Bio-based ether solvent and ionic liquid electrolyte for sustainable sodium-air batteries.

Sodium-air batteries (SABs) are receiving considerable attention for the development of next generation battery alternatives due to their high theoretical energy density (up to 1105 W h kg-1). However, most of the studies on this technology are still based on organic solvents; in particular, diglyme, which is highly flammable and toxic for the unborn child. To overcome these safety issues, this research investigates the first use of a branched ether solvent 1,2,3-trimethoxypropane (TMP) as an alternative electrolyte to diglyme for SABs. Through this work, the reactivity of the central tertiary carbon in TMP towards bare sodium metal was identified, while the addition of N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ([C4mpyr][TFSI]) as a co-solvent proved to be an effective strategy to limit the reactivity. Moreover, a Na-ß-alumina disk was employed for anode protection, to separate the TMP-based electrolyte from the sodium metal. The new cell design resulted in improved cell performance: discharge capacities of up to 1.92 and 2.31 mA h cm-2 were achieved for the 16.6 mol% NaTFSI in TMP and 16.6 mol% NaTFSI in TMP/[C4mpyr][TFSI] compositions, respectively. By means of SEM, Raman and 23Na NMR techniques, NaO2 cubes were identified to be the major discharge product for both electrolyte compositions. Moreover, the hybrid electrolyte was shown to hinder the formation of side-products during discharge - the ratio of NaO2 to side-products in the hybrid electrolyte was 2.4 compared with 0.8 for the TMP-based electrolyte - and a different charge mechanism for the dissolution of NaO2 cubes for each electrolyte was observed. The findings of this work demonstrate the high potential of TMP as a base solvent for SABs, and the importance of careful electrolyte composition design in order to step towards greener and less toxic batteries.

Fast Visible-Light 3D Printing of Conductive PEDOT:PSS Hydrogels.

Functional inks for light-based 3D printing are actively being searched for being able to exploit all the potentialities of additive manufacturing. Herein, a fast visible-light photopolymerization process is showed of conductive PEDOT:PSS hydrogels. For this purpose, a new Type II photoinitiator system (PIS) based on riboflavin (Rf), triethanolamine (TEA), and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is investigated for the visible light photopolymerization of acrylic monomers. PEDOT:PSS has a dual role by accelerating the photoinitiation process and providing conductivity to the obtained hydrogels. Using this PIS, full monomer conversion is achieved in less than 2 min using visible light. First, the PIS mechanism is studied, proposing that electron transfer between the triplet excited state of the dye (3 Rf*) and the amine (TEA) is catalyzed by PEDOT:PSS. Second, a series of poly(2-hydroxyethyl acrylate)/PEDOT:PSS hydrogels with different compositions are obtained by photopolymerization. The presence of PEDOT:PSS negatively influences the swelling properties of hydrogels, but significantly increases its mechanical modulus and electrical properties. The new PIS is also tested for 3D printing in a commercially available Digital Light Processing (DLP) 3D printer (405 nm wavelength), obtaining high resolution and 500 µm hole size conductive scaffolds.

The Effects of Mono- and Bivalent Linear Alkyl Interlayer Spacers on the Photobehavior of Mn(II)-Based Perovskites.

Mn(II)-based perovskite materials are being intensively explored for lighting applications; understanding the role of ligands regarding their photobehavior is fundamental for their development. Herein, we report on two Mn (II) bromide perovskites using monovalent (perovskite 1, P1) and bivalent (perovskite 2, P2) alkyl interlayer spacers. The perovskites were characterized with powder X-ray diffraction (PXRD), electron spin paramagnetic resonance (EPR), steady-state, and time-resolved emission spectroscopy. The EPR experiments suggest octahedral coordination in P1 and tetrahedral coordination for P2, while the PXRD results demonstrate the presence of a hydrated phase in P2 when exposed to ambient conditions. P1 exhibits an orange-red emission, while P2 shows a green photoluminescence, as a result of the different types of coordination of Mn(II) ions. Furthermore, the P2 photoluminescence quantum yield (26%) is significantly higher than that of P1 (3.6 %), which we explain in terms of different electron-phonon couplings and Mn-Mn interactions. The encapsulation of both perovskites into a PMMA film largely increases their stability against moisture, being more than 1000 h for P2. Upon increasing the temperature, the emission intensity of both perovskites decreases without a significant shift in the emission spectrum, which is explained in terms of an increase in the electron-phonon interactions. The photoluminescence decays fit two components in the microsecond regime-the shortest lifetime for hydrated phases and the longest one for non-hydrated phases. Our findings provide insights into the effects of linear mono- and bivalent organic interlayer spacer cations on the photophysics of these kinds of Mn (II)-based perovskites. The results will help in better designs of Mn(II)-perovskites, to increase their lighting performance.

H(N3)dap (Hdap = 2,6-Diaminopurine) Recognition by Cu2(EGTA): Structure, Physical Properties, and Density Functional Theory Calculations of [Cu4(µ-EGTA)2(µ-H(N3)dap)2(H2O)2]·7H2O.

Reactions in water between the Cu2(µ-EGTA) chelate (EGTA = ethylene-bis(oxyethyleneimino)tetraacetate(4-) ion) and Hdap in molar ratios 1:1 and 1:2 yield only blue crystals of the ternary compound [Cu4(µ-EGTA)2(µ-H(N3)dap)2(H2O)2]·7H2O (1), which has been studied via single-crystal X-ray diffraction and various physical methods (thermal stability, spectral and magnetic properties), as well as DFT theoretical calculations. In the crystal, uncoordinated water is disordered. The tetranuclear complex molecule also has some irrelevant disorder in an EGTA-ethylene moiety. In the complex molecule, both bridging organic molecules act as binucleating ligands. There are two distorted five- and two six-coordinated Cu(II) centers. Each half of EGTA acts as a tripodal tetradentate Cu(II) chelator, with a mer-NO2 + O(ether, distal) conformation. Hdap exhibits the tautomer H(N3)dap, with the dissociable H-atom on its less basic N-heterocyclic atom. These features favor the efficient cooperation between Cu-N7 or Cu-N9 bonds with appropriate O-EGTA atoms, as N6-H···O or N3-H···O interligand interactions, respectively. The bridging role of both organics determines the tetranuclear dimensionality of the complex. In this crystal, such molecules associate in zig-zag chains built by alternating π-π interactions between the five- or six-atom rings of Hdap ligands of adjacent molecules. DFT theoretical calculations (using two different theoretical models and characterized by the quantum theory of "atoms in molecules") reveal the importance of these π-π interactions between Hdap ligands, as well as those corresponding to the referred hydrogen bonds in the contributed tetranuclear molecule.

Consecutive Single-Crystal-to-Single-Crystal Isomerization of Novel Octamolybdate Anions within a Microporous Hybrid Framework with Robust Water Sorption Properties.

The 3D hybrid framework [{Cu(cyclam)}3 (κ-Mo8 O27 )] ⋅ 14H2 O (1) (cyclam=1,4,8,11-tetraazacyclotetradecane) undergoes sequential single-crystal-to-single-crystal transformations upon heating to afford two different anhydrous phases (2 a and 3 a). These transitions modify the framework dimensionality and enable the isomerization of κ-octamolybdate (κ-Mo8 ) anions into λ (2 a) and µ (3 a) forms through metal migration. Hydration of 3 a involves condensation of one water molecule to the cluster to afford the γ-Mo8 isomer in 4, which dehydrates back into 3 a through the 6 a intermediate. In contrast, 2 a reversibly hydrates to form 5, exhibiting the same Mo8 cluster as that of 1. It is remarkable that three of the Mo8 clusters (κ, λ and µ) are new and that up to three different microporous phases can be isolated from 1 (2 a, 3 a, and 6 a). Water vapor sorption analyses show high recyclability and the highest uptake values for POM-based systems. The isotherms display an abrupt step at low humidity level desirable for humidity control devices or water harvesting in drylands.

Slow Magnetic Relaxation and Luminescent Properties of Mononuclear Lanthanide-Substituted Keggin-Type Polyoxotungstates with Compartmental Organic Ligands.

The reaction of mid to late lanthanide ions with the N,N'-dimethyl-N,N'-bis(2-hydroxy-3-formyl-5-bromobenzyl)ethylene-diamine organic ligand and monolacunary Keggin type [α-SiW11O39]8- anion affords a series of isostructural compounds, namely, K5[LnIII(α-SiW11O39)(C20H22Br2N2O4)]·14H2O (1-Ln, Ln = Sm to Lu). The molecular structure of these sandwich-type complexes is formed by the LnIII ion in a biaugmented trigonal prismatic geometry, which occupies the external O4 site of the organic ligand and the vacant site of the lacunary polyoxometalate (POM) unit. The empty N2O2 coordination site of the organic ligand allows its unprecedented folding, which displays a relative perpendicular arrangement of aromatic groups. Weak Br···Br and π-π interactions established between adjacent molecular units govern the crystal packing, which results in the formation of assemblies containing six hybrid species assembled in a chairlike conformation. 1-Gd and 1-Yb display slow relaxation of the magnetization after the application of an external magnetic field with maxima in the out-of-phase magnetic susceptibility plots below ∼5-6 K, which is ascribed to the presence of various relaxation mechanisms. Moreover, photoluminescent emission is sensitized for 1-Sm and 1-Eu in the visible region and 1-Er and 1-Yb in the NIR. In contrast, the quenching of metal-centered luminescence in the 1-Tb derivative has been attributed to the out-of-pocket coordination mode of the lanthanide center within the POM fragment. It is demonstrated that the 1-Yb dual magneto-luminescent material represents the first lanthanide-containing POM reported to date with simultaneous slow magnetic relaxation and NIR emission. Solution stability of the hybrid molecular species in water is also confirmed by ESI-mass spectrometry experiments carried out for 1-Tb and 1-Tm.

Single-Crystal-to-Single-Crystal Cluster Transformation in a Microporous Molybdoarsenate(V)-Metalorganic Framework.

The hybrid compound [Cu(cyclam)(H2O)2]0.5[{Cu(cyclam)}1.5{B-H2As2Mo6O26(H2O)}]·9H2O (1) (cyclam = 1,4,8,11-tetraazacyclotetradecane) was synthesized in aqueous solution by reacting the {Cu(cyclam)}2+ complex with a mixture of heptamolybdate and an arsenate(V) source. Crystal packing of 1 exhibits a supramolecular open-framework built of discrete covalent molybdoarsenate/metalorganic units and additional [Cu(cyclam)(H2O)2]2+ cations, the stacking of which generates squarelike channels parallel to the z axis with an approximate cross section of 10 × 11 Å2 where all the hydration water molecules are hosted. Thermal evacuation of solvent molecules yields a new anhydrous crystalline phase, but compound 1 does not preserve its single-crystalline nature upon heating. However, when crystals are dehydrated under vacuum, they undergo a structural transformation that proceeds via a single-crystal-to-single-crystal pathway, leading to the anhydrous phase [{Cu(cyclam)}2(A-H2As2Mo6O26)] (2). Total dehydration results in important modifications within the inorganic cluster skeleton which reveals an unprecedented solid-state B to A isomerization of the polyoxoanion. This transition also involves changes in the CuII bonding scheme that lead to covalent cluster/metalorganic layers by retaining the open-framework nature of 1. Compound 2 adsorbs ambient moisture upon air exposure, but it does not revert back to 1, and the hydrated phase [{Cu(cyclam)}2(A-H2As2Mo6O26)]·6H2O (2h) is obtained instead. Structural variations between 1 and 2 are reflected in electron paramagnetic resonance spectroscopy measurements, and the permanent microporosity of 2 provides interesting functionalities to the system such as the selective adsorption of gaseous CO2 over N2.

Modulating Magnetic and Photoluminescence Properties in 2-Aminonicotinate-Based Bifunctional Coordination Polymers by Merging 3d Metal Ions.

Herein, the synthesis and study of bifunctional coordination polymers (CPs) with both magnetic and photoluminescence properties, derived from a heterometallic environment, are reported. As a starting point, three isostructural monometallic CPs with the formula [M(µ-2ani)2 ]n (MII =Mn (1Mn ), Co (3Co ) and Ni (4Ni ); 2ani=2-aminonicotinate), crystallise as chiral 2D-layered structures stacked by means of supramolecular interactions. These compounds show high thermal stability in the solid state (above 350 °C), despite which, in aqueous solution, compound 1Mn is shown to partially transform into a novel 1D chain CP with the formula [Mn(2ani)2 (µ-H2 O)2 ]n (2Mn ). A study of the direct current (dc) magnetic properties of 1Mn , 3Co and 4Ni reveals a spin-canted structure derived from antisymmetric antiferromagnetic weak exchanges along the chiral network (as confirmed by DFT calculations) and magnetic anisotropy of the ions, in such a way that long-range ordering is observed with variable magnitude for the spin carriers. Moreover, compounds 3Co and 4Ni show no frequency-dependent alternating current (ac) susceptibility curves under zero dc field; this is characteristic behaviour of a glassy state that may be partially supressed for 3Co by applying an external dc field. To overcome long-range magnetic ordering, CoII ions are diluted in a diamagnetic ZnII -based matrix, which enables single-molecule magnet behaviour. Interestingly, this strategy allows a bifunctional Cox Zn1-x 2ani material, which is imbued with a strong photoluminescent emitting capacity, as characterised by an intense blue light followed by a green afterglow, to be obtained.

Chromium Speciation in Zirconium-Based Metal-Organic Frameworks for Environmental Remediation.

Acute CrVI water pollution due to anthropogenic activities is an increasing worldwide concern. The high toxicity and mobility of CrVI makes it necessary to develop dual adsorbent/ion-reductive materials that are able to capture CrVI and transform it efficiently into the less hazardous CrIII . An accurate description of chromium speciation at the adsorbent/ion-reductive matrix is key to assessing whether CrVI is completely reduced to CrIII , or if its incomplete transformation has led to the stabilization of highly reactive, transient CrV species within the material. With this goal in mind, a dual ultraviolet-visible and electron paramagnetic spectroscopy approach has been applied to determine the chromium speciation within zirconium-based metal-organic frameworks (MOFs). Our findings point out that the generation of defects at Zr-MOFs boosts CrVI adsorption, whilst the presence of reductive groups on the organic linkers play a key role in stabilizing it as isolated and/or clustered CrIII ions.

Iron-Doped Sodium-Vanadium Fluorophosphates: Na3V2-yO2-yFey(PO4)2F1+y (y < 0.3).

The sodium-vanadium fluorophosphate family has been actively investigated recently, but few examples tackle chemical doping or the substitution of vanadium. This work presents a series of iron-doped compounds Na3V2-yO2-yFey(PO4)2F1+y (y ≤ 0.3) prepared by hydrothermal synthesis with low iron content. The amount of iron in the structure is confirmed by X-ray and neutron powder diffraction, electronic paramagnetic resonance, magnetic susceptibility measurements, and solid-state nuclear magnetic resonance (ssNMR). The degree of vanadium substitution, together with the solubility limit for iron in sodium-vanadium fluorophosphates, has been calculated by ssNMR and magnetic susceptibility measurements to be y = 0.3 based on the synthetic route used here. The introduction of small amounts of Fe3+ to the structure leads to the reduction of a fraction of V4+ to V3+, and the voltage profiles do not change with the introduction of iron to the structure. In situ synchrotron X-ray diffraction demonstrates that the electrochemical-structural changes during charge and discharge are very similar to those observed in the V3+/V4+ mixed-valent Na3V2O1.6(PO4)2F1.4, which could be related to the existence of both iron dopant and V3+ in the phase.

[Assessing illicit drugs in wastewater: a pilot study in Mexico]. / Medición de drogas ilícitas en aguas residuales: estudio piloto en México.

OBJECTIVE: Monitor drug use through wastewater metabolite measurement. MATERIALS AND METHODS: Wastewater samples were obtained from 31 wastewater treatment plants and 95 sites with specific populations (38 schools, 42 units of addiction treatment and 15 penitentiaries). Using ultra high liquid chromatography, we measured nine metabolites from six drugs. RESULTS: Eight out of nine drug metabolites were identified in the samples. Marijuana (THC-COOH), cocaine (benzoylecgonine) and methamphetamine were identified in schools, centers of addiction treatment and penitentiaries. Nuevo Laredo, Culiacan and Torreon had the highest consumption of cocaine, marijuana, amphetamine and methamphetamine. CONCLUSIONS: Monitoring drug use through wastewater is feasible in Mexico and could constitute a surveillance system to identify changes in the time.

OBJECTIVE: Monitorear el consumo de drogas a través de la medición de sus metabolitos en aguas residuales. MATERIALS AND METHODS: Se obtuvieron muestras de 31 plantas de tratamiento de agua residual y de 95 sitios con poblaciones específicas (38 escuelas, 42 unidades de tratamiento de adicciones y 15 centros de readaptación social). Usando cromatografía líquida de ultra-alta resolución, se midieron nueve metabolitos de seis drogas. RESULTS: Ocho de nueve metabolitos de drogas fueron identificados en aguas residuales. Los metabolitos de marihuana (THC-COOH), cocaína (benzoilecgonina) y metanfetamina fueron identificados en escuelas, centros de readaptación social y de tratamiento de adicciones. En Nuevo Laredo, Culiacán y Torreón se encontraron los consumos per cápita más elevados de cocaína, marihuana, anfetamina y metanfetamina. CONCLUSIONS: El monitoreo del uso de drogas a través de aguas residuales es factible en México y podría constituir un sistema de vigilancia para identificar cambios de su consumo en el tiempo.

Structural Transformations in the Thermal Dehydration of [Cu2(bpa)(btec)(H2O)4]n Coordination Polymer.

Reactions between pyridinic ligands such as 1,2-bis(4-pyridyl)ethane (bpa) and transition metal cations are a very widespread technique to produce extended coordination polymers such as Metal-Organic Frameworks. In combination with a second ligand these systems could present different topologies and behaviors. In this context, the use of 1,2,4,5-benzenetetracarboxylic acid (H4btec) gave us a novel 2D compound, [Cu2(bpa)(btec)(H2O)4]n (1), which was prepared by microwave-assisted synthesis and structurally characterized by means of single crystal X-ray diffraction. Its thermal behavior was analyzed through thermogravimetric analysis and variable temperature powder X-ray diffraction, concluding that thermal stability is influenced by the coordination water molecules, allowing two sequential thermochromic phase transformations to take place. These transformations were monitored by electronic paramagnetic resonance spectroscopy and magnetic susceptibility measurements. In addition, the crystal structure of the anhydrous compound [Cu2(bpa)(btec)]n (1.ah) was determined. Finally, a topological study was carried out for the bpa ligand considering all the structures deposited in the Cambridge Structural Databased. More than 1000 structures were analyzed and classified into 17 different topologies, according to the role of the ligand.

Site symmetry and host sensitization-dependence of Eu3+ real time luminescence in tin dioxide nanoparticles.

The present work gives a detailed investigation of the dependence of the real time luminescence of Eu3+-doped tin dioxide nanopowder on rare earth (RE) site symmetry and host defects. Ultrafast time-resolved analysis of both RE-doped and undoped nanocrystal powder emissions, together with electronic paramagnetic resonance studies, show that host-excited RE emission is associated with RE-induced oxygen vacancies produced by the non-isoelectronic RE-tin site substitution that are decoupled from those producing the bandgap excited emission of the SnO2 matrix. A lower limit for the host-RE energy transfer rate and a model for the excitation mechanism are given.

Experimental and DFT characterization, antioxidant and anticancer activities of a Cu(II)-irbesartan complex: structure-antihypertensive activity relationships in Cu(II)-sartan complexes.

The coordination compound of the antihypertensive ligand irbesartan (irb) with copper(II) (CuIrb) was synthesized and characterized by FTIR, FT-Raman, UV-visible, reflectance and EPR spectroscopies. Experimental evidence allowed the implementation of structural and vibrational studies by theoretical calculations made in the light of the density functional theory (DFT). This compound was designed to induce structural modifications on the ligand. No antioxidant effects were displayed by both compounds, though CuIrb behaved as a weak 1,1-diphenyl-2-picrylhydrazyl radical (DPPH(·)) scavenger (IC50 = 425 µM). The measurements of the contractile capacity on human mesangial cell lines showed that CuIrb improved the antihypertensive effects of the parent medication. In vitro cell growth inhibition against prostate cancer cell lines (LNCaP and DU 145) was measured for CuIrb, irbesartan and copper(II). These cell lines have been selected since the angiotensin II type 1 (AT1) receptor (that was blocked by the angiotensin receptor blockers, ARB) has been identified in them. The complex exerted anticancer behavior (at 100 µM) improving the activity of the ligand. Flow cytometry determinations were used to determine late apoptotic mechanisms of cell death. Experimental and DFT characterization of an irbesartan copper(II) complex has been performed. The complex exhibits low scavenging activity against DPPH(·) and significant growth inhibition of LNCaP and DU 145 prostate cancer cell lines. Flow cytometry determinations were used to determine late apoptotic mechanisms of cell death. This compound improved the antihypertensive effect of irbesartan. This effect was observed earlier for the mononuclear Cu-candesartan complex, but not in structurally modified sartans forming dinuclear or octanuclear Cu-sartan compounds.

New Perspectives for Old Clusters: Anderson-Evans Anions as Building Blocks of Large Polyoxometalate Frameworks in a Series of Heterometallic 3 d-4 f Species.

A series of nine [Sb7W36O133Ln3M2(OAc)(H2O)8](17-) heterometallic anions (Ln3M2; Ln=La-Gd, M=Co; Ln=Ce, M=Ni and Zn) have been obtained by reacting 3 d metal disubstituted Krebs-type tungstoantimonates(III) with early lanthanides. Their unique tetrameric structure contains a novel {MW9O33} capping unit formed by a planar {MW6O24} fragment to which three {WO2} groups are condensed to form a tungstate skeleton identical to that of a hypothetical trilacunary derivative of the ɛ-Keggin cluster. It is shown, for the first time, that classical Anderson-Evans {MW6O24} anions can act as building blocks to construct purely inorganic large frameworks. Unprecedented reactivity in the outer ring of these disk-shaped species is also revealed. The Ln3M2 anions possess chirality owing to a {Sb4O4} cluster being encapsulated in left- or right-handed orientations. Their ability to self-associate in blackberry-type vesicles in solution has been assessed for the Ce3Co2 derivative.

Commensurate Superstructure of the {Cu(NO3)(H2O)}(HTae)(Bpy) Coordination Polymer: An Example of 2D Hydrogen-Bonding Networks as Magnetic Exchange Pathway.

The average and commensurate superstructures of the one-dimensional coordination polymer {Cu(NO3)(H2O)}(HTae)(Bpy) (H2Tae = 1,1,2,2-tetraacetylethane, Bpy = 4,4'-bipyridine) were determined by single-crystal X-ray diffraction, and the possible symmetry relations between the space group of the average structure and the superstructure were checked. The crystal structure consists in parallel and oblique {Cu(HTae)(Bpy)} zigzag metal-organic chains stacked along the [100] crystallographic direction. The origin of the fivefold c axis in the commensurate superstructure is ascribed to a commensurate modulation of the coordination environment of the copper atoms. The commensurately ordered nitrate groups and coordinated water molecules establish a two-dimensional hydrogen-bonding network. Moreover, the crystal structure shows a commensurate to incommensurate transition at room temperature. The release of the coordination water molecules destabilizes the crystal framework, and the compound shows an irreversible structure transformation above 100 °C. Despite the loss of crystallinity, the spectroscopic studies indicate that the main building blocks of the crystal framework are retained after the transformation. The hydrogen-bonding network not only plays a crucial role stabilizing the crystal structure but also is an important pathway for magnetic exchange transmission. In fact, the magnetic susceptibility curves indicate that after the loss of coordinated water molecules, and hence the collapse of the hydrogen-bonding network, the weak anti-ferromagnetic coupling observed in the initial compound is broken. The electron paramagnetic resonance spectra are the consequence of the average signals from Cu(II) with different orientations, indicating that the magnetic coupling is effective between them. In fact, X- and Q-band data are reflecting different situations; the X-band spectra show the characteristics of an exchange g-tensor, while the Q-band signals are coming from both the exchange and the molecular g-tensors.

Antioxidant, anticancer activities and mechanistic studies of the flavone glycoside diosmin and its oxidovanadium(IV) complex. Interactions with bovine serum albumin.

The natural antioxidant flavonoid diosmin, found in citric fruits, showed low antioxidant properties among other flavonoids due to its structural characteristics and low cytotoxicity against lung (A549) and breast (T47D, SKBR3 and MDAMB231) cancer cell lines. The anticancer behavior has been improved by the metal complex generated with the flavonoid and the oxidovanadium(IV) ion. This new complex, [VO(dios)(OH)3]Na5·6H2O (VOdios), has been synthesized and characterized both in solid and solution states. The interaction of the metal ion through the sugar moiety of diosmin precluded the improvement of the antioxidant effects. However, the cell-killing effects tested in human lung A549 and breast T47D, SKBR3 and MDAMB231 cancer cell lines, were enhanced by complexation. The anti-proliferative effects on the human lung cancer cell line were accompanied by cellular ROS generation and an increase in cytoplasm condensation. The breast cancer cell lines did not produce caspase3/7 activation, mitochondrial potential reduction and ROS generation. Therefore, a non-apoptotic form of cell death in a caspase- and oxidative stress-independent manner has been proposed. The protein binding ability has been monitored by the quenching of tryptophan emission in the presence of the compounds using bovine serum albumin (BSA) as a model protein. Both compounds could be distributed and transported in vivo and the complex displayed stronger binding affinity and higher contributions to the hydrogen bond and van der Waals forces.

Rearrangement of a Krebs-type polyoxometalate upon coordination of N,O-bis(bidentate) ligands.

Selective coordination of 2,3-pyzdc to the Krebs-type [{Ni(H2O)3}2(WO2)2(SbW9O33)2](10-) anion promotes a skeletal rearrangement that results in the [(2,3-pyzdc)2{NaNi2(H2O)4Sb2W20O70}2](22-) (Ni4) hybrid dimer showing a novel dinickel containing a 20-tungsto-2-antimonate(III) framework stabilized by N,O-bis(bidentate) bridging ligands. The solution stability and magnetism of Ni4 is discussed.

High-voltage cathode materials for lithium-ion batteries: freeze-dried LiMn0.8Fe0.1M0.1PO4/C (M = Fe, Co, Ni, Cu) nanocomposites.

Four LiMn0.8Fe0.1M0.1PO4/C (M = Fe, Co, Ni, Cu) cathode materials have been synthesized via a freeze-drying method. The samples have been characterized by powder X-ray diffraction, transmission electron microscopy, magnetic susceptibility, and electrochemical measurements. The composition and effective insertion of the transition-metal substituents in LiMnPO4 have been corroborated by elemental analysis, the evolution of the crystallographic parameters, and the magnetic properties. The morphological characterization of the composites has demonstrated that the phosphate nanoparticles are enclosed in a matrix of amorphous carbon. Among them, LiMn0.8Fe0.1Ni0.1PO4/C is the most promising cathode material, providing a good electrochemical performance in all aspects: high voltage and specific capacity values, excellent cyclability, and good rate capability. This result has been attributed to several factors, such as the suitable morphology of the sample, the good connection afforded by the in situ generated carbon, and the amelioration of the structural stress provided by the presence of Ni(2+) and Fe(2+) in the olivine structure.

Cation-directed dimeric versus tetrameric assemblies of lanthanide-stabilized dilacunary Keggin tungstogermanates.

Reaction of mid- to late lanthanide ions with GeO2 and Na2WO4 in NaOAc buffer results in a library of [Ln2 (GeW10O38)](6-) clusters (Ln2), which consist of dilacunary Keggin fragments stabilized by the insertion of 4f atoms in the vacant sites and show the ability to undergo cation-directed self-assembly processes. In the presence of Na(+), two ß-Ln2 subunits assemble by means of Ln-O(WO5)-Ln bridges to form the chiral [Ln4(H2O)6(ß-GeW10O38)2](12-) dimeric anions (ßß-Ln4, Ln = Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu). When Cs(+) is present, two Ln4-like dimers further assemble into the [{Ln4(H2O)5(GeW10O38)2}2](24-) species (Ln8, Ln = Ho, Er, Tm, Yb, Lu). Two types of tetramers coexist in the solid state: One shows a full ßß-Ln8 architecture, whereas the other one is a mixed αß-Ln8 assembly in which each ß-subunit is linked to its corresponding α-Ln2 derivative. Regardless of differences in isomeric forms and the relative arrangement of Ln2 subunits, all anions display virtually identical {Ln4} cores as a common structural feature. A combination of ESI mass spectrometry and (183)W NMR spectroscopy experiments indicates that Ln8 tetramers fragment into Ln4 dimers upon dissolution, which undergo partial dissociation into Ln2 monomers and slow dimer/monomer equilibration. This is most likely followed by ß-to-α isomerization of Ln2 clusters with consequent reassembly, as indicated by isolation of three additional αα-Ln4 derivatives. Magnetic and photoluminescence properties in the Na-ßß-Ln4 series are also discussed.