RESUMO
Herein we report the synthesis and characterization of spinel copper gallate (CuGa2O4) nanocrystals (NCs) with an average size of 3.7 nm via a heat-up colloidal reaction. CuGa2O4 NCs have a band gap of â¼2.5 eV and marked p-type character, in agreement with ab initio simulations. These novel NCs are demonstrated to be photoactive, generating a clear and reproducible photocurrent under blue light irradiation when deposited as thin films. Crucially, the ability to adjust the Cu/Ga ratio within the NCs, and the effect of this on the optical and electronic properties of the NCs, was also demonstrated. These results position CuGa2O4 NCs as a novel material for optoelectronic applications, including hole transport and light harvesting.
RESUMO
Ionic liquids are versatile solvents that can be tailored through modification of the cation and anion species. Relatively little is known about the corrosive properties of protic ionic liquids. In this study, we have explored the corrosion of both zinc and copper within a series of protic ionic liquids consisting of alkylammonium or alkanolammonium cations paired with nitrate or carboxylate anions along with three aprotic imidazolium ionic liquids for comparison. Electrochemical studies revealed that the presence of either carboxylate anions or alkanolammonium cations tend to induce a cathodic shift in the corrosion potential. The effect in copper was similar in magnitude for both cations and anions, while the anion effect was slightly more pronounced than that of the cation in the case of zinc. For copper, the presence of carboxylate anions or alkanolammonium cations led to a notable decrease in corrosion current, whereas an increase was typically observed for zinc. The ionic liquid-metal surface interactions were further explored for select protic ionic liquids on copper using X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) to characterize the interface. From these studies, the oxide species formed on the surface were identified, and copper speciation at the surface linked to ionic liquid and potential dependent surface passivation. Density functional theory and ab initio molecular dynamics simulations revealed that the ethanolammonium cation was more strongly bound to the copper surface than the ethylammonium counterpart. In addition, the nitrate anion was more tightly bound than the formate anion. These likely lead to competing effects on the process of corrosion: the tightly bound cations act as a source of passivation, whereas the tightly bound anions facilitate the electrodissolution of the copper.
RESUMO
Lateral memristors configured with inert Pt contacts and mixed phase tin oxide layers have exhibited immediate, forming-free, low-power bidirectional resistance switching. Activity dependent conductance and relaxation in the low resistance state resembled short term potentiation in biological synapses. After scanning probe microscopy, x-ray photoelectron spectroscopy and electrical measurements, the device characteristics were attributed to Joule heating induced decomposition of the minority SnO phase and formation of a SnO2 conducting filament with higher effective n-type doping. Finally, the devices recognized input voltage pulse sequences and spectral data by returning unique conductance states, suggesting suitability for bio-inspired pattern recognition systems.
RESUMO
The oscillatory palladium-catalysed carbonylation reaction opens new horizons for applications in smart materials due to the versatility of its conditions and substrates, as well as the adjustability of amplitude and period of pH oscillations. A variety of viable substrates have been demonstrated, including polymeric alkyne-terminated substrates. However, so far, there have not been any reports of polymer-based palladium catalysts in oscillatory mode. In this paper, we demonstrate pH oscillations in various systems, using commercially available palladium acetate, a triphenylphosphine palladium acetate complex and a polymer-bound palladium catalyst. While palladium acetate was able to generate oscillations under the conditions already established in our previous research on PdI2-catalysed oscillators, the other two catalysts needed the addition of HI to induce oscillations. HI forced an initial pH drop, bringing pH into the range where oscillations generally occur. Addition of HI had a significant effect on all catalysts, modifying the amplitude and period of oscillations, oscillation mode, as well as starting material conversion and product distribution.
RESUMO
Two-dimensional (2D) wide bandgap materials are gaining significant interest for next-generation optoelectronic devices. However, fabricating electronic-grade 2D nanosheets from non-van der Waals (n-vdW) oxide semiconductors poses a great challenge due to their stronger interlayer coupling compared with vdW crystals. This strong coupling typically introduces defects during exfoliation, impairing the optoelectronic properties. Herein, we report the liquid-phase exfoliation of few-atomic-layer thin, defect-free, free-standing ZnO nanosheets. These micron-sized, ultrathin ZnO structures exhibit three different orientations aligned along both the polar c-plane as well as the nonpolar a- and m-planes. The superior crystalline quality of the ZnO nanosheets is validated through comprehensive characterization techniques. This result is supported by density functional theory (DFT) calculations, which reveals that the formation of oxygen vacancies is energetically less favorable in 2D ZnO and that the c-plane loses its polarity upon exfoliation. Unlike bulk ZnO, which is typically dominated by defect-induced emission, the exfoliated nanosheets exhibit a strong, ambient-stable excitonic UV emission. We further demonstrate the utility of solution processing of ZnO nanosheets by their hybrid integration with organic components to produce stable light emitting diodes (LEDs) for display applications.
RESUMO
Photodetector technology has evolved significantly over the years with the emergence of new active materials. However, there remain trade-offs between spectral sensitivity, operating energy, and, more recently, an ability to harbor additional features such as persistent photoconductivity and bidirectional photocurrents for new emerging application areas such as switchable light imaging and filter-less color discrimination. Here, we demonstrate a self-powered bidirectional photodetector based on molybdenum disulfide/gallium nitride (MoS2/GaN) epitaxial heterostructure. This fabricated detector exhibits self-powered functionality and achieves detection in two discrete wavelength bands: ultraviolet and visible. Notably, it attains a peak responsivity of 631 mAW-1 at a bias of 0V. The device's response to illumination at these two wavelengths is governed by distinct mechanisms, activated under applied bias conditions, thereby inducing a reversal in the polarity of the photocurrent. This work underscores the feasibility of self-powered and bidirectional photocurrent detection but also opens new vistas for technological advancements for future optoelectronic, neuromorphic, and sensing applications.
RESUMO
MXenes hold immense potential given their superior electrical properties. The practical adoption of these promising materials is, however, severely constrained by their oxidative susceptibility, leading to significant performance deterioration and lifespan limitations. Attempts to preserve MXenes have been limited, and it has not been possible thus far to reverse the material's performance. In this work, we show that subjecting oxidized micron or nanometer thickness dry MXene films-even those constructed from nanometer-order solution-dispersed oxidized flakes-to just one minute of 10 MHz nanoscale electromechanical vibration leads to considerable removal of its surface oxide layer, whilst preserving its structure and characteristics. Importantly, electrochemical performance is recovered close to that of their original state: the pseudocapacitance, which decreased by almost 50% due to its oxidation, reverses to approximately 98% of its original value, with good capacitance retention ( ≈ 93%) following 10,000 charge-discharge cycles at 10 A g-1. These promising results allude to the exciting possibility for rejuvenating the material for reuse, therefore offering a more economical and sustainable route that improves its potential for practical translation.
RESUMO
A way through which the properties of metal-organic frameworks (MOFs) can be tuned is by engineering defects into the crystal structure. Given its intrinsic stability and rigidity, however, it is difficult to introduce defects into zeolitic imidazolate frameworks (ZIFs)-and ZIF-8, in particular-without compromising crystal integrity. In this work, it is shown that the acoustic radiation pressure as well as the hydrodynamic stresses arising from the oscillatory flow generated by coupling high frequency (MHz-order) hybrid surface and bulk acoustic waves into a suspension of ZIF-8 crystals in a liquid pressure transmitting medium is capable of driving permanent structural changes in their crystal lattice structure. Over time, the enhancement in the diffusive transport of guest molecules into the material's pores as a consequence is shown to lead to expansion of the pore framework, and subsequently, the creation of dangling-linker and missing-linker defects, therefore offering the possibility of tuning the type and extent of defects engineered into the MOF through the acoustic exposure time. Additionally, the practical utility of the technology is demonstrated for one-pot, simultaneous solvent-assisted ligand exchange under ambient conditions, for sub-micron-dimension ZIF-8 crystals and relatively large ligands-more specifically 2-aminobenzimidazole-without compromising the framework porosity or overall crystal structure.
RESUMO
Polydimethyl glutarimide (PMGI) layers with sub-micron thicknesses have been modified in a 2.5 kV Ar plasma immersion ion implantation (PIII) process to introduce free radical covalent binding sites. The surface roughness of the PMGI increased after the PIII treatment but no through-layer defects were observed. When applied to the treated PMGI, horseradish peroxidase (HRP) enzyme remained bound to the surface after extended immersion in sodium dodecyl sulfate solution (SDS). Hence, covalent binding between the activated surface and enzyme was confirmed. This covalent binding was achieved up to 24-h after the PIII process. The treated PMGI was then incorporated as a gate dielectric layer within a lateral three-terminal electrolyte-gated device. The device output characteristics resembled those of post-synaptic outputs; as successive (pre-synaptic) voltage pulses were applied to the gate, paired pulse depression and spike rate dependent plasticity were observed in the source-drain (post-synaptic) current. These characteristics were altered by the presence of HRP immobilised on the plasma-modified PMGI gate dielectric layer thus providing readout detection. These results and preliminary device characteristics show the potential for the plasma functionalized PMGI as a sensitive and reproducible biosensing technology.
Assuntos
Piperidonas , Dodecilsulfato de Sódio , Enzimas Imobilizadas/química , Íons , Peroxidase do Rábano Silvestre/químicaRESUMO
Telomerase, a ribonucleoprotein coded by the hTERT gene, plays an important role in cellular immortalization and carcinogenesis. hTERT is a suitable target for cancer therapeutics as its activity is highly upregulated in most of cancer cells but absent in normal somatic cells. Here, by employing the two Metal-Organic Frameworks (MOFs), viz. ZIF-C and ZIF-8, based biomineralization we encapsulate Clustered Regularly Interspaced Short Palindromic Repeat (CRISPR)/Cas9 plasmid system that targets hTERT gene (CrhTERT) in cancer cells. When comparing the two biocomposites, ZIF-C shows the better loading capacity and cell viability. The loaded plasmid in ZIF-C is highly protected against enzymatic degradation. CrhTERT@ZIF-C is efficiently endocytosed by cancer cells and the subcellular release of CrhTERT leads to telomerase knockdown. The resultant inhibition of hTERT expression decreases cellular proliferation and causing cancer cell death. Furthermore, hTERT knockdown shows a significant reduction in tumour metastasis and alters protein expression. Collectively we show the high potential of ZIF-C-based biocomposites as a promising general tool for gene therapy of different types of cancers.
Assuntos
Neoplasias , Telomerase , Zeolitas , Telomerase/genética , Telomerase/metabolismo , Zeolitas/metabolismo , Linhagem Celular , Imidazóis/farmacologia , Terapia Genética , Neoplasias/genética , Neoplasias/terapiaRESUMO
The resistive switching response of two terminal metal/oxide/metal devices depends on the stoichiometry of the oxide film, and this is commonly controlled by using a reactive metal electrode to reduce the oxide layer. Here, we investigate compositional and structural changes induced in Nb/Nb2O5 bilayers by thermal annealing at temperatures in the range of 573-973 K and its effect on the volatile threshold switching characteristics of Nb/Nb2O5/Pt devices. Changes in the stoichiometry of the Nb and Nb2O5 films are determined by Rutherford backscattering spectrometry and energy-dispersive X-ray (EDX) mapping of sample cross sections, while the structure of the films is determined by X-ray diffraction, Raman spectroscopy, and transmission electron microscopy (TEM). Such analysis shows that the composition of the Nb and Nb2O5 layers is homogenized by interdiffusion at temperatures less than the crystallization temperature (i.e., >773 K) but that this effectively ceases once the films crystallize. This is explained by comparison with the predictions of a simple diffusion model which shows that the compositional changes are dominated by oxygen diffusion in the amorphous oxide, which is much faster than that in the crystalline phases. We further show that these compositional and structural changes have a significant effect on the electroforming and threshold switching characteristics of the devices, the most significant being a marked increase in their reliability and endurance after crystallization of the oxide films. Finally, we examine the effect of annealing on the quasistatic negative differential resistance characteristics and oscillator dynamics of devices and use a lumped element model to show that this is dominated by changes in the device capacitance resulting from interdiffusion.
RESUMO
Despite recent advances in the development of orthopedic devices, implant-related failures that occur as a result of poor osseointegration and nosocomial infection are frequent. In this study, we developed a multiscale titanium (Ti) surface topography that promotes both osteogenic and mechano-bactericidal activity using a simple two-step fabrication approach. The response of MG-63 osteoblast-like cells and antibacterial activity toward Pseudomonas aeruginosa and Staphylococcus aureus bacteria was compared for two distinct micronanoarchitectures of differing surface roughness created by acid etching, using either hydrochloric acid (HCl) or sulfuric acid (H2SO4), followed by hydrothermal treatment, henceforth referred to as either MN-HCl or MN-H2SO4. The MN-HCl surfaces were characterized by an average surface microroughness (Sa) of 0.8 ± 0.1 µm covered by blade-like nanosheets of 10 ± 2.1 nm thickness, whereas the MN-H2SO4 surfaces exhibited a greater Sa value of 5.8 ± 0.6 µm, with a network of nanosheets of 20 ± 2.6 nm thickness. Both micronanostructured surfaces promoted enhanced MG-63 attachment and differentiation; however, cell proliferation was only significantly increased on MN-HCl surfaces. In addition, the MN-HCl surface exhibited increased levels of bactericidal activity, with only 0.6% of the P. aeruginosa cells and approximately 5% S. aureus cells remaining viable after 24 h when compared to control surfaces. Thus, we propose the modulation of surface roughness and architecture on the micro- and nanoscale to achieve efficient manipulation of osteogenic cell response combined with mechanical antibacterial activity. The outcomes of this study provide significant insight into the further development of advanced multifunctional orthopedic implant surfaces.
Assuntos
Staphylococcus aureus , Titânio , Titânio/farmacologia , Propriedades de Superfície , Osteogênese , Antibacterianos/farmacologiaRESUMO
Plastic pollution is recognized as a major environmental problem in many countries. Over the last decade, academics have embraced research on bioplastics to discover newer high-end green materials. However, the end-of-life environmental fate of such materials is not adequately understood. Non-isocyanate polyhydroxyurethanes (PHUs) are green engineering materials with huge potential to replace traditional polyurethanes. Despite this immense potential, a number of questions about their environmental fate remain unanswered. The present study investigated the extent and mechanisms underlying soil biodegradation of PHUs and determined whether the deterioration of PHUs within starch bioplastics (ST) can improve the biodegradation of starch (ST)-PHU hybrids. Soil microbiomes managed to effectively and quickly digest not only PHUs but also ST-PHU hybrids. All ST-PHU hybrids were characterized by exceptional biodegradability with mass losses of up to ~88% following a soil burial time of only 120 days. The biodegradation of ST-alone bioplastics was 69% under identical conditions. The presence of cellulose nanocrystals (CNC) reduced the potential for the soil microbial community to degrade nanohybrids (ST-PHU-CNC). Microbially digested bioplastics with PHU presented less stages of thermal degradation, and reduced intensities of FTIR, NMR and XPS signals compared to the original films, indicating improvement of the biodegradation mechanism. These findings suggested the positive environmental implications of PHU in improving the bioplastic's degradation and their potential for future applications.
Assuntos
Nanopartículas , Amido , Biodegradação Ambiental , Celulose , Plásticos , SoloRESUMO
The emergence of attractive properties in materials at atomically thin regimes has seen an ongoing interest in two-dimensional (2D) materials. An aspect that has lacked focused attention is the effect of 2D material thickness on its crystal structure. As several layered materials naturally exist in mixed metastable phases, it raises an important question of whether a specific polymorph of these mixed-phase materials will be favored at atomically thin limits. This work attempts to address this issue by employing lead monoxide as a model 2D polymorphic system. We propose a reactive oxygen species (ROS) sequestration-mediated liquid-phase exfoliation (LPE) strategy for the facile synthesis of ultrathin PbO. This is followed by a suite of microscopic and spectroscopic analyses of the PbO nanosheets that reveals the polymorphic transformation of orthorhombic (ß) PbO to its tetragonal (α) analogue with reduction in nanosheet thickness. The transformation process reveals an interesting crystal structure of ultrathin 2D PbO where [001]-oriented domains of α-PbO coexist alongside [100]-oriented regions of ß-PbO. Density functional theory (DFT) calculations support our experimental data by revealing a higher thermodynamic stability of the tetragonal phase in PbO monolayers. These findings are likely to instigate interest in carefully evaluating the crystal structures of ultrathin 2D materials while promoting research in understanding the phase transformation across a range of 2D crystals.
RESUMO
The development of high-performing p-type transparent conducting oxides will enable immense progress in the fabrication of optoelectronic devices including invisible electronics and all-oxide power electronics. While n-type transparent electrodes have already reached widespread industrial production, the lack of p-type counterparts with comparable transparency and conductivity has created a bottleneck for the development of next-generation optoelectronic devices. In this work, we present the fabrication of delafossite copper chromium oxide p-type transparent electrodes with outstanding optical and electrical properties. These layers were deposited using ultrasonic spray pyrolysis, a wet chemical method that is fast, simple, and scalable. Through careful screening of the deposition conditions, highly crystalline, dense, and smooth CuCrO2 coatings were obtained. A detailed investigation of the role played by the deposition temperature and the cation ratio enabled the properties of the prepared layers to be reliably tuned, as verified using X-ray diffraction, X-ray photoelectron spectroscopy, optical spectroscopy, Hall effect measurements, and electron and atomic force microscopies. We demonstrate record conductivities for solution-processed CuCrO2, exceeding 100 S cm-1, and we also obtained the highest value for two separate figures of merit for p-type transparent conducting oxides. These performances position solution-deposited CuCrO2 as the leading p-type transparent-conducting oxide currently available.
RESUMO
Graphene oxide quantum dots (GOQDs) hold great promise as a new class of high-performance carbonaceous nanomaterials due to their numerous functional properties, such as tunable photoluminescence (PL), excellent thermal and chemical stability, and superior biocompatibility. In this study, we developed a facile, one-pot, and effective strategy to engineer the interface of GOQDs through covalent doping with silicon. The successful covalent attachment of the silane dopant with pendant vinyl groups to the edges of the GOQDs was confirmed by an in-depth investigation of the structural and morphological characteristics. The Si-GOQD nanoconjugates had an average dimension of â¼8 nm, with a graphite-structured core and amorphous carbon on their shell. We further used the infrared nanoimaging based on scattering-type scanning near-field optical microscopy to unveil the spectral near-field response of GOQD samples and to measure the nanoscale IR response of its network; we then demonstrated their distinct domains with strongly enhanced near fields. The doping of Si atoms into the sp2-hybridized graphitic framework of GOQDs also led to tailored PL emissions. We then sought to explore the potential applications of Si-GOQDs on the surface of plastic films where poly(dimethylsiloxane) (PDMS) served as a bridge to tightly anchor the Si-GOQDs to the surface. The bi-layered coated films which were built with co-assembly of Si-GOQDs and PDMS contributed to suppressing the transmission of water molecules due to the generation of compact and less accessible passing sites, achieving a nearly twofold reduction in water permeability compared to the single-layered coated films. The nanoindentation and PeakForce quantitative nanomechanical mapping showed that Si-GOQD-coated substrates were softer and more deformable than those coated only with PDMS. The co-assembly of PDMS and Si-GOQDs yielded films that were less stiff than those made from PDMS alone. Our findings provided conceptual insights into the importance of nanoscale surface engineering of GOQDs in conferring excellent dispersibility and enhancing the performance of nanocomposite films.
RESUMO
HYPOTHESIS: Titanium and its alloys are commonly used implant materials. Once inserted into the body, the interface of the biomaterials is the most likely site for the development of implant-associated infections. Imparting the titanium substrate with high-aspect-ratio nanostructures, which can be uniformly achieved using hydrothermal etching, enables a mechanical contact-killing (mechanoresponsive) mechanism of bacterial and fungal cells. Interaction between cells and the surface shows cellular inactivation via a physical mechanism meaning that careful engineering of the interface is needed to optimse the technology. This mechanism of action is only effective towards surface adsorbed microbes, thus any cells not directly in contact with the substrate will survive and limit the antimicrobial efficacy of the titanium nanostructures. Therefore, we propose that a dual-action mechanoresponsive and chemical-surface approach must be utilised to improve antimicrobial activity. The addition of antimicrobial silver nanoparticles will provide a secondary, chemical mechanism to escalate the microbial response in tandem with the physical puncture of the cells. EXPERIMENTS: Hydrothermal etching is used as a facile method to impart variant nanostrucutres on the titanium substrate to increase the antimicrobial response. Increasing concentrations (0.25 M, 0.50 M, 1.0 M, 2.0 M) of sodium hydroxide etching solution were used to provide differing degrees of nanostructured morphology on the surface after 3 h of heating at 150 °C. This produced titanium nanospikes, nanoblades, and nanowires, respectively, as a function of etchant concentration. These substrates then provided an interface for the deposition of silver nanoparticles via a reduction pathway. Methicillin-resistant Staphylococcous aureus (MRSA) and Candida auris (C. auris) were used as model bacteria and fungi, respectively, to test the effectiveness of the nanostructured titanium with and without silver nanoparticles, and the bio-interactions at the interface. FINDINGS: The presence of nanostructure increased the bactericidal response of titanium against MRSA from â¼ 10 % on commercially pure titanium to a maximum of â¼ 60 % and increased the fungicidal response from â¼ 10 % to â¼ 70 % in C. auris. Introducing silver nanoparticles increased the microbiocidal response to â¼ 99 % towards both bacteria and fungi. Importantly, this study highlights that nanostructure alone is not sufficient to develop a highly antimicrobial titanium substrate. A dual-action, physical and chemical antimicrobial approach is better suited to produce highly effective antibacterial and antifungal surface technologies.
Assuntos
Anti-Infecciosos , Nanopartículas Metálicas , Nanoestruturas , Prata/farmacologia , Prata/química , Titânio/farmacologia , Titânio/química , Nanopartículas Metálicas/química , Antifúngicos/farmacologia , Hidróxido de Sódio , Nanoestruturas/química , Bactérias , Antibacterianos/farmacologia , Antibacterianos/química , Ligas/farmacologia , Anti-Infecciosos/farmacologia , Materiais Biocompatíveis/farmacologiaRESUMO
Indium nitride (InN) has been of significant interest for creating and studying two-dimensional electron gases (2DEG). Herein we demonstrate the formation of 2DEGs in ultrathin doped and undoped 2D InN nanosheets featuring high carrier mobilities at room temperature. The synthesis is carried out via a two-step liquid metal-based printing method followed by a microwave plasma-enhanced nitridation reaction. Ultrathin InN nanosheets with a thickness of â¼2 ± 0.2 nm were isolated over large areas with lateral dimensions exceeding centimeter scale. Room temperature Hall effect measurements reveal carrier mobilities of â¼216 and â¼148 cm2 V-1 s-1 for undoped and doped InN, respectively. Further analysis suggests the presence of defined quantized states in these ultrathin nitride nanosheets that can be attributed to a 2D electron gas forming due to strong out-of-plane confinement. Overall, the combination of electronic and plasmonic features in undoped and doped ultrathin 2D InN holds promise for creating advanced optoelectronic devices and functional 2D heterostructures.
RESUMO
The use of superhydrophobic surfaces in a broad range of applications is receiving a great deal of attention due to their numerous functionalities. However, fabricating these surfaces using low-cost raw materials through green and fluorine-free routes has been a bottleneck in their industrial deployment. This work presents a facile and environmentally friendly strategy to prepare mechanically robust superhydrophobic surfaces with engineered lotus leaf mimetic multiscale hierarchical structures via a hybrid route combining soft imprinting and spin-coating. Direct soft-imprinting lithography onto starch/polyhydroxyurethane/cellulose nanocrystal (SPC) films formed micro-scaled features resembling the pillar architecture of lotus leaf. Spin-coating was then used to assemble a thin layer of low-surface-energy poly(dimethylsiloxane) (PDMS) over these microstructures. Silica nanoparticles (SNPs) were grafted with vinyltriethoxysilane (VTES) to form functional silica nanoparticles (V-SNPs) and subsequently used for the fabrication of superhydrophobic coatings. A further modification of PDMS@SPC film with V-SNPs enabled the interlocking of V-SNPs microparticles within the cross-linked PDMS network. The simultaneous introduction of hierarchical microscale surface topography, the low surface tension of the PDMS layer, and the nanoscale roughness induced by V-SNPs contributed to the fabrication of a superhydrophobic interface with a water contact angle (WCA) of â¼150° and a sliding angle (SA) of <10°. The PDMS/V-SNP@SPC films showed an â¼52% reduction in water vapor transmission rate compared to that of uncoated films. These results indicated that the coating served as an excellent moisture barrier and imparted good hydrophobicity to the film substrate. The coated film surfaces were able to withstand extensive knife scratches, finger-rubbing, jet-water impact, a sandpaper-abrasion test for 20 cycles, and a tape-peeling test for â¼10 repetitions without losing superhydrophobicity, suggesting superior mechanical durability. Self-cleaning behavior was also demonstrated when the surfaces were cleared of artificial dust and various food liquids. The green and innovative approach presented in the current study can potentially serve as an attractive new tool for the development of robust superhydrophobic surfaces without adverse environmental consequences.
RESUMO
Owing to several key attributes, diamond is an attractive candidate material for neural interfacing electrodes. The emergence of additive-manufacturing (AM) of diamond-based materials has addressed multiple challenges associated with the fabrication of diamond electrodes using the conventional chemical vapor deposition (CVD) approach. Unlike the CVD approach, AM methods have enabled the deposition of three-dimensional diamond-based material at room temperature. This work demonstrates the feasibility of using laser metal deposition to fabricate diamond-titanium hybrid electrodes for neuronal interfacing. In addition to exhibiting a high electrochemical capacitance of 1.1 mF cm-2 and a low electrochemical impedance of 1 kΩ cm2 at 1 kHz in physiological saline, these electrodes exhibit a high degree of biocompatibility assessed in vitro using cortical neurons. Furthermore, surface characterization methods show the presence of an oxygen-rich mixed-phase diamond-titanium surface along the grain boundaries. Overall, we demonstrated that our unique approach facilitates printing biocompatible titanium-diamond site-specific coating-free conductive hybrid surfaces using AM, which paves the way to printing customized electrodes and interfacing implantable medical devices.