Femtosecond written fiber Bragg gratings in ytterbium-doped fibers for fiber lasers in the kilowatt regime.

We investigate the high-power durability of fiber Bragg gratings written directly into an ytterbium-doped large mode area fiber using ultrashort laser pulses. The gratings were successfully integrated as a high reflector into an oscillator setup reaching up to 1.9 kW signal output power with an efficiency of 87%. Defect states induced during the inscription process could be drastically reduced by a self-annealing process resulting in a stable laser performance.

Experimental investigations on the TMI thresholds of low-NA Yb-doped single-mode fibers.

In this contribution we investigate the transversal mode instability behavior of a ytterbium-doped commercial 20/400 fiber and obtain 2.9 kW of output power after optimizing the influencing parameters. In this context, we evaluate the influence of the bend diameter and the pump wavelength within the scope of the absorption length and the length of the fiber. Furthermore, with a newly developed fiber we report on 4.4 kW of single-mode output power at 40 cm bend diameter.

Measuring thermal load in fiber amplifiers in the presence of transversal mode instabilities.

We report on detailed in situ distributed temperature measurements inside a high power fiber amplifier. The deducted thermal load and the transversal mode instability (TMI) threshold of a commercial large mode area fiber with 25 µm core and 400 µm cladding were measured at various seed wavelengths. By matching these results with detailed simulations we show that photodarkening has a negligible impact on the thermal load and, therefore, on the TMI threshold in this fiber.

Scalability of components for kW-level average power few-cycle lasers.

In this paper, the average power scalability of components that can be used for intense few-cycle lasers based on nonlinear compression of modern femtosecond solid-state lasers is investigated. The key components of such a setup, namely, the gas-filled waveguides, laser windows, chirped mirrors for pulse compression and low dispersion mirrors for beam collimation, focusing, and beam steering are tested under high-average-power operation using a kilowatt cw laser. We demonstrate the long-term stable transmission of kW-level average power through a hollow capillary and a Kagome-type photonic crystal fiber. In addition, we show that sapphire substrates significantly improve the average power capability of metal-coated mirrors. Ultimately, ultrabroadband dielectric mirrors show negligible heating up to 1 kW of average power. In summary, a technology for scaling of few-cycle lasers up to 1 kW of average power and beyond is presented.

Optimizing mode instability in low-NA fibers by passive strategies.

Systematic experimental investigations toward the mode instability (MI) threshold in low-NA fibers are performed. By testing several fibers with varying V-parameters drawn from the same preform, a high degree of reproducibility of the experimental conditions could be achieved. This allows for systematic investigations on isolated parameters influencing the complex behavior of MI. A maximum MI threshold of 2 kW could be demonstrated for the tested fibers, which represents a new record output power for narrow linewidth fiber amplifiers. The MI threshold was found to sensitively depend on the V-parameter for large V-parameters (>2), but to be robust for smaller V-parameters. Furthermore, the fiber bending diameter and the seed excitation conditions were identified to sensitively influence the MI threshold.

Thermally induced waveguide changes in active fibers.

Thermally induced waveguide changes become significant for very large mode area fibers. This results in a reduction of the mode-field diameter, but simultaneously in an improvement of the beam quality. In this work the first systematic experimental characterization of the reduction of the mode-field diameter in various fibers during high-power operation is carried out. It is shown that the reduction of the mode-field diameter shows a characteristic behavior that scales with the core size but that is independent of the particular fiber design. Furthermore, the strength of the actual index change is experimentally estimated, and its use to overcome avoided crossings is discussed and experimentally demonstrated.

Build up and decay of mode instability in a high power fiber amplifier.

State-of-the-art high power Yb-doped large mode area fibers have been developed to a performance level able to reach the so-called mode instability threshold. In this contribution we will discuss the experimental results regarding the temporal evolution (build up and decay) of this effect to come closer to a comprehensive understanding of its driving mechanisms. Our investigations prove that the relevant time scale for build up and decay of mode instability is in the millisecond range and thus deliver experimental evidence of underlying thermal effects. To the best of our knowledge these are the first systematic, time resolved investigations on that topic.

26 mJ, 130 W Q-switched fiber-laser system with near-diffraction-limited beam quality.

We demonstrate a Q-switched fiber laser system emitting sub-60 ns pulses with 26 mJ pulse energy and near-diffraction-limited beam quality (M2<1.3). In combination with a repetition rate of 5 kHz, a corresponding average output power of 130 W is achieved. This record performance is enabled by a large-pitch fiber with a core diameter of 135 µm. This fiber allows for effective single-mode operation with mode field diameters larger than 90 µm even at average output powers exceeding 100 W.

Q-switching of Yb3+-doped fiber laser using a novel micro-optical waveguide on microactuating platform light modulator.

We report a novel micro-optical waveguide (MOW) on microactuating platform (MAP) light modulator for Q-switched all-fiber laser applications. The light modulator employs a fused biconical taper (FBT) coupler, which acts as MOW, mounted on an electromechanical system, MAP, where an axial stress over the waist of FBT coupler is precisely controlled to result in modulation of output power. The modulator was implemented in a clad pumped Yb3+-doped fiber laser cavity as a Qswitching element. Q-switching was successfully achieved at the repetition rate of 18.6kHz and average pulse energy of 1.4microJ. The proposed structure can be readily applied in power scaling up of all-fiber Q-switching laser systems.