances is presented. Due to the twisted geometry of the novel ligand, the resultant division of the ligand in two distinct subunits leads to steady state as well as excited state properties of the corresponding mononuclear Ru(II) polypyridine complex resembling those of prototype [Ru(bpy)3 ]2+ (bpy=2,2'-bipyridine). The localization of the initially optically excited and the nature of the long-lived excited states on the Ru-facing ligand spheres is evaluated by resonance Raman and fs-TA spectroscopy, respectively, and supported by DFT and TDDFT calculations. Coordination of a second metal (Zn or Rh) to the available bis-pyrimidyl-like coordination sphere strongly influences the frontier orbitals, apparent by, for example, luminescence quenching. Thus, the new bridging ligand motif offers electronic properties, which can be adjusted by the nature of the second metal center. Using the heterodinuclear Ru-Rh complex, visible light-driven reduction of NAD+ to NADH was achieved, highlighting the potential of this system for photocatalytic applications.

A Highly Fluorescent Dinuclear Aluminium Complex with Near-Unity Quantum Yield.

The high natural abundance of aluminium makes the respective fluorophores attractive for various optical applications, but photoluminescence quantum yields above 0.7 have yet not been reported for solutions of aluminium complexes. In this contribution, a dinuclear aluminium(III) complex featuring enhanced photoluminescence properties is described. Its facile one-pot synthesis originates from a readily available precursor and trimethyl aluminium. In solution, the complex exhibits an unprecedented photoluminescence quantum yield near unity (Φabsolute 1.0±0.1) and an excited-state lifetime of 2.3 ns. In the solid state, J-aggregation and aggregation-caused quenching are noted, but still quantum yields of 0.6 are observed. Embedding the complex in electrospun non-woven fabrics yields a highly fluorescent fleece possessing a quantum yield of 0.9±0.04.

Activating a [FeFe] Hydrogenase Mimic for Hydrogen Evolution under Visible Light.

Inspired by the active center of the natural [FeFe] hydrogenases, we designed a compact and precious metal-free photosensitizer-catalyst dyad (PS-CAT) for photocatalytic hydrogen evolution under visible light irradiation. PS-CAT represents a prototype dyad comprising π-conjugated oligothiophenes as light absorbers. PS-CAT and its interaction with the sacrificial donor 1,3-dimethyl-2-phenylbenzimidazoline were studied by steady-state and time-resolved spectroscopy coupled with electrochemical techniques and visible light-driven photocatalytic investigations. Operando EPR spectroscopy revealed the formation of an active [FeI Fe0 ] species-in accordance with theoretical calculations-presumably driving photocatalysis effectively (TON≈210).

Excited-State Switching in Rhenium(I) Bipyridyl Complexes with Donor-Donor and Donor-Acceptor Substituents.

The optical properties of two Re(CO)3(bpy)Cl complexes in which the bpy is substituted with two donor (triphenylamine, TPA, ReTPA2) as well as both donor (TPA) and acceptor (benzothiadiazole, BTD, ReTPA-BTD) groups are presented. For ReTPA2 the absorption spectra show intense intraligand charge-transfer (ILCT) bands at 460 nm with small solvatochromic behavior; for ReTPA-BTD the ILCT transitions are weaker. These transitions are assigned as TPA → bpy transitions as supported by resonance Raman data and TDDFT calculations. The excited-state spectroscopy shows the presence of two emissive states for both complexes. The intensity of these emission signals is modulated by solvent. Time-resolved infrared spectroscopy definitively assigns the excited states present in CH2Cl2 to be MLCT in nature, and in MeCN the excited states are ILCT in nature. DFT calculations indicated this switching with solvent is governed by access to states controlled by spin-orbit coupling, which is sufficiently different in the two solvents, allowing to select out each of the charge-transfer states.

Tuning the metal-ligand bond in the σ-complexes of stannylenes and azabenzenes.

The metal-ligand bond in a set of 60 σ-complexes has been investigated by electronic structure computations. These σ-complexes originate from the unique combination of 12 stannylenes (SnX2 ) with five azabenzene ligands (pyridine, pyrazine, pyrimidine, pyridazine, and s-triazine), where the nitrogen center of the ligand acts as σ-donor and the tin(II) center as σ-acceptor in a 1:1 fashion. The Sn ← N bond and the total interaction between the stannylene and azabenzene moieties of the σ-complexes are characterized in depth to relate the Sn ← N strength to the substitution pattern at SnX2 and to the number and the positioning of N atoms in the azabenzenes. Such X substituents as (iso)cyano and trifluoromethyl groups enhance the interaction strength, while the presence of alkyl, phenyl, and silyl substituents in SnX2 diminishes the stability of σ-complexes. A gradual weakening of the total interaction is associated with the growing number of N atoms in the azabenzenes, while the N-atom positioning in pyridazine is particularly effective in strengthening the interaction with stannylenes. Variations in the Sn ← N bond strength usually follow those in the total interaction between the moieties but the interacting quantum atoms picture of Sn ← N reveals certain intriguing exceptions.

Coupling of photoactive transition metal complexes to a functional polymer matrix*.

Conductive polymers represent a promising alternative to semiconducting oxide electrodes typically used in dye-sensitized cathodes as they more easily allow a tuning of the physicochemical properties. This can then also be very beneficial for using them in light-driven catalysis. In this computational study, we address the coupling of Ru-based photosensitizers to a polymer matrix by combining two different first-principles electronic structure approaches. We use a periodic density functional theory code to properly account for the delocalized nature of the electronic states in the polymer. These ground state investigations are complemented by time-dependent density functional theory simulations to assess the Franck-Condon photophysics of the present photoactive hybrid material based on a molecular model system. Our results are consistent with recent experimental observations and allow to elucidate the light-driven redox chemical processes - eventually leading to charge separation - in the present functional hybrid systems with potential application as photocathode materials.