RESUMO
Stoffenmanager is an exposure and risk assessment tool that has a control banding part, with risk bands as outcome and a quantitative exposure assessment part, with the 90th percentile of the predicted exposure as a default outcome. The main aim of the study was to investigate whether multiple users of Stoffenmanager came to the same result when modelling the same scenarios. Other aims were to investigate the differences between outcomes of the control banding part with the measured risk quota and to evaluate the conservatism of the tool by testing whether the 90th percentiles are above the measured median exposures. We investigated airborne exposures at companies in four different types of industry: wood, printing, metal foundry, and spray painting. Three scenarios were modelled and measured, when possible, at each company. When modelled, 13 users visited each company on the same occasion creating individual assessments. Consensus assessments were also modelled for each scenario by six occupational hygienists. The multiple users' outcomes were often spread over two risk bands in the control banding part, and the differences in the quantitative exposure outcomes for the highest and lowest assessments per scenario varied between a factor 2 and 100. Four parameters were difficult for the users to assess and had a large impact on the outcome: type of task, breathing zone, personal protection, and control measures. Only two scenarios had a higher measured risk quota than predicted by the control banding part, also two scenarios had slightly higher measured median exposure value than modelled consensus in the quantitative exposure assessment part. Hence, the variability between users was large but the model performed well.
Assuntos
Monitoramento Ambiental/métodos , Exposição Ocupacional/efeitos adversos , Software , Poluentes Ocupacionais do Ar/classificação , Poluentes Ocupacionais do Ar/normas , Humanos , Indústrias/normas , Exposição por Inalação/efeitos adversos , Exposição por Inalação/análise , Internet , Medicina do Trabalho , Medição de Risco/métodosRESUMO
Risk assessments based on occupational exposure to chemicals have increased since REACH (European regulation on Registration, Evaluation, Authorization, and restriction of Chemicals) came into force. The European Chemicals Agency (ECHA) recommends that chemical exposure could be calculated using exposure models and that parameters used to calculate the exposure scenario (ES) should be communicated in extended safety data sheets (e-SDS) as workplace instructions which downstream users are obligated to follow. We aimed to evaluate REACH's risk assessment approach using the Stoffenmanager® 6.1, the Advanced REACH Tool 1.5 (ART), and the European Centre for Ecotoxicology and Toxicology of Chemicals' targeted risk assessment (ECETOC TRA 3.1) exposure models. We observed 239 scenarios in three companies handling chemicals using 45 e-SDS. Risk characterization ratios (RCRs) were calculated by dividing estimated exposures by derived no-effect levels (DNELs). Observed RCRs were much lower than registered RCRs, indicating lower exposures. However, about 12% of the observed ES still had RCRs > 1, after adjustment for control measures and personal protections described in the ES, when using Stoffenmanager®. The ES with observed RCRs > 1 were the same by Stoffenmanager® and ART, but not by ECETOC TRA. Stoffenmanager and ART identified 25 adjusted scenarios with RCR > 1, while ECETOC TRA gave RCR < 1 for the same scenarios. The ES with RCR > 1 were significantly associated to chemicals with higher vapour pressure and lower DNELs than ES with RCR < 1 by Stoffenmanager®. The correlations between observed and registered RCRs were lower than those between RCRs calculated from the different models themselves; ECETOC TRA had the lowest correlation with the registered ES. These results put in question the generic ES recommended under the REACH legislation. Downstream users may get better estimates by assessing their own ES, especially for chemicals with low DNELs and high vapour pressure.
Assuntos
Monitoramento Ambiental/métodos , Substâncias Perigosas/análise , Exposição Ocupacional/análise , Medição de Risco/métodos , Algoritmos , Ecotoxicologia , Humanos , Saúde Ocupacional/normas , Medição de Risco/normasRESUMO
The use of exposure modelling tools for estimating chemical airborne exposure has increased since the European Union's REACH legislation for safe use of industrial chemicals came into force. Two tools that European Chemicals Agency recommends are Stoffenmanager® and the Advanced REACH Tool (ART). The aim of this study was to investigate the validity of these two exposure modelling tools by comparing the lack of agreement between estimated and measured exposure. We examined the airborne chemical exposure at companies in seven different types of industries: wood, printing, foundry, spray painting, flour milling, chemical industry, and plastic moulding industry. The inhalable exposure of liquids or powders at two to three situations at each company was modelled with both tools and measured. To study the validity of the tools, the mean differences and precisions (lack of agreement) of exposures from both situations handling liquids and powders were calculated by using the 50th percentile outcome of the tools and the geometric mean of the measured exposure (all data were ln transformed). For Stoffenmanager, the mean difference and precision of the situations concerning liquids were 0.22 ± 1.0 and for powders -0.024 ± 0.66. It was also shown that Stoffenmanager overestimated low exposures and underestimated high exposures. Stoffenmanager showed higher agreement with the measured exposure in the wood and flour mill industries than in foundry and the plastic moulding industry. For ART, the mean difference and precision of liquids were -0.55 ± 0.88 and for powders -1.4 ± 1.6. ART showed lower agreement with the measured exposure in the wood industry.