Tunable terahertz absorption of ion gel-graphene hybrids based on the Salisbury effect.

The gate-tunable absorption properties of graphene make it suitable for terahertz (THz) absorbers. However, the realization of a graphene-based THz absorber faces challenges between the difficulty of patterning graphene for processing and the intrinsically low absorbance of graphene with the high electric field needed to change the conductivity of graphene. This report presents an electrically tunable graphene THz absorber where a single-layer graphene film and a gold reflective layer are separated by a polyimide (PI) dielectric layer to form an easily fabricated three-layer Salisbury screen structure. The carrier density of the graphene layer can be efficiently tuned by a small external electrical gating (-5V-5 V) with the assistance of an ion gel layer. The voltage modulation of the Fermi energy level (EF) of graphene was confirmed by Raman spectra, and the variation of the device absorbance was confirmed using a THz time-domain spectroscopy system (THz-TDS). The measurements show that the EF is adjusted in the range of 0-0.5 eV, and THz absorbance is adjusted in the range of 60%-99%. The absorber performs well under different curvatures, and the peak absorbance is all over 95%. We conducted further analysis of the absorber absorbance by varying the thickness of the PI dielectric layer, aiming to examine the correlation between the resonant frequency of the absorber and the dielectric layer thickness. Our research findings indicate that the proposed absorber holds significant potential for application in diverse fields such as communication, medicine, and sensing.

Multilayer graphene-enabled structure based on Salisbury shielding effect for high-performance terahertz absorption.

Sandwich-type structure based on Salisbury screen effect is a simple and effective strategy to acquire high-performance terahertz (THz) absorption. The number of sandwich layer is the key factor that affects the absorption bandwidth and intensity of THz wave. Traditional metal/insulant/metal (M/I/M) absorber is difficult to construct multilayer structure because of low light transmittance of the surface metal film. Graphene exhibits huge advantages including broadband light absorption, low sheet resistance and high optical transparency, which are useful for high-quality THz absorber. In this work, we proposed a series of multilayer metal/PI/graphene (M/PI/G) absorber based on graphene Salisbury shielding. Numerical simulation and experimental demonstration were provided to explain the mechanism of graphene as resistive film for strong electric field. And it is important to improve the overall absorption performance of the absorber. In addition, the number of resonance peaks is found to increase by increasing the thickness of the dielectric layer in this experiment. The absorption broadband of our device is around 160%, greater than those previously reported THz absorber. Finally, this experiment successfully prepared the absorber on a polyethylene terephthalate (PET) substrate. The absorber has high practical feasibility and can be easily integrated with the semiconductor technology to make high efficient THz-oriented devices.

Modulation of graphene THz absorption based on HAuCl4 doping method.

Graphene is an attractive material for terahertz (THz) absorbers because of its tunable Fermi-Level (EF). It has become a research hotspot to modulate the EF of graphene and THz absorption of graphene. Here, a sandwich-structured single layer graphene (SLG)/ Polyimide (PI)/Au THz absorber was proposed, and top-layer graphene was doped by HAuCl4 solutions. The EF of graphene was shifted by HAuCl4 doping, which was characterized by scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and Raman tests. The results showed that the EF is shifted about 0.42 eV under 100 mM HAuCl4 doping, the sheet resistance is reduced from 1065 Ω/sq (undoped) to 375 Ω/sq (100 mM). The corresponding absorbance was increased from 40% to 80% at 0.65 THz and increased from 50% to 90% at 2.0 THz under 100 mM HAuCl4 doping. Detailed studies showed that the absorption came from a sandwich structure that meets the impedance matching requirements and provided a thin resonant cavity to capture the incident THz waves. In addition, not only the absorber can be prepared simply, but its results in experiments and simulations agree as well. The proposed device can be applied to electromagnetic shielding and imaging, and the proposed method can be applied to prepare other graphene-based devices.

A high-resolution flexible sensor array based on PZT nanofibers.

Flexible tactile sensor array has drawn great attention due to its ability to mimic human skin for sensing weak pressure and distinguishing pressure distribution, but the deficiency of sensitivity, the low resolution, and the complex and costly fabrication process seriously limit its development. Hence, it is urgent to explore a fully flexible sensor array with high sensitivity and high resolution as an electronic-skin. Here, the flexible piezoelectric tactile sensor array based on the composite film of PZT nanowires and polydimethylsiloxane (PDMS) was fabricated by the simple fabrication process (electrospinning process and mixture process). The electrospun PZT nanofibers have high aspect ratio and could enhance the generation and accumulation of the piezoelectric charges in the two electrodes of the composite film. By virtue of the inherently high piezoelectric coefficient of PZT material and high aspect ratio of PZT nanofibers, the composite film (75 wt% PZT nanofibers) presents high force-electric conversion capability and high sensitivity. Owing to the bottom electrode sheet shared by all sensor units and the supporting layer with relatively high elastic modulus, the sensor array shows high resolution to qualitatively sense the distribution and size of the impact in real time. Moreover, the sensor array also shows great durability, repeatability, and large working range. Based on these excellent characteristics, the sensor array has wide potential applications in the field of bionics science, robotics science and human-machine interaction.

Thickness Dependence of Ferroelectric and Optical Properties in Pb(Zr0.53Ti0.47)O3 Thin Films.

As a promising functional material, ferroelectric Pb(ZrxTi1-x)O3 (PZT) are widely used in many optical and electronic devices. Remarkably, as the film thickness decreases, the materials' properties deviate gradually from those of solid materials. In this work, multilayered PZT thin films with different thicknesses are fabricated by Sol-Gel technique. The thickness effect on its microstructure, ferroelectric, and optical properties has been studied. It is found that the surface quality and the crystalline structure vary with the film thickness. Moreover, the increasing film thickness results in a significant increase in remnant polarization, due to the interfacial layer effect. Meanwhile, the dielectric loss and tunability are strongly dependent on thickness. In terms of optical properties, the refractive index of PZT films increase with the increasing thickness, and the photorefractive effect are also influenced by the thickness, which could all be related to the film density and photovoltaic effect. Besides, the band gap decreases as the film thickness increases. This work is significant for the application of PZT thin film in optical and optoelectronic devices.

Motor Behavior Regulation of Rat Robots Using Integrated Electrodes Stimulated by Micro-Nervous System.

As a cutting-edge technology, animal robots based on living organisms are being extensively studied, with potential for diverse applications in the fields of neuroscience, national security, and civil rescue. However, it remains a significant challenge to reliably control the animal robots with the objective of protecting their long-term survival, and this has seriously hindered their practical implementation. To address this issue, this work explored the use of a bio-friendly neurostimulation system that includes integrated stimulation electrodes together with a remote wireless stimulation circuit to control the moving behavior of rat robots. The integrated electrodes were implanted simultaneously in four stimulation sites, including the medial forebrain bundle (MFB) and primary somatosensory cortex, barrel field (S1BF). The control system was able to provide flexibility in adjusting the following four stimulation parameters: waveform, amplitude, frequency, and duration time. The optimized parameters facilitated the successful control of the rat's locomotion, including forward movement and left and right turns. After training for a few cycles, the rat robots could be guided along a designated route to complete the given mission in a maze. Moreover, it was found that the rat robots could survive for more than 20 days with the control system implanted. These findings will ensure the sustained and reliable operation of the rat robots, laying a robust foundation for advances in animal robot regulation technology.

An optimized EEGNet decoder for decoding motor image of four class fingers flexion.

As a cutting-edge technology of connecting biological brain and external devices, brain-computer interface (BCI) exhibits promising applications on extensive fields such as medical and military. As for the disable individuals with four limbs losing the motor functions, it is a potential treatment way to drive mechanical equipments by the means of non-invasive BCI, which is badly depended on the accuracy of the decoded electroencephalogram (EEG) singles. In this study, an explanatory convolutional neural network namely EEGNet based on SimAM attention module was proposed to enhance the accuracy of decoding the EEG singles of index and thumb fingers for both left and right hand using sensory motor rhythm (SMR). An average classification accuracy of 72.91% the data of eight healthy subjects was obtained, which were captured from the one second before finger movement to two seconds after action. Furthermore, the character of event-related desynchronization (ERD) and event related synchronization (ERS) of index and thumb fingers was also studied in this study. These findings have significant importance for controlling external devices or other rehabilitation equipment using BCI in a fine way.

Flexible wide-range multidimensional force sensors inspired by bones embedded in muscle.

Flexible sensors have been widely studied for use in motion monitoring, human‒machine interactions (HMIs), personalized medicine, and soft intelligent robots. However, their practical application is limited by their low output performance, narrow measuring range, and unidirectional force detection. Here, to achieve flexibility and high performance simultaneously, we developed a flexible wide-range multidimensional force sensor (FWMFS) similar to bones embedded in muscle structures. The adjustable magnetic field endows the FWMFS with multidimensional perception for detecting forces in different directions. The multilayer stacked coils significantly improved the output from the µV to the mV level while ensuring FWMFS miniaturization. The optimized FWMFS exhibited a high voltage sensitivity of 0.227 mV/N (0.5-8.4 N) and 0.047 mV/N (8.4-60 N) in response to normal forces ranging from 0.5 N to 60 N and could detect lateral forces ranging from 0.2-1.1 N and voltage sensitivities of 1.039 mV/N (0.2-0.5 N) and 0.194 mV/N (0.5-1.1 N). In terms of normal force measurements, the FWMFS can monitor finger pressure and sliding trajectories in response to finger taps, as well as measure plantar pressure for assessing human movement. The plantar pressure signals of five human movements collected by the FWMFS were analyzed using the k-nearest neighbors classification algorithm, which achieved a recognition accuracy of 92%. Additionally, an artificial intelligence biometric authentication system is being developed that classifies and recognizes user passwords. Based on the lateral force measurement ability of the FWMFS, the direction of ball movement can be distinguished, and communication systems such as Morse Code can be expanded. This research has significant potential in intelligent sensing and personalized spatial recognition.

Hybrid Pressure Sensor Based on Carbon Nano-Onions and Hierarchical Microstructures with Synergistic Enhancement Mechanism for Multi-Parameter Sleep Monitoring.

With the existing pressure sensors, it is difficult to achieve the unification of wide pressure response range and high sensitivity. Furthermore, the preparation of pressure sensors with excellent performance for sleep health monitoring has become a research difficulty. In this paper, based on material and microstructure synergistic enhancement mechanism, a hybrid pressure sensor (HPS) integrating triboelectric pressure sensor (TPS) and piezoelectric pressure sensor (PPS) is proposed. For the TPS, a simple, low-cost, and structurally controllable microstructure preparation method is proposed in order to investigate the effect of carbon nano-onions (CNOs) and hierarchical composite microstructures on the electrical properties of CNOs@Ecoflex. The PPS is used to broaden the pressure response range and reduce the pressure detection limit of HPS. It has been experimentally demonstrated that the HPS has a high sensitivity of 2.46 V/104 Pa (50-600 kPa) and a wide response range of up to 1200 kPa. Moreover, the HPS has a low detection limit (10 kPa), a high stability (over 100,000 cycles), and a fast response time. The sleep monitoring system constructed based on HPS shows remarkable performance in breathing state recognition and sleeping posture supervisory control, which will exhibit enormous potential in areas such as sleep health monitoring and potential disease prediction.

Facilitated Photocatalytic Degradation of Rhodamine B over One-Step Synthesized Honeycomb-Like BiFeO3/g-C3N4 Catalyst.

In the present work, a facile one-step methodology was used to synthesize honeycomb-like BiFeO3/g-C3N4 composites, where the well-dispersed BiFeO3 strongly interacted with the hg-C3N4. The 10BiFeO3/hg-C3N4 could completely degrade RhB under visible light illumination within 60 min. The degradation rate constant was remarkably improved and approximately three times and seven times that of pristine hg-C3N4 and BiFeO3, respectively. This is ascribed to the following factors: (1) the unique honeycomb-like morphology facilitates the diffusion of the reactants and effectively improves the utilization of light energy by multiple reflections of light; (2) the charged dye molecules can be tightly bound to the spontaneous polarized BiFeO3 surface to form the Stern layer; (3) the Z-scheme heterojunction and the ferroelectric synergistically promoted the efficient separation and migration of the photogenerated charges. This method can synchronously tune the micro-nano structure, surface property, and internal field construction for g-C3N4-based photocatalysts, exhibiting outstanding potential in environmental purification.

Synergistic Enhancement Properties of a Flexible Integrated PAN/PVDF Piezoelectric Sensor for Human Posture Recognition.

The flexible pressure sensor has attracted much attention due to its wearable and conformal advantage. All the same, enhancing its electrical and structural properties is still a huge challenge. Herein, a flexible integrated pressure sensor (FIPS) composed of a solid silicone rubber matrix, composited with piezoelectric powers of polyacrylonitrile/Polyvinylidene fluoride (PAN/PVDF) and conductive silver-coated glass microspheres is first proposed. Specifically, the mass ratio of the PAN/PVDF and the rubber is up to 4:5 after mechanical mixing. The output voltage of the sensor with composite PAN/PVDF reaches 49 V, which is 2.57 and 3.06 times that with the single components, PAN and PVDF, respectively. In the range from 0 to 800 kPa, its linearity of voltage and current are all close to 0.986. Meanwhile, the sensor retains high voltage and current sensitivities of 42 mV/kPa and 0.174 nA/kPa, respectively. Furthermore, the minimum response time is 43 ms at a frequency range of 1-2.5 Hz in different postures, and the stability is verified over 10,000 cycles. In practical measurements, the designed FIPS showed excellent recognition abilities for various gaits and different bending degrees of fingers. This work provides a novel strategy to improve the flexible pressure sensor, and demonstrates an attractive potential in terms of human health and motion monitoring.

Reliable Fabrication of Graphene Nanostructure Based on e-Beam Irradiation of PMMA/Copper Composite Structure.

Graphene nanostructures are widely perceived as a promising material for fundamental components; their high-performance electronic properties offer the potential for the construction of graphene nanoelectronics. Numerous researchers have paid attention to the fabrication of graphene nanostructures, based on both top-down and bottom-up approaches. However, there are still some unavoidable challenges, such as smooth edges, uniform films without folds, and accurate dimension and location control. In this work, a direct writing method was reported for the in-situ preparation of a high-resolution graphene nanostructure of controllable size (the minimum feature size is about 15 nm), which combines the advantages of e-beam lithography and copper-catalyzed growth. By using the Fourier infrared absorption test, we found that the hydrogen and oxygen elements were disappearing due to knock-on displacement and the radiolysis effect. The graphene crystal is also formed via diffusion and the local heating effect between the e-beam and copper substrate, based on the Raman spectra test. This simple process for the in-situ synthesis of graphene nanostructures has many promising potential applications, including offering a way to make nanoelectrodes, NEMS cantilever resonant structures, nanophotonic devices and so on.

Self-Powered Acceleration Sensor Based on Multilayer Suspension Structure and TPU-RTV Film for Vibration Monitoring.

In this paper, we designed a triboelectric acceleration sensor with excellent multiple parameters. To more easily detect weak vibrations, the sensor was founded on a multilayer suspension structure. To effectively improve the electrical properties of the sensor, a surface roughening and internal doping friction film, which was refined with a room temperature vulcanized silicone rubber (RTV) and some thermoplastic polyurethanes (TPU) powder in a certain proportion, was integrated into the structure. It was found that the optimization of the RTV film increases the open circuit voltage and short circuit current of the triboelectric nanogenerator (TENG) by 223% and 227%, respectively. When the external vibration acceleration is less than 4 m/s2, the sensitivity and linearity are 1.996 V/(m/s2) and 0.999, respectively. Additionally, when it is in the range between 4 m/s2 and 15 m/s2, those are 23.082 V/(m/s2) and 0.975, respectively. Furthermore, the sensor was placed in a simulated truck vibration environment, and its self-powered monitoring ability validated by experiments in real time. The results show that the designed sensor has strong practical value in the field of monitoring mechanical vibration acceleration.

The Wafer-Level Integration of Single-Crystal LiNbO3 on Silicon via Polyimide Material.

In situ measurements of sensing signals in space platforms requires that the micro-electro-mechanical system (MEMS) sensors be located directly at the point to be measured and in contact with the subject to be measured. Traditional radiation-tolerant silicon-based MEMS sensors cannot acquire spatial signals directly. Compared to silicon-based structures, LiNbO3 single crystalline has wide application prospects in the aerospace field owing to its excellent corrosion resistance, low-temperature resistance and radiation resistance. In our work, 4-inch LiNbO3 and LiNbO3/Cr/Au wafers are fabricated to silicon substrate by means of a polyimide bonding method, respectively. The low-temperature bonding process (≤100 °C) is also useful for heterostructure to avoid wafer fragmentation results from a coefficient of thermal expansion (CTE) mismatch. The hydrophilic polyimide surfaces result from the increasing of -OH groups were acquired based on contact angle and X-ray photoelectron spectroscopy characterizations. A tight and defect-free bonding interface was confirmed by scanning electron microscopy. More importantly, benefiting from low-temperature tolerance and radiation-hardened properties of polyimide material, the bonding strength of the heterostructure based on oxygen plasma activation achieved 6.582 MPa and 3.339 MPa corresponding to room temperature and ultra-low temperature (≈ -263.15 °C), which meets the bonding strength requirements of aerospace applications.

High-Performance MIM Capacitors for a Secondary Power Supply Application.

Microstructure is important to the development of energy devices with high performance. In this work, a three-dimensional Si-based metal-insulator-metal (MIM) capacitor has been reported, which is fabricated by microelectromechanical systems (MEMS) technology. Area enlargement is achieved by forming deep trenches in a silicon substrate using the deep reactive ion etching method. The results indicate that an area of 2.45 × 10³ mm² can be realized in the deep trench structure with a high aspect ratio of 30:1. Subsequently, a dielectric Al2O3 layer and electrode W/TiN layers are deposited by atomic layer deposition. The obtained capacitor has superior performance, such as a high breakdown voltage (34.1 V), a moderate energy density (≥1.23 mJ/cm²) per unit planar area, a high breakdown electric field (6.1 ± 0.1 MV/cm), a low leakage current (10-7 A/cm² at 22.5 V), and a low quadratic voltage coefficient of capacitance (VCC) (≤63.1 ppm/V²). In addition, the device's performance has been theoretically examined. The results show that the high energy supply and small leakage current can be attributed to the Poole⁻Frenkel emission in the high-field region and the trap-assisted tunneling in the low-field region. The reported capacitor has potential application as a secondary power supply.

Stretchable Triboelectric Textile Composed of Wavy Conductive-Cloth PET and Patterned Stretchable Electrode for Harvesting Multivariant Human Motion Energy.

Triboelectric textile with wearable property and feasibility of large area preparation has presented a great prospect in effectively collecting energy from human body motion to provide power supply for diversified wearable electronics. Here, we report a stretchable triboelectric textile (STET) composed of wavy conductive-cloth poly(ethylene terephthalate) and a patterned stretchable electrode as basic knitting units, which can achieve multivariant energy harvest with low cost and good comfort. STET displays excellent output performances due to diversified working principles of contact-separation and contact-sliding modes. Interaction between the knitting units can generate open-circuit voltage with a peak-to-peak value of 350 V and instantaneous peak power of 1 mW; the stretched-released STET produces a peak voltage of 32 V, whereas tapping the STET with cotton twice gives contact-separation movements generating improved peak voltage and current. To prove the potential application, the STET is fixed onto different positions of a human body to effectively harvest multivariant human body motion energy. Therefore, this work provides a new approach applying stretchable triboelectric textile for power supply in wearable devices.

Potential sensitivities in frequency modulation and heterodyne amplitude modulation Kelvin probe force microscopes.

In this paper, the potential sensitivity in Kelvin probe force microscopy (KPFM) was investigated in frequency modulation (FM) and heterodyne amplitude modulation (AM) modes. We showed theoretically that the minimum detectable contact potential difference (CPD) in FM-KPFM is higher than in heterodyne AM-KPFM. We experimentally confirmed that the signal-to-noise ratio in FM-KPFM is lower than that in heterodyne AM-KPFM, which is due to the higher minimum detectable CPD dependence in FM-KPFM. We also compared the corrugations in the local contact potential difference on the surface of Ge (001), which shows atomic resolution in heterodyne AM-KPFM. In contrast, atomic resolution cannot be obtained in FM-KPFM under the same experimental conditions. The higher potential resolution in heterodyne AM-KPFM was attributed to the lower crosstalk and higher potential sensitivity between topographic and potential measurements.