Metal-Insulator-Semiconductor Diode Consisting of Two-Dimensional Nanomaterials.

We present a novel metal-insulator-semiconductor (MIS) diode consisting of graphene, hexagonal BN, and monolayer MoS2 for application in ultrathin nanoelectronics. The MIS heterojunction structure was fabricated by vertically stacking layered materials using a simple wet chemical transfer method. The stacking of each layer was confirmed by confocal scanning Raman spectroscopy and device performance was evaluated using current versus voltage (I-V) and photocurrent measurements. We clearly observed better current rectification and much higher current flow in the MIS diode than in the p-n junction and the metal-semiconductor diodes made of layered materials. The I-V characteristic curve of the MIS diode indicates that current flows mainly across interfaces as a result of carrier tunneling. Moreover, we observed considerably high photocurrent from the MIS diode under visible light illumination.

Ultrahigh Photosensitivity Based on Single-Step Lay-on Integration of Freestanding Two-Dimensional Transition-Metal Dichalcogenide.

Two-dimensional transition-metal dichalcogenides have attracted significant attention because of their unique intrinsic properties, such as high transparency, good flexibility, atomically thin structure, and predictable electron transport. However, the current state of device performance in monolayer transition-metal dichalcogenide-based optoelectronics is far from commercialization, because of its substantial strain on the heterogeneous planar substrate and its robust metal deposition, which causes crystalline damage. In this study, we show that strain-relaxed and undamaged monolayer WSe2 can improve a device performance significantly. We propose here an original point-cell-type photodetector. The device consists in a monolayer of an absorbing TMD (i.e., WSe2) simply deposited on a structured electrode, i.e., core-shell silicon-gold nanopillars. The maximum photoresponsivity of the device is found to be 23.16 A/W, which is a significantly high value for monolayer WSe2-based photodetectors. Such point-cell photodetectors can resolve the critical issues of 2D materials, leading to tremendous improvements in device performance.

Characterizations of Ohmic and Schottky-behaving contacts of a single ZnO nanowire.

Current-voltage and Kelvin probe force microscopy (KPFM) measurements were performed on single ZnO nanowires. Measurements are shown to be strongly correlated with the contact behavior, either Ohmic or diode-like. The ZnO nanowires were obtained by metallo-organic chemical vapor deposition (MOCVD) and contacted using electronic-beam lithography. Depending on the contact geometry, good quality Ohmic contacts (linear I-V behavior) or non-linear (diode-like) contacts were obtained. Current-voltage and KPFM measurements on both types of contacted ZnO nanowires were performed in order to investigate their behavior. A clear correlation could be established between the I-V curve, the electrical potential profile along the device and the nanowire geometry. Some arguments supporting this behavior are given based on technological issues and on depletion region extension. This work will help to better understand the electrical behavior of Ohmic contacts on single ZnO nanowires, for future applications in nanoscale field-effect transistors and nano-photodetectors.

Waveguide-coupled nanowire as an optical antenna.

We study the optical coupling between a gold nanowire and a silver ion-exchanged waveguide, with special emphasis on the nanowire antenna radiation pattern. We measure the radiation patterns of waveguide-coupled gold nanowires with a height of 70 nm and width of 50 or 150 nm in the 450-700 nm spectral range for TE and TM polarizations. We perform a systematic theoretical study on the wavelength, polarization, nanowire size, and material dependences on the properties of the radiation pattern. We also give some elements concerning absorption and near-field. Experiments and calculations show localized plasmon resonance for the polarization orthogonal to the wire (far-field resonance at 580 nm for the smallest wire and 670 nm for the widest). It is shown that a great variety of radiation patterns can be obtained, together with a high sensitivity to a change of one parameter, particularly near-resonance.

A review of cost-effective black silicon fabrication techniques and applications.

Ever since the discovery of black silicon, scientists around the world have been trying to come up with novel, cost-effective methods of utilizing this super material in a variety of different industries due to its remarkably low reflectivity and excellent electronic and optoelectronic properties. In this review, many of the most common methods of black silicon fabrication are exhibited, including metal-assisted chemical etching, reactive ion etching, and femto-second laser irradiation. Different nanostructured silicon surfaces are assessed based on their reflectivity and applicable properties in both the visible wavelength range and the infrared range. The most cost efficient technique for the mass production of black silicon is discussed, as well as some promising contender materials ready to replace silicon. Also, solar cell, IR photo-detector, and antibacterial applications are looked into, along with their respective challenges to date.

Multiplexed Gas Sensor: Fabrication Strategies, Recent Progress, and Challenges.

Due to miscellaneous toxic gases in the vicinity, there is a burgeoning need for advancement in the existing gas sensing technology not only for the survival of mankind but also for the industries based in various fields such as beverage, forestry, health care, environmental monitoring, agriculture, and military security. A gas sensor must be highly selective toward a specific gas in order to avoid incorrect signals while responding to nontarget gases. This may lead to complex scenarios depicting sensor defects, such as low selectivity and cross-sensitivity. Therefore, a multiplex gas sensor is required to address the problems of cross selectivity by combining different gas sensors, signal processing, and pattern recognition techniques along with the currently employed gas sensing technologies. The different sensing materials used in these sensor arrays will produce a unique response signal for developing a set of identifiers as the input that can be used to recognize a specific gas by its "fingerprint". This review provides a comprehensive review of chemiresistive-based multiplex gas sensors, including various fabrication strategies from expensive to low-cost techniques, advances in sensing materials, and a gist of various pattern recognition techniques used for both rigid and flexible gas sensor applications. Finally, the review assesses the current state-of-the-art in multiplex gas sensor technology and discusses various challenges for future research in this direction.

Stabilization of Copper-Based Biochips with Alumina for Biosensing Application.

Surface plasmon resonance devices typically rely on the use of gold-coated surfaces, but the use of more abundant metals is desirable for the long-term development of plasmonic biochips. As a substitute for gold, thin copper films have been deposited on glass coverslips by thermal evaporation. As expected, these films immersed in a water solution initially exhibit an intense plasmonic resonance comparable to gold. However, without protection, an angle-resolved optical analysis shows a rapid degradation of the copper, characterized by a continuous angular shift of the plasmonic resonance curve. We show that copper films protected with a thin layer of aluminum oxide of a few nanometers can limit the oxidation rate for a sufficient time to perform some standard measurements. As the process is simple and compatible with the current biochip production technique, such an approach could pave the way for the production of alternative and more sustainable biochips.

Sensitivity Enhancement of Hybrid Two-Dimensional Nanomaterials-Based Surface Plasmon Resonance Biosensor.

In this work, we designed structures based on copper nanosubstrate with graphene and two-dimensional transition metal dichalcogenides (TMDC) in order to achieve an ultrasensitive surface plasmon resonance biosensor. This system contains seven components: SF11 triangular prism, BK-7 glass, Chromium (Cr) adhesion layer, thin copper film, layers of one of the types of transition metal dichalcogenides: MoS2, MoSe2, WS2 or WSe2 (defined as MX2), graphene, sensing layer with biomolecular analyte. Copper was chosen as a plasmonic material because it has a higher conductivity than gold which is commonly used in plasmonic sensors. Moreover, copper is a cheap and widespread material that is easy to produce on a large scale. We have carried out both theoretical and numerical sensitivity calculations of these kinds of structures using the Goos-Hänchen (GH) shift method. GH shift is lateral position displacement of the p-polarized reflected beam from a boundary of two media having different indices of refraction under total internal reflection condition and its value can be retrieved from the phase change of the beam. The SPR signal based on the GH shift is much more sensitive compared to other methods, including angular and wavelength scanning, due to much more abrupt phase change of the SPR reflected light than its intensity ones. By optimizing the parameters of the SPR sensing substrate, such as thickness of copper, number of layers of 2D materials and excitation wavelength, we theoretically showed an enhanced sensitivity with a detection limit 10-9 refractive index unit (RIU).

Selective separation of plastic LED lamp components using electrodynamic fragmentation for material recovery.

The recycling of light-emitting diode (LED) lamps and tubes is becoming increasingly important due to their growing market share as energy-efficient lighting technology. Here we report on the use of high voltage electric-pulse fragmentation to recover elementary components such as LED chips and printed circuit boards (drivers). E27 LED lamps with plastic bulbs, which represent 48% of deposits collected by a French company, are used as a case study. More than 150 lamps were tested on a laboratory reactor for electrodynamic fragmentation. The technological process in which highly energetic electrical pulses were applied to materials immersed in water was studied in order to separate the components of the LED lamps using a minimal specific energy. The estimated energy necessary to achieve total separation assessed at 64%, without grinding pretreatment, was 5.2 ± 0.6 kWh per ton, representing a mass recycling rate of 74%. Based on the disassembled material, the commercial value of the recovered materials was thus estimated. Gold, as the most representative material, was found to represent 0.03% of the mass fraction for 83.6% of the total commercial value. The process disassembling capacity is a key issue to increase the recycling rate of current LED lamps and tubes.

Surface Functionalization with Polymer Membrane or SEIRA Interface to Improve the Sensitivity of Chalcogenide-Based Infrared Sensors Dedicated to the Detection of Organic Molecules.

Priority substances likely to pollute water can be characterized by mid-infrared spectroscopy based on their specific absorption spectral signature. In this work, the detection of volatile aromatic molecules in the aqueous phase by evanescent-wave spectroscopy has been optimized to improve the detection efficiency of future in situ optical sensors based on chalcogenide waveguides. To this end, a hydrophobic polymer was deposited on the surface of a zinc selenide prism using drop and spin-coating methods. To ensure that the water absorption bands will be properly attenuated for the selenide waveguides, two polymers were selected and compared: polyisobutylene and ethylene/propylene copolymer coating. The system was tested with benzene, toluene, and ortho-, meta-, and para-xylenes at concentrations ranging from 10 ppb to 40 ppm, and the measured detection limit was determined to be equal to 250 ppb under these analytical conditions using ATR-FTIR. The polyisobutylene membrane is promising for pollutant detection in real waters due to the reproducibility of its deposition on selenide materials, the ease of regeneration, the short response time, and the low ppb detection limit, which could be achieved with the infrared photonic microsensor based on chalcogenide materials. To improve the sensitivity of future infrared microsensors, the use of metallic nanostructures on the surface of chalcogenide waveguides appears to be a relevant way, thanks to the plasmon resonance phenomena. Thus, in addition to preliminary surface-enhanced infrared absorption tests using these materials and a functionalization via a self-assembled monolayer of 4-nitrothiophenol, heterostructures combining gold nanoparticles/chalcogenide waveguides have been successfully fabricated with the aim of proposing a SEIRA microsensor device.

Two-dimensional displacement measurement by quasi-common-optical-path heterodyne grating interferometer.

A method based on a specific quasi-common-optical-path (QCOP) configuration for two-dimensional displacement measurement is presented. The measurement system consists of a heterodyne light source, two-dimensional holographic grating, specially designed set of half wave plates, and lock-in amplifiers. Two measurement configurations, for single and differential detection, are designed. The sensitivity, resolution and nonlinear phase error of the differential detection type are better than those of the single detection type. The experimental results demonstrate that the QCOP interferometer has the ability to measure two-dimensional displacement while maintaining high system stability.

Implementation of PT symmetric devices using plasmonics: principle and applications.

The so-called PT symmetric devices, which feature ε((-x)) = ε((x))* associated with parity-time symmetry, incorporate both gain and loss and can present a singular eigenvalue behaviour around a critical transition point. The scheme, typically based on co-directional coupled waveguides, is here transposed to the case of variable gain on one arm with fixed losses on the other arm. In this configuration, the scheme exploits the full potential of plasmonics by making a beneficial use of their losses to attain a critical regime that makes switching possible with much lowered gain excursions. Practical implementations are discussed based on existing attempts to elaborate coupled waveguide in plasmonics, and based also on the recently proposed hybrid plasmonics waveguide structure with a small low-index gap, the PIROW (Plasmonic Inverse-Rib Optical Waveguide).

Heterodyne grating interferometer based on a quasi-common-optical-path configuration for a two-degrees-of-freedom straightness measurement.

We present a heterodyne grating interferometer based on a quasi-common-optical-path (QCOP) design for a two-degrees-of-freedom (DOF) straightness measurement. Two half-wave plates are utilized to rotate the polarizations of two orthogonally polarized beams. The grating movement can be calculated by measuring the phase difference variation in each axis. The experimental results demonstrate that our method has the ability to measure two-DOF straightness and still maintain high system stability. The proposed and demonstrated method, which relies on heterodyne interferometric phase measurement combined with the QCOP configuration, has the advantages of high measurement resolution, relatively straightforward operation, and high system stability.

Efficient directional coupling between silicon and copper plasmonic nanoslot waveguides: toward metal-oxide-silicon nanophotonics.

Coupling plasmonics and silicon photonics is the best way to bridge the size gap between macroscopic optics and nanodevices in general and especially nanoelectronic devices. We report on the realization of key blocks for future plasmonic planar integrated optics, nano-optical couplers, and nanoslot waveguides that are compatible both with the silicon photonics and the CMOS microelectronics. Copper-based devices provide for very efficient optical coupling, unexpectedly low propagation losses and a broadband sub-50 nm optical confinement. The fabrication in a standard frontline microelectronic facilities hints broad possibilities of hybrid opto-electronic very large scale integration.

Bidimensional near-field sampling spectrometry.

We report on a concept of compact optical Fourier-transform spectrometer based on bidimensional (2D) spatial sampling of a confined interferogram. The spectrometer consists of a nanostructured glass surface on which two light beams interfere in total internal reflection. Subwavelength spatial sampling of the interferogram near field is achieved by introducing a tilt angle between a 2D array of optical nanoantennas and the interferogram pattern. The intensity distribution of the scattered light is recorded on a 2D CCD camera, and a one-dimensional Fourier transform of the interferogram is used to recover the input light spectrum. Experimental results show a wide spectral bandwidth in the visible range, down to 380 nm, with spectral resolution of 1.6 nm around 780 nm.

Real-space observation of spectral degeneracy breaking in a waveguide-coupled disk microresonator.

We report on the real-space observation of resonant frequency splitting in a high-Q waveguide-coupled silicon-on-insulator microdisk resonator. Phase sensitive near-field analysis reveals the stationary nature of the two resonant states, and spectral investigations clearly show their orthogonality. These measurements emphasize the role of the coupling waveguide in this splitting phenomenon. The symmetry of the two stationary whispering gallery modes is clearly observed and is found to follow the axial symmetry of the waveguide-coupled microdisk as it has been reported by earlier theoretical predictions.

Correction: Facile, wafer-scale compatible growth of ZnO nanowires via chemical bath deposition: assessment of zinc ion contribution and other limiting factors.

[This corrects the article DOI: 10.1039/D0NA00434K.].

Facile, wafer-scale compatible growth of ZnO nanowires via chemical bath deposition: assessment of zinc ion contribution and other limiting factors.

ZnO is a highly promising, multifunctional nanomaterial having various versatile applications in the fields of sensors, optoelectronics, photovoltaics, photocatalysts and water purification. However, the real challenge lies in producing large scale, well-aligned, highly reproducible ZnO nanowires (NWs) using low cost techniques. This large-scale production of ZnO NWs has stunted the development and practical usage of these NWs in fast rising fields such as photocatalysis or in photovoltaic applications. The present article shows an effective, simple approach for the uniform, aligned growth of ZnO NWs on entire silicon wafers (sizes 3 or 4 inches), using a low-temperature Chemical Bath Deposition (CBD) technique. In addition to this, a systematic study of the substrate size dependent growth of NWs has been conducted to better understand the effect of the limitation in the deposition rate of Zn2+ ions on the growth of NWs. The growth rate of ZnO NWs is seen to have a strong relationship with the substrate size. Also, the loading efficiency of the Zn2+ ions is higher in ZnO NWs grown on a 3-inch silicon wafer in comparison to those grown on a small piece. An in-depth time dependent growth study conducted on entire 3-inch wafers to track the morphological evolution (length, diameter and number of the NWs) reveals that the growth rate of the length of the NWs reaches a saturation state in a short time span of 20 min. Assessment of the overall homogeneity of the NWs grown on the 3-inch wafer and simultaneous growth on two entire 4-inch silicon wafers has also been demonstrated in this article. This demonstration of large-scale, well-aligned controllable, aligned growth of ZnO NWs on entire silicon wafers is a first step towards NW based devices especially for applications such as photovoltaic, water purification, photocatalysis or biomedical applications.

Giant defect emission enhancement from ZnO nanowires through desulfurization process.

Zinc oxide (ZnO) is a stable, direct bandgap semiconductor emitting in the UV with a multitude of technical applications. It is well known that ZnO emission can be shifted into the green for visible light applications through the introduction of defects. However, generating consistent and efficient green emission through this process is challenging, particularly given that the chemical or atomic origin of the green emission in ZnO is still under debate. In this work we present a new method, for which we coin term desulfurization, for creating green emitting ZnO with significantly enhanced quantum efficiency. Solution grown ZnO nanowires are partially converted to ZnS, then desulfurized back to ZnO, resulting in a highly controlled concentration of oxygen defects as determined by X-ray photoelectron spectroscopy and electron paramagnetic resonance. Using this controlled placement of oxygen vacancies we observe a greater than 40-fold enhancement of integrated emission intensity and explore the nature of this enhancement through low temperature photoluminescence experiments.

Refractive index mediated plasmon hybridization in an array of aluminium nanoparticles.

The arrangement of plasmonic nanoparticles in a non-symmetrical environment can feature far-field and/or near-field interactions depending on the distance between the objects. In this work, we study the hybridization of three intrinsic plasmonic modes (dipolar, quadrupolar and hexapolar modes) sustained by one elliptical aluminium nanocylinder, as well as behavior of the hybridized modes when the nanoparticles are organized in arrays or when the refractive index of the surrounding medium is changed. The position and the intensity of these hybridized modes were shown to be affected by the near-field and far-field interactions between the nanoparticles. In this work, two hybridized modes were tuned in the UV spectral range to spectrally coincide with the intrinsic interband excitation and emission bands of ZnO nanocrystals. The refractive index of the ZnO nanocrystal layer influences the positions of the plasmonic modes and increases the role of the superstrate medium, which in turn results in the appearance of two separate modes in the small spectral region. Hence, the enhancement of ZnO nanocrystal photoluminescence benefits from the simultaneous excitation and emission enhancements.