Polymer Surface Textured with Nanowire Bundles to Repel High-Speed Water Drops.

Water drops impacting windshields of high-speed trains and aircraft as well as blades in steam turbine power generators obliquely and at high speeds are difficult to repel. Impacting drops penetrate the void regions of nanotextured and microtextured superhydrophobic coatings, with this pinning resulting in the loss of drop mobility. In order to repel high-speed water drops, we nanotextured polymer surfaces with nanowire bundles separated from their neighbors by microscale void regions, with the nanowires in a bundle separated from their neighbors by nanoscale void regions. Water drops with speeds below a critical speed rebound completely. Water drops with speeds exceeding a critical speed rebound partially, but residual droplets that begin to be pinned undergo a spontaneous dewetting process and slide off. The natural oscillations of residual droplets drive this dewetting process in the interbundle void regions, resulting in a transition from the sticky Wenzel state to the slippery Cassie state without external stimuli.

Oxidation and corrosion behaviors of Mg-based nanoparticles.

Various Mg-based nanoparticles were prepared by evaporating bulk magnesium in the atmospheres of Ar, Ar+N2 and CH4, respectively. The formations, phases, morphologies, thermal properties and corrosion behaviors of these kinds of nanocomposite particles were investigated by means of X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), thermogravimetric-differential thermal analysis (TG/DTA) and potentiodynamic polarisation scan (PPS). It is shown that the Mg-based nanoparticles produced in Ar and Ar+N2 atmospheres have hexangular crystal habits with particles' sizes ranging from 50 to 400 nm, while the nanoparticles produced in CH4 atmosphere have amorphous carbon out layers with particles' sizes among 20-100 nm. TG/DTA results show that two-steps oxidation process can be confirmed for all samples, which may be attributed to the oxidations of out layer and core of nanoparticle. The CH4 atmosphere-prepared nanoparticles exhibit better corrosion resistance properties due to its peculiar carbon doping.

Lifetime of anode polymer in magnetically insulated ion diodes for high-intensity pulsed ion beam generation.

Generation of high-intensity pulsed ion beam (HIPIB) has been studied experimentally using polyethylene as the anode polymer in magnetically insulated ion diodes (MIDs) with an external magnetic field. The HIPIB is extracted from the anode plasma produced during the surface discharging process on polyethylene under the electrical and magnetic fields in MIDs, i.e., high-voltage surface breakdown (flashover) with bombardments by electrons. The surface morphology and the microstructure of the anode polymer are characterized using scanning electron microscopy and differential scanning calorimetry, respectively. The surface roughening of the anode polymer results from the explosive release of trapped gases or newly formed gases under the high-voltage discharging, leaving fractured surfaces with bubble formation. The polyethylene in the surface layer degrades into low-molecular-weight polymers such as polyethylene wax and paraffin under the discharging process. Both the surface roughness and the fraction of low molecular polymers apparently increase as the discharging times are prolonged for multipulse HIPIB generation. The changes in the surface morphology and the composition of anode polymer lead to a noticeable decrease in the output of ion beam intensity, i.e., ion current density and diode voltage, accompanied with an increase in instability of the parameters with the prolonged discharge times. The diode voltage (or surface breakdown voltage of polymer) mainly depends on the surface morphology (or roughness) of anode polymers, and the ion current density on the composition of anode polymers, which account for the two stages of anode polymer degradation observed experimentally, i.e., stage I which has a steady decrease of the two parameters and stage II which shows a slow decrease, but with an enhanced fluctuation of the two parameters with increasing pulses of HIPIB generation.

Measurements of coating density using ultrasonic reflection coefficient phase spectrum.

A nondestructive method to determine the density of coating has been proposed in this paper based on the ultrasonic reflection coefficient phase spectrum (URCPS). A model was set up first to represent the ultrasonic waves reflected from a coating system at normal incident, and the relation between the extremum of URCPS and the coating density was established to provide the principle of determining the density. The ultrasonic method was validated on a series of ZrO2-7wt.%Y2O3 (YSZ) coatings with various density. The specimens were prepared by electric beam physical vapor deposit (EB-PVD). After deposition, the specimens were irradiated using high-intensity pulsed ion beam (HIPIB) at different ion current density of 100 and 200A/cm2 to change coating density. The coating densities of as-deposited and post irradiation by HIPIB were derived to be 4940-5030, 5200-5320 and 5390-5470kg/m3, respectively. The relative error between the coating density measured by the ultrasonic method and Archimedean principle ranging from 2.53% to 6.11%, indicates that the proposed ultrasonic quantification method provides a reliable nondestructive way to determine coating density.