Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 4 de 4
Filtrar
Mais filtros

Base de dados
Tipo de documento
País de afiliação
Intervalo de ano de publicação
1.
Acta Crystallogr Sect E Struct Rep Online ; 69(Pt 11): o1619, 2013 Oct 05.
Artigo em Inglês | MEDLINE | ID: mdl-24454069

RESUMO

The title compound, C10H13NO2, crystallizes with two crystallographically independent mol-ecules of similar geometry in the asymmetric unit; the six-membered oxazine rings adopts a half-chair conformation. Neither hydrogen bonds nor π-π inter-actions are observed in the crystal structure.

2.
J Immunol Res ; 2022: 2177884, 2022.
Artigo em Inglês | MEDLINE | ID: mdl-35310604

RESUMO

Background: Studies of chronic airway inflammatory diseases have increasingly focused on airway microbiota. However, the microbiota characteristics of asthma and chronic obstructive pulmonary disease (COPD) patients with different airway inflammatory phenotypes remain unclear. Objective: We aimed to reveal the differences of fungal and bacterial microbiota between eosinophilic asthma (EA) and noneosinophilic asthma (NEA) patients and between eosinophilic COPD (EC) and noneosinophilic COPD (NEC) patients. Further, explore whether similarities exist in the airway microbiota of patients with the same phenotype. Methods: Induced sputum samples were collected from 45 asthma subjects and 39 COPD subjects. The airway microbiota of the subjects was profiled by nearly full-length 16S rRNA and internal transcribed space (ITS) sequencing. Results: Subjects with eosinophilic phenotype (EA and EC) showed significant differences in both fungal and bacterial microbiota compared to the corresponding subjects with noneosinophilic phenotype (NEA and NEC). In addition, no differences were observed between the fungal microbiota of subjects with the same phenotype (EA vs. EC, NEA vs. NEC). In bacterial microbiota, the greater relative abundance of Streptococcus thermophilus was observed in EA and EC subjects, while Ochrobactrum was enriched in NEA and NEC subjects. In fungal microbiota, the EA and EC subjects showed higher relative abundances of Aspergillus and Bjerkandera, while the NEA and NEC subjects were enriched in Rhodotorula and Papiliotrema. Conclusions: Different airway inflammatory phenotypes were related to specific fungal and bacterial microbiota in both asthma and COPD, while the same airway inflammatory phenotype revealed a degree of similarity in airway microbiota, particularly in fungal microbiota.


Assuntos
Asma , Microbiota , Doença Pulmonar Obstrutiva Crônica , Humanos , Fenótipo , RNA Ribossômico 16S/genética
3.
Acta Crystallogr Sect E Struct Rep Online ; 67(Pt 8): o2056, 2011 Aug 01.
Artigo em Inglês | MEDLINE | ID: mdl-22091082

RESUMO

In the title compound, C(18)H(19)NO(2), the allyl group is disordered over two sets of sites [occupancy ratio 0.662 (4):0.338 (4)]. The dihedral angle between the phenyl and benzene rings is 87.44 (10)°. The oxazinane ring adopts a sofa conformation.

4.
RSC Adv ; 10(43): 25685-25695, 2020 Jul 03.
Artigo em Inglês | MEDLINE | ID: mdl-35518612

RESUMO

This paper presents a novel method using poly(aryl ether ketone) containing pendant carboxyl groups to covalently functionalize graphene oxide. The functionalized graphene oxide (LFG) was used to prepare poly(ether ether ketone) (PEEK) composites through melt blending. It is found that LFG has great interface adhesion to the PEEK matrix, and just a small amount of it can simultaneously improve the strength and toughness of the composites, while unmodified graphene oxide could enhance strength but cause toughness damage. The tensile and impact strength of composite with 0.1 wt% LFG are 5.7% and 20.5% higher than that of neat PEEK, respectively. In addition, 0.5 wt% LFG composite shows great friction and wear performance with friction coefficient and specific wear rate 27.3% and 18.3% lower than that of PEEK. Furthermore, the composites can be used as practical high-performance additive manufacturing materials because LFG is able to improve the mechanical performance of the fused deposition modeling (FDM) composite samples significantly.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA