The increase in posterior tibial slope provides a positive biomechanical effect in posterior-stabilized total knee arthroplasty.

PURPOSE: This study aims to clarify the influence of the posterior tibial slope (PTS) on knee joint biomechanics after posterior-stabilized (PS) total knee arthroplasty (TKA) using a computer simulation. METHODS: A validated TKA computational model was used to evaluate and quantify the effects of an increased PTS. In order to conduct a squat simulation, models with a - 3° to 15° PTS using increments of 3° were developed. Forces on the quadriceps and collateral ligament, a tibial posterior translation, contact point on a polyethylene (PE) insert, and contact stress on the patellofemoral (PF) joint and post in a PE insert were compared. RESULTS: The maximum force on the quadriceps and the PF contact stress decreased with increases in the PTS. The kinematics on the tibiofemoral (TF) joint translated in an increasingly posterior manner, and the medial and lateral contact points on a PE insert were located in posterior regions with increases in the PTS. Additionally, increases in the PTS decreased the force on the collateral ligament and increased the contact stress on the post in a PE insert. A higher force on the quadriceps is required when the PTS decreases with an equivalent flexion angle. CONCLUSIONS: A surgeon should be prudent in terms of determining the PTS because an excessive increase in the PTS may lead to the progressive loosening of the TF joint due to a reduction in collateral ligament tension and failure of the post in a PE insert. Thus, we support a more individualized approach of optimal PTS determination given the findings of the study.

Influence of Increased Posterior Tibial Slope in Total Knee Arthroplasty on Knee Joint Biomechanics: A Computational Simulation Study.

BACKGROUND: The reconstructed posterior tibial slope (PTS) plays a significant role in restoring knee kinematics in cruciate-retaining-total knee arthroplasty (TKA). A few studies have reported the effect of the PTS on biomechanics. METHODS: This study investigates the effect of the PTS on tibiofemoral (TF) kinematics, patellofemoral (PF) contact stress, and forces at the quadriceps, posterior cruciate ligament (PCL) and collateral ligament after cruciate-retaining-TKA using computer simulations. The simulation for the validated TKA finite element model was performed under deep knee bend condition. All analyses were repeated from -3° to 15° PTS in increments of 3°. RESULTS: The kinematics on the TF joint translated increasingly posteriorly when the PTS increased. Medial and lateral contact points translated in posterior direction in extension and flexion as PTS increased. The maximum contact stress on the PF joint and quadriceps, and collateral ligament force decreased when the PTS increased. An implantation of the tibial plate with increased PTS reduced the PCL load. Physiologic insert movement led to an increasingly posterior position of the femur and reduced quadriceps force especially for knee flexion angles above high flexion (120°) when compared to TKA with a decreased slope of the tibial base plate. CONCLUSION: An increase in the PTS increased medial and lateral movements without paradoxical motion. However, an excessive PTS indicated progressive loosening of the TF joint gap due to a reduction in collateral ligament tension during flexion.

Active site engineering of Zn-doped mesoporous ceria toward highly efficient organophosphorus hydrolase-mimicking nanozyme.

Hydrolase-mimicking nanozymes have received increasing attention in recent years, but the effective rational design and development of these materials has not been realized, as they are not at present considered a critical research target. Herein, we report that Zn-doped mesoporous ceria (Zn-m-ceria) engineered to have an abundance of two different active sites with different functions-one that allows both co-adsorption binding of organophosphate (OP) and water and another that serves as a general base-has significant organophosphorus hydrolase (OPH)-like catalytic activity. Specifically, Zn-m-ceria exhibits a catalytic efficiency over 75- and 25-fold higher than those of m-ceria and natural OPH, respectively. First-principles calculations reveal the importance of Zn for the OPH-mimicking activity of the material, promoting substrate adsorption and proton-binding. The OPH-like Zn-m-ceria catalyst is successfully applied to detect a model OP, methyl paraoxon, in spiked tap water samples with excellent sensitivity, stability, and detection precision. We expect that these findings will promote research based on the rational engineering of the active site of nanozymes and efficient strategies for obtaining a diverse range of catalysts that mimic natural enzymes, and hence the utilization in real-world applications of enzyme-mimicking catalysts with properties superior to their natural analogs should follow.

Spongy Ag Foam for Soft and Stretchable Strain Gauges.

Strain gauges, particularly for wearable sensing applications, require a high degree of stretchability, softness, sensitivity, selectivity, and linearity. They must also steer clear of challenges such as mechanical and electrical hysteresis, overshoot behavior, and slow response/recovery times. However, current strain gauges face challenges in satisfying all of these requirements at once due to the inevitable trade-offs between these properties. Here, we present an innovative method for creating strain gauges from spongy Ag foam through a steam-etching process. This method simplifies the traditional, more complex, and costly manufacturing techniques, presenting an eco-friendly alternative. Uniquely, the strain gauges crafted from this method achieve an unparalleled gauge factor greater than 8 × 103 at strains exceeding 100%, successfully meeting all required attributes without notable trade-offs. Our work includes systematic investigations that reveal the intricate structure-property-performance relationship of the spongy Ag foam with practical demonstrations in areas such as human motion monitoring and human-robot interaction. These breakthroughs pave the way for highly sensitive and selective strain gauges, showing immediate applicability across a wide range of wearable sensing applications.

A machine-learning-enabled smart neckband for monitoring dietary intake.

The increasing need for precise dietary monitoring across various health scenarios has led to innovations in wearable sensing technologies. However, continuously tracking food and fluid intake during daily activities can be complex. In this study, we present a machine-learning-powered smart neckband that features wireless connectivity and a comfortable, foldable design. Initially considered beneficial for managing conditions such as diabetes and obesity by facilitating dietary control, the device's utility extends beyond these applications. It has proved to be valuable for sports enthusiasts, individuals focused on diet control, and general health monitoring. Its wireless connectivity, ergonomic design, and advanced classification capabilities offer a promising solution for overcoming the limitations of traditional dietary tracking methods, highlighting its potential in personalized healthcare and wellness strategies.

Rapid Self-Healing Hydrogel with Ultralow Electrical Hysteresis for Wearable Sensing.

Self-healing hydrogels are in high demand for wearable sensing applications due to their remarkable deformability, high ionic and electrical conductivity, self-adhesiveness to human skin, as well as resilience to both mechanical and electrical damage. However, these hydrogels face challenges such as delayed healing times and unavoidable electrical hysteresis, which limit their practical effectiveness. Here, we introduce a self-healing hydrogel that exhibits exceptionally rapid healing with a recovery time of less than 0.12 s and an ultralow electrical hysteresis of less than 0.64% under cyclic strains of up to 500%. This hydrogel strikes an ideal balance, without notable trade-offs, between properties such as softness, deformability, ionic and electrical conductivity, self-adhesiveness, response and recovery times, durability, overshoot behavior, and resistance to nonaxial deformations such as twisting, bending, and pressing. Owing to this unique combination of features, the hydrogel is highly suitable for long-term, durable use in wearable sensing applications, including monitoring body movements and electrophysiological activities on the skin.

A review of microvascular ear replantation.

Microvascular ear replantation is a significant challenge because of the small size of the vessels and the fact that traumatic amputations are frequently avulsed. The zone of trauma is therefore extended and the primary repair of the injured vessel is rendered unlikely. The purpose of this study is to review the literature of ear replantation. A review of the relevant literature that has been published since 1980 revealed 47 cases reported in 37 publications. We present 5 cases from our own experience and analyze a total 52 cases of microvascular ear replantation. The patient's age, sex, degree of amputation, cause of injury, ischemic time, method of arterial and venous anastomosis, complications, any additional outflow used, postoperative medications, the requirement for transfusions, and the number of hospital admission days are described. Successful microvascular ear replantations require anastomosis of the vessels if possible. Rather than a vein graft, primary repair of the vessels, or at least pedicled repair of the artery, should be considered to ensure flap survival. In addition, vein repair should be considered if possible to ensure the secure drainage of blood from the replant. With secure circulation, the replant can survive, resulting in a very satisfactory outcome.

Rh-coordinated histidyl bolaamphiphile assembly: a catalyst for the isomerization of cis-stilbene and cis-alkene.

In this study, we present a colloidal assembly of histidyl bolaamphiphiles whose imidazoles coordinate with rhodium ions (HisC7[Rh]) to exhibit catalytic isomerization activity for cis-stilbene and cis-alkene molecules. The histidyl bolaamphiphiles self-assemble to form a soft scaffold that functions analogously to an apoenzyme. This scaffold exposes multiple histidyl imidazoles and carboxylates on its surface, to which rhodium ions bind, generating catalytically active sites. The Rh coordination with the biochemical functional groups was verified through comprehensive vibrational spectroscopy and calorimetry. The colloidal HisC7[Rh] demonstrated a significant catalytic effect on the isomerization of cis- to trans-stilbene under mild H2 conditions, resulting in 69% yield of trans-stilbene. In contrast, when Rh(cod)2BF4 was employed as a control catalyst, only the hydrogenated products of bibenzyl were obtained. These findings underscore the crucial role of histidyl motifs in exhibiting unique catalytic isomerization activity through the coordination with Rh. The catalytic activity of HisC7[Rh] is governed by several factors, such as rhodium content, solvent composition, temperature, and H2 pressure. Moreover, HisC7[Rh] displayed moderate isomerization activity towards not only stilbene but also unsaturated fatty acid isomers, highlighting its expansive potential as an isomerization catalyst.

In Situ Spray Polymerization of Conductive Polymers for Personalized E-textiles.

E-textiles, also known as electronic textiles, seamlessly merge wearable technology with fabrics, offering comfort and unobtrusiveness and establishing a crucial role in health monitoring systems. In this field, the integration of custom sensor designs with conductive polymers into various fabric types, especially in large areas, has presented significant challenges. Here, we present an innovative additive patterning method that utilizes a dual-regime spray system, eliminating the need for masks and allowing for the programmable inscription of sensor arrays onto consumer textiles. Unlike traditional spray techniques, this approach enables in situ, on-the-fly polymerization of conductive polymers, enabling intricate designs with submillimeter resolution across fabric areas spanning several meters. Moreover, it addresses the nozzle clogging issues commonly encountered in such applications. The resulting e-textiles preserve essential fabric characteristics such as breathability, wearability, and washability while delivering exceptional sensing performance. A comprehensive investigation, combining experimental, computational, and theoretical approaches, was conducted to examine the critical factors influencing the operation of the dual-regime spraying system and its role in e-textile fabrication. These findings provide a flexible solution for producing e-textiles on consumer fabric items and hold significant implications for a diverse range of wearable sensing applications.

Wearable Sensor Patch with Hydrogel Microneedles for In Situ Analysis of Interstitial Fluid.

Continuous real-time monitoring of biomarkers in interstitial fluid is essential for tracking metabolic changes and facilitating the early detection and management of chronic diseases such as diabetes. However, developing minimally invasive sensors for the in situ analysis of interstitial fluid and addressing signal delays remain a challenge. Here, we introduce a wearable sensor patch incorporating hydrogel microneedles for rapid, minimally invasive collection of interstitial fluid from the skin while simultaneously measuring biomarker levels in situ. The sensor patch is stretchable to accommodate the swelling of the hydrogel microneedles upon extracting interstitial fluid and adapts to skin deformation during measurements, ensuring consistent sensing performance in detecting model biomarker concentrations, such as glucose and lactate, in a mouse model. The sensor patch exhibits in vitro sensitivities of 0.024 ± 0.002 µA mM-1 for glucose and 0.0030 ± 0.0004 µA mM-1 for lactate, with corresponding linear ranges of 0.1-3 and 0.1-12 mM, respectively. For in vivo glucose sensing, the sensor patch demonstrates a sensitivity of 0.020 ± 0.001 µA mM-1 and a detection range of 1-8 mM. By integrating a predictive model, the sensor patch can analyze and compensate for signal delays, improving calibration reliability and providing guidance for potential optimization in sensing performance. The sensor patch is expected to serve as a minimally invasive platform for the in situ analysis of multiple biomarkers in interstitial fluid, offering a promising solution for continuous health monitoring and disease management.

Transparent Intracellular Sensing Platform with Si Needles for Simultaneous Live Imaging.

Vertically ordered Si needles are of particular interest for long-term intracellular recording owing to their capacity to infiltrate living cells with negligible damage and minimal toxicity. Such intracellular recordings could greatly benefit from simultaneous live cell imaging without disrupting their culture, contributing to an in-depth understanding of cellular function and activity. However, the use of standard live imaging techniques, such as inverted and confocal microscopy, is currently impeded by the opacity of Si wafers, typically employed for fabricating vertical Si needles. Here, we introduce a transparent intracellular sensing platform that combines vertical Si needles with a percolated network of Au-Ag nanowires on a transparent elastomeric substrate. This sensing platform meets all prerequisites for simultaneous intracellular recording and imaging, including electrochemical impedance, optical transparency, mechanical compliance, and cell viability. Proof-of-concept demonstrations of this sensing platform include monitoring electrical potentials in cardiomyocyte cells and in three-dimensionally engineered cardiovascular tissue, all while conducting live imaging with inverted and confocal microscopes. This sensing platform holds wide-ranging potential applications for intracellular research across various disciplines such as neuroscience, cardiology, muscle physiology, and drug screening.

Novel microsatellite markers of Meretrix petechialis and cross-species amplification in related Taxa (Bivalvia: Veneroida).

The Asian hard clam, Meretrix petechialis, is an economically important bivalve, but its catch and population sizes are decreasing rapidly, owing to many factors, including large-scale reclamation of its natural habitat on the western coast of the Korean peninsula. Attempts to restore the resources and production of this species require genetic structure and diversity information. In this study, we developed 15 microsatellite markers from a partial genomic library enriched in GT repeats. Nine of these markers were polymorphic, with an average allele number of six, and six were monomorphic in 95 tested individuals. No linkage disequilibrium was found between any pair of loci (p > 0.05), and deviations from the Hardy-Weinberg equilibrium (HWE) test showing excess of heterozygotes was observed in only one of nine loci. In addition, no null alleles or genetic differentiation between two tested populations were detected. A cross-species amplification in 12 species of four families resulted in two M. petechialis-specific loci and three possible universal markers. This information will be useful in the future development of high-quality artificial seedlings and sustainable resource management.

Ilizarov distraction and vascularized fibular osteocutaneous graft for postosteomyelitis skeletal deformity of the forearm.

The reconstruction of large skeletal defects secondary to osteomyelitis is a challenging problem. This paper reports on the treatment of bone defects caused by osteomyelitis of the radius using an Ilizarov distraction technique and a vascularized fibular graft. A 25-year-old man first presented with a right radial defect caused by osteomyelitis when he was 3 years old. His right forearm was shortened and angulated with a dislocation of the distal radio-ulnar joint. The defect in the radial shaft was noted on a radiograph. The reconstruction of his radial bone defect was performed in three separate operations. A two-stage Ilizarov application was performed. Ten months after this operation, the radial bone defect was reconstructed with a vascularized fibular osteocutaneous graft. The right radius was shortened by 10 mm due to the angulation in the distal fixation of the graft 14 years after surgery. Although limited motions of the right thumb extension and wrist supination were noted, other hand functions were adequately restored. The Ilizarov technique is an effective method for correcting distal radio-ulnar joint dislocations and shortened, angulated ulnar bones. The specific features of the vascularized fibular graft make it suitable for the bone reconstruction of large defects in the radius.

Free-flap reconstruction of the scalp: donor selection and outcome.

Wide, complex defects of the scalp caused by various insults always represent reconstructive challenges for surgeons. Our study group consisted of 18 patients (14 males and 4 females) with a mean age of 40.2 years. Nineteen free-tissue transfers were used to reconstruct the scalp defects. The selected cases included 8 latissimus dorsi muscle flaps, 3 latissimus dorsi myocutaneous flaps, 2 rectus abdominis muscle flaps, 3 omental flaps, 1 scapular flap, 1 radial forearm flap, and 1 groin flap. Twelve patients had acute or subacute wounds resulting from trauma or craniotomy, 4 had primary cancer, and 2 had neurofibromatosis. Commonly used recipient vessels were the superficial temporal artery and vein. No flap procedure had morbidity due to vessel compromise, and the overall flap success rate was thus 100%. No major donor-site morbidity was observed. All cases underwent primary closure of donor sites except for one receiving split-thickness skin grafting. In cases where muscle or omental free flaps covered skin grafts, patients were more satisfied because of increased durability and well-fitted wigs. We advocate variable free-tissue transfers for the reconstruction of large defects of the scalp related to the sizes, sites, and extents of the involvement.

Principles for Controlling the Shape Recovery and Degradation Behavior of Biodegradable Shape-Memory Polymers in Biomedical Applications.

Polymers with the shape memory effect possess tremendous potential for application in diverse fields, including aerospace, textiles, robotics, and biomedicine, because of their mechanical properties (softness and flexibility) and chemical tunability. Biodegradable shape memory polymers (BSMPs) have unique benefits of long-term biocompatibility and formation of zero-waste byproducts as the final degradable products are resorbed or absorbed via metabolism or enzyme digestion processes. In addition to their application toward the prevention of biofilm formation or internal tissue damage caused by permanent implant materials and the subsequent need for secondary surgery, which causes secondary infections and complications, BSMPs have been highlighted for minimally invasive medical applications. The properties of BSMPs, including high tunability, thermomechanical properties, shape memory performance, and degradation rate, can be achieved by controlling the combination and content of the comonomer and crystallinity. In addition, the biodegradable chemistry and kinetics of BSMPs, which can be controlled by combining several biodegradable polymers with different hydrolysis chemistry products, such as anhydrides, esters, and carbonates, strongly affect the hydrolytic activity and erosion property. A wide range of applications including self-expending stents, wound closure, drug release systems, and tissue repair, suggests that the BSMPs can be applied as actuators on the basis of their shape recovery and degradation ability.

Application of Macro-Instrumented Indentation Test for Superficial Residual Stress and Mechanical Properties Measurement for HY Steel Welded T-Joints.

HY-80 and HY-100 steels, widely used in constructing large ocean vessels and submarine hulls, contain mixed microstructures of tempered bainite and martensite and provide high tensile strength and toughness. Weld integrity in HY steels has been studied to verify and optimize welding conditions. In this study, the T-joint weld coupons, HY80 and HY100, were fabricated from HY-80 and HY-100 steel plates with a thickness of 30 mm as base metals by submerged-arc welding. Flux-cored arc welding was performed on an additional welding coupon consisting of HY-100 to evaluate the effect of repair welds (HY100RP). Microstructures in the heat-affected zones (HAZ) were thoroughly analyzed by optical observation. Instrumented indentation testing, taking advantage of local characterization, was applied to assess the yield strength and the residual stress of the HAZ and base regions. The maximum hardness over 400 HV was found in the HAZ due to the high volume fraction of untempered martensite microstructure. The yield strength of the weld coupons was evaluated by indentation testing, and the results showed good agreement with the uniaxial tensile test (within 10% range). The three coupons showed similar indentation residual stress profiles on the top and bottom surfaces. The stress distribution of the HY100 coupon was comparable to the results from X-ray diffraction. HY100RP demonstrated increased tensile residual stress compared to the as-welded coupon due to the effect of the repair weld (323 and 103 MPa on the top and bottom surfaces). This study verifies the wide applicability of indentation testing in evaluating yield strength and residual stress.

Time-Sequencing of the Neutrophil-to-Lymphocyte Ratio to Predict Prognosis of Triple-Negative Breast Cancer.

Since triple-negative breast cancers (TNBCs) have varying prognoses, it is important to identify subgroups with particularly poor prognosis. The aim of this study was to assess whether changes in the neutrophil-to-lymphocyte ratio (NLR) during the treatment process were associated with poor prognosis in TNBC patients. This study included 600 TNBC patients who underwent surgery from January 2005 to December 2016. The associations of the NLR and clinicopathologic factors with breast cancer recurrence and survival in patients who underwent both definitive local treatment (total mastectomy or breast-conserving surgery with radiotherapy) and systemic chemotherapy were analyzed. The NLRs at four time points (before surgery, before chemotherapy, before radiotherapy, and 1 year after surgery) were assessed. The univariate analysis showed that changes in the NLR before the start of radiotherapy (odds ratio: 1.115, confidence interval: 1.011-1.229) and 1 year after surgery (odds ratio: 1.196, confidence interval: 1.057-1.354) significantly increased the risk of recurrence or death. In multivariate analysis, T stage, N stage, and changes in the NLR were significant factors. A time-sequenced NLR may reflect the prognosis of TNBC patients. A poor prognosis is expected in patients whose NLR increases during treatment compared to the preoperative NLR, and additional treatment is needed.

Synthesis of aminoquinazoline derivatives and their antiproliferative activities against melanoma cell line.

The synthesis of a novel series of aminoquinazoline derivatives 1a-r and their antiproliferative activities against A375 human melanoma cell line were described. Among them, six compounds showed superior antiproliferative activities to Sorafenib as a reference compound. In particular, the representative compound 1q bearing chromen-4-one moiety exhibited excellent antiproliferative activity (IC(50)=0.006 µM) and good selectivity over HS27 fibroblast cell line.

Self color-changing ordered mesoporous ceria for reagent-free colorimetric biosensing.

A reagent-free colorimetric detection method using mesoporous cerium oxide with a large pore size trapping an oxidative enzyme has been developed and glucose is sensitively detected with a limit of detection of 10 µM by supporting glucose oxidase on mesoporous cerium oxide.

Molecular phylogenetic, population genetic and demographic studies of Nodularia douglasiae and Nodularia breviconcha based on CO1 and 16S rRNA.

Freshwater mussels belonging to the genus Nodularia (Family Unionidae) are known to be widely distributed in East Asia. Although phylogenetic and population genetic studies have been performed for these species, there still remain unresolved questions in their taxonomic status and biogeographic distribution pathways. Here, the nucleotide sequences of CO1 and 16S rRNA were newly determined from 86 N. douglasiae and 83 N. breviconcha individuals collected on the Korean Peninsula. Based on these data, we revealed the following results: (1) N. douglasiae can be divided into the three genetic clades of A (only found in Korean Peninsula), B (widely distributed in East Asia), and C (only found in the west of China and Russia), (2) the clade A is not an independent species but a concrete member of N. douglasiae given the lack of genetic differences between the clades A and B, and (3) N. breviconcha is not a subspecies of N. douglasiae but an independent species apart from N. douglasiae. In addition, we suggested the plausible scenarios of biogeographic distribution events and demographic history of Nodularia species.