Chloroform-infiltrated photonic crystal fiber with high-temperature sensitivity.

The temperature sensor is the core part of the temperature measurement instrument, and its performance directly determines the temperature measurement accuracy. Photonic crystal fiber (PCF) is a new type of temperature sensor with extremely high potential. In this paper, we propose a high-performance, structurally simple, liquid-filled PCF temperature sensor, which is based on a SMF-PCF-SMF (single mode fiber, SMF) sandwich structure. By adjusting the structural parameters of the the PCF, it is possible to obtain optical properties that are superior to those of ordinary optical fibers. This allows for more obvious responsive changes of the fiber transmission mode under small external temperature changes. By optimizing the basic structure parameters, a new PCF structure with a central air hole is designed, and its temperature sensitivity is -0.04696 nm/°C. When filling the air holes of PCFs with temperature-sensitive liquid materials, the response of the optical field against the temperature fluctuations can be effectively enhanced. The Chloroform solution is used to selectively infiltrate the resulting PCF owing to its large thermo-optical coefficient. After comparing various filling schemes, the calculation results show that the highest temperature sensitivity of -15.8 nm/°C is finally realized. The designed PCF sensor has a simple structure, high-temperature sensitivity, and good linearity showing great application potential.

Rapid calculation method for backscattered light of a space gravitational-wave detection telescope.

Stray light is a key issue that must be considered in the TianQin telescope. To solve the problem of a long simulation time and the inability of the simulation results to be fed back to guide the optical design, we propose a fast estimation method for stray light based on the FOV with high accuracy. Compared to other models, the error between our model and the software simulation results is smaller, within one order of magnitude. Based on this method, we obtain the optical component target of the TianQin telescope and propose an optimization method to reduce stray light, which can be verified by analyzing the optimized optical design.

Micropollutant removal and disinfection byproduct control by sequential peroxymonosulfate-UV treatment in water: A case study with sulfamethoxazole.

UV/peroxymonosulfate (UV/PMS) advanced oxidation process has attracted significant attention for removal of micropollutants in water. However, during practical water treatment applications, the PMS treatment must be performed before the UV treatment to achieve full contact. In this study, sulfamethoxazole (SMX) was selected as the target micropollutant. Four different operational approaches, including UV alone, PMS alone, simultaneous UV/PMS and sequential PMS-UV, were compared for their differences in SMX removal and disinfection by-product (DBP) formation potentials during chlorine-driven disinfection. Among the four approaches, UV/PMS and PMS-UV achieved over 90% removal efficiencies for SMX without substantial differences. For raw water, the trichloronitromethane (TCNM) formation potential after treatment with PMS-UV was lower than that after UV/PMS treatment. The time interval over which the PMS-UV process was conducted had little effect on the final removal efficiency for SMX. However, a brief (5 min) pre-PMS treatment significantly reduced the TCNM formation potential and the genotoxicity from DBPs. The formation risk for TCNM during chlorination increased markedly with increasing PMS dosages, and the appropriate dosage under these experimental conditions was suggested to be 0.5-1.0 mmol/L. Under alkaline conditions, PMS-UV treatment can enhance SMX degradation as well as dramatically reduced the formation potentials for haloketones, haloacetonitriles and halonitromethanes. This study suggests that proper optimization of UV/PMS processes can remove SMX and reduce its DBP formation.

Enhanced 2-MIB degradation by UV-LED/chlorine process: reaction kinetics, wavelength dependence, influencing factors and degradation pathways.

The efficient removal of 2-Methylisoborneol (2-MIB), a typical odour component, in water treatment plants (WTPs), poses a great challenge to conventional water treatment technology due to its chemical stability. In this study, the combination of ultraviolet light-emitting diode (UV-LED) and chlorine (UV-LED/chlorine) was exploited for 2-MIB removal, and the role of ultraviolet (UV) wavelength was investigated systematically. The results showed that UV or chlorination alone did not degrade 2-MIB effectively, and the UV/chlorine process could degrade 2-MIB efficiently, following the pseudo-first-order kinetic model. The 275 nm UV exhibited higher 2-MIB degradation efficiency in this UV-LED/chlorine system than 254 nm UV, 265 nm UV and 285 nm UV due to the highest mole adsorption coefficient and quantum yield of chlorine in 275 nm UV. ·OH and ·Cl produced in the 275 nm UV/chlorine system played major roles in 2-MIB degradation. HCO3- and Natural organic matter (NOM), prevalent in water, consumed ·OH and ·Cl, thus inhibiting the 2-MIB degradation by UV-LED/chlorine. In addition, NOM and 2-MIB could form a photonic competition effect. The degradation of 2-MIB by UV-LED/chlorine was done mainly through dehydration and demethylation, and odorous intermediates, such as camphor, were produced. 2-MIB was degraded through the α bond fracture and six-membered ring opening to form saturated or unsaturated hydrocarbons and aldehydes. Four DBPs, chloroform (CF), trichloroacetaldehyde (TCE), trichloroacetone (TCP) and dichloroacetone (DCP), were mainly generated, and CF was the most significant by-product.

Wavelength dependency and photosensitizer effects in UV-LED photodegradation of iohexol.

Iodinated X-ray contrast media (ICM) are ubiquitously present in water sources and challenging to eliminate using conventional processes, posing a significant risk to aquatic ecosystems. Ultraviolet light-emitting diodes (UV-LED) emerge as a promising technology for transforming micropollutants in water, boasting advantages such as diverse wavelengths, elimination of chemical additives, and no induction of microorganisms' resistance to disinfectants. The research reveals that iohexol (IOX) degradation escalates as UV wavelength decreases, attributed to enhanced photon utilization efficiency. Pseudo-first-order rate constants (kobs) were determined as 3.70, 2.60, 1.31 and 0.65 cm2 J-1 at UV-LED wavelengths of 255, 265, 275 and 285 nm, respectively. The optical properties of dissolved organic matter (DOM) and anions undeniably influence the UV-LED photolysis process through photon competition and the generation of reactive substances. The influence of Cl- on IOX degradation was insignificant at UV-LED 255, but it promoted IOX degradation at 265, 275 and 285 nm. IOX degradation was accelerated by ClO2-, NO3-and HA due to the formation of various reactive species. In the presence of NO3-, the kobs of IOX followed the order: 265 > 255 > 275 > 285 nm. Photosensitizers altered the spectral dependence of IOX, and the intermediate photoactivity products were detected using electron spin resonance. The transformation pathways of IOX were determined through density functional theory calculations and experiments. Disinfection by-products (DBPs) yields of IOX during UV-LED irradiation decreased as the wavelength increased: 255 > 265 > 275 > 285 nm. The cytotoxicity index value decreased as the UV-LED wavelength increased from 255 to 285 nm. These findings are crucial for selecting the most efficient wavelength for UV-LED degradation of ICM and will benefit future water purification design.