Simultaneous Monitoring of Crystalline Active Materials and Resistance Evolution in Lithium-Sulfur Batteries.

Operando X-ray diffraction (XRD) is a valuable tool for studying secondary battery materials as it allows for the direct correlation of electrochemical behavior with structural changes of crystalline active materials. This is especially true for the lithium-sulfur chemistry, in which energy storage capability depends on the complex growth and dissolution kinetics of lithium sulfide (Li2S) and sulfur (S8) during discharge and charge, respectively. In this work, we present a novel development of this method through combining operando XRD with simultaneous and continuous resistance measurement using an intermittent current interruption (ICI) method. We show that a coefficient of diffusion resistance, which reflects the transport properties in the sulfur/carbon composite electrode, can be determined from analysis of each current interruption. Its relationship to the established Warburg impedance model is validated theoretically and experimentally. We also demonstrate for an optimized electrode formulation and cell construction that the diffusion resistance increases sharply at the discharge end point, which is consistent with the blocking of pores in the carbon host matrix. The combination of XRD with ICI allows for a direct correlation of structural changes with not only electrochemical properties but also energy loss processes at a nonequilibrium state and, therefore, is a valuable technique for the study of a wide range of energy storage chemistries.

On the Elusive Crystallography of Lithium-Rich Layered Oxides: Novel Structural Models.

Lithium-rich layered oxides (LRLOs) are one of the most attractive families among future positive electrode materials for the so-called fourth generation of lithium-ion batteries (LIBs). Their electrochemical performance is enabled by the unique ambiguous crystal structure that is still not well understood despite decades of research. In the literature, a clear structural model able to describe their crystallographic features is missing thereby hindering a clear rationalization of the interplay between synthesis, structure, and functional properties. Here, the structure of a specific LRLO, Li1.28 Mn0.54 Ni0.13 Co0.02 Al0.03 O2 , using synchrotron X-ray diffraction (XRD), neutron diffraction (ND), and High-Resolution Transmission Electron Microscopy (HR-TEM), is analyzed. A systematic approach is applied to model diffraction patterns of Li1.28 Mn0.54 Ni0.13 Co0.02 Al0.03 O2 by using the Rietveld refinement method considering the R 3 ¯ $\bar{3}$ m and C2/m unit cells as the prototype structures. Here, the relative ability of a variety of structural models is compared to match the experimental diffraction pattern evaluating the impact of defects and supercells derived from the R 3 ¯ $\bar{3}$ m structure. To summarize, two possible models able to reconcile the description of experimental data are proposed here for the structure of Li1.28 Mn0.54 Ni0.13 Co0.02 Al0.03 O2 : namely a monoclinic C2/m defective lattice (prototype Li2 MnO3 ) and a monoclinic defective supercell derived from the rhombohedral R 3 ¯ $\bar{3}$ m unit cell (prototype LiCoO2 ).

Diagnosing the Electrostatic Shielding Mechanism for Dendrite Suppression in Aqueous Zinc Batteries.

Aqueous zinc electrolytes offer the potential for cheaper rechargeable batteries due to their safe compatibility with the high capacity metal anode; yet, they are stymied by irregular zinc deposition and consequent dendrite growth. Suppressing dendrite formation by tailoring the electrolyte is a proven approach from lithium batteries; yet, the underlying mechanistic understanding that guides such tailoring does not necessarily directly translate from one system to the other. Here, it is shown that the electrostatic shielding mechanism, a fundamental concept in electrolyte engineering for stable metal anodes, has different consequences for the plating morphology in aqueous zinc batteries. Operando electrochemical transmission electron microscopy is used to directly observe the zinc nucleation and growth under different electrolyte compositions and reveal that electrostatic shielding additive suppresses dendrites by inhibiting secondary zinc nucleation along the (100) edges of existing primary deposits and encouraging preferential deposition on the (002) faces, leading to a dense and block-like zinc morphology. The strong influence of the crystallography of Zn on the electrostatic shielding mechanism is further confirmed with Zn||Ti cells and density functional theory modeling. This work demonstrates the importance of considering the unique aspects of the aqueous zinc battery system when using concepts from other battery chemistries.

Combined Stabilizing of the Solid-Electrolyte Interphase with Suppression of Graphite Exfoliation via Additive-Solvent Optimization in Li-Ion Batteries.

Propylene carbonate (PC) is a promising solvent for extending the operating temperature range for lithium-ion batteries (LIBs) because of its high dielectric constant and wide temperature range stability. However, PC can cause graphite exfoliation through cointercalation, leading to electrolyte decomposition and subsequent irreversible capacity loss. This work reports the formulation of a ternary electrolyte with the introduction of an inorganic salt additive, potassium hexafluorophosphate (KPF6), to address the aforementioned concerns. We demonstrate the cumulative effect of solvent and additive on delivering multiple performance benefits and safety of the battery. The faster diffusion rate of K + solvation shell decreases the rate of PC decomposition, thereby reducing its cointercalation. Additionally, the optimum concentration of KPF6, i.e., 0.1 M constructs a robust and insoluble LiF-rich electrode/electrolyte interphase, further suppressing graphite exfoliation and Li dendrite formation. The stable cyclability is achieved by enhanced Li + transportation through the LiF-rich interphase, enabling an exfoliation-free and dendrite-free graphite anode in the ternary electrolyte.

Rapid determination of solid-state diffusion coefficients in Li-based batteries via intermittent current interruption method.

The galvanostatic intermittent titration technique (GITT) is considered the go-to method for determining the Li+ diffusion coefficients in insertion electrode materials. However, GITT-based methods are either time-consuming, prone to analysis pitfalls or require sophisticated interpretation models. Here, we propose the intermittent current interruption (ICI) method as a reliable, accurate and faster alternative to GITT-based methods. Using Fick's laws, we prove that the ICI method renders the same information as the GITT within a certain duration of time since the current interruption. Via experimental measurements, we also demonstrate that the results from ICI and GITT methods match where the assumption of semi-infinite diffusion applies. Moreover, the benefit of the non-disruptive ICI method to operando materials characterization is exhibited by correlating the continuously monitored diffusion coefficient of Li+ in a LiNi0.8Mn0.1Co0.1O2-based electrode to its structural changes captured by operando X-ray diffraction measurements.

Synthesis of Li1.20Mn0.432+Nb0.39O2 disordered rock-salt under reducing conditions for Li-ion batteries.

A Mn2+-Li-Nb disordered rock-salt oxide cathode is prepared by a solid-state reaction under 5% H2/N2, and its electrochemical property shows a high voltage plateau at 4.8 V, with irreversible structural changes in the 1st cycle due to O redox processes; this is supported by powder X-ray diffraction and ex situ laboratory Mn K-edge XANES data.

Synthesis-structure relationships in Li- and Mn-rich layered oxides: phase evolution, superstructure ordering and stacking faults.

Li- and Mn-rich layered oxides are promising positive electrode materials for future Li-ion batteries. The presence of crystallographic features such as cation-mixing and stacking faults in these compounds make them highly susceptible to synthesis-induced structural changes. Consequently, significant variations exist in the reported structure of these compounds that complicate the understanding of how the crystallographic structure influences its properties. This work investigates the synthesis-structure relations for three widely investigated Li- and Mn-rich layered oxides: Li2MnO3, Li1.2Mn0.6Ni0.2O2 and Li1.2Mn0.54Ni0.13Co0.13O2. For each compound, the average structure is compared between two synthetic routes of differing degrees of precursor mixing and four annealing protocols. Furthermore, thermodynamic and synthesis-specific kinetic factors governing the equilibrium crystallography of each composition are considered. It was found that the structures of these compounds are thermodynamically metastable under the synthesis conditions employed. In addition to a driving force to reduce stacking faults in the structure, these compositions also exhibited a tendency to undergo structural transformations to more stable phases under more intense annealing conditions. Increasing the compositional complexity introduced a kinetic barrier to structural ordering, making Li1.2Mn0.6Ni0.2O2 and Li1.2Mn0.54Ni0.13Co0.13O2 generally more faulted relative to Li2MnO3. Additionally, domains with different degrees of faulting were found to co-exist in the compounds. This study offers insight into the highly synthesis-dependent subtle structural complexities present in these compounds and complements the substantial efforts that have been undertaken to understand and optimise its electrochemical properties.

Surface Reduction Stabilizes the Single-Crystalline Ni-Rich Layered Cathode for Li-Ion Batteries.

The surface of the layered transition metal oxide cathode plays an important role in its function and degradation. Modification of the surface structure and chemistry is often necessary to overcome the debilitating effect of the native surface. Here, we employ a chemical reduction method using CaI2 to modify the native surface of single-crystalline layered transition metal oxide cathode particles. High-resolution transmission electron microscopy shows the formation of a conformal cubic phase at the particle surface, where the outmost layer is enriched with Ca. The modified surface significantly improves the long-term capacity retention at low rates of cycling, yet the rate capability is compromised by the impeded interfacial kinetics at high voltages. The lack of oxygen vacancy generation in the chemically induced surface phase transformation likely results in a dense surface layer that accounts for the improved electrochemical stability and impeded Li-ion diffusion. This work highlights the strong dependence of the electrode's (electro)chemical stability and intercalation kinetics on the surface structure and chemistry, which can be further tailored by the chemical reduction method.

Moisture-Driven Degradation Pathways in Prussian White Cathode Material for Sodium-Ion Batteries.

The high-theoretical-capacity (∼170 mAh/g) Prussian white (PW), NaxFe[Fe(CN)6]y·nH2O, is one of the most promising candidates for Na-ion batteries on the cusp of commercialization. However, it has limitations such as high variability of reported stable practical capacity and cycling stability. A key factor that has been identified to affect the performance of PW is water content in the structure. However, the impact of airborne moisture exposure on the electrochemical performance of PW and the chemical mechanisms leading to performance decay have not yet been explored. Herein, we for the first time systematically studied the influence of humidity on the structural and electrochemical properties of monoclinic hydrated (M-PW) and rhombohedral dehydrated (R-PW) Prussian white. It is identified that moisture-driven capacity fading proceeds via two steps, first by sodium from the bulk material reacting with moisture at the surface to form sodium hydroxide and partial oxidation of Fe2+ to Fe3+. The sodium hydroxide creates a basic environment at the surface of the PW particles, leading to decomposition to Na4[Fe(CN)6] and iron oxides. Although the first process leads to loss of capacity, which can be reversed, the second stage of degradation is irreversible. Over time, both processes lead to the formation of a passivating surface layer, which prevents both reversible and irreversible capacity losses. This study thus presents a significant step toward understanding the large performance variations presented in the literature for PW. From this study, strategies aimed at limiting moisture-driven degradation can be designed and their efficacy assessed.

Influence of Synthesis Routes on the Crystallography, Morphology, and Electrochemistry of Li2MnO3.

With the potential of delivering reversible capacities of up to 300 mAh/g, Li-rich transition-metal oxides hold great promise as cathode materials for future Li-ion batteries. However, a cohesive synthesis-structure-electrochemistry relationship is still lacking for these materials, which impedes progress in the field. This work investigates how and why different synthesis routes, specifically solid-state and modified Pechini sol-gel methods, affect the properties of Li2MnO3, a compositionally simple member of this material system. Through a comprehensive investigation of the synthesis mechanism along with crystallographic, morphological, and electrochemical characterization, the effects of different synthesis routes were found to predominantly influence the degree of stacking faults and particle morphology. That is, the modified Pechini method produced isotropic spherical particles with approximately 57% faulting and the solid-state samples possessed heterogeneous morphology with approximately 43% faulting probability. Inevitably, these differences lead to variations in electrochemical performance. This study accentuates the importance of understanding how synthesis affects the electrochemistry of these materials, which is critical considering the crystallographic and electrochemical complexities of the class of materials more generally. The methodology employed here is extendable to studying synthesis-property relationships of other compositionally complex Li-rich layered oxide systems.