RESUMO
BACKGROUND: Simultaneous positron emission tomography (PET)/magnetic resonance imaging (MRI) scanners and inserts are valuable tools for accurate diagnosis, treatment planning, and monitoring due to their complementary information. However, the integration of a PET system into an MRI scanner presents technical challenges for a distortion-free operation. PURPOSE: We aim to develop a PET insert dedicated to breast imaging in combination with the 3T PET/MRI scanner Biograph mMR (Siemens Healthineers) as well as a brain PET insert for the 7T MRI scanner MAGNETOM Terra (Siemens Healthineers). For this development, we selected as a basis the C13500 series PET modules (Hamamatsu Photonics K.K.) as they offer an all-in-one solution with a scalable, modular design for compact integration with state-of-the-art performance. The original PET modules were not designed to be operated with an MRI scanner, therefore we implemented several modifications such as signal transmission via plastic optical fiber, radio frequency (RF) shielding of the front-end electronics, and filter for the power supply lines. In this work, we evaluated the mutual MRI compatibility between the modified PET modules and the 3T and 7T MRI scanner. METHODS: We used a proof-of-concept setup with two detectors to comprehensively evaluate a potential distortion of the performance of the modified PET modules whilst exposing them to a variety of MR sequences up to the peak operation conditions of the Biograph mMR. A method using the periodicity of the sequences to identify distortions of the PET events in the phase of RF pulse transmission was introduced. Vice versa, the potential distortion of the Biograph mMR was evaluated by vendor proprietary MRI compatibility test sequences. Afterwards, these studies were extended to the MAGNETOM Terra. RESULTS: No distortions were introduced by gradient field switching (field strength up to 20 mT/m at a slew rate of 66.0 T/ms-1 ). However, RF pulse transmission induced a reduction of the single event rate from 33.0 kcounts/s to 32.0 kcounts/s and a degradation of the coincidence resolution time from 251 to 299 ps. Further, the proposed method revealed artifacts in the energy and timing histograms. Finally, by using the front-end filters it was possible to prevent any RF pulse induced distortion of event rate, energy, or time stamps even for a 700° flip angle (45.5 µT) sequence. The evaluations to assess potential distortions of the MRI scanner showed that carefully designed RF shielding boxes for the PET modules were required to prevent distortion of the RF spectra. The increase in B0 field inhomogeneity of 0.254 ppm and local changes of the B1 field of 12.5% introduced by the PET modules did not qualitatively affect the MR imaging with a spin echo and MPRAGE sequence for the Biograph mMR and the MAGNETOM Terra, respectively. CONCLUSION: Our study demonstrates the feasibility of using a modified version of the PET modules in combination with 3T and 7T MRI scanners. Building upon the encouraging MRI compatibility results from our proof-of-concept detectors, we will proceed to develop PET inserts for breast and brain imaging using these modules.
Assuntos
Imageamento por Ressonância Magnética , Tomografia por Emissão de Pósitrons , Imagens de Fantasmas , Imageamento por Ressonância Magnética/métodos , Tomografia por Emissão de Pósitrons/métodos , Encéfalo , Ondas de RádioRESUMO
In whole-body MR/PET, the human attenuation correction can be based on the MR data. However, an MR-based field-of-view (FoV) is limited due to physical restrictions such as B0 inhomogeneities and gradient nonlinearities. Therefore, for large patients, the MR image and the attenuation map might be truncated and the attenuation correction might be biased. The aim of this work is to explore extending the MR FoV through B0 homogenization using gradient enhancement in which an optimal readout gradient field is determined to locally compensate B0 inhomogeneities and gradient nonlinearities. A spin-echo-based sequence was developed that computes an optimal gradient for certain regions of interest, for example, the patient's arms. A significant distortion reduction was achieved outside the normal MR-based FoV. This FoV extension was achieved without any hardware modifications. In-plane distortions in a transaxially extended FoV of up to 600 mm were analyzed in phantom studies. In vivo measurements of the patient's arms lying outside the normal specified FoV were compared with and without the use of B0 homogenization using gradient enhancement. In summary, we designed a sequence that provides data for reducing the image distortions due to B0 inhomogeneities and gradient nonlinearities and used the data to extend the MR FoV.
Assuntos
Aumento da Imagem/métodos , Interpretação de Imagem Assistida por Computador/métodos , Imageamento Tridimensional/métodos , Imageamento por Ressonância Magnética/métodos , Imagem Multimodal/métodos , Tomografia por Emissão de Pósitrons/métodos , Imagem Corporal Total/métodos , Algoritmos , Humanos , Reprodutibilidade dos Testes , Sensibilidade e EspecificidadeRESUMO
OBJECTIVES: Technical performance evaluation of a human brain PET/MRI system. METHODS: The magnetic field compatible positron emission tomography (PET) insert is based on avalanche photodiode (APD) arrays coupled with lutetium oxyorthosilicate (LSO) crystals and slip-fits into a slightly modified clinical 3-T MRI system. The mutual interference between the two imaging techniques was minimised by the careful design of the hardware to maintain the quality of the B (0) and B (1) field homogeneity. RESULTS: The signal-to-noise ratio (SNR) and the homogeneity of the MR images were minimally influenced by the presence of the PET. Measurements according to the Function Biomedical Informatics Research Network (FBIRN) protocol proved the combined system's ability to perform functional MRI (fMRI). The performance of the PET insert was evaluated according to the National Electrical Manufacturers Association (NEMA) standard. The noise equivalent count rate (NEC) peaked at 30.7 × 10(3) counts/s at 7.3 kBq/mL. The point source sensitivity was greater than 7 %. The spatial resolution in the centre field of view was less than 3 mm. Patient data sets clearly revealed a noticeably good PET and MR image quality. CONCLUSION: PET and MRI phantom tests and first patient data exhibit the device's potential for simultaneous multiparametric imaging. KEY POINTS: ⢠Combination of PET and MRI is a new emerging imaging technology. ⢠Evaluated brain PET/MRI enables uncompromised imaging performance. ⢠PET/MRI aims to provide multiparametric imaging allowing acquisition of morphology and metabolism.
Assuntos
Encéfalo/patologia , Imageamento por Ressonância Magnética/métodos , Tomografia por Emissão de Pósitrons/métodos , Mapeamento Encefálico/métodos , Desenho de Equipamento , Humanos , Processamento de Imagem Assistida por Computador/métodos , Lutécio/farmacologia , Imageamento por Ressonância Magnética/instrumentação , Imagens de Fantasmas , Tomografia por Emissão de Pósitrons/instrumentação , Reprodutibilidade dos Testes , Razão Sinal-Ruído , Silicatos/farmacologiaRESUMO
The combination of MR and PET scanners can provide a powerful tool for clinical diagnosis and investigation. Among the existing approaches, the most challenging is that of complete hardware integration of both scanners. Such an integrated tomograph would allow simultaneous acquisition of both modalities, which could help solve issues such as cardiac and respiratory motion. Full integration imposes restrictions on the design of the PET part, such as detector configuration and maximum ring diameter. Furthermore, MR components surrounding the PET detector ring may cause gamma ray interactions, thus affecting PET performance. The purpose of this article is to assess the performance of a hypothetical whole-body integrated MR/PET scanner using Monte Carlo simulation techniques and compare it to state-of-the-art PET/CT devices used in clinical routine. The Monte Carlo simulation toolkit used for this study is the GEANT4 application for emission tomography. A hypothetical whole-body MR/PET tomograph fully integrated at hardware level and positioned between gradient and local coils of the MR scanner has been modeled. The NEMA 2-2001 protocol has been used to configure the simulations in order to measure sensitivity, scatter fraction, count losses, and random detections. Global sensitivity values as a function of the lower-level discriminator (LLD) energy are provided for time resolutions of 5 and 2.25 ns. In addition, the scatter fraction of the system is studied as a function of the LLD for energy resolution values of 10%, 15%, and 20%. Finally, true, scatter, random, and noise equivalent count rate curves as a function of activity concentration are given for dead-time values of 136, 432, and 1150 ns and for time resolution values of 2.25 and 5 ns. The influence on the count rate performance of the integrated PET scanner of the new geometry and interfering MR elements has been measured. The results show that the interference of the MR components has a much lower impact than the reduction in the detector ring diameter. Due to the larger solid angle coverage, the sensitivity is higher than that measured for a clinical PET/CT system (6200-10 900 cps/MBq at the center of the scanner) but not enough to compensate the degradation of the noise equivalent count rate due to increased scatter detection. The simulations prove the viability of an integrated MR/PET system and suggest that priority has to be given to either the improvement of the temporal resolution or the correction of triple coincidences if competitive performance is to be achieved.
Assuntos
Simulação por Computador , Imageamento por Ressonância Magnética/instrumentação , Método de Monte Carlo , Tomografia por Emissão de Pósitrons/instrumentação , Desenho de Equipamento , Modelos Teóricos , Imagens de Fantasmas , Probabilidade , Espalhamento de Radiação , Sensibilidade e Especificidade , Tomógrafos ComputadorizadosRESUMO
The purpose of this study was to apply a magnetic resonance (MR) imaging-compatible positron emission tomographic (PET) detector technology for simultaneous MR/PET imaging of the human brain and skull base. The PET detector ring consists of lutetium oxyorthosilicate (LSO) scintillation crystals in combination with avalanche photodiodes (APDs) mounted in a clinical 3-T MR imager with use of the birdcage transmit/receive head coil. Following phantom studies, two patients were simultaneously examined by using fluorine 18 fluorodeoxyglucose (FDG) PET and MR imaging and spectroscopy. MR/PET data enabled accurate coregistration of morphologic and multifunctional information. Simultaneous MR/PET imaging is feasible in humans, opening up new possibilities for the emerging field of molecular imaging.
Assuntos
Encéfalo/diagnóstico por imagem , Encéfalo/patologia , Fluordesoxiglucose F18 , Imageamento por Ressonância Magnética/métodos , Técnica de Subtração , Estudos de Viabilidade , Humanos , Radiografia , Compostos Radiofarmacêuticos , Reprodutibilidade dos Testes , Sensibilidade e EspecificidadeRESUMO
PURPOSE: In quantitative PET imaging, it is critical to accurately measure and compensate for the attenuation of the photons absorbed in the tissue. While in PET/CT the linear attenuation coefficients can be easily determined from a low-dose CT-based transmission scan, in whole-body MR/PET the computation of the linear attenuation coefficients is based on the MR data. However, a constraint of the MR-based attenuation correction (AC) is the MR-inherent field-of-view (FoV) limitation due to static magnetic field (B0) inhomogeneities and gradient nonlinearities. Therefore, the MR-based human AC map may be truncated or geometrically distorted toward the edges of the FoV and, consequently, the PET reconstruction with MR-based AC may be biased. This is especially of impact laterally where the patient arms rest beside the body and are not fully considered. METHODS: A method is proposed to extend the MR FoV by determining an optimal readout gradient field which locally compensates B0 inhomogeneities and gradient nonlinearities. This technique was used to reduce truncation in AC maps of 12 patients, and the impact on the PET quantification was analyzed and compared to truncated data without applying the FoV extension and additionally to an established approach of PET-based FoV extension. RESULTS: The truncation artifacts in the MR-based AC maps were successfully reduced in all patients, and the mean body volume was thereby increased by 5.4%. In some cases large patient-dependent changes in SUV of up to 30% were observed in individual lesions when compared to the standard truncated attenuation map. CONCLUSIONS: The proposed technique successfully extends the MR FoV in MR-based attenuation correction and shows an improvement of PET quantification in whole-body MR/PET hybrid imaging. In comparison to the PET-based completion of the truncated body contour, the proposed method is also applicable to specialized PET tracers with little uptake in the arms and might reduce the computation time by obviating the need for iterative calculations of the PET emission data beyond those required for reconstructing images.
Assuntos
Processamento de Imagem Assistida por Computador/métodos , Imageamento por Ressonância Magnética/métodos , Imagem Multimodal/métodos , Tomografia por Emissão de Pósitrons/métodos , Feminino , Fluordesoxiglucose F18 , Humanos , Masculino , Fatores de Tempo , Tomografia Computadorizada por Raios XRESUMO
UNLABELLED: The recently released Biograph mMR is the first commercially available integrated whole-body PET/MR scanner. There are considerable advantages to integrating both modalities in a single scanner that enables truly simultaneous acquisition. However, there are also concerns about the possible degradation of both PET and MR performance in an integrated system. This paper evaluates the performance of the Biograph mMR during independent and simultaneous acquisition of PET and morphologic MR data. METHODS: The NEMA NU 2-2007 protocol was followed for studying the PET performance. The following measurements were performed: spatial resolution; scatter fraction, count losses, and randoms; sensitivity; accuracy of the correction for count losses and randoms; and image quality. The quality control manual of the American College of Radiology was followed for studying the MR performance. The following measurements were performed: geometric accuracy, spatial resolution, low-contrast detectability, signal-to-noise ratio, static field (B(0)) homogeneity, radiofrequency field (B(1)) homogeneity, and radiofrequency noise. RESULTS: An average spatial resolution of 4.3 mm in full width at half maximum was measured at 1 cm offset from the center of the field of view. The system sensitivity was 15.0 kcps/MBq along the center of the scanner. The scatter fraction was 37.9%, and the peak noise-equivalent count rate was 184 kcps at 23.1 kBq/mL. The maximum absolute value of the relative count rate error due to dead-time losses and randoms was 5.5%. The average residual error in scatter and attenuation correction was 12.1%. All MR parameters were within the tolerances defined by the American College of Radiology. B(0) inhomogeneities below 1 ppm were measured in a 120-mm radius. B(1) homogeneity and signal-to-noise ratio were equivalent to those of a standard MR scanner. No radiofrequency interference was detected. CONCLUSION: These results compare favorably with other state-of-the-art PET/CT and PET/MR scanners, indicating that the integration of the PET detectors in the MR scanner and their operation within the magnetic field do not have a perceptible impact on the overall performance. The MR subsystem performs essentially like a standalone system. However, further work is necessary to evaluate the more advanced MR applications, such as functional imaging and spectroscopy.