Cervical spine injuries and flexibilities following axial impact with lateral eccentricity.

PURPOSE: Determine the effects of dynamic injurious axial compression applied at various lateral eccentricities (lateral distance to the centre of the spine) on mechanical flexibilities and structural injury patterns of the cervical spine. METHODS: 13 three-vertebra human cadaver cervical spine specimens (6 C3-5, 3 C4-6, 2 C5-7, 2 C6-T1) were subjected to pure moment flexibility tests (±1.5 Nm) before and after impact trauma was applied in two groups: low and high lateral eccentricity (1 and 150 % of the lateral diameter of the vertebral body, respectively). Relative range of motion (ROM) and relative neutral zone (NZ) were calculated as the ratio of post and pre-trauma values. Injuries were diagnosed by a spine surgeon and scored. Classification functions were developed using discriminant analysis. RESULTS: Low and high eccentric loading resulted in primarily bony fractures and soft tissue injuries, respectively. Axial impacts with high lateral eccentricities resulted in greater spinal motion in lateral bending [median relative ROM 3.5 (interquartile range, IQR 2.3) vs. 1.4 (IQR 0.5) and median relative NZ 4.7 (IQR 3.7) vs. 2.3 (IQR 1.1)] and in axial rotation [median relative ROM 5.3 (IQR 13.7) vs. 1.3 (IQR 0.5), p < 0.05 for all comparisons] than those that resulted from low eccentricity impacts. The developed classification functions had 92 % classification accuracy. CONCLUSIONS: Dynamic axial compression loading of the cervical spine with high lateral eccentricities produced primarily soft tissue injuries resulting in more post-injury spinal flexibility in lateral bending and axial rotation than that associated with the bony fractures resulting from low eccentricity impacts.

A history of spine biomechanics. Focus on 20th century progress.

The application of mechanical principles to problems of the spine dates to antiquity. Significant developments related to spinal anatomy and biomechanical behaviour made by Renaissance and post-Renaissance scholars through the end of the 19th century laid a strong foundation for the developments since that time. The objective of this article is to provide a historical overview of spine biomechanics with a focus on the developments in the 20th century. The topics of spine loading, spinal posture and stability, spinal kinematics, spinal injury, and surgical strategies were reviewed.

Design and biomechanical evaluation of a rodent spinal fixation device.

STUDY DESIGN: An in vitro and in vivo study in rats. OBJECTIVES: To design a novel rat spinal fixation device and investigate its biomechanical effectiveness in stabilizing the spine up to 8 weeks post injury. METHODS: A fixation device made of polyetheretherketone was designed to stabilize the spine via bilateral clamping pieces. The device effectiveness was assessed in a Sprague-Dawley rat model after it was applied to a spine with a fracture-dislocation injury produced at C5-C6. Animals were euthanized either immediately (n=6) or 8 weeks (n=9) post-injury and the C3-T1 segment of the cervical spine was removed for biomechanical evaluation. Segments of intact spinal columns (C3-T1) (n=6) served as uninjured controls. In these tests, anterior-posterior shear forces were applied to the C3 vertebra to produce flexion and extension bending moments at the injury site (peak 12.8 Nmm). The resultant two-dimensional motions at the injury site (that is, C5-C6) were measured using digital imaging and reported as ranges of motion (ROM) or neutral zones (NZ). RESULTS: Flexion/extension ROMs (average±s.d.) were 18.1±3.3°, 19.9±7.5° and 1.5±0.7°, respectively for the intact, injured/fixed, and injured/8-week groups, with the differences being highly significant for the injured/8-week group (P=0.0002). Flexion/extension NZs were 3.4±2.8°, 5.0±2.4°, and 0.7±0.5°, respectively for the intact, injured/fixed, and injured/8-week groups, with the differences being significant for the injured/8-week group (P=0.04). CONCLUSION: The device acutely stabilizes the spine and promotes fusion at the site of injury.

Strength indices from pQCT imaging predict up to 85% of variance in bone failure properties at tibial epiphysis and diaphysis.

Our primary objective was to validate the Bone Strength Index for compression (BSIC) by determining the amount of variance in failure load and stiffness that was explained by BSIC and bone properties at two distal sites in human cadaveric tibiae when tested in axial compression. Our secondary objective was to assess the variance in failure moment and flexural rigidity that was explained by bone properties, geometry and strength indices in the tibial diaphysis when tested in 4-point bending. Twenty cadaver tibiae pairs from 5 female and 5 male donors (mean age 74 yrs, SD 6 yrs) were measured at the distal epiphysis (4 and 10% sites of the tibial length from the distal end) and diaphysis (50 and 66% sites) by peripheral Quantitative Computed Tomography (pQCT; XCT 2000, Stratec). After imaging, we conducted axial compression tests on the distal tibia and 4-point bending tests on the diaphysis. Total bone mineral content and BSIC (product of total area and squared density of the cross-section) at the 4% site predicted 75% and 85% of the variance in the failure load and 52% and 57% in stiffness, respectively. At the diaphyseal sites 80% or more of the variance in failure moment and/or flexural rigidity was predicted by total and cortical area and content, geometry and strength indices corresponding to the axes of bending.

Can extra-articular strains be used to measure facet contact forces in the lumbar spine? An in-vitro biomechanical study.

Experimental measurement of the load-bearing patterns of the facet joints in the lumbar spine remains a challenge, thereby limiting the assessment of facet joint function under various surgical conditions and the validation of computational models. The extra-articular strain (EAS) technique, a non-invasive measurement of the contact load, has been used for unilateral facet joints but does not incorporate strain coupling, i.e. ipsilateral EASs due to forces on the contralateral facet joint. The objectives of the present study were to establish a bilateral model for facet contact force measurement using the EAS technique and to determine its effectiveness in measuring these facet joint contact forces during three-dimensional flexibility tests in the lumbar spine. Specific goals were to assess the accuracy and repeatability of the technique and to assess the effect of soft-tissue artefacts. In the accuracy and repeatability tests, ten uniaxial strain gauges were bonded to the external surface of the inferior facets of L3 of ten fresh lumbar spine specimens. Two pressure-sensitive sensors (Tekscan) were inserted into the joints after the capsules were cut. Facet contact forces were measured with the EAS and Tekscan techniques for each specimen in flexion, extension, axial rotation, and lateral bending under a +/- 7.5 N m pure moment. Four of the ten specimens were tested five times in axial rotation and extension for repeatability. These same specimens were disarticulated and known forces were applied across the facet joint using a manual probe (direct accuracy) and a materials-testing system (disarticulated accuracy). In soft-tissue artefact tests, a separate set of six lumbar spine specimens was used to document the virtual facet joint contact forces during a flexibility test following removal of the superior facet processes. Linear strain coupling was observed in all specimens. The average peak facet joint contact forces during flexibility testing was greatest in axial rotation (71 +/- 25 N), followed by extension (27 +/- 35 N) and lateral bending (25 +/- 28 N), and they were most repeatable in axial rotation (coefficient of variation, 5 per cent). The EAS accuracy was about 20 per cent in the direct accuracy assessment and about 30 per cent in the disarticulated accuracy test. The latter was very similar to the Tekscan accuracy in the same test. Virtual facet loads (r.m.s.) were small in axial rotation (12 N) and lateral bending (20 N), but relatively large in flexion (34 N) and extension (35 N). The results suggested that the bilateral EAS model could be used to determine the facet joint contact forces in axial rotation but may result in considerable error in flexion, extension, and lateral bending.

Ipsilateral shoulder and elbow replacements: on the risk of periprosthetic fracture.

BACKGROUND: Ipsilateral shoulder and elbow replacements may leave only a short segment of bone bridging the two implants in the humerus. The potential for high stress concentrations as a result of this geometry has been a concern with regard to periprosthetic fracture, especially with osteoporotic bone. The study aims to determine the optimum length of the bone-bridge between shoulder and elbow humeral implants, and to assess the effect of filling the canal with cement. METHODS: A three-dimensional finite element model was used to compare the stresses between a humerus with a solitary prosthesis and a humerus with both proximal and distal cemented prostheses. The length of the bone-bridge and the effect of filling the canal with cement were studied under bending and torsion. FINDINGS: Gradual load transfer from prosthesis to bone was observed for all cases, and no stress concentration was evident. The length of the bone-bridge had no deleterious effect on stresses in the humerus, and filling the canal with cement did not appreciably decrease the loads carried by the humerus. INTERPRETATION: The length of the bone-bridge between stem tips has little effect on the resultant stresses in the humerus. Filling the canal with cement adds little benefit to the structural integrity of the humerus. Ipsilateral shoulder and elbow prostheses may be considered independent of one another in terms of risk of periprosthetic fracture.

Stress relaxation of the respiratory system in developing piglets.

To characterize the effect of postnatal development on the viscoelastic behavior of the respiratory system, we quantified the amplitude and time course of stress relaxation in the lungs and chest wall of seven newborn and eight 8-wk-old anesthetized piglets. Stress relaxation was distinguished from other dissipative pressure losses by performing airway occlusions at various constant inspiratory flows and fitting the pressure decays that ensue during the occlusions to a double-exponential function. We found that the amplitude of stress relaxation related linearly to the increase in elastic recoil (and, by extension, in the volume) of the lungs, chest wall, and respiratory system during the inflations preceding the occlusions. On the average, the slope of this relationship was 38-44% lower in the 8-wk-old than in the newborn piglets for the lungs and was not different for the chest wall. The time course of stress relaxation, expressed as a time constant, was not influenced by age. Our results indicate that respiratory system viscoelasticity is sensitive to the geometric and structural changes experienced by the lungs during the period of rapid somatic growth that follow birth in most mammals.

Three-dimensional mechanical properties of the thoracolumbar junction.

The thoracolumbar junction region is a frequent site of spinal trauma. Accurate knowledge of the normal mechanical behavior of the intervertebral joints in this region is of importance to the clinician in treating the spinal injuries. The present study documented the complete three-dimensional motions of levels T11-T12 and T12-L1 in the thoracolumbar region. Pure moments of flexion/extension, bilateral axial torque, and bilateral lateral bending were applied to 11 three-vertebrae human cadaveric specimens (T11-L1) to a maximum of 7.5 Nm. Intervertebral motions were calculated using stereophotogrammetry and presented in the form of load-displacement curves, each containing three rotations and three translations at one intervertebral level. Average +/- SD flexion, extension, axial rotation, and lateral bending ranges of motion to one side were 2.7 +/- 1.3 degrees, 2.4 +/- 1.3 degrees, 1.8 +/- 0.7 degrees, and 3.5 +/- 1.1 degrees, respectively, at level T11-T12. The same ranges of motion at T12-L1 were 2.9 +/- 1.4 degrees, 3.9 +/- 1.4 degrees, 1.2 +/- 0.7 degrees, and 3.7 +/- 1.1 degrees, respectively. The extension and axial rotation ranges of motion at level T11-T12 were found to be significantly different than the same motions at T12-L1. The different geometry in the facet joints explains these observed differences in the mechanical behavior of T11-T12 and T12-L1.

Subfailure injury of the rabbit anterior cruciate ligament.

Ligamentous injuries range in severity from a simple sprain to a complete rupture. Although sprains occur more frequently than complete failures, only a few studies have investigated the phenomena of these subfailure injuries. The purpose of our study was to document the changes in the load-deformation curve until the failure point, after the ligament has been subjected to an 80% subfailure stretch. Thirteen paired fresh rabbit bone-anterior cruciate ligament-bone preparations were used. One of the pairs (control) was stretched until failure; the other (experimental) was first stretched to 80% of the failure deformation of the control and then stretched to failure. Comparisons were made between the load-deformation curves of the experimental and control specimens. The nonlinear load-deformation curves were characterized by eight parameters: failure load (Ffail), failure deformation (Dfail), energy until failure (Efail), deformations measured at 5, 10, 25, and 50% of the failure load (D5, D10, D25, and D50, respectively), and stiffness measured at 50% of the failure force (K50). There were no significant differences in the values for Ffail, Dfail, and Efail between the experimental and control ligaments (p > 0.33). In contrast, the deformation values were all larger for the experimental than the control ligaments (p > 0.01). The deformations D5, D10, D25, and D50 (mean +/- SD) for the control were 0.36 +/- 0.13, 0.49 +/- 0.23, 0.81 +/- 0.35, and 1.23 +/- 0.41 mm. The corresponding deformations for the experimental ligaments were, respectively, 209, 186, 153, and 130% of the control values. K50 was also greater for the experimental ligament (125.0 +/- 41.7 N/mm compared with 108.7 +/- 31.4 N/mm, p < 0.03). These findings indicate that even though the strength of the ligament did not change due to a subfailure injury, the shape of the load-displacement curve, especially at low loads, was significantly altered. Under the dynamic in vivo loading conditions of daily living, this may result in increased joint laxity, additional loads being applied to other joint structures, and, with time, to joint problems.

An anatomic basis for spinal instability: a porcine trauma model.

To determine the anatomic basis for spinal instabilities, 16 porcine cervical spine specimens were subjected to a well-defined sagittal plane trauma. The multidirectional instability of each specimen was measured before and after trauma. Detailed anatomic dissections were performed on each traumatized specimen to quantitate the extent of injury to several distinct anatomic structures and columns. Multiple regression models were constructed to determine which anatomic structures and columns correlated best with each multidirectional instability. Flexion instability correlated best with injury to the interspinous/supraspinous ligaments and the ligamentum flavum. Extension instability correlated best with anterior longitudinal ligament and pedicle injury. Axial rotation instability correlated best with anterior disc-end-plate and capsular ligament injuries, while lateral bending instability correlated best with posterior disc-end-plate injuries. Anterior column injuries correlated best with extension, axial rotation, and lateral bending instabilities, while posterior column injuries correlated best with flexion instability. Finally, individual anatomic structural injuries had higher correlations with multidirectional instabilities than did the injuries defined by the anatomic columns.

Mechanical behavior of the human lumbar and lumbosacral spine as shown by three-dimensional load-displacement curves.

The lumbar region is a frequent site of spinal disorders, including low-back pain, and of spinal trauma. Clinical studies have established that abnormal intervertebral motions occur in some patients who have low-back pain. A knowledge of normal spinal movements, with all of the inherent complexities, is needed as a baseline. The present study documents the complete three-dimensional elastic physical properties of each lumbar intervertebral level from the level between the first and second lumbar vertebrae through the level between the fifth lumbar and first sacral vertebrae. Nine whole fresh-frozen human cadaveric lumbar-spine specimens were used. Pure moments of flexion-extension, bilateral axial torque, and bilateral lateral bending were applied, and three-dimensional intervertebral motions were determined with use of stereophotogrammetry. The motions were presented in the form of a set of six load-displacement curves, quantitating intervertebral rotations and translations. The curves were found to be non-linear, and the motions were coupled. The ranges of motion were found to compare favorably with reported values from in vivo studies.

A comparative biomechanical investigation of anterior lumbar interbody cages: central and bilateral approaches.

BACKGROUND: Some biomechanical studies have been performed to evaluate the stabilization provided by interbody cages, but there are virtually no comparative data for the different designs. Furthermore, most investigators have used animal models, which may have led to different results due to morphological variation in the end plates and articular facets. The objectives of the current study were to evaluate whether two different anterior cage designs (BAK and SynCage) performed differently with respect to immediate stabilization of the spine, whether the cages stabilized the spine significantly compared with its intact condition, and whether the addition of supplementary translaminar screw fixation further stabilized the spine. Stabilization was defined as a reduction in motion after insertion of an implant. METHODS: Twelve lumbar functional spinal units from human cadavera were tested under pure moments of flexion, extension, bilateral axial rotation, and bilateral lateral bending to a maximum of ten newton-meters. The relative intervertebral motions were measured, with use of an optoelectronic camera system, under three test conditions: with the spine intact, after insertion of anterior interbody cages, and after insertion of anterior interbody cages supplemented with translaminar screw fixation. Six specimens were tested for each type of cage: a bilateral, porous, threaded cylinder (BAK) and a central, porous, contoured implant with end-plate fit (SynCage). RESULTS: The cages performed in a similar manner in all directions of loading, with no significant differences between the two designs. The cages significantly stabilized the spine compared with its intact condition in flexion, axial rotation, and lateral bending (the median value for motion was 40, 48, and 29 percent of the value for the intact condition, respectively; p = 0.002 for all three directions). Compared with the cages alone, translaminar screw fixation provided no additional stabilizing effect in these directions but it significantly increased the stability of the spine in extension (the median value for motion was 34 percent of the value with the cages alone; p = 0.013). CONCLUSIONS: There were no differences in the stabilization provided by the two different cage designs. Use of the cages alone stabilized the spine in all directions except extension, and use of supplementary translaminar screw fixation provided additional stabilization only in extension. CLINICAL RELEVANCE: This study demonstrated that interbody cages do not stabilize the lumbar spine in extension, and this observation was not altered by the use of substantially different designs. If the lack of stabilization in extension is a clinical problem, possible solutions include the avoidance of extension postoperatively or the use of supplementary fixation.

The onset and progression of spinal injury: a demonstration of neutral zone sensitivity.

Spinal injuries are a great cost to society and the afflicted individuals. It is well known that most spinal injuries are not bony fractures but rather soft tissue lesions falling in the 'subfailure' region. For the clinical diagnosis of spinal injuries, abnormal motion patterns under physiological loads are considered an important factor. The purpose of the present study was to determine the onset and progression of spinal injury, and compare the sensitivity of three motion parameters: neutral zone (NZ), elastic zone (EZ), and range of motion (ROM). Spinal injury was defined as a significant increase in any of the three motion parameters. A repeatable high-speed flexion-compression load vector was applied individually to six porcine cervical spine specimens. Several impacts of increasing severity were applied to each specimen. After each impact, flexion-extension motion was measured. Neutral zone was the residual deformation from the neutral position to the position under zero load at the start of the final load cycle. Elastic zone was the displacement from zero load to the maximum load on the final load cycle. Range of motion was the sum of the neutral and elastic zones. The first significant increase in motion was determined by the neutral zone parameter with few observable anatomic lesions on the specimens. This was the onset of spinal injury. The next significant motion increase was also determined by the neutral zone parameter. After this motion increase, termed the progression of injury, ligament ruptures were observed in some specimens. It was concluded that the neutral zone was the most sensitive motion parameter in defining the onset and progression of spinal injury.(ABSTRACT TRUNCATED AT 250 WORDS)

In vitro axial preload application during spine flexibility testing: towards reduced apparatus-related artefacts.

Presently, there is little consensus about how, or even if, axial preload should be incorporated in spine flexibility tests in order to simulate the compressive loads naturally present in vivo. Some preload application methods are suspected of producing unwanted "artefact" forces as the specimen rotates and, in doing so, influencing the resulting kinematics. The objective of this study was to quantitatively compare four distinct types of preload which have roots in contemporary experimental practice. The specific quantities compared were the reaction moments and forces resulting at the intervertebral disc and specimen kinematics. The preload types incorporated increasing amounts of caudal constraint on the preload application vector ranging from an unconstrained dead-load arrangement to an apparatus that allowed the vector to follow rotations of the specimen. Six human cadaveric spine segments were tested (1-L1/L2, 3-L2/L3, 1-L3/L4 and 1-L4/L5). Pure moments were applied to the specimens with each of the four different types of compressive preload. Kinematic response was measured using an opto-electronic motion analysis system. A six-axis load cell was used to measure reaction forces and moments. Artefact reaction moments and shear forces were significantly affected by preload application method and magnitude. Unconstrained preload methods produced high artefact moments and low artefact shear forces while more constrained methods did the opposite. A mechanical trade-off is suggested by our results, whereby unwanted moment can only be prevented at the cost of shear force production. When comparing spine flexibility studies, caution should be exercised to ensure preload was applied in a similar manner for all studies. Unwanted moments or forces induced as a result of preload application method may render the comparison of two seemingly similar studies inappropriate.

Biomechanical properties of sterilized human auditory ossicles.

Bone allograft material is treated with sterilization methods to prevent the transmission of diseases from the donor to the recipient. The effect of some of these treatments on the integrity of the bone is unknown. This study was performed to evaluate the effect of several sterilization methods on the mechanical behaviour of human middle ear bones. Due to the size and composition of the bones (approximately 1.5 mm diameter by 4 mm long), mechanical testing options were limited to the traditional platens compression test. Experiments were first performed with synthetic bone to evaluate the precision of this test applied to small specimens. Following this, fresh frozen human ossicles were thawed and sterilized with (i) 1 N NaOH (n = 12); (ii) 0.9% LpH, a phenolic solution (n = 12); or (iii) steam at 134 degrees C (n = 18). A group of 26 control specimens did not receive any sterilization treatment. Material and structural properties were determined from axial compression testing. Results from the synthetic bone showed that the test was reproducible, with standard deviations less than 20% of the means. Significant differences occurred in stiffness and ultimate force values between NaOH-treated and autoclaved bones when compared to normals (p<0.05), but not for LpH-treated bones. LpH is not approved for medical use, so NaOH is the most appropriate of the treatments studied for the sterilization of ossicle allografts.

Design and evaluation of a cryogenic soft tissue fixation device -- load tolerances and thermal aspects.

Mechanical studies of soft connective tissues often encounter methodological difficulties, particularly in the secure fixation of the tissues. A simple, inexpensive technique which allowed stable cryofixation of soft tissues in uniaxial loading machines was developed. The cryogenic fixation device was evaluated in terms of its fixation strength and the temperature gradients within the tested tissues. Human patellar ligaments and quadriceps tendons were tested successfully to an average failure load of 2219N (S.D. 448N) with mid-substance failures occurring in 90% of the specimens. The temperature gradients within porcine flexor and extensor tendons were determined and found to exhibit a typical diffusion profile. The fixation quality was dependent upon the initial block temperature and the desired testing time. In summary, the cryofixation device presented here is an effective tool for soft tissue fixation but the effect of this type of fixation on internal tissue temperatures and possible testing times must be acknowledged.

The effect of injury on rotational coupling at the lumbosacral joint. A biomechanical investigation.

The lumbosacral joint is frequently indicated as a source of low-back pain, a cause of which may be abnormal patterns of vertebral motions. The goal of this study was to describe the influence of injury on the coupled motions of the L5-S1 joint in a human cadaveric model. Nine whole lumbosacral spine specimens were studied under the application of flexion, extension, left/right axial torque and right/left lateral bending pure moments. Injuries to the posterior ligaments, intervertebral disc, and articular facets at L5-S1 were produced, and the motion at L5-S1 was determined after each sequential injury. No significant coupled rotations were observed under flexion or extension moments. Under axial torque, lateral rotation at L5-S1 occurred to the same side as the applied torque and increased significantly only after injury to the intervertebral disc. Also coupled to axial torque was flexion rotation in the intact specimen, which became extension rotation after facetectomy. Under lateral bending moments, coupled axial rotation was to the opposite side of the applied moment and increased significantly only after removal of the facets of L5. Based on these results, it was concluded that intervertebral disc most resisted the coupled motion of lateral rotation under the application of axial torque, whereas the articular facets most resisted the coupled axial rotation under the application of lateral bending at the lumbosacral joint. Also, the facets were the structures that produced the flexion rotation of L5 on S1 under axial torque loading.

The effect of nucleotomy on lumbar spine mechanics in compression and shear loading.

STUDY DESIGN: An in vitro biomechanical investigation on human cadaveric specimens was conducted before and after nucleotomy. Endplate and vertebral body deformation patterns were measured under compression and shear loading, in addition to kinematics and disc pressure. OBJECTIVE: The working hypotheses of this study were that in compression, nucleotomy results in an altered deformation pattern of the endplate and that in shear, nucleotomy does not result in an altered endplate deformation pattern or disc pressure. SUMMARY OF BACKGROUND DATA: The pressure distributions within the intervertebral disc have been studied in compression loading but not in shear loading. Severe degeneration and surgical nucleotomy result in small nuclear pressure and altered loading distribution in compression. The effect of these changes on the vertebral endplate and the response under shear loads are not well understood. METHODS: Five L3-L4 and two L4-L5 functional spinal units were tested under compression and shear loading, intact and after nucleotomy. Vertebral body deformations, intradiscal pressure, and intervertebral kinematics were measured. A series of compression-type (maximum 1000 N) and shear-type (maximum 500 N) loads were applied. RESULTS: With nucleotomy, the disc pressure and the endplate strains decreased under compression, but the vertebral rim strains did not change. In shear, the vertebral rim and endplate strains did not change with nucleotomy. Disc pressure was lower in shear than in compression. CONCLUSION: Nucleotomy resulted in decreased disc pressure, decreased endplate deformation, and modified loading patterns onto the inferior vertebra in compression loading. However, nucleotomy did not appreciably affect the behavior of the disc in shear loading.

Mapping the structural properties of the lumbosacral vertebral endplates.

STUDY DESIGN: A biomechanical investigation using indentation tests in a human cadaveric model to seek variation in the structural properties across the lower lumbar and sacral endplates. OBJECTIVES: To determine 1) if there are regional differences in endplate strength and 2) whether any differences identified are affected by spinal level (lumbar spine vs. sacrum) or endplate (superior vs. inferior). SUMMARY OF BACKGROUND DATA: It has been postulated that some regions of the vertebral body may be stronger than others. Conclusive data, either supporting or disproving this theory, would be valuable for both spine surgeons and implant designers because one mode of failure of interbody implants is subsidence into one or both adjacent vertebrae. METHODS: Indentation tests were performed at 27 standardized test sites in 62 bony endplates of intact human vertebrae (L3-S1) using a 3-mm-diameter, hemispherical indenter with a test rate of 0.2 mm/sec to a depth of 3 mm. The failure load and stiffness at each test site were determined using the load-displacement curves. Three-way analyses of variance were used to analyze the resulting data. RESULTS: Both the failure load and stiffness varied significantly across the endplate surfaces (P < 0.0001), with posterolateral regions being stronger and stiffer than the central regions. Characteristic distributions were identified in the lumbar superior, lumbar inferior, and sacral endplates. The failure load distributions were found to differ in 1) the superior lumbar and sacral endplates (P = 0.0077), 2) the inferior lumbar and sacral endplates (P = 0.0014), and 3) the superior and inferior lumbar endplates (P < 0.0001). The sacral and inferior lumbar endplates were both found to be stronger than the superior lumbar endplates (sacrum, P = 0.054; inferior, P = 0.008) but were not themselves significantly different (P = 0.89). CONCLUSIONS: Highly significant regional strength and stiffness variations were identified in the lumbar and sacral endplates. The center of the bone, where implants are currently placed, is the weakest part of the lumbar endplates and is not the strongest region of the sacral endplate.

The role of the iliolumbar ligament in the lumbosacral junction.

The biomechanical function of the iliolumbar ligament in the human lumbosacral junction was investigated by analyzing the three-dimensional movements of the whole lumbar and lumbo-sacral-ilium specimens. The experiment was repeated in the following three conditions: 1) intact iliolumbar ligament, 2) right iliolumbar ligament transected, and 3) bilateral iliolumbar ligaments transected. The representative values of the increased motions, compared with intact, after transection of the bilateral iliolumbar ligaments were 1.7 degrees (23%) in flexion, 1.1 degrees (20%) in extension, 0.3 degrees (18%) in axial rotation, and 1.2 degrees (29%) in lateral bending. The most restricted motion governed by the iliolumbar ligament in the lumbosacral junction was lateral bending. The bilateral iliolumbar ligament specimen could restrict flexion and extension of the lumbosacral junction, but the unilateral iliolumbar ligament preparation alone could not restrict these motions. The iliolumbar ligament also had the function of restricting the rotational movement of the lumbosacral junction.