Numerical and Experimental Analyses of Developed Friction Stir Spot Welding (DFSSW) Based on Systematic Design Process Approach.

This research paper presents a developed technique for Friction Stir Spot Welding (FSSW) to join similar aluminum sheets (6061), and then this technique was analyzed critically based on numerical simulation and experimental work. The objective of this Developed Friction Stir Spot Welding (DFSSW) is to avoid or at least reduce the keyhole defects by optimizing the design parameters of the process. The coupling problem (thermomechanical) was solved numerically using the finite element method to find the variations of temperatures and stress distributions in addition to the applied forces by the tool. Different parameters were considered in the numerical analysis, such as rotational speed and plunge depth. The experimental results proved the success of the developed technique by comparing the available results of tensile shear force with the results of other researchers that applied the traditional FSSW. It was obtained the highest tensile shear force (2388 N) under the optimal working and design conditions, when the rotational speed, plunging depth, height, and diameter of the sliced disc were 2100 rpm, 0.3 mm, 3.5 mm, and 12 mm, respectively. It was found that both the diameter and height of the sliced disc are significant parameters that ensure the success of this new technique when selecting the suitable values for these parameters. Otherwise, selecting unsuitable values of these parameters leads to appearing defects (e.g., flash) or the sample will fail under a low level of tensile shear force. The other essential advantage outcome point of this new technique was reducing the defect of the keyhole significantly compared with the results of typical Friction Stir Spot Welding. According to the results of the promising developed welding procedure that can be automated, it can be used widely in the industrial sectors.

Hyperelastic Properties of Bamboo Cellulosic Fibre-Reinforced Silicone Rubber Biocomposites via Compression Test.

Materials that exhibit highly nonlinear behaviour are intricate to study. This is due to their physical properties, as they possess a very large deformation. Silicone rubber is among the materials that can be classified as possessing such characteristics, despite their being soft and frequently applied in medical applications. Due to their low mechanical properties, however, it is believed that a filler addition could enhance them. This study, therefore, aims to investigate the effect of the addition of bamboo cellulosic filler to silicone rubber in terms of its compressive properties in order to quantify its material constants using the hyperelastic theory, specifically the Neo-Hookean and Mooney-Rivlin models. The specimens' compressive properties were also compared between specimens immersed in seawater and those not immersed in seawater. The findings showed that the compressive properties, stiffness, and compressive strength of the bamboo cellulosic fibre reinforced the silicone rubber biocomposites, improved with higher bamboo filler addition. Specimens immersed in seawater showed that they can withstand a compressive load of up to 83.16 kPa in comparison to specimens not immersed in seawater (up to 79.8 kPa). Using the hyperelastic constitutive models, the Mooney-Rivlin model displayed the most accurate performance curve fit with the experimental compression data with an R2 of up to 0.9999. The material constant values also revealed that the specimens immersed in seawater improved in stiffness property, as the C1 material constant values are higher than for the specimens not immersed in seawater. From these findings, this study has shown that bamboo cellulosic filler added into silicone rubber enhances the material's compressive properties and that the rubber further improves with immersion in seawater. Thus, these findings contribute significantly towards knowledge of bamboo cellulosic fibre-reinforced silicone rubber biocomposite materials.

Primary percutaneous coronary intervention in nonagenarians: is it worthwhile?

BACKGROUND: Previous studies have demonstrated the feasibility of primary percutaneous coronary intervention (PPCI) in carefully selected nonagenarians. Although current guidelines recommend immediate revascularization in patients with ST elevation myocardial infarction (STEMI) it remains unclear whether PPCI reduces mortality in nonagenarians. The objective of this study is to compare mortality in nonagenarians presenting via the PPCI pathway who undergo coronary intervention, versus those who are managed medically. METHODS AND RESULTS: A total of 111 consecutive nonagenarians who presented to our tertiary center via the PPCI pathway between July 2013 and December 2018 with myocardial infarction were included. Clinical and angiographic details were collected alongside data on all-cause mortality. The final diagnosis was STEMI in 98 (88.3%) and NSTEMI in 13 (11.7%). PPCI was performed in 42 (37.8%), while 69 (62.2%) were medically managed. A significant number of the medically managed cohort had atrial fibrillation (23.2% vs 2.4% p = 0.003) and presented with a completed infarct (43.5% vs 4.8% p = 0.001). Other baseline and clinical variables were well matched in both groups. There was a trend towards increased 30-day mortality in the medically managed group (40.6% vs 23.8% p = 0.07). Kaplan Meier survival analysis demonstrated a significant difference in survival by 3 years (48.1% vs 21.7% p = 0.01). This was the case even when those with completed infarcts were excluded (44.3% vs 14.6%, p = 0.01). CONCLUSION: In this series of selected nonagenarians presenting with acute myocardial infarction, those undergoing PPCI appeared to have a lower mortality compared to those managed medically.

Soil compartment is a major determinant of the impact of simulated rainfall on desert microbiota.

Although desert soils support functionally important microbial communities that affect plant growth and influence many biogeochemical processes, the impact of future changes in precipitation patterns on the microbiota and their activities is largely unknown. We performed in-situ experiments to investigate the effect of simulated rainfall on bacterial communities associated with the widespread perennial shrub, Rhazya stricta in Arabian desert soils. The bacterial community composition was distinct between three different soil compartments: surface biological crust, root-attached, and the broader rhizosphere. Simulated rainfall had no significant effect on the overall bacterial community composition, but some population-level responses were observed, especially in soil crusts where Betaproteobacteria, Sphingobacteria, and Bacilli became more abundant. Bacterial biomass in the nutrient-rich crust increased three-fold one week after watering, whereas it did not change in the rhizosphere, despite its much higher water retention. These findings indicate that between rainfall events, desert-soil microbial communities enter into stasis, with limited species turnover, and reactivate rapidly and relatively uniformly when water becomes available. However, microbiota in the crust, which was relatively enriched in nutrients and organic matter, were primarily water-limited, compared with the rhizosphere microbiota that were co-limited by nutrients and water.

Semisolid metal processing techniques for nondendritic feedstock production.

Semisolid metal (SSM) processing or thixoforming is widely known as a technology that involves the formation of metal alloys between solidus and liquidus temperatures. For the procedure to operate successfully, the microstructure of the starting material must consist of solid near-globular grains surrounded by a liquid matrix and a wide solidus-to-liquidus transition area. Currently, this process is industrially successful, generating a variety of products with high quality parts in various industrial sectors. Throughout the years since its inception, a number of technologies to produce the appropriate globular microstructure have been developed and applied worldwide. The main aim of this paper is to classify the presently available SSM technologies and present a comprehensive review of the potential mechanisms that lead to microstructural alterations during the preparation of feedstock materials for SSM processing.

Microstructural evolution during DPRM process of semisolid ledeburitic D2 tool steel.

Semisolid metal processing is a relatively new technology that offers several advantages over liquid processing and solid processing because of the unique behaviour and characteristic microstructure of metals in this state. With the aim of finding a minimum process chain for the manufacture of high-quality production at minimal cost for forming, the microstructural evolution of the ledeburitic AISI D2 tool steel in the semisolid state was studied experimentally. The potential of the direct partial remelting (DPRM) process for the production of AISI D2 with a uniform globular microstructure was revealed. The liquid fraction was determined using differential scanning calorimetry. The microstructures of the samples were investigated using an optical microscope and a scanning electron microscope equipped with an energy dispersive spectroscopy analyser, while X-ray phase analysis was performed to identify the phase evolution and the type of carbides. Mechanical characterisation was completed by hardness measurements. The typical microstructure after DPRM consists of metastable austenite which was located particularly in the globular grains (average grain size about 50 µ m), while the remaining interspaces were filled by precipitated eutectic carbides on the grain boundaries and lamellar network.

Influence of PODE1 additive into ethanol-gasoline blends (E10) on fuel properties and phase stability.

Polyoxymethylene dimethyl ethers (PODEn, n = 1-8) as an oxygenated fuel are a promising alternative fuel with a high oxygen concentration, a low C:H ratio, and no C-C bonds in their chemical structure. This could lead to smoke-free combustion. In this study, we chose to focus on PODE1 because of its lower cetane number, which makes it more suitable for use in spark ignition (SI) engines. However, its lower boiling point and octane number remain challenges. A low boiling point may lead to high vapour pressure and require storage and handling comparable to gaseous fuels. We investigated the effect of adding PODE1 to gasoline-ethanol blends (E10) on fuel properties, including distillation curve, octane number, phase stability, C/O/H ratio, heat of combustion, kinematic viscosity, and density. Our results showed that the blended fuels of E10 and PODE1 are stable up to 10 % PODE1, and there was no phase separation. Additionally, up to 10 % PODE1 additive had no significant side effect on the fuel properties of E10, particularly boiling point and octane number. Thus, work offers creative points by proposing a new candidate for additive fuel to gasoline-ethanol blends, which contributes to reducing the soot emission of GDI engines.

Morphological, Physical, and Mechanical Properties of Sugar-Palm (Arenga pinnata (Wurmb) Merr.)-Reinforced Silicone Rubber Biocomposites.

The development of environmentally benign silicone composites from sugar palm fibre and silicone rubber was carried out in this study. The mechanical, physical, and morphological properties of the composites with sugar palm (SP) filler contents ranging from 0% to 16% by weight (wt%) were investigated. Based on the uniaxial tensile tests, it was found that the increment in filler content led to higher stiffness. Via dynamic mechanical analysis (DMA), the viscoelastic properties of the silicone biocomposite showed that the storage modulus and loss modulus increased with the increment in filler content. The physical properties also revealed that the density and moisture absorption rate increased as the filler content increased. Inversely, the swelling effect of the highest filler content (16 wt%) revealed that its swelling ratio possessed the lowest rate as compared to the lower filler addition and pure silicone rubber. The morphological analysis via scanning electron microscopy (SEM) showed that the sugar palm filler was evenly dispersed and no agglomeration could be seen. Thus, it can be concluded that the addition of sugar palm filler enhanced the stiffness property of silicone rubber. These new findings could contribute positively to the employment of natural fibres as reinforcements for greener biocomposite materials.

Mean platelet volume to platelet count ratio as a laboratory indicator of mortality in pneumonia following ischemic stroke.

BACKGROUND: Platelets have a vital role in antimicrobial host defenses. The objective of this study was to evaluate if increased mean platelet volume to platelet count (MPV/PC) ratio in acute ischemic stroke patients complicated with pneumonia was associated with increased mortality risk. METHODS: The current study was conducted at Zagazig University Hospitals. It included 500 acute ischemic stroke patients classified as group 1 that included 51 patients complicated with pneumonia after admission and group 2 that included the remaining 449 patients. Clinical assessment was carried out to exclude comorbid medical illnesses likely to interfere with platelet function or morphology. Laboratory investigations including MPV/PC ratio and brain imaging were carried out for all patients. RESULTS: There was a significant difference between both groups regarding age, National Institutes of Health Stroke Scale (NIHSS) score, and mortality within 30 days (p = 0.02, 0.03, 0.01). There was a significant difference between survivors and non-survivors of group 1 regarding to pneumonia severity index (PSI) classes IV and V (p = 0.01 and 0.02, respectively). Also, there was a significant difference regarding confusion, urea ≥ 7 mmol/L, respiratory rater ≥ 30 breaths/min, systolic blood pressure ≤ 90 mmHg or diastolic blood pressure ≤ 60 mmHg, and age ≥ 65 years at pneumonia occurrence (CURB-65) scores 3, 4, and 5 (p = 0.03, 0.02, and 0.01, respectively). Moreover, there was a significant difference regarding decreased GCS score at pneumonia occurrence, higher NIHSS scores, PSI, and higher MPV/PC ratio (p = 0.01, 0.01, 0.028, and 0.01, respectively). Age > 65 years, need for mechanical ventilation, GCS score of > 9, PSI class ≥ IV, CURB-65 scores ≥ 3, and increased MPV/PC ratio were all significantly associated with 30-day mortality in group 1 (p = 0.03, 0.01, 0.001, 0.04, 0.01, and 0.03, respectively). The predictors of 30-day mortality risk factors were GCS less than 9, increased MPV/PC ratio, and CURB-65 scores ≥ 3 (p = 0.001, 0.05, and 0.01, respectively). CONCLUSIONS: Once pneumonia develops, MPV/PC ratio could be considered a significant laboratory indicator of 30-day mortality.

3,5-Diiodotyrosine excretion in human urine in individuals of differing thyroidal status.

The urinary excretion of 3,5-diiodotyrosine was determined in euthyroid, hypothyroid and hyperthyroid individuals using a sensitive gas chromatographic mass spectrometric assay. This involved a multi-step extraction of the amino acid from urine (mean efficiency 28 +/- 5.7%) then conversion to the N,O-diheptafluorobutyryl methyl ester. The fragmentation of the derivative is discussed. Although the mean excretions in the two pathological states were significantly different from that of euthyroid individuals (P less than 0.01 in both instances) there was considerable overlap with the normal range.

Mass spectral properties of volatile derivatives of thyronine (T0) and use of these in the study of thyronine excretion in eu-, hyper- and hypothyroidism.

The mass spectral properties of four classes of derivatives of thyronine are discussed ( oxazolidinone , O-methyl oxazolidinone , O-acetyl oxazolidinone and N,O- diheptafluorobutyryl methyl ester). An assay for thyronine in human urine is described based on the N,O- diheptafluorobutyryl methyl ester. Results of T0 excretion in euthyroid humans were compared with those obtained previously using an assay based on the O-acetyl oxazolidinone derivative. Patients with frank hyperthyroidism had significantly higher T0 excretion than euthyroid subjects (2 alpha less than 0.002) and hypothyroid patients lower T0 excretions than euthyroid subjects (2 alpha less than 0.002). Some overlap between the two pathological ranges and the normal euthyroid range was evident.

Comparison of radioisotope methods for the measurement of phosphate absorption in normal subjects and in patients with chronic renal failure.

1. Intestinal phosphate absorption was measured in normal subjects, in patients with chronic renal failure, and in post-transplant patients, by a double isotope technique involving oral administration of 32P and simultaneous intravenous injection of 33P with subsequent deconvolution analysis. 2. By this technique intestinal phosphate absorption has been shown to have two components: an initial rapid phase, which is completed by 3 h, and a slower more prolonged phase, which continues beyond 7 1/2 h. 3. Phosphate malabsorption has been demonstrated in chronic renal failure and transplant patients, which is accounted for by impairment of the initial rapid phase of absorption. 4. Results obtained by deconvolution analysis have been compared with other estimates of phosphate absorption obtained from analysis of 32P radioactivity curves alone. 5. The fractional hourly rate of absorption and the plasma 32P radioactivity at 60 min corrected for extracellular fluid volume provided the best approximations to the result obtained by deconvolution analysis, with respect to both the maximal rate of phosphate absorption and cumulative percentage phosphate absorption.

3,5-Diiodotyrosine and thyronine in the urine of patients with chronic renal disease.

Urinary 3,5-diiodotyrosine (DIT) and thyronine (T0) excretion was investigated in 18 patients with chronic renal disease. In accord with previous findings serum T4 and thyroid hormone binding proteins measured in 17 patients were in the low or normal range. Urinary albumin excretion was elevated in all 18 and T4 binding prealbumin (TBPA) in 15 of the 18. Urinary T0 excretion measured in 12 patients was also significantly lower than normal (mean +/- SD 4.4 +/- 2.6 vs 15.8 +/- 5.8 nmol/24 h renal vs normal 2 P less than 0.001). In contrast urinary DIT excretion was significantly elevated in renal patients compared with normal subjects (2.0 +/- 1.5 vs 0.75 +/- 0.41 nmol/24 h, respectively). Possible sources of the increased DIT are discussed.