Structure/Property Relations in "Giant" Semiconductor Nanocrystals: Opportunities in Photonics and Electronics.

Semiconductor nanocrystals exhibit size-tunable absorption and emission ranging from the ultraviolet (UV) to the near-infrared (NIR) spectral range, high absorption coefficient, and high photoluminescence quantum yield. Effective surface passivation of these so-called quantum dots (QDs) may be achieved by growing a shell of another semiconductor material. The resulting core/shell QDs can be considered as a model system to study and optimize structure/property relations. A special case consists in growing thick shells (1.5 up to few tens of nanometers) to produce "giant" QDs (g-QDs). Tailoring the chemical composition and structure of CdSe/CdS and PbS/CdS g-QDs is a promising approach to widen the spectral separation of absorption and emission spectra (i.e., the Stokes shift), improve the isolation of photogenerated carriers from surface defects and enhance charge carrier lifetime and mobility. However, most stable systems are limited by a thick CdS shell, which strongly absorbs radiation below 500 nm, covering the UV and part of the visible range. Modification of the interfacial region between the core and shell of g-QDs or tuning their doping with narrow band gap semiconductors are effective approaches to circumvent this challenge. In addition, the synthesis of g-QDs composed of environmentally friendly elements (e.g., CuInSe2/CuInS2) represents an alternative to extend their absorption into the NIR range. Additionally, the band gap and band alignment of g-QDs can be engineered by proper selection of the constituents according to their band edge positions and by tuning their stoichiometry during wet chemical synthesis. In most cases, the quasi-type II localization regime of electrons and holes is achieved. In this type of g-QDs, electrons can leak into the shell region, while the holes remain confined within the core region. This electron-hole spatial distribution is advantageous for optoelectronic devices, resulting in efficient electron-hole separation while maintaining good stability. This Account provides an overview of emerging engineering strategies that can be adopted to optimize structure/property relations in colloidal g-QDs for efficient photon management or charge separation/transfer. In particular, we focus on our recent contributions to this rapidly expanding field of research. We summarize the design and synthesis of a variety of colloidal g-QDs with the aim of tuning the optical properties, such as absorption/emission in a wide region of the solar spectrum, which allows enlargement of their Stokes shift. We also describe the band alignment within these systems, charge carrier dynamics, and charge transfer from g-QDs into semiconducting oxides. We show how these tailored g-QDs may be used as active components in luminescent solar concentrators, photoelectrochemical cells for hydrogen generation, QD-sensitized solar cells and optical nanothermometers. In each case, we aim at providing insights on structure/property relationships and on how to optimize them toward improving device performance. Finally, we describe perspectives for future work, sketching new directions and opportunities in this field of research at the intersection between chemistry, physics, materials science and engineering.

Surface engineering of two-dimensional hexagonal boron-nitride for optoelectronic devices.

Two-dimensional hexagonal boron nitride (2D h-BN) is being extensively studied in optoelectronic devices due to its electronic and photonic properties. However, the controlled optimization of h-BN's insulating properties is necessary to fully explore its potential in energy conversion and storage devices. In this work, we engineered the surface of h-BN nanoflakes via one-step in situ chemical functionalization using a liquid-phase exfoliation approach. The functionalized h-BN (F-h-BN) nanoflakes were subsequently dispersed on the surface of TiO2 to tune the TiO2/QDs interface of the optoelectronic device. The photoelectrochemical (PEC) devices based on TiO2/F-h-BN/QDs with optimized addition of carbon nanotubes (CNTs) and scattering layers showed 46% improvement compared to the control device (TiO2/QDs). This significant improvement is attributed to the reduced trap/carrier recombination and enhanced carrier injection rate of the TiO2-CNTs/F-h-BN/QDs photoanode. Furthermore, by employing an optimized TiO2-CNTs/F-h-BN/QDs photoanode, QDs-sensitized solar cells (QDSCs) yield an 18% improvement in photoconversion efficiency. This represents a potential and adaptability of our approach, and pathway to explore surface-engineered 2D materials to optimize the interface of solar energy conversion and other emerging optoelectronic devices.

Synergistic Effect of Plasmonic Gold Nanoparticles Decorated Carbon Nanotubes in Quantum Dots/TiO2 for Optoelectronic Devices.

Here, a facile approach to enhance the performance of solar-driven photoelectrochemical (PEC) water splitting is described by means of the synergistic effects of a hybrid network of plasmonic Au nanoparticles (NPs) decorated on multiwalled carbon nanotubes (CNTs). The device based on TiO2-Au:CNTs hybrid network sensitized with colloidal CdSe/(CdSe x S1- x )5/(CdS)1 core/alloyed shell quantum dots (QDs) yields a saturated photocurrent density of 16.10 ± 0.10 mA cm-2 [at 1.0 V vs reversible hydrogen electrode (RHE)] under 1 sun illumination (AM 1.5G, 100 mW cm-2), which is ≈26% higher than the control device. The in-depth mechanism behind this significant improvement is revealed through a combined experimental and theoretical analysis for QDs/TiO2-Au:CNTs hybrid network and demonstrates the multifaceted impact of plasmonic Au NPs and CNTs: i) hot-electron injection from Au NPs into CNTs and TiO2; ii) near-field enhancement of the QDs absorption and carrier generation/separation processes by the plasmonic Au NPs; iii) enhanced photoinjected electron transport due to the highly directional pathways offered by CNTs. These results provide fundamental insights on the properties of QDs/TiO2-Au:CNTs hybrid network, and highlights the possibility to improve the performance of other solar technologies.

A colloidal heterostructured quantum dot sensitized carbon nanotube-TiO2 hybrid photoanode for high efficiency hydrogen generation.

Solar-driven photoelectrochemical (PEC) hydrogen (H2) generation is a promising approach to harvest solar energy for the production of a clean chemical fuel. However, the low photon-to-fuel conversion efficiency and long-term stability of PEC devices are major challenges to be addressed to enable large-scale commercialization. Here we report a simple, fast and cost-effective approach to fabricate high efficiency and stable PEC devices for H2 generation, by fabricating a hybrid photoanode obtained by incorporating small amounts of multiwall carbon nanotubes (MWCNTs) into a TiO2 mesoporous film and sensitizing with colloidal heterostructured CdSe/(CdSexS1-x)5/(CdS)2 quantum dots (QDs). The latter were specially designed to accelerate the exciton separation through a band engineering approach. The PEC devices based on the TiO2/QD-MWCNT (T/Q-M) hybrid photoanode with an optimized amount of MWCNTs (0.015 wt%) yield a saturated photocurrent density of 15.90 mA cm-2 (at 1.0 VRHE) under one sun illumination (AM 1.5G, 100 mW cm-2), which is 40% higher than that of the reference device based on TiO2/QD (T/Q) photoanodes. This is attributed to a synergistic effect of the promising optoelectronic properties of the colloidal heterostructured QDs and improved electron transport (reduced charge transfer resistance) within the TiO2-MWCNT hybrid anodes enabled by the directional path of MWCNTs for the photo-injected electrons towards FTO. Furthermore, the PEC device based on the T/Q-M hybrid photoanode is more stable (∼19% loss of its initial photocurrent density) when compared with the T/Q photoanode (∼35% loss) after two hours of continuous one sun illumination. Our results provide fundamental insights and a different approach to improve the efficiency and long-term stability of PEC devices and represent an essential step towards the commercialization of this emerging solar-to-fuel conversion technology.

Highly stable photoelectrochemical cells for hydrogen production using a SnO2-TiO2/quantum dot heterostructured photoanode.

Photoelectrochemical (PEC) water splitting implementing colloidal quantum dots (QDs) as sensitizers is a promising approach for hydrogen (H2) generation, due to the QD's size-tunable optical properties. However, the challenge of long-term stability of the QDs is still unresolved. Here, we introduce a highly stable QD-based PEC device for H2 generation using a photoanode based on a SnO2-TiO2 heterostructure, sensitized by CdSe/CdS core/thick-shell "giant" QDs. This hybrid photoanode architecture leads to an appreciable saturated photocurrent density of ∼4.7 mA cm-2, retaining an unprecedented ∼96% of its initial current density after two hours, and sustaining ∼93% after five hours of continuous irradiation under an AM 1.5G (100 mW cm-2) simulated solar spectrum. Transient photoluminescence (PL) measurements demonstrate that the heterostructured SnO2-TiO2 photoanode exhibits faster electron transfer compared with the bare TiO2 photoanode. The lower electron transfer rate in the TiO2 photoanode can be attributed to slow electron kinetics in the ultraviolet regime, revealed by ultrafast transient absorption spectroscopy. Graphene microplatelets were further introduced into the heterostructured photoanode, which boosted the photocurrent density to ∼5.6 mA cm-2. Our results demonstrate that the SnO2-TiO2 heterostructured photoanode holds significant potential for developing highly stable PEC cells.

Optoelectronic Properties in Near-Infrared Colloidal Heterostructured Pyramidal "Giant" Core/Shell Quantum Dots.

Colloidal heterostructured quantum dots (QDs) are promising candidates for next-generation optoelectronic devices. In particular, "giant" core/shell QDs (g-QDs) can be engineered to exhibit outstanding optical properties and high chemical/photostability for the fabrication of high-performance optoelectronic devices. Here, the synthesis of heterostructured CuInSe x S2-x (CISeS)/CdSeS/CdS g-QDs with pyramidal shape by using a facile two-step method is reported. The CdSeS/CdS shell is demonstrated to have a pure zinc blend phase other than typical wurtzite phase. The as-obtained heterostructured g-QDs exhibit near-infrared photoluminescence (PL) emission (≈830 nm) and very long PL lifetime (in the microsecond range). The pyramidal g-QDs exhibit a quasi-type II band structure with spatial separation of electron-hole wave function, suggesting an efficient exciton extraction and transport, which is consistent with theoretical calculations. These heterostructured g-QDs are used as light harvesters to fabricate a photoelectrochemical cell, exhibiting a saturated photocurrent density as high as ≈5.5 mA cm-2 and good stability under 1 sun illumination (AM 1.5 G, 100 mW cm-2). These results are an important step toward using heterostructured pyramidal g-QDs for prospective applications in solar technologies.

Controlled synthesis of near-infrared quantum dots for optoelectronic devices.

We designed a facile approach for the synthesis of PbS quantum dots (QDs) using thiourea and lead acetate as sources of sulfur and lead, respectively. The sizes of the PbS QDs could be systematically controlled by simply adjusting the reaction parameters. Cd post-treatment via a cation exchange method was performed to increase the stability of QDs. As a proof of concept, colloidal PbS QDs synthesized by using air-stable thiourea were employed as light harvesters for both (i) solar driven photoelectrochemical (PEC) hydrogen generation and (ii) QDs sensitized solar cells (QDSSCs). For PEC hydrogen generation, similar saturated photocurrent densities are observed by using thiourea compared to bis(trimethylsilyl) sulfide, which is air-sensitive and unstable. For QDSSCs, the devices fabricated with QDs synthesized from thiourea reveal a better performance compared to devices fabricated with QDs synthesized from traditional bis(trimethylsilyl) sulfide. Our work demonstrates that this synthetic method is a promising alternative to the existing methodologies of PbS QDs and holds great potential for future solar technologies.

Effects on the Thermo-Mechanical and Crystallinity Properties of Nylon 6,6 Electrospun Fibres Reinforced with One Dimensional (1D) and Two Dimensional (2D) Carbon.

Electrospun one dimensional (1D) and two dimensional (2D) carbon based polymer nanocomposites are studied in order to determine the effect provided by the two differently structured nanofillers on crystallinity and thermo-mechanical properties of the nanofibres. The nanomaterials studied are pristine carbon nanotubes, oxidised carbon nanotubes, reduced graphene oxide and graphene oxide. Functional groups associated with the order structure of the polymers are analysed by infrared and Raman spectroscopies; the morphology is studied by scanning electron microscopy and the crystallinity properties are investigated by differential scanning calorimetry and X-ray diffraction. Differences in crystallisation behaviour between 1D and 2D carbon based nanofibres are shown by their crystallinity degree and their crystal sizes. The nanocomposite crystal sizes perpendicular to the plane (100) decrease with nanofiller content in all cases. The crystallinity trend and crystal sizes are in accordance with storage modulus response. The results also suggest that functionalisation favours interfacial bonding and dispersion of the nanomaterials within the polymer matrix. As a consequence the number of nucleating sites increases which in turn decreases the crystal size in the nanocomposites. These features explain the improved thermo-mechanical properties in the nanocomposites.