Rapid shipboard measurement of net-collected marine microplastic polymer types using near-infrared hyperspectral imaging.

Isolation and detection of microplastics (MP) in marine samples is extremely cost- and labor-intensive, limiting the speed and amount of data that can be collected. In the current work, we describe rapid measurement of net-collected MPs (net mesh size 300 µm) using a benchtop near-infrared hyperspectral imaging system during a research expedition to the subtropical North Atlantic gyre. Suspected plastic particles were identified microscopically and mounted on a black adhesive background. Particles were imaged with a Specim FX17 near-infrared linescan camera and a motorized stage. A particle mapping procedure was built on existing edge-finding algorithms and a polymer identification method developed using spectra from virgin polymer reference materials. This preliminary work focused on polyethylene, polypropylene, and polystyrene as they are less dense than seawater and therefore likely to be found floating in the open ocean. A total of 27 net tows sampled 2534 suspected MP particles that were imaged and analyzed at sea. Approximately 77.1% of particles were identified as polyethylene, followed by polypropylene (9.2%). A small fraction of polystyrene was detected only at one station. Approximately 13.6% of particles were either other plastic polymers or were natural materials visually misidentified as plastics. Particle size distributions for PE and PP particles with a length greater than 1 mm followed an approximate power law relationship with abundance. This method allowed at-sea, near real-time identification of MP polymer types and particle dimensions, and shows great promise for rapid field measurements of microplastics in net-collected samples.

Helical Plating Compared with Straight Plating and Nailing for Treatment of Proximal Third Humeral Shaft Fractures-A Biomechanical Study.

Background and Objectives: The surgical treatment of proximal humeral shaft fractures usually considers application of either long straight plates or intramedullary nails. By being able to spare the rotator cuff and avoid the radial nerve distally, the implementation of helical plates might overcome the downsides of common fixation methods. The aims of the current study were (1) to explore the biomechanical competence of different plate designs and (2) to compare their performance versus the alternative treatment option of using intramedullary nails. Materials and Methods: Twenty-four artificial humeri were assigned to the following four groups for simulation of an unstable proximal humeral shaft fracture and instrumentation: Group 1 (Straight-PHILOS), Group 2 (MULTILOC-Nail), Group 3 (45°-Helical-PHILOS), and Group 4 (90°-Helical-PHILOS). All specimens underwent non-destructive, quasi-static biomechanical testing under loading in axial compression, torsion in internal/external rotation, and pure bending in four directions, accompanied by motion tracking. Results: Axial stiffness/displacement in Group 2 was significantly higher/smaller than in all other groups (p ≤ 0.010). Torsional displacement in Group 2 was significantly bigger than in all other groups (p ≤ 0.017). Significantly smaller coronal plane displacement was identified in Group 2 versus all other groups (p < 0.001) and in Group 4 versus Group 1 (p = 0.022). Significantly bigger sagittal plane displacement was detected in Group 4 versus all other groups (p ≤ 0.024) and in Group 1 versus Group 2 (p < 0.001). Conclusions: Intramedullary nails demonstrated higher axial stiffness and smaller axial interfragmentary movements compared with all investigated plate designs. However, they were associated with bigger torsional movements at the fracture site. Although 90°-helical plates revealed bigger interfragmentary movements in the sagittal plane, they demonstrated improved resistance against displacements in the coronal plane when compared with straight lateral plates. In addition, 45°-helical plates manifested similar biomechanical competence to straight plates and may be considered a valid alternative to the latter from a biomechanical standpoint.

Iatrogenic Damage to Neurovascular and Soft Tissue Structures During Lateral Release of Hallux Valgus: A Comparative Anatomical Study of Minimally Invasive Versus Open Surgical Techniques.

Lateral release is often an integral step in surgical correction of hallux valgus and can be performed using open or minimally invasive techniques. We investigated whether these techniques cause iatrogenic damage to arteries, nerves, tendons, or joint capsules. In this cadaver study, lateral release was performed on 9 pairs of specimens by a specialized foot surgeon. The specimens were randomly assigned to each group. The operations were followed by anatomical preparation, data collection, photo documentation, and statistical analysis. Iatrogenic damage to arteries, nerves, tendons, or joint capsules was rare, regardless of the surgical technique used. However, with the minimally invasive technique, the tendon of the extensor hallucis longus muscle and the sensitive terminal branches of the fibular nerve were at risk due to their anatomical proximity to the access portal. The deep transverse metatarsal ligament was potentially at risk if the adductor hallucis muscle was completely detached from the lateral sesamoid. When the deep transverse metatarsal ligament was transected there was risk of damaging the underlying plantar neurovascular structures. Both surgical techniques are safe in terms of the risk of injury to neighboring neurovascular and soft tissue structures.

Comparison of Ligament-Repair Techniques for the Syndesmosis: A Simulated Cadaveric Weight-Bearing Computed Tomography Analysis.

Although the literature describes a variety of reconstructive techniques for the syndesmosis, only few studies offer comparative data. Therefore, the authors compared 2 different ligament repair techniques for the syndesmosis. Sixteen paired fresh-frozen human cadaveric lower limbs were embedded in polymethyl methacrylate mid-calf and placed in a custom-made weightbearing simulation frame. Computed tomography scans of each limb were obtained in a simulated foot-flat loading (75N) and single-leg stance (700N) in 5 different foot positions (previously reported data). One of each pair was then reconstructed via 1 of 2 methods: a free medial Achilles tendon autograft or a long peroneal tendon ligament repair. The specimens were rescanned, compared with their respective intact states and directly with each other. Measurements of fibular diastasis, rotation, anteroposterior translation, mediolateral translation, and fibular shortening were performed on the axial cuts of the computed tomography scans, 1 cm proximal to the roof of the plafond. There was no significant difference in fibular positioning with direct comparison of the reconstructions. Comparisons with their respective intact states, however, showed differences in their abilities to control reduction, most notably in the externally rotated and dorsiflexed positions of the foot. Neither reconstruction was clearly superior in restoring physiologic conditions. Only with a comparison of each technique to its respective intact state were differences between the techniques revealed, a benefit of this particular testing method.

Acute atraumatic carpal tunnel syndrome due to flexor tendon rupture following palmar plate osteosynthesis in a patient taking rivaroxaban.

INTRODUCTION: Few case reports describe the development of a hematoma under oral anticoagulation as the cause of an atraumatic carpal tunnel syndrome. CASE REPORT: A 76 years old woman presented an acute atraumatic carpal tunnel syndrome of her left hand under oral anticoagulation with rivaroxaban due to atrial fibrillation. 12 years ago, palmar plate osteosynthesis of a distal radius fracture had been performed on the affected wrist. Open decompression of the carpal canal was performed due to persistent severe pain under intense pain therapy and progressive neurological symptoms. The cause of the pain was a hematoma due to a rupture of the flexor pollicis longus and the second flexor digitorum profundus tendon with concomitant synovitis at the plate's distal rim. After decompression, pain relieved and neurological deficits improved rapidly. DISCUSSION: Ruptures of the flexor tendons occur in palmar plate osteosynthesis in up to 1.5% in the long term postoperative course. Very distal plate positions, like in this case, increase that risk. Under anticoagulation, the rupture induced a hematoma increasing local pressure resulting in an acute carpal tunnel syndrome. Acute nerve compression syndromes should be treated surgically without delay. CONCLUSION: Therapy with anticoagulants may increase hematoma after tendon rupture, thus supporting the development of an atraumatic acute carpal tunnel syndrome and complicating the surgical therapy. Hardware removal after fracture healing should be advised in patients with Soong grade 2 plate positions especially those taking anticoagulants.

Computed Tomography Analysis for Quantification of Displacement of the Distal Fibula in Different Foot Positions With Weightbearing and Sequentially Increased Instability: An Anatomic Cadaveric Study on Syndesmosis.

Syndesmotic injuries are quite common, but accurate diagnosis and treatment can be difficult, in part because of individual anatomic variation and complex movements of the fibula in the incisura. The current cadaveric study was designed to investigate changes in the position of the fibula in the incisura during simulated weightbearing in different foot positions and with sequential sectioning of syndesmotic and deltoid ligaments. Sixteen paired, fresh-frozen cadaveric limbs were embedded in polymethylmethacrylate mid-calf and placed in a weightbearing simulation frame. Computed tomography scans were obtained while the legs were in a simulated foot-flat position (75 N) and single-leg stance (700 N) in 5 foot positions: neutral, 15° external rotation, 15° internal rotation, 20° dorsiflexion, and 20° plantar flexion. The anterior-inferior tibiofibular ligament, posterior tibiofibular ligament complex, deltoid, and interosseous membranes were sectioned sequentially and rescanned. Measurements of fibular diastasis, rotation, anterior-posterior and medial-lateral translation, and fibular shortening were performed. The most destructive state resulted in the largest displacement at the syndesmosis. The degree of subluxation in all ligament states was dependent on the foot position. External rotation created statistically significant displacement at all levels of injury. There were no significant differences between sides of the same donor. Our data demonstrate the importance of foot position in reduction at the syndesmosis under weightbearing. The current ex vivo model could be used to evaluate other aspects of this injury or the value of reconstructive techniques in the future.

Rapid aggregation of biofilm-covered microplastics with marine biogenic particles.

Ocean plastic pollution has resulted in a substantial accumulation of microplastics in the marine environment. Today, this plastic litter is ubiquitous in the oceans, including even remote habitats such as deep-sea sediments and polar sea ice, and it is believed to pose a threat to ecosystem health. However, the concentration of microplastics in the surface layer of the oceans is considerably lower than expected, given the ongoing replenishment of microplastics and the tendency of many plastic types to float. It has been hypothesized that microplastics leave the upper ocean by aggregation and subsequent sedimentation. We tested this hypothesis by investigating the interactions of microplastics with marine biogenic particles collected in the southwestern Baltic Sea. Our laboratory experiments revealed a large potential of microplastics to rapidly coagulate with biogenic particles, which substantiates this hypothesis. Together with the biogenic particles, the microplastics efficiently formed pronounced aggregates within a few days. The aggregation of microplastics and biogenic particles was significantly accelerated by microbial biofilms that had formed on the plastic surfaces. We assume that the demonstrated aggregation behaviour facilitates the export of microplastics from the surface layer of the oceans and plays an important role in the redistribution of microplastics in the oceans.

Bone Mass Distribution of the Distal Tibia in Normal, Osteopenic, and Osteoporotic Conditions: An Ex Vivo Assessment Using HR-pQCT, DXA, and Computational Modelling.

Osteoporosis leads to bone loss and structural deterioration, which increase the risk of fractures. The aim of this study was to characterize the three-dimensional (3D) bone mass distributions of the distal tibia in normal, osteopenic, and osteoporotic conditions. High-resolution peripheral quantitative computed tomography (HR-pQCT) of the 33 % of the distal tibia and local dual-energy X-ray absorptiometry were applied to 53 intact, fresh-frozen tibiae. The HR-pQCTs were graded to assign local T-scores and merged into three equally sized average normal, osteopenic, and osteoporotic surface models. Volumetric bone mineral density (vBMD) was determined using categorized T-scores, volumetric visualization, and virtual bore probes at the dia-, meta-, and epiphyseal sites (T-DIA, T-META, and T-EPI). We observed a distinct 3D bone mass distribution that was gradually uninfluenced by T-score categories. T-DIA was characterized by the lowest bone mass located in the medullary cavity and a wide homogenous cortex containing the maximum vBMD. The T-META showed decreased cortical thickness and maximal vBMD. At the T-EPI, the relatively low vBMD of the mostly trabecular bone was similar to the maximal cortical vBMD in this sub-region. Four trabecular regions of low bone mass were identified in the recesses. The bone content gradually decreased at all sites, whereas the pattern of bone mass distribution remained essentially unchanged, with the exception of disproportionate losses at T-DIA, T-META, and T-EPI that consistently showed increased endocortical, intracortical, and trabecular bone loss. Extra information can be obtained from the specific pattern of bone mass distribution, potential disproportionate bone losses, and method used.

Dynamic locking screw improves fixation strength in osteoporotic bone: an in vitro study on an artificial bone model.

PURPOSE: The novel dynamic locking screw (DLS) was developed to improve bone healing with locked-plate osteosynthesis by equalising construct stiffness at both cortices. Due to a theoretical damping effect, this modulated stiffness could be beneficial for fracture fixation in osteoporotic bone. Therefore, the mechanical behaviour of the DLS at the screw-bone interface was investigated in an artificial osteoporotic bone model and compared with conventional locking screws (LHS). METHODS: Osteoporotic surrogate bones were plated with either a DLS or a LHS construct consisting of two screws and cyclically axially loaded (8,500 cycles, amplitude 420 N, increase 2 mN/cycle). Construct stiffness, relative movement, axial screw migration, proximal (P) and distal (D) screw pullout force and loosening at the bone interface were determined and statistically evaluated. RESULTS: DLS constructs exhibited a higher screw pullout force of P 85 N [standard deviation (SD) 21] and D 93 N (SD 12) compared with LHS (P 62 N, SD 28, p = 0.1; D 57 N, SD 25, p < 0.01) and a significantly lower axial migration over cycles compared with LHS (p = 0.01). DLS constructs showed significantly lower axial construct stiffness (403 N/mm, SD 21, p < 0.01) and a significantly higher relative movement (1.1 mm, SD 0.05, p < 0.01) compared with LHS (529 N/mm, SD 27; 0.8 mm, SD 0.04). CONCLUSION: Based on the model data, the DLS principle might also improve in vivo plate fixation in osteoporotic bone, providing enhanced residual holding strength and reducing screw cutout. The influence of pin-sleeve abutment still needs to be investigated.

Standardized analysis of syndesmosis stability in ankle trauma with an innovative syndesmosis-test-tool: a biomechanical study.

When treating ankle fractures, the question of syndesmosis complex involvement often arises. So far, there is no standardized method to reliably detect syndesmosis injuries in the surgical treatment of ankle fractures. For this reason, an intraoperative syndesmosis-test-tool (STT) was developed and compared to the recommended and established hook-test (HT). Tests were performed on cadaveric lower legs (n = 20) and the diastasis was visualized by 3D camera. Tests were performed at 50, 80, and 100 N in native conditions and four instability levels. Instability was induced from anterior to posterior and the reverse on the opposite side. The impact on diastasis regarding the direction, the force level, the instability level, and the device used was checked using a general linear model for repeated measurement. The direction of the induced instability showed no influence on the diastasis during the stability tests. The diastasis measured with the STT increased from 0.5 to 3.0 mm depending on the instability, while the range was lower with the HT (1.1 to 2.3 mm). The results showed that the differentiation between the instability levels was statistically significantly better for the developed STT. The last level of maximum instability was significantly better differentiable with the STT compared to the HT. An average visualizable diastasis of more than 2 mm could only be achieved at maximum instability. In conclusion, the newly developed STT was superior to the commonly used HT to detect instability.

Fatigue performance of angle-stable tibial nail interlocking screws.

PURPOSE: Tibial nail interlocking screw failure often occurs during delayed fracture consolidation or at early weight bearing of nailed unstable fractures, in general when high implant stress could not be reduced by other means. Is there a biomechanical improvement in long-term performance of angle stable locking screws compared to conventional locking screws for distal locking of intramedullary tibial nails? METHODS: Surrogate bones of human tibiae were cut in the distal third and distal locking of the 10 mm intramedullary tibial nail was performed with either two angle stable locking screws or two conventional locking screws in the mediolateral plane. Six specimens per group were mechanically tested under quasi-static and cyclic axial loading with constantly increasing force. RESULTS: Angle stable locking screw constructs exhibited significantly higher stiffness values (7,809 N/mm ± 647, mean ± SD) than conventional locking screw constructs (6,614 N/mm ± 859, p = 0.025). Angle stable locking screw constructs provided a longer fatigue life, expressed in a significantly higher number of cycles to failure (187,200 ± 18,100) compared to conventional locking screw constructs (128,700 ± 7,000, p = 0.004). CONCLUSION: Fatigue performance of locking screws can be ameliorated by the use of angle stable locking screws, being especially important if the nail acts as load carrier and an improved stability during fracture healing is needed.

Biomechanical performance of different cable and wire cerclage configurations.

PURPOSE: Cerclage technology is regaining interest due to the increasing number of periprosthetic fractures. Different wiring techniques have been formerly proposed and have hibernated over years. Hereby, they are compared to current cerclage technology. METHODS: Seven groups (n = 6) of different cable cerclage (Ø1.7 mm, crimp closure) configurations (one single cerclage looped once around the shells, one single cerclage looped twice, two cerclages each looped once) and solid wire cerclages (Ø1.5 mm, twist closure) (same configurations as cable cerclages, and two braided wires, twisted around each other looped once) fixed two cortical half shells of human femoral shaft mounted on a testing jig. Sinusoidal cyclic loading with constantly increasing force (0.1 N/cycle) was applied starting at 50 N peak load. Cerclage pretension (P), load leading to onset of plastic deformation (D) and load at total failure (T) were identified. Statistical differences between the groups were detected by univariate ANOVA. RESULTS: Double looped cables (P442N ± 129; D1334N ± 319; T2734N ± 330) performed significantly better (p < 0.05) than single looped cables (P292N ± 56; D646N ± 108; T1622N ± 171) and were comparable to two single cables (P392N ± 154; D1191N ± 334; T2675N ± 361). Double looped wires (P335N ± 49; D752N ± 119; T1359N ± 80) were significantly better (p < 0.05) than single looped wires (P181N ± 16; D343N ± 33; T606N ± 109) and performed similarly to single looped cables. Braided wires (P119N ± 26; D225N ± 55; T919N ± 197) exhibited early loss of pretension and plastic deformation. CONCLUSION: Double looped cerclages provided a better fixation stability compared to a single looped cerclage. Double looped wires were comparable to a single looped cable. The use of braided wires could not be recommended mechanically.

Where have all the beads gone? Fate of microplastics in a closed exposure system and their effects on clearance rates in Mytilus spp.

The fate of microplastic particles (MP) in exposure experiments is mostly unclear. We measured the recovery of polystyrene (PS) microbeads, which were applied in various concentrations from 0.07 to 47.47 beads/ml, from the different compartments of an experimental system with mussels (Mytilus spp.). At the end of the experiment, we detected a significant loss of MP indicating that the mussels were exposed to less particles than intended. If such a discrepancy remains un-recognized by the experimenter, observed effects are related to an inaccurate particle concentration. Additionally, we observed reduced clearance rates of the mussels in the presence of MP and the effect size increased with increasing particle concentration. This effect was more pronounced in mussels that had recently spawned than in mussels that still had mature gonads. This is a hint that effects of MP may depend on the reproductive status of an organism.

Spatio-temporal variability in the abundance and composition of beach litter and microplastics along the Baltic Sea coast of Schleswig-Holstein, Germany.

Abundance and composition of beach litter and microplastics (20-5000 µm, excluding fibres) were assessed in spring and autumn 2018 at various beaches along the Baltic Sea coast of Schleswig-Holstein, Northern Germany. The beach litter survey followed the OSPAR guidelines, while microplastics were extracted from sediment samples using density separation and were then identified with Raman µ-spectroscopy. We observed seasonality in the abundance and composition, but not in the mass of beach litter. The median microplastic abundance was 2 particles per 500 g of dry sediment in spring as well as in autumn, while six different synthetic polymers (PE, PP, PS, PET, PVC, POM) were detected. We found no correlation between the abundances of beach litter and microplastics. Our data represent the first systematic co-assessment of macro- and micro beach litter along the Baltic Sea coast of Schleswig-Holstein.

Biomechanical Comparison of Medio-Plantar and Plantar Plate Fixation for First Tarsometatarsal Joint Arthrodesis.

Plantar plate positioning has been demonstrated as biomechanically superior. However, some operators remain resentful about the morbidity of the surgical approach. To provide improved plate fixation for first tarsometatarsal joint arthrodesis with respect to the tibialis anterior tendon, a medio-plantar plate was developed. The purpose of this biomechanical study was to compare its construct stability to that of a plantar plate construct. Twelve pairs of fresh frozen human specimens were used in a matched pair test. Each pair was fixed with a 4 mm compression screw and either a plantar locking plate or a medio-plantar locking plate. A cantilever beam test was performed in dorsiflexion. Before and after cyclic loading (5000 cycles; 40 N), bending stiffness and relative movements at the joint space were monitored in a quasi-static test including optical motion tracking. Maximum load and bending moment to failure were investigated in a load-to-failure ramp test. The bending stiffness of both groups did not significantly differ before (plantar 49.9 N/mm ± 19.2; medio-plantar 53.9 N/mm ± 25.4, p = 0.43) or after (plantar 24.4 N/mm ± 9.7; medio-plantar 35.3 N/mm ± 22.0, p = 0.08) cyclic loading but decreased significantly in both groups (p < 0.01) after cyclic loading. Relative movement increased significantly during cyclic testing in both groups (p < 0.01) but did not differ significantly between the groups before (p = 0.29) or after (p = 0.16) cyclic loading. Neither load nor bending moment to failure were significantly different (plantar 225 N ± 78, 10.8 Nm; medio-plantar 210 N ± 86, 10.1 Nm, p = 0.61). Both plate constructs provided equivalent construct stability, both being well suited for Lapidus arthrodesis.

The locking attachment plate for proximal fixation of periprosthetic femur fractures--a biomechanical comparison of two techniques.

PURPOSE: Mechanical properties of a locking attachment plate construct (LAP-LCP), allowing bicortical screw placement laterally to the prosthesis stem, are compared to a cerclage-LCP construct. METHODS: Eight right synthetic femora with implanted uncemented hip endoprosthesis were cut distally and fixed with LCP, monocortical locking screws and either LAP (n = 4) or cerclage (n = 4). Cyclic testing was performed with monotonically increasing sinusoidal load until failure. Relative movements at the plate-femur interface were registered by motion tracking. Statistical differences were detected by unpaired t-test and general linear model repeated measures. RESULTS: Stiffness of the LAP-LCP was significantly higher at the beginning (875.4 N/mm ± 29.8) and after 5000 cycles (1213.0 N/mm ± 101.1) compared to the cerclage-LCP (644.96 N/mm ± 50.1 and 851.9 N/mm ± 81.9), with p = 0.013. Relative movements for AP-bending (B) and axial translation (T) of the LAP-LCP at the beginning (0.07° ± 0.02, 0.20 mm ± 0.08), after 500 cycles (0.16° ± 0.10, 0.26 mm ± 0.07) and after 5000 cycles (0.26° ± 0.11, 0.31 mm ± 0.07) differed significantly from the cerclage-LCP (beg.: 0.26° ± 0.04, 0.28 mm ± 0.05; 500 cyc: 0.47° ± 0.03, 0.53 mm ± 0.07; 5000 cyc.: 0.63° ± 0.18, 0.79 mm ± 0.13), with B: p = 0.02, T: p = 0.04. Relative movements for medial bending were not significantly different between the two constructs. Cycles to failure (criterion 1 mm axial translation) differed significantly between LAP-LCP (19,519 ± 1,758) and cerclage-LCP (11,265 ± 2,472), with p = 0.035. CONCLUSIONS: Biomechanically, the LAP-LCP construct improves proximal fixation of periprosthetic fractures compared to the cerclage-LCP construct.

Underneath the cerclage: an ex vivo study on the cerclage-bone interface mechanics.

INTRODUCTION: Cerclages regain interest due to a rising number of periprosthetic fractures. The contact distribution at the circumferential cerclage-bone interface is still unknown. Local interface pressure depends on the amount of contact area. Cortical damage at the interface would provoke cerclage loosening. Therefore, the contact area, the bone pressure along the interface and the cortical resistance underneath loaded cerclages were determined in an ex vivo model. MATERIALS AND METHODS: Human diaphyseal femoral bone was used with differing cross-sectional geometry. Bone contact points of fixed 1.5 mm wire and 1.7 mm cable cerclages were identified from axial radiographs. Pressure distribution at the cerclage-bone interface was recorded with a pressure-measuring film using a distraction setup with two cortical half shells. Bone shells with installed cerclages were separated with up to 400 N force and were subsequently analyzed histologically to detect cortical damage. RESULTS: Both cerclage types exhibited a point contact fixation with non-loaded spanned zones in-between. Cables cover larger contact areas. Both cerclages exhibited an inhomogeneous interface pressure distribution depending on the bone surface geometry. Histology revealed intact cortical bone without cortical affection after loading of both cerclage types. CONCLUSION: Point contact fixation of the cerclages installs non-loaded, spanned zones where the periosteum is not compressed, rendering a strangulation of the blood supply unlikely. Cortical bone withstands static concentric pressure produced by the cerclage. Cortical groove formation is attributed to instability under functional load and not to weakness of the cortex itself.

Angulated locking plate in periprosthetic proximal femur fractures: biomechanical testing of a new prototype plate.

INTRODUCTION: To improve proximal plate fixation of periprosthetic femur fractures, a prototype locking plate with proximal posterior angulated screw positioning was developed and biomechanically tested. METHODS: Twelve fresh frozen, bone mineral density matched human femora, instrumented with cemented hip endoprosthesis were osteotomized simulating a Vancouver B1 fracture. Specimens were fixed proximally with monocortical (LCP) or angulated bicortical (A-LCP) head-locking screws. Biomechanical testing comprised quasi-static axial bending and torsion and cyclic axial loading until catastrophic failure with motion tracking. RESULTS: Axial bending and torsional stiffness of the A-LCP construct were (1,633 N/mm ± 548 standard deviation (SD); 0.75 Nm/deg ± 0.23 SD) at the beginning and (1,368 N/mm ± 650 SD; 0.67 Nm/deg ± 0.25 SD) after 10,000 cycles compared to the LCP construct (1,402 N/mm ± 272 SD; 0.54 Nm/deg ± 0.19 SD) at the beginning and (1,029 N/mm ± 387 SD; 0.45 Nm/deg ± 0.15) after 10,000 cycles. Relative movements for medial bending and axial translation differed significantly between the constructs after 5,000 cycles (A-LCP 2.09° ± 0.57 SD; LCP 5.02° ± 4.04 SD; p = 0.02; A-LCP 1.25 mm ± 0.33 SD; LCP 2.81 mm ± 2.32 SD; p = 0.02) and after 15,000 cycles (A-LCP 2.96° ± 0.70; LCP 6.52° ± 2.31; p = 0.01; A-LCP 1.68 mm ± 0.32; LCP 3.14 mm ± 0.68; p = 0.01). Cycles to failure (criterion 2 mm axial translation) differed significantly between A-LCP (15,500 ± 2,828 SD) and LCP construct (5,417 ± 7,236 SD), p = 0.03. CONCLUSION: Bicortical angulated screw positioning showed less interfragmentary osteotomy movement and improves osteosynthesis in periprosthetic fractures.

[Cement augmentation and bone graft substitutes-Materials and biomechanics]. / Zementaugmentation und Knochenersatz ­ Materialien und Biomechanik.

BACKGROUND: Materials with different characteristics are used for cement augmentation and as bone graft substitutes. OBJECTIVE: Cement augmentation and bone graft substitutes are the subject of current research. The evaluation of new knowledge allows its specific application. MATERIAL AND METHODS: Selective literature search and outline of experimental research results on cement augmentation and bone graft substitutes. RESULTS: Augmentation and bone graft substitutes are essential components of current trauma surgical procedures. Despite intensive research all materials have specific disadvantages. Cement augmentation of implants enhances not only the anchorage but also influences the failure mode. CONCLUSION: Cement augmentation has large potential especially in osteoporotic bone. In load-bearing regions acrylic-based cements remain the standard of choice. Ceramic cements are preferred in non-load-bearing areas. Their combination with resorbable metals offers still largely unexplored potential. Virtual biomechanics can help improve the targeted application of cement augmentation.

Abundance, composition and sources of beach litter on the Cape Verdean island São Vicente.

This study represents the first assessment of beach litter on an island of the west African archipelagic state of Cape Verde. On five beaches of São Vicente, litter was collected along transects and classified according to the OSPAR protocol, with the Matrix Scoring Technique used to allocate it to four sources. Beach litter on São Vicente is highly variable in both amount and composition, while land- and sea-based sources contribute to litter loads to different extents depending on the use and geographic orientation of the beach. Four of the five surveyed beaches exhibited litter loads that were similar to pollution levels previously described for other oceanic islands, while a north-eastern-facing beach featured exceptionally high loads. This was presumably because it receives litter from distant sources due to its exposure to a major ocean surface current.