RESUMO
Cement mortar is used as a conglomerate in the majority of construction work. There are multiple variants of cement according to the type of aggregate used in its fabrication. One of the major problems that occurs while working with this type of material is the excessive loss of moisture during cement hydration (setting and hardening), known as shrinkage, which provokes a great number of construction pathologies that are difficult to repair. In this way, the design of a new sensor able to measure the moisture loss of mortars at different age levels is useful to establish long-term predictions concerning mortar mass volume loss. The purpose of this research is the design and fabrication of a new capacitive sensor able to measure the moisture of mortars and to relate it with the shrinkage.
RESUMO
In the last 30 years numerous attempts have been made to improve the efficiency of the parabolic collectors in the electric power production, although most of the studies have focused on the industrial production of thermoelectric power. This research focuses on the application of this concentrating solar thermal power in the unexplored field of building construction. To that end, a mechatronic prototype of a hybrid paraboloidal and cylindrical-parabolic tracker based on the Arduido technology has been designed. The prototype is able to measure meteorological data autonomously in order to quantify the energy potential of any location. In this way, it is possible to reliably model real commercial equipment behavior before its deployment in buildings and single family houses.
RESUMO
This document develops the study of an implementation project of a home automation system in a housing placed in the town of Galapagar, Madrid. This house, which is going to be occupied by a four-member family, consists of 67 constructed square meters distributed in lounge, kitchen, three bedrooms, bath, bathroom and terrace, this being a common arrangement in Spain. Thus, this study will allow extracting conclusions about the adequacy of the home automation in a wide percentage of housing in Spain. In this document, three house automation proposals are developed based on the requirements of the client and the different home automation levels that the Spanish House and Building Automation Association has established, besides two parallel proposals relating to the safety and the technical alarms. The mentioned proposed systems are described by means of product datasheets and descriptions, distribution plans, measurements, budgets and flow charts that describe the functioning of the system in every case. An evaluation of each system is included, based on other studies conclusions on this matter, where expected energy savings from each design, depending on the current cost of lighting, water and gas, as well as the expected economic amortization period is evaluated.
RESUMO
There are many historic buildings whose construction is based on timber frame walls. Most buildings built during the nineteenth and early twentieth centuries were based on timber frame walls with vertical support elements. These timber frame elements are affected by their moisture content and by the passage of time. If the interaction of the timber frame walls with hygrothermal fluctuations were known, the maintenance of these buildings could be improved significantly. To determine the moisture content of wood there are two types of meters on the market: on the one hand, capacitance meters which consist of two side ends and where the moisture content is measured locally between two peaks. On the other hand, there are meters based on the variation of electromagnetic transmittance of timber, which depends on the moisture of timber. The second ones are very expensive and difficult to handle. This work presents a new non-intrusive capacitive sensor that measures the global moisture content in a section of the timber frame walls and therefore its accuracy is similar to the accuracy that can be obtained with electromagnetic transmittance meters. Additionally, as it is a capacitive sensor, it is low cost and easy to operate.
RESUMO
This paper describes a new low-cost means to detect and locate mechanical impacts (collisions) on a 3D metal-based structure. We employ the simple and reasonably hypothesis that the use of a homogeneous material will allow certain details of the impact to be automatically determined by measuring the time delays of acoustic wave propagation throughout the 3D structure. The location of strategic piezoelectric sensors on the structure and an electronic-computerized system has allowed us to determine the instant and position at which the impact is produced. The proposed automatic system allows us to fully integrate impact point detection and the task of inspecting the point or zone at which this impact occurs. What is more, the proposed method can be easily integrated into a robot-based inspection system capable of moving over 3D metallic structures, thus avoiding (or minimizing) the need for direct human intervention. Experimental results are provided to show the effectiveness of the proposed approach.
RESUMO
Currently there are many types of sensors that are used in lots of applications. Among these, magnetic sensors are a good alternative for the detection and measurement of different phenomena because they are a "simple" and readily available technology. For the construction of such devices there are many magnetic materials available, although amorphous ferromagnetic materials are the most suitable. The existence in the market of these materials allows the production of different kinds of sensors, without requiring expensive manufacture investments for the magnetic cores. Furthermore, these are not fragile materials that require special care, favouring the construction of solid and reliable devices. Another important feature is that these sensors can be developed without electric contact between the measuring device and the sensor, making them especially fit for use in harsh environments. In this review we will look at the main types of developed magnetic sensors. This work presents the state of the art of magnetic sensors based on amorphous ferromagnetic materials used in modern technology: security devices, weapon detection, magnetic maps, car industry, credit cards, etc.
RESUMO
Currently, there is a narrow range of materials that are used as attenuators of impact noise and building vibrations. Materials used in construction, such as elastic materials, must meet the requirement of having very low elastic modulus values. For the determination of the material's elastic modulus and the acoustic insulation of the same, costly and difficult to execute testing is required. The present paper exposes an alternative system that is simpler and more economic, consisting of a predefined striking device and a sensor able to determine, once the strike is produced, the energy absorbed by the plate. After the impact is produced, the plate undergoes a deformation, which absorbs part of the energy, the remaining part being transmitted to the slab and, at the same time, causing induced airborne noise in the adjoining room. The plate absorbs the power through its own deformation, which is measured with the help of a capacitive sensor. This way, it would be possible to properly define the geometry of the plates, after the execution of the test, and we will try to establish a relationship between the values proposed in this research and the acoustic behavior demanded by the Spanish standards.
RESUMO
This paper shows a new displacement-to-frequency transducer based on the variation of a coil inductance when a magnetic core is partially or completely inserted inside. This transducer is based on a Colpitts oscillator due its low manufacturing price, behavior and immunity to noise. A tank circuit with a configuration in parallel was used because it can be employed at lower frequencies and it enables it to make a direct analysis. The sensor has a dynamic range equal to the length of the coil. The cores can exchange sensors (coils with its ferromagnetic core) using the same electronic measuring system. In this way, with only an electronic circuit, the core sensor determines the measurement range. The obtained resolution is higher than 1/100,000, and the sensor also allows the measurement and knowing in real time the effect of vibration, thermal expansion, referred overload movements, etc.., that can occur in the structural elements of a building.
RESUMO
Many analyses of acoustic signals processing have been proposed for different applications over the last few years. When considering a bar-based structure, if the material through which the sound waves propagate is considered to be acoustically homogeneous and the sound speed is well known, then it is possible to determine the position and time of impact by a simple observation of the arrival times of the signals of all the transducers that are strategically disposed on the structure. This paper presents a generalized method for impact detection and location on a flat plate, together with a calibration procedure with which to obtain the sound speed from only one set of measurements. This propagation speed is not well known as a result of either imprecise material properties or the overlapping of longitudinal and transversal waves with different propagation velocities. The use of only three piezoelectric sensors allows the position and time of impact on the flat plate to be obtained when the sound speed is well known, while the use of additional sensors permits a larger detection area to be covered, helps to estimate the sound speed and/or avoids the wrong timing of difference measurements. Experimental results are presented using a robot with a specially designed knocking tool that produces impacts on a metallic flat plate.
RESUMO
Plaster is a construction material widely used for the production of prefabricated parts in building construction due to its high capacity for hygrothermal regulation, its good mechanical performance, and its fireproof nature, among other factors. Its historical use has been linked to ornamental elements, although more recent research is oriented towards the industrialisation of plaster composites and the design of prefabricated parts for false ceilings and interior partitions. In this work, the behaviour against water of four new plaster-based composite materials is studied, using additions of two types of super absorbent polymers (sodium polyacrylate and potassium polyacrylate) and a lightening material (vermiculite) in their manufacturing process. In addition, the transmission of water vapour through the samples was studied together with the water absorption capacity of the samples in order to check the suitability of the use of plaster-based materials exposed to these environments. The results of this study show that composites with the addition of super absorbent polymers as well as vermiculite significantly improve their water performance compared to traditional materials up to 7.3% water absorption with a minimal (13%) reduction in mechanical strength compared to current materials with similar additions. In this sense, a plaster material is obtained with wide possibilities of application in the construction sector that favours the development of sustainable and quality buildings, in line with Goal 9 for Sustainable Development included in the 2030 Agenda.
RESUMO
The building sector is currently undergoing a process of change due to concerns about the sustainability of the construction industry. The application of circular economy criteria to develop new, more sustainable construction products has become one of the major challenges for the society of the future. This research advances towards the development of new lightened gypsum composites that incorporate waste from end-of-life tyres and recycled fibres from mineral wool thermal insulation in their composition. The results show how it is possible to reduce the consumption of the original raw materials by replacing them with recycled rubber granular particles, developing new construction products that are lighter, with better water resistance and greater thermal resistance. Additionally, it is shown that the incorporation of recycled fibres from rock wool and glass wool insulation is a good solution to improve the mechanical resistance of lightened gypsum composites, giving these construction and demolition wastes a second useful life by reincorporating them in the process of manufacturing new prefabricated housing products.
RESUMO
This paper shows the characterization of a new lightened gypsum-based material for use in buildings. A plaster material has been designed with a polymeric compound based on polyvinyl acetate, bicarbonate and a boric acid solution, which reduce the density and thermal conductivity by up to 20% and 30%, respectively. In addition, tests have been carried out with the lightened plaster material reinforced with glass (GF), basalt (BF), polypropylene (PPF) and wood (WF) fibers. A significant improvement in mechanical properties was achieved. All samples obtained resistance values greater than 2 MPa in flexion and 3 MPa in compression. Physico-chemical analysis were also carried out. The study is completed with a statistical analysis, where confidence intervals have been obtained for the mean at 95% confidence for each of the physical properties studied.
RESUMO
Chronic diseases in childhood can affect the physical and mental health of patients and their families. The objective of this study was to identify the sociodemographic and psychosocial factors that predict resilience in family caregivers of children with cancer and to define whether there are differences in the levels of resilience derived from these sociodemographic variables. Three hundred and thirty family caregivers of children with cancer, with an average age of 32.6 years were interviewed. The caregivers responded to a battery of tests that included a questionnaire of sociodemographic variables, the Measuring Scale of Resilience, the Beck Depression Inventory, the Inventory of Quality of Life, the Beck Anxiety Inventory, an interview of caregiver burden and the World Health Organization Well-Being Index. The main findings indicate that family caregivers of children with cancer reported high levels of resilience, which were associated positively with quality of life, psychological well-being and years of study and associated negatively with depression, anxiety and caregiver burden. The variables that predicted resilience in families of children with cancer were quality of life, psychological well-being, depression and number of children. Family caregivers who were married and Catholic showed higher resilience scores. We conclude that being a caregiver in a family with children with cancer is associated with symptoms of anxiety and with depressive episodes. These issues can be overcome through family strength, well-being, quality of life and positive adaptation processes and mobilization of family resources.
Assuntos
Adaptação Psicológica , Cuidadores/psicologia , Depressão/epidemiologia , Neoplasias/epidemiologia , Qualidade de Vida , Resiliência Psicológica , Adulto , Ansiedade/epidemiologia , Criança , Estudos Transversais , Depressão/psicologia , Família , Feminino , Humanos , Masculino , Neoplasias/psicologiaRESUMO
Non-destructive testing can be used to determine some of the most relevant physical properties of building materials. In this work, two low-cost measuring devices were developed capable of determining the variation in real-time of the percentage of humidity that is produced in the construction of gypsum and plaster during the hardening process. For this, an Arduino resistive sensor and a capacitive sensor of our design were used. The results show how it is possible to determine the variations in mixing water content during the seven days of curing established by the UNE-EN 13279-2 standard as well relate to the mechanical resistance of the test specimens with the same percentage of humidity. Additionally, the study was completed with the determination of the formation of the dihydrate compound linked to this setting process in the test specimens by conducting X-ray diffraction and thermogravimetric analysis tests at different ages of the samples.