Aligned Conjugated Polymer Nanofiber Networks in an Elastomer Matrix for High-Performance Printed Stretchable Electronics.

Conjugated polymer films are promising in wearable X-ray detection. However, achieving optimal film microstructure possessing good electrical and detection performance under large deformation via scalable printing remains challenging. Herein, we report bar-coated high-performance stretchable films based on a conjugated polymer P(TDPP-Se) and elastomer SEBS blend by optimizing the solution-processing conditions. The moderate preaggregation in solution and prolonged growth dynamics from a solvent mixture with limited dissolving capacity is critical to forming aligned P(TDPP-Se) chains/crystalline nanofibers in the SEBS phase with enhanced π-π stacking for charge transport and stress dissipation. The film shows a large elongation at break of >400% and high mobilities of 5.29 cm2 V-1 s-1 at 0% strain and 1.66 cm2 V-1 s-1 over 500 stretch-release cycles at 50% strain, enabling good X-ray imaging with a high sensitivity of 1501.52 µC Gyair-1 cm-2. Our work provides a morphology control strategy toward high-performance conjugated polymer film-based stretchable electronics.

Interlamellar-Spacing Engineering of Stable and Toxicity-Reduced 2D Perovskite Single Crystal for High-Resolution X-ray Imaging.

Two-dimensional (2D) lead halide perovskites are excellent candidates for X-ray detection due to their high resistivity, high ion migration barrier, and large X-ray absorption coefficients. However, the high toxicity and long interlamellar distance of the 2D perovskites limit their wide application in high sensitivity X-ray detection. Herein, we demonstrate stable and toxicity-reduced 2D perovskite single crystals (SCs) realized by interlamellar-spacing engineering via a distortion self-balancing strategy. The engineered low-toxicity 2D SC detectors achieve high stability, large mobility-lifetime product, and therefore high-performance X-ray detection. Specifically, the detectors exhibit a record high sensitivity of 13488 µC Gy1- cm-2, a low detection limit of 8.23 nGy s-1, as well as a high spatial resolution of 8.56 lp mm-1 in X-ray imaging, all of which are far better than those of the high-toxicity 2D lead-based perovskite detectors. These advances provide a new technical solution for the low-cost fabrication of low-toxicity, scalable X-ray detectors.

Defect Passivation and Crystallization Regulation for Efficient and Stable Formamidinium Lead Iodide Solar Cells with Multifunctional Amidino Additive.

Amidino-based additives show great potential in high-performance perovskite solar cells (PSCs). However, the role of different functional groups in amidino-based additives have not been well elucidated. Herein, two multifunctional amidino additives 4-amidinobenzoic acid hydrochloride (ABAc) and 4-amidinobenzamide hydrochloride (ABAm) are employed to improve the film quality of formamidinium lead iodide (FAPbI3) perovskites. Compared with ABAc, the amide group imparts ABAm with larger dipole moment and thus stronger interactions with the perovskite components, i.e., the hydrogen bonds between N…H and I- anion and coordination bonds between C = O and Pb2+ cation. It strengthens the passivation effect of iodine vacancy defect and slows down the crystallization process of α-FAPbI3, resulting in the significantly reduced non-radiative recombination, long carrier lifetime of 1.7 µs, uniformly large crystalline grains, and enhances hydrophobicity. Profiting from the improved film quality, the ABAm-treated PSC achieves a high efficiency of 24.60%, and maintains 93% of the initial efficiency after storage in ambient environment for 1200 hours. This work provides new insights for rational design of multifunctional additives regarding of defect passivation and crystallization control toward highly efficient and stable PSCs.

Enhancing Performance and Stability of Perovskite Solar Cells with a Novel Formamidine Group Additive.

Perovskite materials, particularly FAPbI3, have emerged as promising candidates for solar energy conversion applications. However, these materials are plagued by well-known defects and suboptimal film quality. Enhancing crystallinity and minimizing defect density are therefore essential steps in the development of high-performance perovskite solar cells. In this study, 1H-Pyrazole-1-carboximidamide hydrochloride (PCH) is introduced into FAPbI3 perovskite films. The molecular structure of PCH features a pyrazole ring bonded to formamidine (FA). The FA moiety of PCH facilitated the incorporation of this additive into the film lattice, while the negatively charged pyrazole ring effectively passivated positively charged iodine vacancies. The presence of PCH led to the fabrication of an FAPbI3 device with improved crystallinity, a smoother surface, and reduced defect density, resulting in enhanced Voc and fill factor. A record power conversion efficiency of 24.62% is achieved, along with exceptional stability under prolonged air exposure and thermal stress. The findings highlight the efficacy of PCH as a novel additive for the development of high-performance perovskite solar cells.

A New Metal-Free Molecular Perovskite-Related Single Crystal with Quantum Wire Structure for High-Performance X-Ray Detection.

The family of metal-free molecular perovskites, an emerging novel class of eco-friendly semiconductor, welcomes a new member with a unique 1D hexagonal perovskite structure. Lowering dimensionality at molecular level is a facile strategy for crystal structure conversion, optoelectronic property regulation, and device performance optimization. Herein, the study reports the design, synthesis, packing structure, and photophysical properties of the 1D metal-free molecular perovskite-related single crystal, rac-3APD-NH4I3(rac-3APD= racemic-3-Aminopiperidinium), that features a quantum wire structure formed by infinite chains of face-sharing NH4I6 octahedra, enabling strong quantum confinement with strongly self-trapped excited (STE) states to give efficient warm orange emission with a photoluminescence quantum yield (PLQY) as high as ≈41.6%. The study accordingly unveils its photoexcited carrier dynamics: rac-3APD-NH4I3 relaxes to STE state with a short lifetime of 10 ps but decays to ground state by emitting photons with a relatively longer lifetime of 560 ps. Additionally, strong quantum confinement effect is conducive to charge transport along the octahedral channels that enables the co-planar single-crystal X-ray detectors to achieve a sensitivity as high as 1556 µC Gyair -1 cm-2. This work demonstrates the first case of photoluminescence mechanism and photophysical dynamics of 1D metal-free perovskite-related semiconductor, as well as the promise for high-performance X-ray detector.

Passivating Grain Boundaries via Graphene Additive for Efficient Kesterite Solar Cells.

Grain boundaries (GBs)-triggered severe non-radiative recombination is recently recognized as the main culprits for carrier loss in polycrystalline kesterite photovoltaic devices. Accordingly, further optimization of kesterite-based thin film solar cells critically depends on passivating the grain interfaces of polycrystalline Cu2 ZnSn(S,Se)4 (CZTSSe) thin films. Herein, 2D material of graphene is first chosen as a passivator to improve the detrimental GBs. By adding graphene dispersion to the CZTSSe precursor solution, single-layer graphene is successfully introduced into the GBs of CZTSSe absorber. Due to the high carrier mobility and electrical conductivity of graphene, GBs in the CZTSSe films are transforming into electrically benign and do not act as high recombination sites for carrier. Consequently, benefitting from the significant passivation effect of GBs, the use of 0.05 wt% graphene additives increases the efficiency of CZTSSe solar cells from 10.40% to 12.90%, one of the highest for this type of cells. These results demonstrate a new route to further increase kesterite-based solar cell efficiency by additive engineering.

Implementation of a Multi-Functional-Group Strategy for Enhanced Performance of Perovskite Solar Cells through the Incorporation of 3-Amino-4-Phenylbutyric Acid Hydrochloride.

Reducing the defect density of perovskite films during the crystallization process is critical in preparing high-performance perovskite solar cells (PSCs). Here, a multi-functional molecule, 3-phenyl-4-aminobutyric acid hydrochloride (APH), with three functional groups including a benzene ring, ─NH3 + and ─COOH, is added into the perovskite precursor solution to improve perovskite crystallization and device performance. The benzene ring increases the hydrophobicity of perovskites, while ─NH3 + and ─COOH passivate defects related to I- and Pb2+, respectively. Consequently, the power conversion efficiency (PCE) of the optimal device increased to 24.65%. Additionally, an effective area of 1 cm2 with a PCE of 22.45% is also prepared using APH as an additive. Furthermore, PSCs prepared with APH exhibit excellent stability by 87% initial PCE without encapsulation after exposure at room temperature under 25% humidity for 5000 h and retaining 70% of initial PCE after aging at 85 °C in an N2 environment for 864 h.

Flexible Aqueous Supercapacitors for Long Cycle-Life Using Electrode with Multiple Active C═S Sites.

Even though a few organic materials have attracted considerable attention for energy storage applications, their dissolution in the electrolyte during the charging-discharging processes presents a formidable challenge to their long-term performance. In this work, according to the principle of like dissolves like, non-polar trithiocyanuric acid (TCA) can effectively inhibit dissolution in an aqueous electrolyte, hence prolonging the cycle life. Moreover, theoretical calculations suggest that TCA lowers lowest unoccupied molecular orbital (LUMO) energy level, thereby promoting reaction kinetics. The CV curves of TCA maintain a rectangular structure even at a high scan rate of 1000 mV s‒1 and exhibit a remarkable capacitance retention rate of 93.1% after 50,000 cycles. Asymmetric flexible supercapacitors utilizing the TCA exhibit an impressive energy density. Moreover, they maintain 94.2% of their capacitance after undergoing 80,000 cycles. Their integration with perovskite solar cells to facilitate the rapid storage of photogenerated charges enables efficient solar energy utilization, providing a practical solution for capturing and storing renewable energy.

Highly Stretchable Conjugated Polymer/Elastomer Blend Films with Sandwich Structure.

The physical blending of high-mobility conjugated polymers with ductile elastomers provides a simple way to realize high-performance stretchable films. However, how to control the morphology of the conjugated polymer and elastomer blend film and its response to mechanical fracture processes during stretching are not well understood. Herein, a sandwich structure is constructed in the blend film based on a conjugated polymer poly[(5-fluoro-2,1,3-benzothiadiazole-4,7-diyl)(4,4-dihexadecyl-4H-cyclopenta[2,1-b:3,4-b″]dithiophene-2,6-diyl)(6-fluoro-2,1,3-benzothiadiazole-4,7-diyl)(4,4-dihexadecyl-4H-cyclopenta[2,1-b:3,4-b″]dithiophene-2,6-diyl)] (PCDTFBT) and an elastomer polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS). The sandwich structure is composed of a PCDTFBT:SEBS mixed layer laminated with a PCDTFBT-rich layer at both the top and bottom surfaces. During stretching, the external strain energy can be effectively dissipated by the deformation of the crystalline PCDTFBT domains and amorphous SEBS phases and the recrystallization of the PCDTFBT chains. This endows the blend film with excellent ductility, with a large crack onset strain exceeding 1100%, and minimized the electrical degradation of the blend film at a large strain. This study indicates that the electrical and mechanical performance of conjugated polymer/elastomer blend films can be improved by manipulating their microstructure.

Anti-Solvent-Free Preparation for Efficient and Photostable Pure-Iodide Wide-Bandgap Perovskite Solar Cells.

The perovskite/silicon tandem solar cell (TSC) has attracted tremendous attention due to its potential to breakthrough the theoretical efficiency set for single-junction solar cells. However, the perovskite solar cell (PSC) designed as its top component cell suffers from severe photo-induced halide segregation owing to its mixed-halide strategy for achieving desirable wide-bandgap (1.68 eV). Developing pure-iodide wide-bandgap perovskites is a promising route to fabricate photostable perovskite/silicon TSCs. Here, we report efficient and photostable pure-iodide wide-bandgap PSCs made from an anti-solvent-free (ASF) technique. The ASF process is achieved by mixing two precursor solutions, both of which are capable of depositing corresponding perovskite films without involving anti-solvent. The mixed solution finally forms Cs0.3DMA0.2MA0.5PbI3 perovskite film with a bandgap of 1.68 eV. Furthermore, methylammonium chloride additive is applied to enhance the crystallinity and reduce the trap density of perovskite films. As a result, the pure-iodide wide-bandgap PSC delivers efficiency as high as 21.30 % with excellent photostability, the highest for this type of solar cells. The ASF method significantly improves the device reproducibility as compared with devices made from other anti-solvent methods. Our findings provide a novel recipe to prepare efficient and photostable wide-bandgap PSCs.

Lattice Mismatch at the Heterojunction of Perovskite Solar Cells.

Lattice mismatch significantly influences microscopic transport in semiconducting devices, affecting interfacial charge behavior and device efficacy. This atomic-level disordering, often overlooked in previous research, is crucial for device efficiency and lifetime. Recent studies have highlighted emerging challenges related to lattice mismatch in perovskite solar cells, especially at heterojunctions, revealing issues like severe tensile stress, increased ion migration, and reduced carrier mobility. This review systematically discusses the effects of lattice mismatch on strain, material stability, and carrier dynamics. It also includes detailed characterizations of these phenomena and summarizes current strategies including epitaxial growth and buffer layer, as well as explores future solutions to mitigate mismatch-induced issues. We also provide the challenges and prospects for lattice mismatch, aiming to enhance the efficiency and stability of perovskite solar cells, and contribute to renewable energy technology advancements.

Multi-Group Polymer Coating on Zn Anode for High Overall Conversion Efficiency Photorechargeable Zinc-Ion Batteries.

The solar-driven photorechargeable zinc-ion batteries have emerged as a promising power solution for smart electronic devices and equipment. However, the subpar cyclic stability of the Zn anode remains a significant impediment to their practical application. Herein, poly(diethynylbenzene-1,3,5-triimine-2,4,6-trione) (PDPTT) was designed as a functional polymer coating of Zn. Theoretical calculations demonstrate that the PDPTT coating not only significantly homogenizes the electric field distribution on the Zn surface, but also promotes ion-accessible surface of Zn. With multiple N and C=O groups exhibiting strong adsorption energies, this polymer coating reduces the nucleation overpotential of Zn, alters the diffusion pathway of Zn2+ at the anode interface, and decreases the corrosion current and hydrogen evolution current. Leveraging these advantages, Zn-PDPTT//Zn-PDPTT exhibits an exceptionally long cycling time (≥4300 h, 1 mA cm-2). Zn-PDPTT//AC zinc-ion hybrid capacitors can withstand 50,000 cycles at 5 A/g. Zn-PDPTT//NVO zinc-ion battery exhibits a faster charge storage rate, higher capacity, and excellent cycling stability. Coupling Zn-PDPTT//NVO with high-performance perovskite solar cells results in a 13.12% overall conversion efficiency for the photorechargeable zinc-ion battery, showcasing significant value in advancing the efficiency and upgrading conversion of renewable energy utilization.

Designed Additive to Regulated Crystallization for High Performance Perovskite Solar Cell.

It is a crucial role for enhancing the power conversion efficiency (PCE) of perovskite solar cells (PSCs) to prepare high-quality perovskite films, which can be achieved by delaying the crystallization of perovskite film. Hence, we designed difluoroacetic anhydride (DFA) as an additive to regulating crystallization process thus reducing defect formation during perovskite film formation. It was found DFA reacts with DMSO by forming two molecules, difluoroacetate thioether ester (DTE) and difluoroacetic acid (DA). The strong bonding DTE⋅PbI2 and DA⋅PbI2 retard perovskite crystallization process for high-quality film formation, which was monitored through in situ UV/Vis and PL tests. By using DFA additives, we prepared perovskite films with high-quality and low defects. Finally, a champion PCE of 25.28 % was achieved with excellent environmental stability, which retained 95.75 % of the initial PCE after 1152 h at 25 °C under 25 % RH.

Glycol Monomethyl Ether-Substituted Carbazolyl Hole-Transporting Material for Stable Inverted Perovskite Solar Cells with Efficiency of 25.52.

Organic self-assembled molecules (OSAMs) based hole transporting materials play a pivotal role in achieving highly efficient and stable inverted perovskite solar cells (IPSCs). However, the reported carbazol-based OSAMs have serious drawbacks, such as poor solubility in alcohol solution, worse matched energy arrangement with perovskite, and limited molecular species, which greatly limit the device performance. To address above problems, a novel OSAM 4-(3,6-glycol monomethyl ether-9H-carbazol-9-yl) butyl]phosphonic acid (GM-4PACz) was synthesized as hole-transporting material by introducing glycol monomethyl ether (GM) side chains at carbazolyl unit. GM groups enhance the surface energy of Indium Tin Oxide (ITO)/SAM substrate to facilitate the nucleation and growth of up perovskite film, suppress cation defects, release the residual stress at SAM/perovskite interface, and evaluate energy level for matching with perovskite. Consequently, the GM-4PACz based IPSC achieves a champion PCE of 25.52%, a respectable open-circuit voltage (VOC) of 1.21 V, a high stability, possessing 93.29% and 91.75% of their initial efficiency after aging in air for 2000 h or tracking at maximum power point for 1000 h, respectively.

Hydrophobic Hydrogen-Bonded Polymer Network for Efficient and Stable Perovskite/Si Tandem Solar Cells.

The pursuit of highly efficient and stable wide-band gap (WBG) perovskite solar cells (PSCs), especially for monolithic perovskite/silicon tandem devices, is a key focus in achieving the commercialization of perovskite photovoltaics. In this study, we initially designed poly(ionic liquid)s (PILs) with varying alkyl chain lengths based on density functional theory calculations. Results pinpoint that PILs with longer alkyl chain lengths tend to exhibit more robust binding energy with the perovskite structure. Then we synthesized the PILs to craft a hydrophobic hydrogen-bonded polymer network (HHPN) that passivates the WBG perovskite/electron transport layer interface, inhibits ion migration and serves as a barrier layer against water and oxygen ingression. Accordingly, the HHPN effectively curbs nonradiative recombination losses while facilitating efficient carrier transport, resulting in substantially enhanced open-circuit voltage (Voc ) and fill factor. As a result, the optimized single-junction WBG PSC achieves an impressive efficiency of 23.18 %, with Voc as high as 1.25 V, which is the highest reported for WBG (over 1.67 eV) PSCs. These devices also demonstrate outstanding thermostability and humidity resistance. Notably, this versatile strategy can be extended to textured perovskite/silicon tandem cells, reaching a remarkable efficiency of 28.24 % while maintaining exceptional operational stability.

Kinetics Controlled Perovskite Crystallization for High Performance Solar Cells.

The power conversion efficiencies (PCEs) of perovskite solar cells have recently developed rapidly compared to crystalline silicon solar cells. To have an effective way to control the crystallization of perovskite thin films is the key for achieving good device performance. However, a paradox in perovskite crystallization is from the mismatch between nucleation and Oswald ripening. Usually, the large numbers of nucleation sites tend to weak Oswald ripening. Here, we proposed a new mechanism to promote the formation of nucleation sites by reducing surface energy from 44.9 mN/m to 36.1 mN/m, to spontaneously accelerate the later Oswald ripening process by improving the grain solubility through the elastic modulus regulation. The ripening rate is increased from 2.37 Åm ⋅ s-1 to 4.61 Åm ⋅ s-1 during annealing. Finally, the solar cells derived from the optimized films showed significantly improved PCE from 23.14 % to 25.32 %. The long-term stability tests show excellent thermal stability (the optimized device without encapsulation maintaining 82 % of its initial PCE after 800 h aging at 85 °C) and an improved light stability under illumination. This work provides a new method, the elastic modulus regulation, to enhance the ripening process.

Unveiling the Origin of Co3 O4 Quantum Dots for Photocatalytic Overall Water Splitting.

Spinel cobalt oxide displays excellent photocatalytic performance, especially in solar driven water oxidation. However, the process of water reduction to hydrogen is considered as the Achilles' heel of solar water splitting over Co3 O4 owing to its low conduction band. Enhancement of the water splitting efficiency using Co3 O4 requires deeper insights of the carrier dynamics during water splitting process. Herein, the carrier dynamic kinetics of colloidal Co3 O4 quantum dots-Pt hetero-junctions is studied, which mimics the hydrogen reduction process during water splitting. It is showed that the quantum confinement effect induced by the small QD size raised the conduction band edge position of Co3 O4 QDs, so that the ligand-to-metal charge transfer from 2p state of oxygen to 3d state of Co2+ occurs, which is necessary for overall water splitting and cannot be achieved in Co3 O4 bulk crystals. The findings in this work provide insights of the photocatalytic mechanism of Co3 O4 catalysts and benefit rational design of Co3 O4 -based photocatalytic systems.

Stable and High-Efficiency Perovskite Solar Cells Using Effective Additive Ytterbium Fluoride.

With better light utilization, larger tolerance factor, and higher power conversion efficiency (PCE), the HC(NH2 )2 + (FA)-based perovskite is proven superior to the popular CH3 NH3 + (MA)- and Cs-based halide perovskites in solar cell applications. Unfortunately, limited by intrinsic defects within the FA-based perovskite films, the perovskite films can be easily transformed into a yellow δ-phase at room temperature in the fabrication process, a troublesome challenge for its further development. Here, ytterbium fluoride (YbF3 ) is introduced into the perovskite precursor for three objectives. First of all, the partial substitution of Yb3+ for Pb2+ in the perovskite lattice increases the tolerance factor of the perovskite lattice and facilitates the formation of the α phase. Second, YbF3 and DMSO in the solvent form a Lewis acid complex YbF3 ·DMSO, which can passivate the perovskite film, reduce defects, and improve device stability. Consequently, the YbF3 modified Perovskite solar cell exhibits a champion conversion efficiency of 24.53% and still maintains 90% of its initial efficiency after 60 days of air exposure under 30% relative humidity.

Low-Cost Antimony Selenosulfide with Tunable Bandgap for Highly Efficient Solar Cells.

About 10% efficient antimony selenosulfide (Sb2 (S,Se)3 ) solar cell is realized by using selenourea as a hydrothermal raw material to prepare absorber layers. However, tailoring the bandgap of hydrothermal-based Sb2 (S,Se)3 film to the ideal bandgap (1.3-1.4 eV) using the selenourea for optimal efficiency is still a challenge. Moreover, the expensive selenourea dramatically increases the fabricating cost. Here, a straightforward one-step hydrothermal method is developed to prepare high-quality Sb2 (S,Se)3 films using a novel precursor sodium selenosulfate as the selenium source. By tuning the Se/(Se+S) ratio in the hydrothermal precursor solution, a series of high-quality Sb2 (S,Se)3 films with reduced density of deep defect states and tunable bandgap from 1.31 to 1.71 eV is successfully prepared. Consequently, the best efficiency of 10.05% with a high current density of 26.01 mA cm-2 is achieved in 1.35 eV Sb2 (S,Se)3 solar cells. Compared with the traditional method using selenourea, the production cost for the Sb2 (S,Se)3  devices is reduced by over 80%. In addition, the device exhibits outstanding stability, maintaining more than 93% of the initial power conversion efficiency after 30 days of exposure in the atmosphere without encapsulation. The present work definitely paves a facile and effective way to develop low-cost and high-efficiency chalcogenide-based photovoltaic devices.

Strengthened Surface Modification for High-Performance Inorganic Perovskite Solar Cells with 21.3% Efficiency.

Metal halide inorganic perovskites show excellent thermal stability compared to organic-inorganic perovskites. However, the performance of inorganic perovskite solar cells (PSCs) is far from theoretical values, together with unsatisfactory stability, mainly due to the poor interfacial properties. In this work, a facial but effective method is reported to realize high-performance inorganic PSCs by post-modifying the perovskite surface with 2-thiophene ethylamine (TEA). It is found that amine group from TEA can favorably interact with the undercoordinated Pb2+ via Lewis acid-based coordination, while thiophene ring with electron-rich sulfur assists such interaction by functioning as an electron donor. The synergetic interaction allows TEA to passivate perovskite film defects more efficiently, as compared to phenethylamine (PEA) with less electron-donating ability. Moreover, perovskite valence band is slightly upward shift to match with hole transport material and facilitate hole transfer. These combinations result in a reduced non-radiative charge recombination and improved charge carrier lifetime. Consequently, PSCs with TEA modification shows a drastic improvement of VOC by 54 mV, yielding a champion PCE of 21.3%, much higher than the control PSCs (19.3%), along with improved ambient stability. This work demonstrates that surface modifier with an electron-rich moiety is critical for achieving efficient and stable inorganic PSCs.