Fibrin Glue and Conduit Form a Composite Structure in Digital Nerve Repair.

Repair of severed nerves without autograft or allograft has included suture, suture with glue alone, suture with conduit and suture with glue augmentation to conduit, where use of conduit is considered for separation of the nerve ends from 5 mm to 3 cm. Repairs must not only serve acutely to provide apposition of nerve ends but must enable the healing of the nerve. Using biological conduit can place suture at the ends of the conduit while fibrin glue alone eliminates suture but with limited strength. The combination of conduit and glue offers the growth guidance of conduit with sufficient strength from the glue to maintain the nerve within the conduit. The role of fibrin glue in the integrity of the repair remains an open question, however. We sought to determine the factors in the strength of a glue-conduit-nerve construct and include consideration of standard suture repair. Fresh-frozen cadaveric digital nerves were repaired with suture alone, with glue alone or with suture and glue together and then loaded to failure. Previously tested specimens with conduit, suture and glue were considered for comparison. The suture alone (2.02 N) and suture with glue (2.24 N) were not statistically different from each other but were statistically stronger than glue alone (0.15 N). When compared to the earlier results of the strength of conduit with glue (0.65 N), these simple results show that the glue and conduit act together. The increased area over which the glue adheres to the nerve and conduit creates a composite structure stronger than either alone.

Biomechanical Response to Distraction of Hip Capsular Reconstruction With Human Acellular Dermal Patch Graft.

PURPOSE: To quantify the biomechanical properties of the hip capsule with human dermal allograft reconstruction to determine whether a dermal patch restored capsular resistance to distraction. METHODS: Nine cadaveric hip specimens were dissected until capsule and bony structures remained and were then mounted in a testing fixture in neutral flexion and abduction. Four states of the hip capsule were sequentially tested under axial distraction of 5 mm measured with video analysis and with resultant force measurement: (1) intact hip capsule, (2) interportal capsulotomy, (3) capsulectomy to the zona orbicularis, and (4) capsular reconstruction with human dermal allograft using acetabular anchors and capsule-to-patch sutures. RESULTS: Capsulectomy was different from intact (P = .036), capsulotomy differed from capsulectomy (P = .012), and the repair was statistically significantly different from capsulectomy (P = .042); intact and reconstructed cases were not statistically significantly different. The force required for 5 mm of distraction decreased after interportal capsulotomy by an average of 9% compared with the intact state and further decreased after capsulectomy by 30% compared with the intact state. After capsular reconstruction using dermal allograft, force requirements increased by an average of 36% from the capsulectomy state, only 5% below the intact state. CONCLUSIONS: Human dermal allograft tissue graft provides restoration of distractive strength for use during hip capsule reconstruction with acetabular anchor fixation and distal soft-tissue fixation after capsulectomy in a cadaveric model. CLINICAL RELEVANCE: Capsular repair or reconstruction with a dermal patch offers time-zero restoration of function; intact and reconstructed cases showed no difference, and reconstruction restored a capsulectomy to a biomechanical equivalent of the intact case when distraction was applied.

The moving valgus stress test produces more ulnar collateral ligament change in length during extension than during flexion: a biomechanical study.

HYPOTHESIS AND BACKGROUND: Injuries to the elbow medial ulnar collateral ligament (mUCL) pose a diagnostic challenge, with the moving valgus stress test (MVST) currently accepted as the gold-standard clinical test. This study sought to biomechanically evaluate the change in length of the ulnar collateral ligament (UCL) during flexion-extension using a null hypothesis that the mUCL will not experience a greater change in length with movement than with static loading. METHODS: Seven fresh-frozen human cadaveric elbows were tested with static and dynamic valgus stress. We measured (1) ligament length with a multi-camera optical system, (2) elbow flexion with an incremental encoder, and (3) valgus deviation with an electronic inclinometer. With a force applied to the wrist to simulate a clinical stress examination, the elbow was flexed and extended in a physiological elbow simulator to mimic the flexion and extension of the MVST. RESULTS: The simulated MVST produced more elongation of the UCL compared with static stress testing (P < .001). Ninety degrees of flexion produced the highest mean change, and the anterior and posterior bands demonstrated different length change characteristics. Comparison of dynamic flexion and extension showed a statistically significant difference in change in length: The mUCL reached the greatest change during extension, with the greatest changes during extension near 90° of flexion. DISCUSSION AND CONCLUSION: The MVST produces significantly more elongation of the mUCL than either a static test or a moving test in flexion. This study provides biomechanical evidence of the validity of the MVST as a superior examination technique for injuries to the UCL.

Clinical and functional impairment after nonoperative treatment of distal biceps ruptures.

BACKGROUND: Clinical and functional impairment after nonoperative treatment of distal biceps ruptures is not well understood. The goal of this study was to measure patients' perceived disability, kinematic adjustment, and forearm supination power after nonoperative treatment of distal biceps ruptures. METHODS: Fourteen individuals after nonoperative treatment of distal biceps ruptures were matched to a control group of 18 uninjured volunteers. Both groups prospectively completed the Disabilities of the Arm, Shoulder and Hand (DASH), Single Assessment Numerical Evaluation (SANE), and Biceps Disability Questionnaire. Both performed a new timed isotonic supination test that was designed to simulate activities of daily life. The isotonic torque dynamometer measures the supination arc, center of supination arc, torque, angular velocity, and power. Motion analysis quantifies forearm and shoulder contributions to the arc of supination. RESULTS: The nonoperative treated group's DASH (23.2 ± 10.3) and SANE (59.6 ± 16.2) scores demonstrated a clinical meaningful impairment. The control group showed no significant differences in kinematic values between dominant and nondominant arms (P = .854). The nonoperative biceps ruptured arms, compared with their uninjured arms, changed supination motion by decreasing the supination arc (P ≤ .036), shifting the center of supination arc to a more pronated position (P ≤ .030), and increasing the shoulder contribution to rotation (P ≤ .001); despite this adaptation, their average corrected power of supination decreased by 47% (P = .001). CONCLUSION: Patients should understand that nonoperative treatment for distal biceps ruptures will result in varying degrees of functional loss as measured by the DASH, SANE, and Biceps Disability Questionnaire, change their supination kinematics during repetitive tasks, and that they will lose 47% of their supination power.

Single-screw Fixation of Adolescent Salter-II Proximal Humeral Fractures: Biomechanical Analysis of the "One Pass Door Lock" Technique.

BACKGROUND: Pin fixation of Salter-II proximal humeral fractures in adolescents approaching skeletal maturity has potential complications that can be avoided with single-screw fixation. However, the strength of screw fixation relative to parallel and diverging pin fixation is unknown. To compare the biomechanical fixation strength between these fixation modalities, we used synthetic composite humeri, and then compared these results in composite bone with cadaveric humeri specimens. METHODS: Parallel pinning, divergent pinning, and single-screw fixation repairs were performed on synthetic composite humeri with simulated fractures. Six specimens of each type were tested in axial loading and other 6 were tested in torsion. Five pair of cadaveric humeri were tested with diverging pins and single screws for comparison. RESULTS: Single-screw fixation was statistically stronger than pin fixation in axial and torsional loading in both composite and actual bone. There was no statistical difference between composite and cadaveric bone specimens. CONCLUSION: Single-screw fixation can offer greater stability to adolescent Salter-II fractures than traditional pinning. CLINICAL RELEVANCE: Single-screw fixation should be considered as a viable alternative to percutaneous pin fixation in transitional patients with little expected remaining growth.

Quadrupled Hamstring Graft Strength as a Function of Clinical Sizing.

PURPOSE: This study sought to compare the strength of quadrupled hamstring tendon (QHT) grafts of 6 to 9.5 mm in clinical diameter with that of 10-mm bone-patellar tendon-bone (BPTB) grafts. METHODS: Twenty cadaveric semitendinosus and gracilis tendons were combined into QHT grafts. These were sized using a standard graft-sizing device and an area micrometer, yielding grafts ranging from 6 to 9.5 mm in diameter. The grafts were tested to failure. Five 10-mm BPTB grafts were also sized and tested. RESULTS: Clinical sizing did predict the strength of the graft but not profoundly. As a material alone, without consideration of fixation in bone tunnels, QHT grafts were stronger than BPTB grafts. Graft strength decreased with size, but a linear relation between strength and diameter (r(2) = 0.715, P < .001) was found to be as good as the expected quadratic fit (r(2) = 0.709). Compared with BPTB grafts, even the smallest QHT grafts (diameter <6.5 mm) were still significantly stronger than 10-mm BPTB grafts (P = .004). The elastic moduli of the QHT and BPTB grafts were 761 ± 187 MPa and 615 ± 403 MPa, respectively; elongations at failure were 12.0% ± 2.0% and 7.5% ± 1.6%, respectively; and failure stresses were 105 ± 18 MPa and 50 ± 14 MPa, respectively. CONCLUSIONS: This work shows that a clinical size of QHT grafts of 6 mm in diameter is not a concern regarding the strength itself. For a possible lower-end prediction of acceptable size, assuming that a gracilis-semitendinosus graft would have only the stress of the weakest measured QHT graft of 88 MPa, a graft of 5.5 mm in diameter would suffice, having more strength in newtons than the average patellar tendon. CLINICAL RELEVANCE: Clinically sized QHT grafts have a higher failure strength than 10-mm patellar tendon grafts. Therefore the strength of the graft cannot account for the higher clinical failure rates of smaller hamstring grafts in active patients in clinical studies.

Factors affecting supination strength after a distal biceps rupture.

HYPOTHESIS: This study quantified pain (visual analog pain scale [VAPS]), disability (Disabilities of the Arm, Shoulder and Hand [DASH]) and isometric supination torque at 3 forearm positions in a prospective cohort of biceps-deficient arms to assess the potential for functional return with nonoperative treatment. MATERIALS AND METHODS: Twenty-three men (50 ± 11 years) with complete unilateral distal biceps avulsion underwent isometric supination strength testing of both limbs at 60° of supination, 0° (neutral), and 60° of pronation. After exclusion of 1 outlier patient, the mean time from injury to evaluation was 44 days (range, 4-455 days). Pain level (VAPS) and functional outcome (DASH) were assessed; supination strength was normalized to the uninjured arm. RESULTS: The uninjured arm was stronger (P < .001), and peak torque varied with forearm position (P < .043). Peak torque was greater in pronation compared with supination, regardless of injury (P < .002). No differences were detected in supination strength as a result of forearm position or arm dominance. Supination strength did not correlate with time from injury to evaluation. One patient regained supination strength (115%) at 60° of pronation and 72% in neutral with a lengthy time from injury. VAPS (5 of 10) and DASH (39 of 100) scores decreased with time and did not relate to supination strength. CONCLUSION: Biceps tendon rupture led to a 60% decrease in supination strength in the neutrally oriented forearm. Peak torque observations can be explained using forearm moment arms. VAPS and DASH scores decreased with time but did not affect strength. We speculate that supination strength from pronation to neutral can improve as one strengthens the brachioradialis but strength deficits from neutral to supination are more difficult to overcome.

Effect of lesser tuberosity osteotomy size and repair construct during total shoulder arthroplasty.

BACKGROUND: Lesser tuberosity osteotomy has been shown to decrease postoperative subscapularis dysfunction. The purpose of this study was to determine the effect of osteotomy thickness and suture configuration on repair integrity. MATERIALS AND METHODS: One side of 12 matched-pair cadaveric shoulders was randomly assigned to either a thick osteotomy (100% of lesser tuberosity height) or a thin osteotomy (50% of height). Both sides of the matched pairs were given the same repair, either (1) compression sutures or (2) compression sutures plus 1 tension suture. This created 4 groups of 6 paired specimens. Computed tomography imaging was used to measure tuberosity dimensions before and after osteotomy to validate fragment height and area. The repairs were loaded cyclically and then loaded to failure. A video system measured fragment displacement. The percent area of osteotomy contact was calculated from the computed tomography and displacement data. RESULTS: The average initial displacement was less in the thin osteotomy groups (P = .011). Adding a tension suture negated this difference. A significant number of thin repair sites compared with thick repair sites remained intact during load-to-failure testing (P = .001). No difference occurred because of maximum load between the repair groups (P = .401), and construct stiffness was greater when a tension suture was used (P = .032). The percent area of osteotomy contact showed no differences between the osteotomy (P = .431) and repair (P = .251) groups. CONCLUSION: The study showed that thin osteotomies displaced less than thick osteotomies. Adding a tension band improved construct stability and eliminated some failure modes. Our ideal repair was a thin wafer with both tension and compression sutures. This construct had smaller total displacement, a high osteotomy percent contact area, and a high maximum load.

A Comparison of Imaging Outcomes From 2 Weightbearing CT Modalities.

BACKGROUND: The use of weightbearing images to diagnose foot and ankle injuries continues to offer hope for improved insight into pathologies, but weightbearing CT imaging has been limited by availability. The ability to apply force to the lower limb in a horizontal bore CT system may offer an adaptation to currently available imaging systems that provides access to weightbearing images without the acquisition of additional expensive imaging space or equipment. METHODS: In order to determine whether a horizontal CT system could produce the same results as a standing CT, 3 images of one foot from 10 subjects was obtained and standard measures were calculated. Each subject underwent a standing CT scan, a scan in a horizontal bore CT machine while the subject pressed against a pedal with spring resistance and a finally a scan with the foot placed on the pedal but without any pressure. RESULTS: No statistically significant difference between the standing and pedal-based CTs resulted. Navicular height and Meary angle (axial) were statistically different from nonweightbearing for both standing and horizontal systems. The horizontal results were statistically different from nonweightbearing in IM angle, talocalcaneal angle, and talonavicular coverage. No differences from nonweightbearing were found for either system in talar tilt, talocrural angle, or the lateral Meary angle. CONCLUSION: The results in this initial study of normal control subjects suggest that a pedal-based loading mechanism may adapt a horizontal-bore CT system for the acquisition of weightbearing images. CLINICAL RELEVANCE: The ability to acquire a weightbearing CT from a horizontal bore CT machine can make these images more available.

"Safe dissection parameters of the anconeus rotational flap for soft tissue coverage at the elbow".

Background: The anconeus is a small muscle located on the posterior elbow originating on the lateral epicondyle and inserting onto the proximal-lateral ulna that functions as an elbow extensor as well as dynamic stabilizer. The blood supply is tri-fold: medial/middle collateral artery (MCA), recurrent posterior interosseous artery (RPIA), and less commonly found, the posterior branch of the radial collateral artery. The anconeus has become a popular option for local soft tissue coverage about the elbow (distal triceps, olecranon, proximal forearm). The average defect size for consideration of local anconeus flap coverage is 5-7cm2. The aim of the study was to determine safe dissection parameters of the anconeus as well as map arterial pedicles to achieve successful local harvest of the muscle without devascularization. Materials and Methods: 8 fresh frozen cadaveric arms (all male, average age 63 years - 4 left arms, 4 right arms) from scapula to fingertip were obtained. First, the radial, ulnar and axillary arteries were dissected and isolated. The radial and ulnar arteries were transected. 100cc normal saline was injected through the axillary artery, sequentially clamping the radial followed by the ulnar artery so that adequate flow could be seen through all vessels. 100cc mixture of Biodür and hardener (10:1) was mixed and injected into the axillary artery. We first allowed free flow through both the ulnar and radial vessels followed by clamping of these vessels. This allowed the pressure to build up and fill the smaller vessels in the arms. After injection, the axillary artery was then clamped and the specimens were left to harden for 24-48 h. After hardening, dissection was performed by making a curvilinear incision centred over the lateral epicondyle. The anconeus was identified and the interval between the anconeus and ECU was then confirmed. Measurements of the anconeus muscle were taken. Blunt dissection was carried between anconeus and ECU until the RPIA was identified and protected. We isolated the MCA by dissecting proximally. This was found to run with the nerve to the anconeus. Once this vessel had been protected, the muscle reflected from distal to proximal staying along its ulnar border. The branches of the RPIA were ligated and the dissection was continued proximally. Measurements of the distances of the RPIA, MCA were taken. Results: The average distance of olecranon to muscle tip was 95.0mm. The average distance of lateral epicondyle (LE) to muscle tip was 90.8mm. The average distance of LE to olecranon was 49.8mm. The average location of the RPIA was 63.mm when measuring LE to vessel, 68.3mm when measuring olecranon to vessel, 18.3mm when measuring RPIA to muscle tip. The average RPIA diameter was 1.1mm and length was 36.4mm from the initial branching of the posterior interosseous artery. The average MCA diameter was 0.7mm. The posterior branch of the radial collateral artery was only found in 3/8 specimens. The RPIA and MCA were constant in all specimens. Dissection was safely carried to the border of the LE and olecranon without disruption of the MCA. CONCLUSIONS: Our conclusions determined that if dissection of the anconeus is undertaken, the RPIA remains constant between the interval of the ECU as well as anconeus at an average distance of 18.3mm from the tip of the muscle measuring proximally; moreover, the MCA was constant in all specimens found directly between the LE and olecranon always running with the nerve to the anconeus. When dissecting and mobilizing to ensure preservation of the MCA, dissection should be taken from distal to proximal as well as dissecting along the ulnar border of the anconeus. Proximal dissection can be taken as proximal as the border of the LE and olecranon as that did not disrupt MCA blood supply.

Repaired distal biceps magnetic resonance imaging anatomy compared with outcome.

BACKGROUND: This study examined the magnetic resonance imaging (MRI) appearance of an anterior incision distal biceps tendon repair and evaluated the association between appearance and outcome. MATERIALS AND METHODS: Nineteen patients were randomly recruited to undergo an elbow MRI from a single-surgeon series of distal biceps repairs using an anterior approach. Tendon healing was evaluated by the integrity of the repair, the amount of heterogeneity within the tendon substance, and the presence of heterotopic bone. The angle of tendon insertion on the tuberosity was used to quantify the tendon location from the MRI in the patients and in 10 healthy volunteers. All patients completed the Disabilities of Arm, Shoulder and Hand (DASH) and a visual analog pain scale (VAPS), and 17 patients underwent isometric supination strength testing. MRI findings were statistically compared with the outcome scores. RESULTS: All of the repairs healed to cortical bone. High intrasubstance heterogeneity or heterotopic bone was present in 11 patients (58%). The insertion site angle of the repaired tendons was 73° more anterior than the uninjured controls (P < .001). Average DASH was 7.7 (range, 0-49.2) and VAPS was 0.7 (range, 0-5). At 60° of forearm supination, supination strength was 67% of the uninjured side (P < .01). No significant differences in DASH or VAPS scores were found between groups based on tendon appearance. CONCLUSIONS: The distal biceps tendon predictably heals to cortical bone but demonstrates a wide variability in overall morphology that does not influence DASH or VAPS scores. A significant decrease in strength at 60° of supination appears to be an effect of an anterior tendon reattachment location.

Anatomic and biomechanical analysis of the short and long head components of the distal biceps tendon.

HYPOTHESIS: The short head bundle of the distal biceps tendon is more efficient at elbow flexion, and the long head is more efficient at forearm supination. METHODS: The short and long head bundles of the distal biceps tendon were separated to the bicipital tuberosity in 6 cadavers. The area and centroid of each bundle insertion were computed from surface points measured within each footprint. Each bundle was individually loaded. The supination torque and flexion load generated were recorded at 90° of elbow flexion. The slope of the torque generated versus biceps load was used to define the supination moment arm. The ratio of the flexion load generated to biceps load applied was used to define the relative flexion efficiency. RESULTS: The short head insertion was positioned distal and anterior relative to the long head and typically included the apex of the tuberosity. The areas of the long and short heads were 59 ± 15 and 94 ± 44 mm(2) (P = .07), respectively. The long head moment arm was significantly higher in supination. The short head had a significantly higher moment arm in neutral and pronation. The ratio of the flexion load to biceps load was 15% higher for the short head. CONCLUSION: The short and long heads of the biceps have distinct insertions. The short head's insertion allows it to be relatively more efficient at elbow flexion at 90°. In the neutral and pronated forearm, the short head is the relatively more efficient supinator. In the supinated forearm, the long head becomes relatively more efficient at supination.

Median and Digital Nerve In Situ Tension in the Hand.

Background: Digital nerves will experience tension under normal daily activities, and understanding the amount of tension experienced in these nerves relates directly to the necessary strength in nerve repairs. To begin quantification of tension, the tension borne by the median and digital nerves in cadaveric hands was quantified under conditions of finger hyperextension, nerve distraction, and finger flexion. Methods: Five cadaveric hands were mounted in a special fixture that allowed finger hyperextension and flexion and could apply known distractions while the tension borne by each digital nerve was measured. Sequential dissection exposed the digital nerves so that measurements of tension in the median, common, and proper digital nerves were conducted with finger hyperextension, nerve distraction, and finger flexion. Results: Metacarpophalangeal (MCP) hyperextension of 30° created mean nerve tensions up to 0.64 N, 5 mm of nerve distraction created mean nerve tensions up to 1.23 N, and 90° of MCP flexion relieved up to a mean of 1.18 N of nerve tension. Conclusions: In situ tension is present in the median and digital nerves with digital motion. Finger hyperextension and nerve distraction produce tension, whereas finger flexion reduces tension. Existing nerve repairs are strong enough to withstand in situ nerve tensions produced by reasonable digital motion if the original nerve length is present.

Conduit/Wrap Repairs to Digital Nerves Provide Residual Strength After Peak Loading.

BACKGROUND: Many techniques are used for digital nerve repair, most commonly coaptation by sutures. Nerve repairs must be strong while offering an environment for nerve regeneration. Sutures can damage the nerve and thereby limit growth and regeneration. Sutures can rip and cause sudden catastrophic failure. Fibrin glue and conduit-wraps allow a good environment for growth, but neither provides much strength. A benefit to conduit repair would arise if the repair maintained integrity after the peak load so that the path for regrowth stayed in place. The goal for this study was to determine whether conduit with glue provides continued strength after a maximum load is reached. METHODS: Digital cadaveric nerves were harvested and repaired with 2 epineurial sutures, conduit, and fibrin glue in all combinations. Tests to failure were performed, gap displacement between nerve ends recorded, and the postpeak load energy to dissociation of the nerve and conduit was calculated. RESULTS: Conduit with glue and 2 sutures at the end had the greatest energy and displacement after the peak load but was not significantly different than conduit with glue and 1 suture. Conduit with glue alone obtained statistically the same displacement as conduit with glue and 2 sutures. Conduit, with or without glue, and 2 sutures was statistically the same as suture only repair for peak load. CONCLUSION: Conduit/wrap maintains a load capacity and a path for nerve regeneration after the peak. Suture at the ends of conduit, not at the coaptation site, reduces damage at the point of injury.

Valgus fatigue and nonlinear damage accretion of the anterior bundle of the elbow medial collateral ligament (AMCL).

Failure by fatigue is one mechanism by which ligaments can rupture, with the accumulation of damage gradually degrading the ligament strength. Baseball pitchers who perform repeated high-level throwing continuously subject the medial ligament complex of the elbow to extreme levels of loading, which can lead to fatigue and eventual rupture. This study sought to investigate this behavior and quantify the fatigue properties of the anterior bundle of the medial collateral ligament (AMCL) with respect to valgus elbow torque. Eleven pairs of cadaveric elbow specimens were used for this study. One side of each pair was tested in vertical elongation at four flexion angles and then tested to failure at 90° of flexion. The contralateral specimens were tested in valgus fatigue at 90° of flexion using a specialized apparatus with application of known moments based on the elongation failure load. The average tensile failure load for the AMCL was 595.3 ± 201.9 N. During cycling, the average increase in the maximum valgus rotation angle was 4.77° ± 2.82°. The average maximum stretch of the AMCL middle band increased from 1.066 ± 0.017 to 1.076 ± 0.018 near the time of fatigue failure. The average cycles to failure for specimens tested at 90% and 80% of the estimated failure torque were 3211 ± 4721.33 and 25063 ± 30487.58, respectively. The nonlinear non-dimensional fatigue life and damage accretion results work in conjunction to predict the fatigue properties for a valgus elbow motion of arbitrary torque magnitude at 90° of elbow flexion.

The Association of Crista Volume With Sesamoid Position as Measured From 3D Reconstructions of Weightbearing CT Scans.

BACKGROUND: Malposition of the sesamoids relative to the first metatarsal head may relate to intersesamoid crista underdevelopment or erosion. Using 3-dimensional models created from weightbearing CT (WBCT) scans, the current work examined crista volume and its relationship to first metatarsal pronation and sesamoid station. METHODS: Thirty-eight hallux valgus (HV) patients and 10 normal subjects underwent weightbearing or simulated WBCT imaging. The crista was outlined by the inferior articular surface, and a line was drawn to connect the lowest point of each sulcus on either side of the intersesamoidal crista throughout the length of the crista. The volume was calculated. Sesamoid station and first metatarsal pronation were calculated from the 3D reconstructions. The mean crista volumes between HV and normal patients were statistically compared, as were the crista volume and pronation angle between sesamoid stations. RESULTS: The mean crista volume in HV patients was 80.10 ± 35 mm3 and in normal subjects was 150.64 ± 24 mm3, which differed significantly between the 2 groups (P < .001). Mean crista volumes were found to be statistically significantly different between the sesamoid stations (P < .001) with decreasing crista volumes significantly and strongly correlated with increasing sesamoid station (r = -0.80, P < .001). There was no difference in the mean pronation angle between the 4 sesamoid stations (P = .37). The pronation angle was not associated with crista volume (P = .52). CONCLUSION: HV patients have lower mean crista volume than normal patients. Crista volume is correlated with sesamoid station. Pronation of the first metatarsal was not associated with crista volume. CLINICAL RELEVANCE: Crista volume may offer an additional determinant for the severity of hallux valgus.

Biomechanical analysis of stability of joint depression calcaneal fractures: Fixation with locking compression plate alone compared with addition of supplemental oblique screw.

Purpose: The standard treatment of calcaneus fractures is a lateral plate and screw construct. Patients at our institution have been treated with a lateral locking plate combined with one retrograde screw inserted in the oblique plane to allow immediate weight bearing. The purpose of this study was to determine whether addition of a oblique screw to a lateral plate construct increases stability. Methods: A Sanders 2B fracture (AO/OTA 83-C2) was created in 8 pairs (16 total specimens) of cadaveric feet. All were repaired using a lateral locking plate/screws construct. One specimen in each pair was chosen randomly to receive an additional oblique screw. The specimens were tested with cyclic load of up to 800 N. Movement at the fracture sites and subsidence of the talus were tracked with a three-dimensional video analysis system. Results: Talar subsidence was not significantly affected by the presence of the additional oblique screw (p = 0.22). The sustentaculum fragment in the case of the screw repair moved 0.39 mm while the same fragment without the additional screw repair displaced 0.12 mm (p < 0.01). Two repairs with and one repair without the additional screw failed during longer-term cyclic loading. Conclusion: The two repair types were not statistically different in regards to talar subsidence. While statistical significance resulted in the comparison of sustentaculum fragment movement, the amount of movement did not reach a level of clinical relevance. This study demonstrated immediate stability and durability of the additional screw construct with high volume weight bearing loads.

A biomechanical comparison of superior ramus plating versus intramedullary screw fixation for unstable lateral compression pelvic ring injuries,,.

INTRODUCTION: Management of the anterior component of unstable lateral compression (LC) pelvic ring injuries remains controversial. Common internal fixation options include plating and superior pubic ramus screws. These constructs have been evaluated in anterior-posterior compression (APC) fracture patterns, but no study has compared the two for unstable LC patterns, which is the purpose of this study. METHODS: A rotationally unstable LC pelvic ring injury was modeled in 10 fresh frozen cadaver specimens by creating a complete sacral fracture, disruption of posterior ligaments, and ipsilateral superior and inferior rami osteotomies. All specimens were repaired posteriorly with two fully threaded 7 mm cannulated transiliac-transsacral screws through the S1 and S2 corridors. The superior ramus was repaired with either a 3.5 mm pelvic reconstruction plate (n = 5) or a bicortical 5.5 mm cannulated retrograde superior ramus screw (n = 5). Specimens were loaded axially in single leg support for 1000 cycles at 400 N followed by an additional 3 cycles at 800 N. Displacement and angulation of the superior and inferior rami osteotomies were measured with a three-dimensional (3D) motion tracker. The two fixation methods were then compared with Mann-Whitney U-Tests. RESULTS: Retrograde superior ramus screw fixation had lower average displacement and angulation than plate fixation in all categories, with the motion at the inferior ramus at 800 N of loading showing a statistically significant difference in angulation. CONCLUSION: Although management of the anterior ring in unstable LC injuries remains controversial, indications for fixation are becoming more defined over time. In this study, the 5.5 mm cannulated retrograde superior ramus screw significantly outperformed the 3.5 mm reconstruction plate in angulation of the inferior ramus fracture at 800 N. No other significance was found, however the ramus screw demonstrated lower average displacements and angulations in all categories for both the inferior and superior ramus fractures.

The Rotator Cable Does Not Stress Shield the Crescent Area During Shoulder Abduction.

BACKGROUND: It is accepted by the orthopaedic community that the rotator cable (RCa) acts as a suspension bridge that stress shields the crescent area (CA). The goal of this study was to determine if the RCa does stress shield the CA during shoulder abduction. METHODS: The principal strain magnitude and direction in the RCa and CA and shoulder abduction force were measured in 20 cadaveric specimens. Ten specimens underwent a release of the anterior cable insertion followed by a posterior release. In the other 10, a release of the posterior cable insertion was followed by an anterior release. Testing was performed for the native, single-release, and full-release conditions. The thicknesses of the RCa and CA were measured. RESULTS: Neither the principal strain magnitude nor the strain direction in either the RCa or the CA changed with single or full RCa release (p ≥ 0.493). There were no changes in abduction force after single or full RCa release (p ≥ 0.180). The RCa and CA thicknesses did not differ from one another at any location (p ≥ 0.195). CONCLUSIONS: The RCa does not act as a suspension bridge and does not stress shield the CA. The CA primarily transfers shoulder abduction force to the greater tuberosity. CLINICAL RELEVANCE: The CA is important in force transmission during shoulder abduction, and efforts should be made to restore its continuity with a repair or reconstruction.