Alkaline degradation study of linear and network poly(ε-caprolactone).

Alkaline hydrolysis of a polycaprolactone (PCL) network obtained by photopolymerization of a PCL macromer was investigated. The PCL macromer was obtained by the reaction of PCL diol with methacrylic anhydride. Degradation of PCL network is much faster than linear PCL; the weight loss rate is approximately constant until it reaches around 70%, which happens after approximately 60 h in PCL network and 600 h in linear PCL. Calorimetric results show no changes in crystallinity throughout degradation, suggesting that it takes place in the crystalline and amorphous phases simultaneously. Scanning electron microscopy microphotographs indicate that degradation is produced by a different erosion mechanism in both kinds of samples. The more hydrophilic network PCL would follow a bulk-erosion mechanism, whereas linear PCL would follow a surface-erosion mechanism. Mechanical testing of degraded samples shows a decline in mechanical properties due to changes in sample porosity as a consequence of the degradation process.

Regenerative and Resorbable PLA/HA Hybrid Construct for Tendon/Ligament Tissue Engineering.

Tendon and ligament shows extremely limited endogenous regenerative capacity. Current treatments are based on the replacement and or augmentation of the injured tissue but the repaired tissue rarely achieve functionality equal to that of the preinjured tissue. To address this challenge, tissue engineering has emerged as a promising strategy. This study develops a regenerative and resorbable hybrid construct for tendon and ligament engineering. The construct is made up by a hollow poly-lactic acid braid with embedded microspheres carrying cells and an anti-adherent coating, with all the parts being made of biodegradable materials. This assembly intends to regenerate the tissue starting from the interior of the construct towards outside while it degrades. Fibroblasts cultured on poly lactic acid and hyaluronic acid microspheres for 6 h were injected into the hollow braid and the construct was cultured for 14 days. The cells thus transported into the lumen of the construct were able to migrate and adhere to the braid fibers naturally, leading to a homogeneous proliferation inside the braid. Moreover, no cells were found on the outer surface of the coating. Altogether, this study demonstrated that PLA/HA hybrid construct could be a promising material for tendon and ligament repair.

Positioning of the cross-stitch on the modified Kessler core tendon suture.

Cryopreserved human tendons were sutured with different variations of a modified Kessler-type grasping suture in a series of different designs in order to assess the influence of the distance between the cross-stitch on the core suture (5 and 10 mm from the cut tendon edge) on the peripheral suture. An original mathematical model was employed to explain the mechanical behavior (strength, deformation, and distribution of load) of the different suture designs. The effect of the peripheral epitendinous suture, combined with the distance of the core suture, was evaluated. The variation of core suture distance had no relevant consequences on the overall resilience of the design. However, increasing the distance between the cross-stitches of the core suture reduces the deformation that is absorbed not only by the core suture itself but also by the peripheral suture. Adding a peripheral epitendinous suture to a 10-mm design almost doubles the breaking load in absolute values. The mathematical model predicts that the peripheral suture will support a greater load when the distance of the core suture cross-stitches is increased. The evidence level is II.

Biodegradable polycaprolactone scaffold with controlled porosity obtained by modified particle-leaching technique.

Scaffold with controlled porosity constitute a cornerstone in tissue engineering, as a physical support for cell adhesion and growth. In this work, scaffolds of polycaprolactone were synthesized by a modified particle leaching method in order to control porosity and pore interconnectivity; the aim is to observe their influence on the mechanical properties and, in the future, on cell adhesion and proliferation rates. Low molecular weight PEMA beads with an average size of 200 microm were sintered with various compression rates in order to obtain the templates (negatives of the scaffolds). Then the melt polycaprolactone was injected into the porous template under nitrogen pressure in a custom made device. After cooling and solidifying of the melt polymer, the porogen was removed by selective dissolution in ethanol. The porosity and morphology of the scaffold were studied as well as the mechanical properties. Porosities from 60% to 85% were reached; it was found that pore interconnectivity logically increases with increasing porosity, and that mechanical strength decreases with increasing porosity. Because of their interesting properties and interconnected structure, these scaffolds are expected to find useful applications as a cartilage or bone repair material.