The Impact of Modeling Liquids on Surface Roughness and Color Properties of Bulkfill Resin Composites After Simulated Tooth Brushing: An in Vitro Study. Part I.

OBJECTIVE: To evaluate the effect of different modeling agents on color changes, surface roughness, and translucency parameters over time in Bulkfill resin composites. MATERIAL AND METHODS: Sixty specimens were prepared using three Bulkfill resin composites (Tetric N-Ceram Bulkfill, Filtek One Bulkfill and Opus Bulkfill) and three modeling agents (Wetting Resin, Optibond FL and Ambar APS). All specimens were subjected to a simulated tooth-brushing (Baseline, 50.000 cycles, 100.000 cycles), and surface roughness was measured at each interval. Surface topography was evaluated. The translucency parameter and color changes were assessed after 24-h, 7-, 14- and 30-day immersion in water, wine, and coffee. Data was analyzed using ANOVA and Bonferroni test. RESULTS: All specimens increased roughness after simulated tooth-brushing (p < 0.05). Wetting Resin decreased roughness on Tetric N-Ceram Bulkfill (p < 0.05). The translucency parameter remained unaltered for all groups. All groups changed color after 30-days of immersion in wine and coffee (p < 0.05). Ambar APS and Wetting Resin on Tetric N-Ceram Bulkfill showed higher color changes when immersed in coffee (p < 0.05). CONCLUSION: The use of modeling agents does not jeopardize translucency properties but may affect surface roughness and color properties of Bulkfill resin composites depending on their composition. CLINICAL SIGNIFICANCE: The findings of this study suggest that surface roughness and color properties are affected by the differences in the composition between modeling agents and Bulkfill resins composites.

Assessment of the effect of experimental bleaching agent with nano-bioactive material on postoperative sensitivity: A randomized, triple blind clinical trial.

OBJECTIVES: This clinical study aimed to evaluate the effect of incorporating bioactive nanoparticles (n-Bm) inside an in-office bleaching gel on the risk and intensity of tooth sensitivity (TS) and on bleaching effectiveness. MATERIALS AND METHODS: Sixty-six participants were selected and randomly assigned into two groups: control-only in-office gel and experimental-in-office gel with n-Bm. Teeth were bleached in two sessions (3 × 15-min). TS was recorded using a VAS and NRS. The color change was evaluated by subjective (VITA Classical and VITA Bleachedguide) and objective (Easyshade spectrophotometer) methods at baseline and 30 days after the end of treatment. The TS was evaluated by McNemar, Wilcoxon Signed Rank, and paired t test. The color changes between groups were compared using paired t test (α = 0.05). RESULTS: No significant differences between the groups were observed in the risk (control = 27% [95%IC 18-39]; experimental = 21% [95%IC 13-32]) and intensity of TS, as well as in the color change (p >0.05) for any color measurement. CONCLUSION: The inclusion of n-Bm into the bleaching agents did not affect the whitening effectiveness, as well as the risk and intensity of TS between groups. However, the results of the absolute risk of TS were low for both in-office gels used. CLINICAL SIGNIFICANCE: Despite no significant differences between groups, both experimental bleaching agents present suitable results with low values for TS.

Influence of flavonoids on long-term bonding stability on caries-affected dentin.

OBJECTIVES: To evaluate the effect of experimental dentin pre-treatment solutions formulated with different flavonoids on microtensile bond strength (µTBS), nanohardness (NH) and ultra-morphological characteristics of artificial caries-affected dentin (CAD) bonded using a universal bonding system. METHODS: A microbiological method was used to create an artificial CAD in 91 human molars. Five experimental pre-treatment solutions were created using the following flavonoids: quercetin (QUE); hesperidin (HES); rutin (RUT); naringin (NAR), or proanthocyanidin (PRO). A placebo solution (PLA) with no flavonoids added was also evaluated. The flavonoids or placebo solutions were applied to the CAD prior to the application and photoactivation of a universal adhesive (Scotchbond Universal, 3M Oral Care). A control group (CON), in which only the bonding agent was applied without any flavonoid solution, was also evaluated. A 3-mm-thick block of resin composite (Opallis, FGM) was built up on the flat bonded CAD surfaces and was light-cured following the manufacturer's instructions. Specimens were sectioned to obtain resin-dentin slices and sticks (cross-sectional area of 0.8 mm2). The µTBS, NH, and confocal ultramorphology analysis of resin-dentin interface was evaluated at 24 h and after thermo-cycling aging (25,000 cycles). The results were analyzed using 2-way ANOVA followed by Bonferroni's post hoc test (pre-set α = 0.05). RESULTS: The specimens from groups QUE, NAR, and RUT presented greater µTBS values than those from CON group (p<0.05). Specimens from some of these experimental groups presented greater nanomechanical properties (p<0.05), and no morphological degradation at the resin-dentin interface after aging. SIGNIFICANCE: The use of exogenous cross-linkers as dentin pre-treatment before bonding procedures may represent a suitable strategy to improve the longevity of universal adhesive systems applied to caries-affected dentin.