RESUMO
In situ burning (ISB) is an oil spill response technique including ignition and burning to remove oil on the water surface. The technique rapidly and effectively removes large portions of the oil. However, the combustion process causes a large smoke plume and leaves a viscous residue in the water. During six large-scale experimental burns in the North Sea in 2018 and 2019, the smoke plume, released oil and contained residues were analysed. The objectives were to document the content of particles and gases in the smoke plume, properties of both the released oils and residues, and the effectiveness of the burns. Oseberg crude oil, Ultra Low Sulphur Fuel Oil (ULSFO), Intermediate Fuel Oil (IFO180) and Marine Gas Oil (MGO) were released into a fire-boom and ignited. Particles and gases in the smoke plume were monitored using drones with several sensors. Soot particle monitoring indicated that more than 90% of the particles produced during the burns were <1 µm. Soot fallout was mainly limited to visible smoke, and the particle concentration was highest directly under the smoke plume and declined with distance from the burn. Gas monitoring in the smoke indicated low concentrations of SO2 and NOX (<2 ppm), and the concentrations of CO2 and CO were within air quality standards. Black Carbon produced relative to the amount of oil burned was 10-18%. The burn efficiency varied and were estimated to 80-91% for Oseberg, >90% for MGO, and <60% for both ULSFO and IFO180. The present paper addresses the results of the smoke plume monitoring, properties of the ISB residues and the burn efficiency.
Assuntos
Poluentes Atmosféricos , Poluição do Ar , Queimaduras , Poluição por Petróleo , Petróleo , Poluentes Atmosféricos/análise , Poluição do Ar/análise , Humanos , Óleos/análise , Petróleo/análise , Poluição por Petróleo/análiseRESUMO
Knowledge of the vertical migration pattern of sea lice (Lepeophtheirus salmonis) copepodites is necessary for designing efficient measures to prevent lice infestations on farmed Atlantic salmon (Salmo Salar) in sea-cages. However, data can be challenging to acquire at a large scale under realistic circumstances without interfering with the natural behavior of the specimen. A mesocosm platform was built to help acquire this data consisting of a sensor package in an underwater housing being pulled up and down along a 11-meter-long transparent tube containing planktonic organisms while collecting image-, temperature- and spectrometer data. The platform was placed at a salmon farm and the acrylic tube was filled with L. salmonis copepodites and was pre-programmed to run a profile scan twice per hour for four consecutive days. Using a fully convolutional neural network, the copepodites were automatically counted - creating a depth profile of detected lice and measured light specter. The final results showed a diurnal migration pattern throughout the test period.â¢Capable of acquiring vertical density profiles of any aquatic species between 0,5 - 10 mm down to 11 m below the surface.â¢Fully automated and can be left unintended for weeks while collecting data.
RESUMO
The main objective with subsea mechanical dispersion (SSMD) is to influence the fate of an oil spill in the marine environment by significantly reducing oil droplet sizes from subsea release of oil. Earlier studies have indicated that the capability of SSMD to reduce oil droplet sizes is comparable to subsea dispersant injection (SSDI). Earlier testing of SSMD has mainly used a low viscus paraffinic oil. Focus for this study was to study SSMD and SSDI effectiveness using five oil types spanning out a wide variation of relevant oil properties. Effectiveness was quantified as the reduction in oil droplet sizes measured by a Silhouette camera. Testing of the two technologies were completed in the same experiment on a simulated subsea release. The results show a variation in effectiveness for both technologies as a function of oil properties. SSMD and SSDI showed comparable effectiveness for all oils tested.
Assuntos
Poluição por Petróleo , Petróleo , Poluentes Químicos da Água , Poluição por Petróleo/análise , Óleos , Poluentes Químicos da Água/análiseRESUMO
The main objective of subsea mechanical dispersion (SSMD) is to reduce the oil droplet sizes from a subsea oil release, thereby influencing the fate and behaviour of the released oil in the marine environment. Subsea water jetting was identified as a promising method for SSMD and imply that a water jet is used to reduce the particle size of the oil droplets initially formed from the subsea release. This paper presents the main findings from a study including small-scale testing in a pressurised tank, via laboratory basin testing, to large-scale outdoor basin testing. The effectiveness of SSMD increases with the scale of the experiments. From a five-fold reduction in droplet sizes for small-scale experiments to more than ten-fold for large-scale experiments. The technology is ready for full-scale prototyping and field testing. Large-scale experiments performed at Ohmsett indicate that SSMD could be comparable to subsea dispersant injection (SSDI) in reducing oil droplet sizes.
Assuntos
Poluição por Petróleo , Petróleo , Poluentes Químicos da Água , Poluição por Petróleo/análise , Água , Poluentes Químicos da Água/análise , Tamanho da PartículaRESUMO
Microscopic imaging and morphometric measurement of fish embryos and larvae is essential in environmental monitoring of fish populations and to evaluate larvae development in aquaculture. Traditional microscopy methods require time-consuming, repetitive work by human experts. We present a method for fast imaging and analysis of millimetre-scale ichthyoplankton suspended in seawater. Our system can be easily built from common and off-the-shelf components and uses open-source software for image capture and analysis. Our system obtains images of similar quality to traditional microscopy, and biological measurements comparable to those by human experts, with minimal human interaction. This saves time and effort, while increasing the size of data sets obtained. We demonstrate our approach with cod eggs and larvae, and present results showing biologically relevant endpoints including egg diameter, larval standard length, yolk volume and eye diameter, with comparison to similar measurements reported in the literature. ⢠High throughput, microscope-scale imaging of fish eggs and larvae ⢠Automated measurement of biologically relevant endpoints ⢠Easily built from off-the-shelf components and open-source software.
RESUMO
Small-scale experiments performed at SINTEF, Norway in 2011-12 led to the development of a modified Weber scaling algorithm. The algorithm predicts initial oil droplet sizes (d50) from a subsea oil and gas blowout. It was quickly implemented in a high number of operational oil spill models used to predict fate and effect of subsea oil releases both in academia and in the oil industry. This paper presents experimental data from large-scale experiments generating oil droplet data in a more realistic multi-millimeter size range for a subsea blow-out. This new data shows a very high correlation with predictions from the modified Weber scaling algorithm both for untreated oil and oil treated by dispersant injection. This finding is opposed to earlier studies predicting significantly smaller droplets, using a similar approach for estimating droplet sizes, but with calibration coefficients that we mean are not representative of the turbulence present in such releases.
Assuntos
Poluição por Petróleo , Petróleo , Poluentes Químicos da Água , Calibragem , Noruega , Petróleo/análise , Poluição por Petróleo/análise , Poluentes Químicos da Água/análiseRESUMO
Increased knowledge about the fate and behaviour of weathered oil in different sea ice conditions is essential for our ability to model oil spill trajectories in ice more precisely and for oil spill response decision making in northern and Arctic areas. As part of the 3-year project: "Fate, Behaviour and Response to Oil Drifting into Scattered Ice and Ice Edge in the Marginal Ice Zone", a novel wave and current flume was built to simulate these processes in the laboratory. This paper discusses some of the findings from this project, which included Marine Gas Oil and four Norwegian crude oils. All crude oils were weathered prior to testing, simulating having drifted on the sea surface for a period (tentatively 1-3 days) before encountering ice. The build-up of oil drifting against an ice barrier and horizontal and vertical migration of oil droplets under solid ice and in frazil ice was studied.
Assuntos
Poluição por Petróleo/análise , Petróleo , Regiões Árticas , Camada de Gelo , NoruegaRESUMO
Oil slick thickness is a key parameter for the behaviour of oil spilled at sea. It influences evaporation and entrainment, viable response options, and the risk to marine life at the surface. Determining this value is therefore of high relevance in oil spill modelling. In open water, oil can spread as thin films due to gravity alone, and may be further dispersed by horizontal diffusion and differential advection. In the presence of ice, however, a thin oil slick may become concentrated to higher thickness, if compressed against the ice edge. In the present study, we develop a simple model for the thickness of oil forced against a barrier by a current. We compare our theory to flume experiments, and obtain reasonable agreement. We describe an implementation in a Lagrangian oil spill model, and present some examples. We discuss the operational applicability, and suggest further research needs.
Assuntos
Poluição por Petróleo/análise , Petróleo , Poluentes Químicos da Água/análise , GeloRESUMO
Limited experimental and field data are available describing oil droplet formation from subsea releases at high pressure. There are also analytical challenges quantifying oil droplets over a wide size and concentrations range at high pressure. This study quantified oil droplets released from an orifice in seawater at low and high pressure (5â¯m and 1750â¯m depth). Oil droplet sizes were quantified using a newly developed sensor (Silhouette camera or SilCam). The droplet sizes measured during experiments at low and high pressure, using the same release conditions, showed no significant difference as a function of pressure. This lack of a pressure effect on oil droplet sizes was observed for both untreated oil and for droplet formation during subsea dispersant injection or SSDI. This strongly indicates that the effectiveness of SSDI is not influenced by water depth or pressure, at least for simulated subsea releases of oil alone (no gas).
Assuntos
Hidrologia/métodos , Petróleo , Desenho de Equipamento , Hidrologia/instrumentação , Laboratórios , Gás Natural , PressãoRESUMO
This paper presents a compilation of data describing interfacial tension between oil and seawater (IFT(oil-water)) as a function of dispersant dosage. The data are from several earlier laboratory studies simulating subsea oil blowouts to evaluate subsea injection of dispersant (SSDI). Three dispersants were tested with four oil types to give a large variation in oil properties (paraffinic, light, waxy and asphaltenic). A general expression for IFT(oil-water) as a function of dispersant dosage is proposed based on the compiled data. IFT(oil-water) versus dosage is needed by algorithms to predict oil droplet sizes from subsea releases. However, such a relationship based on averaged data should be used with care and IFT measurements on the actual oil-dispersant combination should always be preferred.
Assuntos
Poluição por Petróleo , Água do Mar/química , Tensoativos/química , Poluentes Químicos da Água/química , Recuperação e Remediação Ambiental/métodos , Petróleo , Tensão SuperficialRESUMO
The main objective with this study has been to study injection techniques for subsea dispersant injection (SSDI) to recommend techniques relevant for both laboratory studies and operational response equipment. The most significant factor was the injection point of the dispersant in relation to the release of the oil. The dispersant should be injected immediately before or after the oil is released. Then the dispersant will mix into the oil and reduce IFT before the oil enters the turbulent zone where initial droplet formation occurs. All injection techniques tested gave significant reductions in oil droplet sizes. However, due to the rapid oil droplet formation in turbulent jets and possible formation of surfactant aggregates in the oil, premixing of dispersants should not be used for experimental studies of subsea dispersant injection. This could underestimate dispersant effectiveness and produce results that might not be representative for up-scaled field conditions.
Assuntos
Lipídeos/química , Modelos Teóricos , Poluição por Petróleo/prevenção & controle , Tensoativos/química , Poluentes Químicos da Água/análise , Poluição da Água/prevenção & controle , Mar do Norte , Noruega , Poluição por Petróleo/análise , Poluição da Água/análiseRESUMO
The objective of this paper is to provide a simple extension of the much-used gravity spreading model for oil on calm water to account for the spreading behavior of waxy crude oils in cold waters - including the observed retardation and eventual termination of spreading at certain oil film thicknesses. This peculiar behavior is not predicted by traditional spreading models for oil on calm water (i.e. viscous-gravity spreading models), but may occur due to non-Newtonian oil properties caused by precipitation of wax at low temperatures. To clarify the spreading behavior of such oils, SINTEF has conducted a series of laboratory experiments with a range of waxy oil mixtures. The present paper contains analyses of data from these experiments, including favorable comparisons with calculations by a proposed improved surface spreading model.
Assuntos
Modelos Teóricos , Poluição por Petróleo/análise , Petróleo/análise , Água do Mar/química , Temperatura Baixa , Viscosidade , Movimentos da ÁguaRESUMO
Physically and chemically (Corexit 9500) generated Macondo 252 oil dispersions, or emulsions (no Corexit), were prepared in an oil-on-seawater mesocosm flume basin at 30-32 °C, and studies of oil compound depletion performed for up to 15 days. The use of Corexit 9500 resulted in smaller median droplet size than in a physically generated dispersion. Rapid evaporation of low boiling point oil compounds (C⩽15) appeared in all the experiments. Biodegradation appeared to be an important depletion process for compounds with higher boiling points in the dispersions, but was negligible in the surface emulsions. While n-alkane biodegradation was faster in chemically than in physically dispersed oil no such differences were determined for 3- and 4-ring PAH compounds. In the oil dispersions prepared by Corexit 9500, increased cell concentrations, reduction in bacterial diversity, and a temporary abundance of bacteria containing an alkB gene were associated with oil biodegradation.
Assuntos
Bactérias/metabolismo , Emulsões/química , Hidrocarbonetos/metabolismo , Petróleo/análise , Água do Mar/química , Alcanos/metabolismo , Bactérias/genética , Biodegradação Ambiental , Hidrocarbonetos/químicaRESUMO
Results from a comprehensive oil weathering and dispersant effectiveness study of the MC252 crude oil have been used to predict changes in oil properties due to weathering on the sea surface and to estimate the effective "time window" for dispersant application under various sea conditions. MC252 oil is a light paraffinic crude oil, for which approximately 55 wt.% will evaporate within 3-5 days when drifting on the sea. An unstable and low-viscosity water-in-oil (w/o) emulsion are formed during the first few days at the sea surface. This allows a high degree of natural dispersion when exposed to breaking wave conditions. Under calm sea conditions, a more stable and light-brown/orange colored water-in-oil (w/o) emulsion may start to form after several days, and viscosities of 10,000-15,000 mPa s can be achieved after 1-2 weeks. The "time window" for effective use of dispersants was estimated to be more than 1 week weathering at sea.
Assuntos
Petróleo/análise , Poluentes Químicos da Água/química , Emulsões , Pressão , Fatores de Tempo , ViscosidadeRESUMO
Size distribution of oil droplets formed in deep water oil and gas blowouts have strong impact on the fate of the oil in the environment. However, very limited data on droplet distributions from subsurface releases exist. The objective of this study has been to establish a laboratory facility to study droplet size versus release conditions (rates and nozzle diameters), oil properties and injection of dispersants (injection techniques and dispersant types). This paper presents this facility (6 m high, 3 m wide, containing 40 m(3) of sea water) and introductory data. Injection of dispersant lowers the interfacial tension between oil and water and cause a significant reduction in droplet size. Most of this data show a good fit to existing Weber scaling equations. Some interesting deviations due to dispersant treatment are further analyzed and used to develop modified algorithms for predicting droplet sizes in a second paper (Johansen et al., 2013).
Assuntos
Modelos Químicos , Poluição por Petróleo , Petróleo/análise , Água do Mar/química , Tensoativos/química , Poluentes Químicos da Água/análiseRESUMO
A large-scale field experiment took place in the marginal ice zone in the Barents Sea in May 2009. Fresh oil (7000 L) was released uncontained between the ice floes to study oil weathering and spreading in ice and surface water. A detailed monitoring of oil-in-water and ice interactions was performed throughout the six-day experiment. In addition, meteorological and oceanographic data were recorded for monitoring of the wind speed and direction, air temperature, currents and ice floe movements. The monitoring showed low concentrations of dissolved hydrocarbons and the predicted acute toxicity indicated that the acute toxicity was low. The ice field drifted nearly 80 km during the experimental period, and although the oil drifted with the ice, it remained contained between the ice floes.