Automatic three-dimensional facial symmetry reference plane construction based on facial planar reflective symmetry net.

OBJECTIVES: Three-dimensional (3D) facial symmetry analysis is based on the 3D symmetry reference plane (SRP). Artificial intelligence (AI) is widely used in the dental and oral sciences. This study developed a novel deep learning model called the facial planar reflective symmetry net (FPRS-Net) to automatically construct an SRP and established a method for defining a 3D point-cloud region of interest (ROI) and high-dimensional feature computations suitable for this network model. METHODS: Overall, 240 patients were enroled. The deep learning model was trained and predicted using 200 samples, and its clinical suitability was evaluated with 40 samples. Four FPRS-Net models were prepared, each using supervised and unsupervised learning approaches based on full facial and ROI data (FPRS-NetS, FPRS-NetSR, FPRS-NetU, and FPRS-NetUR). These models were trained on 160 3D facial datasets, validated on 20 cases, and tested on another 20 cases. The model predictions were evaluated using an additional 40 clinical 3D facial datasets by comparing the mean square error of the SRP between the parameters predicted by the four FPRS-Net models and the truth plane. The clinical suitability of FPRS-Net models was evaluated by measuring the angle error between the predicted and ground-truth planes; experts evaluated the predicted SRP of the four FPRS-Net models using the visual analogue scales (VAS) method. RESULTS: The FPRS-NetSR and FPRS-NetU models achieved an average angle error of 0.84° and 0.99° in predicting 3D facial SRP, respectively, with a VAS value of >8. Using the four FPRS-Net models to create an SRP in 40 cases of 3D facial data required <4 s. CONCLUSIONS: Our study demonstrated a new solution for automatically constructing oral clinical 3D facial SRPs. CLINICAL SIGNIFICANCE: This study proposes a novel deep learning algorithm (FPRS-Net) to construct a symmetry reference plane that can reduce workload, shorten the time required for digital design, reduce dependence on expert experience, and improve therapeutic efficiency and effectiveness in dental clinics.

Chairside digital design and manufacturing method for children's band and loop space maintainers.

OBJECTIVES: This study proposes a chairside digital design and manufacturing method for band and loop space maintainers and preliminarily validates its clinical feasibility. METHODS: Clinical cases of 10 children requiring space maintenance caused by premature loss of primary teeth were collected. Intraoral scan data of the affected children were also collected to establish digital models of the missing teeth. Using a pediatric band and loop space maintainer design software developed by our research team, a rapid personalized design of band and loop structures was achieved, and a digital model of an integrated band and loop space maintainer was ultimately generated. A chairside space maintainer was manufactured through metal computer numerical control machining for the experimental group, whereas metal 3D printing in the dental laboratory was used for the control group. A model fitting assessment was conducted for the space maintainers of both groups, and senior pediatric dental experts were invited to evaluate the clinical feasibility of the space maintainers with regard to fit and stability using the visual analogue scale scoring system. Statistical analysis was also performed. RESULTS: The time spent in designing and manufacturing the 10 space maintainers of the experimental group was all less than 1 h. Statistical analysis of expert ratings showed that the experimental group outperformed the control group with regard to fit and stability. Both types of space maintainers met clinical requirements. CONCLUSIONS: The chairside digital design and manufacturing method for pediatric band and loop space maintainers proposed in this study can achieve same-day fitting of space maintainers at the first appointment, demonstrating good clinical feasibility and significant potential for clinical application.

Spatial Trueness Evaluation of 3D-Printed Dental Model Made of Photopolymer Resin: Use of Special Structurized Dental Model.

(1) Background: Various 3D printers are available for dental practice; however, a comprehensive accuracy evaluation method to effectively guide practitioners is lacking. This in vitro study aimed to propose an optimized method to evaluate the spatial trueness of a 3D-printed dental model made of photopolymer resin based on a special structurized dental model, and provide the preliminary evaluation results of six 3D printers. (2) Methods: A structurized dental model comprising several geometrical configurations was designed based on dental crown and arch measurement data reported in previous studies. Ninety-six feature sizes can be directly measured on this original model with minimized manual measurement errors. Six types of photo-curing 3D printers, including Objet30 Pro using the Polyjet technique, Projet 3510 HD Plus using the Multijet technique, Perfactory DDP and DLP 800d using the DLP technique, Form2 and Form3 using the SLA technique, and each printer's respective 3D-printable dental model materials, were used to fabricate one set of physical models each. Regarding the feature sizes of the simulated dental crowns and dental arches, linear measurements were recorded. The scanned digital models were compared with the design data, and 3D form errors (including overall 3D deviation; flatness, parallelism, and perpendicularity errors) were measured. (3) Results: The lowest overall 3D deviation, flatness, parallelism, and perpendicularity errors were noted for the models printed using the Objet30 Pro (overall value: 45 µm), Form3 (0.061 ± 0.019 mm), Objet30 Pro (0.138 ± 0.068°), and Projet 3510 HD Plus (0.095 ± 0.070°), respectively. In color difference maps, different deformation patterns were observed in the printed models. The feature size proved most accurate for the Objet30 Pro fabricated models (occlusal plane error: 0.02 ± 0.36%, occlusogingival direction error: -0.06 ± 0.09%). (4) Conclusions: The authors investigated a novel evaluation approach for the spatial trueness of a 3D-printed dental model made of photopolymer resin based on a structurized dental model. This method can objectively and comprehensively evaluate the spatial trueness of 3D-printed dental models and has a good repeatability and generalizability.

Three-Dimensional Virtual Reconstruction of External Nasal Defects Based on Facial Mesh Generation Network.

(1) Background: In digital-technology-assisted nasal defect reconstruction methods, a crucial step involves utilizing computer-aided design to virtually reconstruct the nasal defect's complete morphology. However, current digital methods for virtual nasal defect reconstruction have yet to achieve efficient, precise, and personalized outcomes. In this research paper, we propose a novel approach for reconstructing external nasal defects based on the Facial Mesh Generation Network (FMGen-Net), aiming to enhance the levels of automation and personalization in virtual reconstruction. (2) Methods: We collected data from 400 3D scans of faces with normal morphology and combined the structured 3D face template and the Meshmonk non-rigid registration algorithm to construct a structured 3D facial dataset for training FMGen-Net. Guided by defective facial data, the trained FMGen-Net automatically generated an intact 3D face that was similar to the defective face, and maintained a consistent spatial position. This intact 3D face served as the 3D target reference face (3D-TRF) for nasal defect reconstruction. The reconstructed nasal data were extracted from the 3D-TRF based on the defective area using reverse engineering software. The '3D surface deviation' between the reconstructed nose and the original nose was calculated to evaluate the effect of 3D morphological restoration of the nasal defects. (3) Results: In the simulation experiment of 20 cases involving full nasal defect reconstruction, the '3D surface deviation' between the reconstructed nasal data and the original nasal data was 1.45 ± 0.24 mm. The reconstructed nasal data, constructed from the personalized 3D-TRF, accurately reconstructed the anatomical morphology of nasal defects. (4) Conclusions: This paper proposes a novel method for the virtual reconstruction of external nasal defects based on the FMGen-Net model, achieving the automated and personalized construction of the 3D-TRF and preliminarily demonstrating promising clinical application potential.