Electrical detection of spin transport in Si two-dimensional electron gas systems.

Spin transport in a semiconductor-based two-dimensional electron gas (2DEG) system has been attractive in spintronics for more than ten years. The inherent advantages of high-mobility channel and enhanced spin-orbital interaction promise a long spin diffusion length and efficient spin manipulation, which are essential for the application of spintronics devices. However, the difficulty of making high-quality ferromagnetic (FM) contacts to the buried 2DEG channel in the heterostructure systems limits the potential developments in functional devices. In this paper, we experimentally demonstrate electrical detection of spin transport in a high-mobility 2DEG system using FM Mn-germanosilicide (Mn(Si0.7Ge0.3)x) end contacts, which is the first report of spin injection and detection in a 2DEG confined in a Si/SiGe modulation doped quantum well structure (MODQW). The extracted spin diffusion length and lifetime are l sf = 4.5 µm and [Formula: see text] at 1.9 K respectively. Our results provide a promising approach for spin injection into 2DEG system in the Si-based MODQW, which may lead to innovative spintronic applications such as spin-based transistor, logic, and memory devices.

Electrically pumped lasing from Ge Fabry-Perot resonators on Si.

Room temperature lasing from electrically pumped n-type doped Ge edge emitting devices has been observed. The edge emitter is formed by cleaving Si-Ge waveguide heterodiodes, providing optical feedback through a Fabry-Perot resonator. The electroluminescence spectra of the devices showed optical bleaching and intensity gain for wavelengths between 1660 nm and 1700 nm. This fits the theoretically predicted behavior for the n-type Ge material system. With further pulsed electrical injection of 500 kA/cm2 it was possible to reach the lasing threshold for such edge emitters. Different lengths and widths of devices have been investigated in order to maintain best gain-absorption ratios.

Electroluminescence of GeSn/Ge MQW LEDs on Si substrate.

Multi-quantum well light-emitting diodes, consisting of ten alternating GeSn/Ge-layers, were grown by molecular beam epitaxy on Si. The Ge barriers were 10 nm thick, and the GeSn wells were grown with 7% Sn and thicknesses between 6 and 12 nm. The electroluminescence spectra measured at 300 and 80 K yield a broad and intensive luminescence band. Deconvolution revealed three major lines produced by the GeSn wells that can be interpreted in terms of quantum confinement. We interpret that the three lines represent two direct lines, formed by transitions with the light and heavy hole band, respectively, and an indirect line. Biaxial compressive strain causes a splitting of light and heavy holes in the GeSn wells. This interpretation is supported by an effective mass band structure calculation.

GeSn-on-Si normal incidence photodetectors with bandwidths more than 40 GHz.

GeSn (Sn content up to 4.2%) photodiodes with vertical pin structures were grown on thin Ge virtual substrates on Si by a low temperature (160 °C) molecular beam epitaxy. Vertical detectors were fabricated by a double mesa process with mesa radii between 5 µm and 80 µm. The nominal intrinsic absorber contains carrier densities from below 1 · 10(16) cm(-3) to 1 · 10(17) cm(-3) for Ge reference detectors and GeSn detectors with 4.2% Sn, respectively. The photodetectors were investigated with electrical and optoelectrical methods from direct current up to high frequencies (40 GHz). For a laser wavelength of 1550 nm an increasing of the optical responsivities (84 mA/W -218 mA/W) for vertical incidence detectors with thin (300 nm) absorbers as function of the Sn content were found. Most important from an application perspective all detectors had bandwidth above 40 GHz at enough reverse voltage which increased from zero to -5 V within the given Sn range. Increasing carrier densities (up to 1 · 10(17) cm(-3)) with Sn contents caused the depletion of the nominal intrinsic absorber at increasing reverse voltages.

Direct bandgap narrowing in Ge LED's on Si substrates.

In this paper we investigate the influence of n-type doping in Ge light emitting diodes on Si substrates on the room temperature emission spectrum. The layer structures are grown with a special low temperature molecular beam epitaxy process resulting in a slight tensile strain of 0.13%. The Ge LED's show a dominant direct bandgap emission with shrinking bandgap at the Γ point in dependence of n-type doping level. The emission shift (38 meV at 10²°cm⁻³) is mainly assigned to bandgap narrowing at high doping. The electroluminescence intensity increases with doping concentrations up to 3x10¹9cm⁻³ and decreases sharply at higher doping levels. The integrated direct gap emission intensity increases superlinear with electrical current density. Power exponents vary from about 2 at low doping densities up to 3.6 at 10²°cm⁻³ doping density.

Quantifying thermal transport in buried semiconductor nanostructures via cross-sectional scanning thermal microscopy.

Managing thermal transport in nanostructures became a major challenge in the development of active microelectronic, optoelectronic and thermoelectric devices, stalling the famous Moore's law of clock speed increase of microprocessors for more than a decade. To find the solution to this and linked problems, one needs to quantify the ability of these nanostructures to conduct heat with adequate precision, nanoscale resolution, and, essentially, for the internal layers buried in the 3D structure of modern semiconductor devices. Existing thermoreflectance measurements and "hot wire" 3ω methods cannot be effectively used at lateral dimensions of a layer below a micrometre; moreover, they are sensitive mainly to the surface layers of a relatively high thickness of above 100 nm. Scanning thermal microscopy (SThM), while providing the required lateral resolution, provides mainly qualitative data of the layer conductance due to undefined tip-surface and interlayer contact resistances. In this study, we used cross-sectional SThM (xSThM), a new method combining scanning probe microscopy compatible Ar-ion beam exit nano-cross-sectioning (BEXP) and SThM, to quantify thermal conductance in complex multilayer nanostructures and to measure local thermal conductivity of oxide and semiconductor materials, such as SiO2, SiGex and GeSny. By using the new method that provides 10 nm thickness and few tens of nm lateral resolution, we pinpoint crystalline defects in SiGe/GeSn optoelectronic materials by measuring nanoscale thermal transport and quantifying thermal conductivity and interfacial thermal resistance in thin spin-on materials used in extreme ultraviolet lithography (eUV) fabrication processing. The new capability of xSThM demonstrated here for the first time is poised to provide vital insights into thermal transport in advanced nanoscale materials and devices.

Weak localization and weak antilocalization in doped Ge1-y Sn y layers with up to 8% Sn.

Low-temperature magnetoresistance measurements of n- and p-doped germanium-tin (Ge1-y Sn y ) layers with Sn concentrations up to 8% show contributions arising from effects of weak localization for n-type and weak antilocalization for p-type doped samples independent of the Sn concentration. Calculations of the magnetoresistance using the Hikami-Larkin-Nagaoka model for two-dimensional transport allow us to extract the phase-coherence length for all samples as well as the spin-orbit length for the p-type doped samples. For pure Ge, we find phase-coherence lengths as long as (349.0 ± 1.4) nm and (614.0 ± 0.9) nm for n-type and p-type doped samples, respectively. The phase-coherence length decreases with increasing Sn concentration. From the spin-orbit scattering length, we determine the spin-diffusion scattering length in the range of 20-30 nm for all highly degenerate p-type doped samples irrespective of Sn concentration. These results show that Ge1-y Sn y is a promising material for future spintronic applications.

Identification and pattern of perfluorooctane sulfonate (PFOS) isomers in human serum and plasma.

Human serum and plasma from Sweden (n=17), the United Kingdom (the UK) (n=13) and Australia (n=40) were analyzed by high performance liquid chromatography coupled to mass spectrometry. The objective was to identify different perfluorooctane sulfonate (PFOS) isomers. Similar isomer patterns typical for the electrochemical fluorination (ECF) process were found for all samples. The linear PFOS (L-PFOS) was the major isomer found (58-70%) followed by the monosubstituted PFOS isomers 1/6-CF(3)-PFOS (18-22%) and 3/4/5-CF(3)-PFOS (13-18%). Disubstituted isomers were also detected. The percentage of L-PFOS found in the serum and plasma samples was lower compared to a standard PFOS product (76-79%). The pattern of PFOS isomers in human serum and plasma may be suggestive concerning potential isomeric discrimination since PFOS is only produced by ECF. Possibilities for such isomer discrimination are discussed. Significant higher content of L-PFOS (68%) in Swedish samples compared to Australia and the UK (59%) was also found, which may suggest differences in exposure sources for humans.

Short- and medium-chain chlorinated paraffins in biota from the European Arctic -- differences in homologue group patterns.

Congener and homologue group patterns of chlorinated paraffins (CPs) in biota can be influenced by different processes, but these are not well studied yet. Short- (SCCPs) and medium-chain chlorinated paraffins (MCCPs) were quantified in liver from Arctic char and seabirds (little auk and kittiwake) collected at Bear Island (European Arctic) as well as in cod from Iceland and Norway. CP concentrations were between 5 and 88 ng/g wet weight (ww) for SCCPs and between 5 and 55 ng/g ww for MCCPs with one exception of 370 ng/g measured in a liver sample from little auk. The SCCP homologue group patterns were compared with those of technical mixtures and of SCCPs present in cod liver from the Baltic Sea. The latter showed a more common SCCP homologue distribution (sum of C(11) and C(12)>60%) in contrast to cod liver from the Northwest of Europe, which had a high abundance of C(10) and C(12) congeners. Seabirds from Bear Island contained an equally distributed SCCP homologue group pattern. In Arctic char, the SCCP distribution was closer to technical products, but with a high proportion (average of 18.9%) of C(10) congeners. A comparison of C(10)/C(12) ratios confirmed the higher abundance of C(10) congeners in samples from higher latitudes. For the first time, MCCPs could be detected in Arctic samples. The average proportion of C(14) congeners was 65.8%. The C(14)/C(15) abundance ratio was similar to technical mixtures. High-chlorinated CPs (Cl(>7)) were also detectable. The average chlorine content of the SCCPs was 61.9% (59.0-63.3%), and that of the MCCPs 55.8% (54.5-57.4%).

Congener group patterns of chloroparaffins in marine sediments obtained by chloride attachment chemical ionization and electron capture negative ionization.

Congener group patterns of technical short chain and medium chain chloroparaffins (SCCP and MCCP) were determined by electron capture negative ionization (ECNI) and chloride attachment chemical ionization (CACI) mass spectrometry (MS). In contrast to CACI-MS, congener patterns obtained by ECNI showed always a shift to the next higher chlorinated congener and carbon chain length group. Consequently, the calculated molecular masses and chlorine contents were higher for ECNI (factor 1.10+/-0.03 and 1.09+/-0.03, respectively). ECNI/CACI ratios in sediment samples from the North and Baltic Sea were also slightly higher. However, a more pronounced shift of the congener pattern for a given carbon chain length to congeners with 2-3 more chlorine atoms was observed. SCCP and MCCP concentrations obtained by ECNI-MS were in the range of 8-63ngg(-1) (North Sea) and 22-149ngg(-1) dry weight (Baltic Sea). MCCP levels were highest in all samples (MCCP/SCCP factor 1.1-3.2).

New quantification procedure for the analysis of chlorinated paraffins using electron capture negative ionization mass spectrometry.

An improved quantification procedure for the analysis of chlorinated paraffins (CPs) is presented based on electron capture negative ionization mass spectrometry. It compensates differences in response factors between reference CP mixtures and the CP pattern present in environmental samples. The use of a CP standard with a matching degree of chlorination is no longer necessary. It could be shown that the response factors of C10-, C11-, C12- and C13-CP mixtures of both 50 and 60% chlorine content were only slightly influenced by the carbon chain length. A linear correlation (R2 = 0.965) between the total response factor of a CP mixture and its chlorine content was obtained for seven short chain chlorinated paraffin mixtures (SCCP, C10-C13) with different composition and chlorine content (51-69%). Maximum single deviations were <7% for this reference set. It allowed to determine the correct total response factor of the CP composition present in a sample. The deviations were not more than 7-33% for five independent SCCP control samples compared to up to 373% for the conventional procedure. The procedure was tested by quantifying the SCCP and MCCP levels in 10 fish liver samples. The proposed method allowed to compensate the influence of the degree of chlorination of the applied reference standard on the total response factor.

Evaluation of four mass spectrometric methods for the gas chromatographic analysis of polychlorinated n-alkanes.

The suitability of four mass spectrometric methods for the gas chromatographic analysis of polychlorinated n-alkanes (PCAs, also called chlorinated paraffins) was evaluated and compared using spiked and fish liver samples. Electron ionization tandem mass spectrometry (EI-MS/MS) as well as electron capture negative ionization (ECNI) combined with low and high resolution mass spectrometry and CH4/CH2Cl2-negative ion chemical ionization (NICI) low resolution mass spectrometry were investigated. All methods showed an accuracy of <21% for the analysis of spiked fish samples. However, the analysis of real samples showed deviations of up to 46% between the four mass spectrometric methods. The influence of the selected reference standard on quantification was also evaluated. The use of a quantification standard with a degree of chlorination deviating from that of the sample can result in differences of > 100% for the ECNI methods. EI-MS/MS and CH4/CH2Cl2-NICI led to errors of maximum 17% and 33%, respectively, independent from the degree of chlorination of the used reference standard.

First study of congener group patterns and concentrations of short- and medium-chain chlorinated paraffins in fish from the North and Baltic Sea.

This study presents the first investigation of concentrations and congener group patterns of short- (SCCPs) and medium-chain chlorinated paraffins (MCCPs) in fish from the North and Baltic Sea. North Sea dab, cod and flounder were studied. High resolution gas chromatography (HRGC) coupled to low resolution mass spectrometry (LRMS) in the electron capture negative ionization mode (ECNI) was employed. Good linearity (R2>0.993, 7 measuring points) was achieved between 1 and 100 ng/g of CP mixtures for SCCPs and MCCPs. The limits of detection were 0.5-1 ng/microl of CP mixture for the major congener groups of SCCPs and MCCPs. A clean-up comprising fat extraction, adsorption chromatography on silicagel impregnated with concentrated sulphuric acid and adsorption chromatography on Florisil was employed to avoid interferences from other polychlorinated compounds. Recoveries of CPs in spiked samples ranged between 80% and 100%. Accuracy was controlled with spiked samples and deviated not more than 10% from the expected values. Quantification was performed with standards of an average chlorine content as close as possible to that of the samples (SCCPs: 59-62%, MCCPs: 53-58%). SCCP concentrations ranged between 19 and 286 ng/g liver wet weight (ww), MCCP concentrations were comparable with a range of 25-260 ng/gww. Congener group patterns were also determined and discussed. In samples from the Baltic Sea the SCCP congener pattern was similar to that of commercial SCCP mixtures or C13 congeners were most abundant. In samples from the North Sea a higher relative abundance of C10 congeners was observed.

Performance and reliability of splitless microliter gradient pumps in a metabolic stability study using cytochrome P450/3A4 and capillary liquid chromatography-mass spectrometry.

The performance of two commercially available capillary LC pumps (MicroPro (Eldex, USA), Evolution 200 (ProLab, Switzerland)) generating really splitless gradients in the microliter per minute range was tested in detail concerning their applicability for routine drug discovery. A standard method to study metabolic stability against CYP450 isoform 3A4 was selected. This method was transformed into a fast splitless capillary LC-MS method. Both pumps generated reproducible gradients at flows of 5-10 microl/min within 10-15 min. Although gradient formation of the MicroPro system was very reproducible, its equilibration time was too long for fast gradients around 5 microl/min. The Evolution 200 pump offered a good performance with 180 microm i.d. columns at a flow rate of 6 microl/min. The precision of the retention time of the internal standard (ISTD) varied between 1.4 and 3.4% (n = 131-152, three different columns tested). Up to 800 injections of sufficient performance on one column and a stable enough response of the ISTD for 16 h sequence duration were obtained. Accuracy between 95 and 105% and precision < or = 8.4% for 1'-hydroxylated midozolam were reached. The IC50 values of the miniaturized assay (drug candidate BAL4815 1.7 +/- 0.5, itraconazole 0.46 +/- 0.06, and ketoconazole 0.12 +/- 0.01 microM) agreed well with those of the conventional approach. Details concerning method optimization and limitations in operation are discussed in detail. Still, the overall performance of the capillary LC pumps cannot cope completely with that of conventional HPLC pumps in terms of user-friendliness.

Comparison of three types of mass spectrometers for HPLC/MS analysis of perfluoroalkylated substances and fluorotelomer alcohols.

The performance of three different types of mass spectrometers (MS) coupled to high performance liquid chromatography (HPLC) was compared for trace analysis of perfluoroalkylated substances (PFAS) and fluorotelomer alcohols (FTOHs). Ion trap MS in the full scan and product ion MS2 mode, time-of-flight (TOF) high resolution MS and quadrupole MS in the selected ion mode as well as triple quadrupole tandem MS were tested. Electrospray ionisation in the negative ion mode [ESI-] was best suited for all instruments and compounds. PFAS could only be separated by a buffered mobile phase, but the presence of buffer suppressed the ionisation of FTOHs. Therefore, two independent chromatographic methods were developed for the two compound classes. Mass spectra and product ion spectra obtained by in-source and collision induced dissociation fragmentation are discussed including ion adduct formation. Product ion yields of PFAS were only in the range of 0.3 to 12%, independent from the applied MS instrument. Ion trap MS2 gave product ion yields of 20 to 62% for FTOHs, whereas only 4.1 to 5.8% were obtained by triple quadrupole tandem MS. Ion trap MS was best suited for qualitative analysis and structure elucidation of branched isomeric structures of PFAS. Providing typical detection limits of 5 ng injected in MS2 mode, it was not sensitive enough for selective trace amount quantification. TOF high resolution MS was the only technique combining high selectivity and excellent sensitivity for PFAS analysis (detection limits of 2 to 10 pg), but lacked the possibility of MS-MS. Triple quadrupole tandem MS was the method of choice for quantification of FTOHs with detection limits in the low pg range. It is also well suited for the determination of PFAS, though its detection limits of 10 to 100 pg in tandem MS mode are about one order of magnitude higher than for TOF MS.

Development of a comprehensive analytical method for the determination of chlorinated paraffins in spruce needles applied in passive air sampling.

Conifer needles are used for the monitoring of atmospheric persistent organic pollutants. The objective of the present study was to develop a method for the detection of airborne chlorinated paraffins (CPs) using spruce needles as a passive sampler. The method is based on liquid extraction of the cuticular wax layer followed by chromatographic fractionation and detection of CPs using two different GCMS techniques. Total CP concentrations (sum of short (SCCP), medium (MCCP) and long chain CPs (LCCP)) were determined by EI-MS/MS. SCCP and MCCP levels as well as congener group patterns (n-alkane chain length, chlorine content) could be evaluated using ECNI-LRMS. For the first time, data on environmental airborne CPs on spruce needles taken within the Monitoring Network in the Alpine Region for Persistent and other Organic Pollutants (MONARPOP) are presented providing evidence that spruce needles are a suitable passive sampling system for the monitoring of atmospheric CPs.

Altitude profiles of total chlorinated paraffins in humus and spruce needles from the Alps (MONARPOP).

Chlorinated paraffins (CPs) are toxic, bioaccumulative, persistent, and ubiquitously present in the environment. CPs were analyzed in humus and needle samples, which were taken within the Monitoring Network in the Alpine Region for Persistent and other Organic Pollutants (MONARPOP) at sampling sites of 7 different altitude profiles in the Alps. Gas chromatography combined with electron ionization tandem mass spectrometry (EI-MS/MS) was used for the determination of total CPs (sum of short, medium and long chain CPs). CPs were found in all samples; the concentrations varied between 7 and 199 ng g(-1) dry weight (dw) and within 26 and 460 ng g(-1) dw in humus and needle samples, respectively. A clear vertical tendency within the individual altitude profiles could not be ascertained. Within all altitude profiles, elevated concentrations were observed in humus samples taken between 700 and 900 m and between 1300 and 1500 m. In the needle samples no similar correlation could be observed due to higher variation of the data.

Historical profiles of chlorinated paraffins and polychlorinated biphenyls in a dated sediment core from Lake Thun (Switzerland).

A dated sediment core from Lake Thun covering the last 120 years was analyzed to get an overview of the historical trend of the chlorinated paraffin (CP) and polychlorinated biphenyl (PCB) deposition, because CPs and PCBs have/had similar applications as plasticizers and flame retardants. Total CP concentrations (sum of short chain (SCCP), medium chain (MCCP), and long chain CPs (LCCP)) showed a steep increase in the 1980s and a more-or-less stable level of 50 ng g(-1) dry weight (dw) since then. The concentration-time profile is in good agreement with the available information on global production data. The quantification of higher chlorinated SCCPs using electron capture negative ionization low resolution mass spectrometry (ECNI-LRMS) revealed an increase in recent years. In addition, the degree of chlorination of SCCPs has strongly increased during the past 40 years, which may indicate its use as an additive for plastics, paints, and coatings. Furthermore, PCBs were analyzed in dated sediment slices. The PCB concentrations (sum of the six indicator congeners) peaked around 1969 (18 ng g(-1) dw) and decreased to 1.3 ng g(-1) dw in the surface layer corresponding to 2004. The peak level of CPs exceeded those of PCBs by about a factor of 3.

Mass spectral studies of perfluorooctane sulfonate derivatives separated by high-resolution gas chromatography.

The mass spectral characteristics of perfluorooctane sulfonate (PFOS, C(8)F(17)SO(3)-) isomers present in technical PFOS were obtained using high-resolution gas chromatography (HRGC) combined with mass spectrometry (MS). To make PFOS amenable to HRGC separation, a simple derivatization procedure was developed. The method involved the conversion of PFOS into the iso-propyl ester using iso-propanol as the derivatization reagent under acidic conditions. Mass spectra were generated employing electron ionization (EI) and negative chemical ionization (NCI). Interpretation of fragment ions was possible due to the use of deuterium-labeled iso-propanol as derivatization reagent, which induced mass shifts in the electron ionization (EI) and negative chemical ionization (NCI) mass spectra. HRMS allowed the accurate mass measurement of important EI fragments and confirmed the derivatization reaction as well as the proposed fragmentation pathway involving rearrangement. Moreover, the high resolution provided by HRGC enabled the separation of eleven PFOS isomers present in the technical product. This is an improvement over the previously reported high-performance liquid chromatography (HPLC) separation. A complete identification of all isomers was not possible due to lack of pure reference materials. Finally, the developed derivatization procedure was successfully applied to perfluoroalkyl carboxylates (PFCA) and corresponding fragmentation involving rearrangement of the derivatized PFCA was observed. The described qualitative derivatization offers a promising alternative technique for the separation and identification of isomers of perfluoroalkyl sulfonates and carboxylates by HRGC/MS.