RESUMO
Due to the lenient environmental policies in developing economies, mercury-containing wastes are partly produced as a result of the employment of mercury in manufacturing and consumer products. Worldwide, the presence of mercury as an impurity in several industrial processes leads to significant amounts of contaminated waste. The Minamata Convention on Mercury dictates that mercury-containing wastes should be handled in an environmentally sound way according to the Basel Convention Technical Guidelines. Nevertheless, the management policies differ a great deal from one country to another because only a few deploy or can afford to deploy the required technology and facilities. In general, elemental mercury and mercury-bearing wastes should be stabilized and solidified before they are disposed of or permanently stored in specially engineered landfills and facilities, respectively. Prior to physicochemical treatment and depending on mercury's concentration, the contaminated waste may be thermally or chemically processed to reduce mercury's content to an acceptable level. The suitability of the treated waste for final disposal is then assessed by the application of standard leaching tests whose capacity to evaluate its long-term behavior is rather questionable. This review critically discusses the main methods employed for the recovery of mercury and the treatment of contaminated waste by analyzing representative examples from the industry. Furthermore, it gives a complete overview of all relevant issues by presenting the sources of mercury-bearing wastes, explaining the problems associated with the operation of conventional discharging facilities and providing an insight of the disposal policies adopted in selected geographical regions.
Assuntos
Mercúrio , Eliminação de Resíduos , Materiais de Construção , Tecnologia , Instalações de Eliminação de ResíduosRESUMO
CeO2 nanoparticle-decorated ?-MnO2 nanotubes (NTs) were prepared and tested for elemental mercury (Hg0) vapor removal in simulated natural gas mixtures at ambient conditions. The composition which had the largest surface area and a relative Ce/Mn atomic weight ratio of around 35% exhibited a maximum Hg0 uptake capacity exceeding 20 mg?g?1 (2 wt %), as determined from measurements of mercury breakthrough which corresponded to 99.5% Hg0 removal efficiency over 96 h of exposure. This represents a significant improvement in the activity of pure metal oxides. Most importantly, the composite nanosorbent was repeatedly regenerated at 350 ?C and retained the 0.5% Hg0 breakthrough threshold. It was projected to be able to sustain 20 regeneration cycles, with the presence of acid gases, CO2, and H2S, not affecting its performance. This result is particularly important, considering that pure CeO2 manifests rather poor activity for Hg0 removal at ambient conditions, and hence, a synergistic effect in the composite nanomaterial was observed. This possibly results from the addition of facile oxygen vacancy formation at ?-MnO2 NTs and the increased amount of surface-adsorbed oxygen species.
RESUMO
The necessity to drastically act against mercury pollution has been emphatically addressed by the United Nations. Coal-fired power plants contribute a great deal to the anthropogenic emissions; therefore, numerous sorbents/catalysts have been developed to remove elemental mercury (Hg0 ) from flue gases. Among them, ceria (CeO2 ) has attracted significant interest, due to its reversible Ce3+ /Ce4+ redox pair, surface-bound defects and acid-base properties. The removal efficiency of Hg0 vapor depends among others, on the flue gas composition and temperature. CeO2 can be incorporated into known materials in such a way that the abatement process can be effective at different operating conditions. Hence, the scope of this account is to discuss the role of CeO2 as a promoter, active phase and support in the design of composite Hg0 sorbents/catalysts. The elucidation of each of these roles would allow the integration of CeO2 advantageous characteristics to such degree, that tailor-made environmental solution to complex issues can be provided within a broader application scope. Besides, it would offer invaluable input to theoretical calculations that could enable the materials screening and engineering at a low cost and with high accuracy.
RESUMO
Design and synthesis of efficient photocatalyst systems for a large volume of hydrogen (H2) evolution under solar light is still a great challenge. To obtain high photocatalytic activity, graphene-based semiconductor photocatalysts are gaining heightened attention in the field of green and sustainable fuel production due to their good electronic properties, high surface area and chemical stability. Herein, we demonstrate an efficient, novel and smart architecture of a graphene-based ZnIn2S4/g-C3N4 nanojunction by a simple hydrothermal process for H2 generation. In the present study, graphene (G) is chosen as the electron mediator and ZnIn2S4 (ZIS) and g-C3N4 (CN) are chosen as two different semiconductor photocatalysts to construct a smart architecture for the ternary photocatalytic system. Different characterization techniques such as XRD, TGA, FT-IR, SEM, TEM, HR-TEM, XPS, BET, and UV-vis DRS were employed to ensure the successful integration of graphene, ZnIn2S4, and g-C3N4 in the nanocomposite. As a result, high and efficient H2 evolution (477 µmol h-1 g-1) is attained for the graphene-based ZnIn2S4/g-C3N4 nanocomposite. Transient photocurrent experiments, ESR, PL, and time-resolved PL studies suggested that the intimate ternary nanojunction effectively promotes fast charge transfer and thereby enhances photocatalytic H2 evolution.
RESUMO
While many microfluidic devices have been developed for sensing and others for actuation, few devices can perform both tasks effectively and simultaneously on the same platform. In piezoelectric sensors and actuators, this is due to the opposing operating requirements for sensing and actuation. Sensing ideally requires narrow resonant peaks characterized by high quality factors, such as those found in quartz crystals. However, these materials usually have poor electromechanical coupling coefficients that are not ideal for actuation. In this work, we show that it is possible to achieve both sensing and actuation simultaneously on a shared device by exploiting the distinct advantages of both bulk waves for effective mass sensing and surface waves for highly efficient microfluidic actuation through a unique hybrid surface and bulk acoustic wave platform. In light of the recent resurgence of interest in portable inhaled insulin devices for personalized diabetes management, we demonstrate the use of this technology for efficient aerosolization of insulin for inhalation without denaturing the protein, while being able to concurrently detect the residual mass of the un-nebulized insulin remaining on the device such that the actual dose delivered to the patient can be determined in real time.
RESUMO
Mercury pollution threatens the environment and human health across the globe. This neurotoxic substance is encountered in artisanal gold mining, coal combustion, oil and gas refining, waste incineration, chloralkali plant operation, metallurgy, and areas of agriculture in which mercury-rich fungicides are used. Thousands of tonnes of mercury are emitted annually through these activities. With the Minamata Convention on Mercury entering force this year, increasing regulation of mercury pollution is imminent. It is therefore critical to provide inexpensive and scalable mercury sorbents. The research herein addresses this need by introducing low-cost mercury sorbents made solely from sulfur and unsaturated cooking oils. A porous version of the polymer was prepared by simply synthesising the polymer in the presence of a sodium chloride porogen. The resulting material is a rubber that captures liquid mercury metal, mercury vapour, inorganic mercury bound to organic matter, and highly toxic alkylmercury compounds. Mercury removal from air, water and soil was demonstrated. Because sulfur is a by-product of petroleum refining and spent cooking oils from the food industry are suitable starting materials, these mercury-capturing polymers can be synthesised entirely from waste and supplied on multi-kilogram scales. This study is therefore an advance in waste valorisation and environmental chemistry.
Assuntos
Mercúrio/química , Óleos de Plantas/química , Enxofre/química , Adsorção , Poluentes Atmosféricos/química , Varredura Diferencial de Calorimetria , Polímeros/síntese química , Polímeros/química , Reciclagem , Poluentes do Solo/química , Propriedades de Superfície , Termogravimetria , Poluentes Químicos da Água/químicaRESUMO
Piezoelectric acoustic wave devices integrated with noble metal surfaces provide exciting prospects for the direct measurement of toxic gas species such as mercury (Hg) in the atmosphere. Even though gold (Au) based acoustic wave sensors have been utilized extensively for detecting Hg, the potential of using other metal surfaces such as silver (Ag) is yet to be thoroughly studied. Here, we developed Ag sensitive layer-based surface acoustic wave (SAW) and quartz crystal microbalance (QCM) sensors and focused on their comparative analysis for Hg sensing applications with parameters such as the sensor sensitivity, selectivity, adsorption/desorption isotherm and Hg diffusion into the surface thoroughly studied. The SAW sensor was fabricated with nickel (Ni) interdigitated transducer (IDT) electrodes and a Ag thin film on the delay line of the device. In the case of the QCM sensor, the electrodes were constructed of Ag thin film and simultaneously employed as a sensitive layer. Mercury sensing experiments were conducted for a range of concentrations between 24-365 ppbv without/with the presence of some common industrial interfering gas species (i.e. ammonia, acetaldehyde, ethyl mercaptan, dimethyl disulphide, methyl ethyl ketone and humidity) at various operating temperatures in the range of 35-95 °C. The SAW sensor was found to possess up to 70 times higher response magnitudes than its QCM counterpart at 35 °C while up to 30 and 23 times higher response magnitudes were observed for the SAW sensor at elevated temperatures of 75 and 95 °C, respectively. Furthermore, the SAW sensor showed good selectivity (>89%) toward Hg(0) vapor in the presence of all the interferents tested at an operating temperature of 75 °C while the QCM sensor exhibited significant cross-sensitivity when ethyl mercaptan was introduced along with Hg(0) vapor. Overall, it is indicative that Ag-based acoustic wave sensors do have great potential for Hg sensing applications, given that right operating conditions are applied.
RESUMO
We developed a novel conductometric device with nanostructured gold (Au) sensitive layer which showed high-performance for elemental mercury (Hg(0)) vapor detection under simulated conditions that resemble harsh industrial environments. That is, the Hg(0) vapor sensing performance of the developed sensor was investigated under different operating temperatures (30-130 °C) and working conditions (i.e., humid) as well as in the presence of various interfering gas species, including ammonia (NH3), hydrogen sulfide (H2S), nitric oxide (NO), carbon mono-oxide (CO), carbon dioxide (CO2), sulfur dioxide (SO2), hydrogen (H2), methane (CH4), and volatile organic compounds (VOCs) such as ethylmercaptan (EM), acetaldehyde (MeCHO) and methyl ethyl ketone (MEK) among others. The results indicate that the introduction of Au nanostructures (referred to as nanospikes) on the sensor's surface enhanced the sensitivity toward Hg(0) vapor by up-to 450%. The newly developed sensor exhibited a limit of detection (LoD) (â¼35 µg/m(3)), repeatability (â¼94%), desorption efficiency (100%) and selectivity (â¼93%) when exposed to different concentrations of Hg(0) vapor (0.5 to 9.1 mg/m(3)) and interfering gas species at a chosen operating temperature of 105 °C. Furthermore, the sensor was also found to show 91% average selectivity when exposed toward harsher industrial gases such as NO, CO, CO2, and SO2 along with same concentrations of Hg(0) vapor in similar operating conditions. In fact, this is the first time a conductometric sensor is shown to have high selectivity toward Hg(0) vapor even in the presence of H2S. Overall results indicate that the developed sensor has immense potential to be used as accurate online Hg(0) vapor monitoring technology within industrial processes.
Assuntos
Gases/química , Mercúrio/química , Nanotecnologia/instrumentação , Compostos Orgânicos Voláteis/química , Amônia , Dióxido de Carbono , Ouro/química , Sulfeto de Hidrogênio , Limite de Detecção , Dióxido de EnxofreRESUMO
Microelectromechanical sensors based on surface acoustic wave (SAW) and quartz crystal microbalance (QCM) transducers possess substantial potential as online elemental mercury (Hg(0)) vapor detectors in industrial stack effluents. In this study, a comparison of SAW- and QCM-based sensors is performed for the detection of low concentrations of Hg(0) vapor (ranging from 24 to 365 ppbv). Experimental measurements and finite element method (FEM) simulations allow the comparison of these sensors with regard to their sensitivity, sorption and desorption characteristics, and response time following Hg(0) vapor exposure at various operating temperatures ranging from 35 to 75 °C. Both of the sensors were fabricated on quartz substrates (ST and AT cut quartz for SAW and QCM devices, respectively) and employed thin gold (Au) layers as the electrodes. The SAW-based sensor exhibited up to â¼111 and â¼39 times higher response magnitudes than did the QCM-based sensor at 35 and 55 °C, respectively, when exposed to Hg(0) vapor concentrations ranging from 24 to 365 ppbv. The Hg(0) sorption and desorption calibration curves of both sensors were found to fit well with the Langmuir extension isotherm at different operating temperatures. Furthermore, the Hg(0) sorption and desorption rate demonstrated by the SAW-based sensor was found to decrease as the operating temperature increased, while the opposite trend was observed for the QCM-based sensor. However, the SAW-based sensor reached the maximum Hg(0) sorption rate faster than the QCM-based sensor regardless of operating temperature, whereas both sensors showed similar response times (t90) at various temperatures. Additionally, the sorption rate data was utilized in this study in order to obtain a faster response time from the sensor upon exposure to Hg(0) vapor. Furthermore, comparative analysis of the developed sensors' selectivity showed that the SAW-based sensor had a higher overall selectivity (90%) than did the QCM counterpart (84%) while Hg(0) vapor was measured in the presence of ammonia (NH3), humidity, and a number of volatile organic compounds at the chosen operating temperature of 55 °C.
Assuntos
Ouro/química , Mercúrio/química , Sistemas Microeletromecânicos , Técnicas de Microbalança de Cristal de Quartzo , Som , Adsorção , Tamanho da Partícula , Propriedades de SuperfícieRESUMO
The detection of elemental mercury (Hg(0)) within industrial processes is extremely important as it is the first major step in ensuring the efficient operation of implemented mercury removal technologies. In this study, a 131 MHz surface acoustic wave (SAW) delay line sensor with gold electrodes was tested towards Hg(0) vapor (24 to 365 ppbv) with/without the presence of ammonia (NH3) and humidity (H2O), as well as volatile organic compounds (VOCs) such as acetaldehyde (MeCHO), ethylmercaptan (EM), dimethyl disulfide (DMDS) and methyl ethyl ketone (MEK), which are all common interfering gas species that co-exist in many industrial applications requiring mercury monitoring. The developed sensor exhibited a detection limit of 0.7 ppbv and 4.85 ppbv at 35 and 55 °C, respectively. Furthermore, a repeatability of 97% and selectivity of 92% in the presence of contaminant gases was exhibited by the sensor at the chosen operating temperature of 55 °C. The response magnitude of the developed SAW sensor towards different concentrations of Hg(0) vapor fitted well with the Langmuir extension isotherm (otherwise known as loading ratio correlation (LRC)) which is in agreement with our basic finite element method (FEM) work where an LRC isotherm was observed for a simplified model of the SAW sensor responding to different Hg contents deposited on the Au based electrodes. Overall, the results indicate that the developed SAW sensor can be a potential solution for online selective detection of low concentrations of Hg(0) vapor found in industrial stack effluents.
Assuntos
Eletrodos , Gases/análise , Ouro/química , Mercúrio/análise , Modelos Teóricos , Som , Compostos Orgânicos Voláteis/químicaRESUMO
Mercury being one of the most toxic heavy metals has long been a focus of concern due to its gravest threats to human health and environment. Although multiple methods have been developed to detect and/or remove dissolved mercury, many require complicated procedures and sophisticated equipment. Here, we describe a simple surface enhanced Raman spectroscopy (SERS) active ZnO/Ag nanoarrays that can detect Hg(2+), remove Hg(2+) and can be fully regenerated, not just from Hg(2+) contamination when heat-treated but also from the SERS marker when exposed to UV as a result of the self-cleaning ability of this schottky junction photocatalyst. The sensors are also highly selective because of the unique way mercury (among other chemicals) interacts with Ag nanoparticles, thus reducing its SERS activity.
Assuntos
Mercúrio/isolamento & purificação , Nanopartículas Metálicas/química , Análise Espectral Raman/métodos , Águas Residuárias/química , Mercúrio/análise , Prata/química , Análise Espectral Raman/instrumentação , Raios Ultravioleta , Eliminação de Resíduos Líquidos/métodos , Óxido de Zinco/químicaRESUMO
The charge transfer-mediated surface enhanced Raman scattering (SERS) of crystal violet (CV) molecules that were chemically conjugated between partially polarized silver nanoparticles and optically smooth gold and silver substrates has been studied under off-resonant conditions. Tyrosine molecules were used as a reducing agent to convert silver ions into silver nanoparticles where oxidised tyrosine caps the silver nanoparticle surface with its semiquinone group. This binding through the quinone group facilitates charge transfer and results in partially oxidised silver. This establishes a chemical link between the silver nanoparticles and the CV molecules, where the positively charged central carbon of CV molecules can bind to the terminal carboxylate anion of the oxidised tyrosine molecules. After drop casting Ag nanoparticles bound with CV molecules it was found that the free terminal amine groups tend to bind with the underlying substrates. Significantly, only those CV molecules that were chemically conjugated between the partially polarised silver nanoparticles and the underlying gold or silver substrates were found to show SERS under off-resonant conditions. The importance of partial charge transfer at the nanoparticle/capping agent interface and the resultant conjugation of CV molecules to off resonant SERS effects was confirmed by using gold nanoparticles prepared in a similar manner. In this case the capping agent binds to the nanoparticle through the amine group which does not facilitate charge transfer from the gold nanoparticle and under these conditions SERS enhancement in the sandwich configuration was not observed.
Assuntos
Corantes Fluorescentes/química , Ouro/química , Nanopartículas Metálicas/química , Prata/química , Estrutura Molecular , Tamanho da Partícula , Análise Espectral Raman , Propriedades de Superfície , Tirosina/químicaRESUMO
The emergence of three-dimensional (3D) printing promises a disruption in the design and on-demand fabrication of smart structures in applications ranging from functional devices to human organs. However, the scale at which 3D printing excels is within macro- and microlevels and principally lacks the spatial ordering of building blocks at nanolevels, which is vital for most multifunctional devices. Herein, we employ liquid crystal (LC) inks to bridge the gap between the nano- and microscales in a single-step 3D printing. The LC ink is prepared from mixtures of LCs of nanocellulose whiskers and large sheets of graphene oxide, which offers a highly ordered laminar organization not inherently present in the source materials. LC-mediated 3D printing imparts the fine-tuning required for the design freedom of architecturally layered systems at the nanoscale with intricate patterns within the 3D-printed constructs. This approach empowered the development of a high-performance humidity sensor composed of self-assembled lamellar organization of NC whiskers. We observed that the NC whiskers that are flat and parallel to each other in the laminar organization allow facile mass transport through the structure, demonstrating a significant improvement in the sensor performance. This work exemplifies how LC ink, implemented in a 3D printing process, can unlock the potential of individual constituents to allow macroscopic printing architectures with nanoscopic arrangements.
RESUMO
The role of natural gas in mitigating greenhouse gas emissions and advancing renewable energy resource integration is undoubtedly critical. With the progress of hydrocarbons exploration and production, the target zones become deeper and the possibility of mercury contamination increases. This impacts on the industry from health and safety risks, due to corrosion and contamination of equipment, to catalyst poisoning and toxicity through emissions to the environment. Especially mercury embrittlement, being a significant problem in LNG plants using aluminum cryogenic heat exchangers, has led to catastrophic plant incidents worldwide. The aim of this review is to critically discuss the conventional and alternative materials as well as the processes employed for mercury removal during gas processing. Moreover, comments on studies examining the geological occurrence of mercury species are included, the latest developments regarding the detection, sampling and measurement are presented and updated information with respect to mercury speciation and solubility is displayed. Clean up and passivation techniques as well as disposal methods for mercury-containing waste are also explained. Most importantly, the environmental as well as the health and safety implications are addressed, and areas that require further research are pinpointed.
RESUMO
Tailored synthesis of heterostructures for low temperature (sub 200⯰C) CO2 sensing continues to be a challenging task. The present study demonstrates CO2 sensing characteristics of CaO-ZnO heterostructures achieved by zinc hydroxide carbonate (Zn5(CO3)2(OH)6) conversion to ZnO using Ca(OH)2 at 50⯰C. Control samples namely, Zn5(CO3)2(OH)6, Ca(OH)2, ZnO, and CaO integrated microsensors exhibited low sensitivity towards CO2 gas. However, CaO-ZnO heterostructures demonstrated significant sensitivity (26 to 91%) at 150⯰C for gas concentration ranging from 100 to 10000â¯ppm, respectively. In this study, zinc hydroxide carbonate sensitized with 25â¯wt% Ca(OH)2 to form CaO-ZnO heterostructures (25CaZMS) displayed a promising sensitivity (77%) and selectivity (98%) towards 500â¯ppm CO2 gas. Moreover, the selectivity studies were conducted in the presence of 10 commonly found gases and their sensing performance was compared against CO2 gas in dry and humid conditions. The developed CaO-ZnO sensor exhibited faster kinetics in comparison to the control samples. Improved sensing performance observed here is attributed to the low-temperature synthesis route which resulted in a large number of active pores and high surface area morphology. Additionally, the high CO2 adsorption capacity of CaO combined with compatible n-type semiconductors in forming highly dynamic nano-interfaced heterostructure is a promising step towards developing a precise CO2 gas microsensor.
RESUMO
Enormous efforts have been initiated in the production of biobased fuels and value-added chemicals via biorefinery owing to the scarcity of fossil resources and huge environmental synchronization. Herein, non-noble metal-based metal/mixed metal oxide supported on carbon employing a metal-organic framework as a sacrificial template is demonstrated for the first time in the selective hydrodeoxygenation (HDO) of biomass-derived furfural (FFR) to 2-methyl furan (MF). The aforementioned catalyst (referred to as Cu/CuFe2O4@C-A) exhibited extraordinary catalytic proficiency (100% selectivity toward MF) compared with the conventional Cu/CuFe2O4@C-B catalyst which was prepared by the wet impregnation method. High-resolution transmission electron microscopy and synchrotron X-ray diffraction studies evidenced the existence of both metal (Cu) and mixed metal oxide (CuFe2O4) phases, in which the metal could help in hydrogenation to alcohol and metal oxide could assist in the hydroxyl group removal step during HDO reaction. The stabilization of encapsulated metal/metal oxide nanoparticles in the carbon matrix, modulation of the electronic structure, and regulation of geometric effects in the Cu/CuFe2O4@C-A are thought to play an important role in its excellent catalytic performance, confirmed by X-ray photoelectron spectroscopy and X-ray absorption spectroscopy investigations. Furthermore, the structure and activity interconnection was confirmed by in situ attenuated total reflection-IR studies, which manifested the strong interfacial interaction between FFR and the Cu/CuFe2O4@C-A catalyst. This finding was further supported by NH3 temperature-programmed desorption analysis, which suggested that the presence of more Lewis/weak acidic sites in this catalyst was beneficial for the hydrogenolysis step in HDO reaction. Additionally, H2 temperature-programmed reduction studies revealed that the adsorption of H2 was stronger on the Cu/CuFe2O4@C-A than that over the conventional Cu/CuFe2O4@C-B catalyst; thus, the former catalyst promoted activation of H2. A detailed kinetic analysis which demonstrated the lower activation energy barrier along with dual active sites attributed for the activation of the two separate reactions in the HDO process on the Cu/CuFe2O4@C-A catalyst. This work has great implication in developing a highly stable catalyst for the selective upgradation of biomass without deactivation of metal sites in extended catalytic cycles and opens the door of opportunity for developing a sustainably viable catalyst in biomass refinery industries.
RESUMO
The high demand for H2 gas sensors is not just limited to industrial process control and leak detection applications but also extends to the food and medical industry to determine the presence of various types of bacteria or underlying medical conditions. For instance, sensing of H2 at low concentrations (<10 ppm) is essential for developing breath analyzers for the noninvasive diagnosis of some gastrointestinal diseases. However, there are major challenges to overcome in order to achieve high sensitivity and hence low limit of detection (LoD) toward H2. In this study, it is demonstrated that light-assisted amperometric gas sensors employing sensitive layers based on Pd-decorated TiO2 long-range ordered crystals can achieve excellent H2 sensing performance. This unique combination of materials and novel layered structure enables the detection of H2 gas down to 50 ppm with highly promising LoD capabilities. The sensor response profiles revealed that the sensor's signal-to-noise ratio was higher in the presence of light when operated with a 9 V bias (relative to other conditions used), producing a LoD of only 3.5 ppm at an operating temperature of 33 °C. The high performance of the sensor makes it attractive for applications that require low-level (ppm as opposed to conventional % levels) H2 gas detection. Most importantly, the developed sensor exhibited high selectivity (>93%) toward H2 over other gas species such as CO2, C4H8O, C3H6O, CH3CHO, and NO, which are commonly found to coexist in the environment.
Assuntos
Hidrogênio , Titânio , Limite de Detecção , TemperaturaRESUMO
Using colloidal lithography, a series of inverted long-range ordered crystals (i-LROCs) of Pd honeycombs were fabricated on quartz crystal microbalance (QCM) sensors. The structures formed provided the required platform for the proceeding galvanic replacement reaction (GR) process to generate seamless Au nanoparticle deposits throughout the i-LROC. The results showed that controlling the dimensions of the pores in the developed Pd i-LROCs is important in the formation of gold deposition sites on the uniform structures through the GR reaction process. The developed Pd/Au i-LROC deposited sensors showed significant enhancement in the sensitivity toward Hg0 vapor when compared to pure Pd structures, with limit of detection improving from 60.0 to 13.7⯵g/m3, respectively. Furthermore, a significant improvement in the modified sensor's selectivity toward Hg0 in the presence of other industrial related gas species was observed which is attributed to the addition of Au to the Pd structures through GR reaction.
RESUMO
While glucose monitoring technology is widely available, the continued prevalence of diabetes around the world coupled with its debilitating effects continues to grow. The significant limitations which exist in the current technology, instils the need for materials capable of non-invasive glucose detection. In this study a unique non-enzymatic electrochemical glucose sensor was developed, utilising a gold honeycomb-like framework upon which sharp Co3O4 needles are anchored. This composite nanomaterial demonstrates excellent sensing performance in glucose concentrations ranging between 20⯵M and 4â¯mM, exceeding the range required for non-invasive glucose sensing. In conjunction with this high sensitivity (2.014â¯mAâ¯mM-1·cm-2), the material possesses excellent selectivity towards glucose for commonly interfering physiological species such as uric acid and ascorbic acid. Glucose detection in synthetic saliva was then performed showing excellent capability in the low concentration range (20⯵M-1â¯mM) for non-invasive sensing performance. Further tests showed good selectivity of the sensor in physiological contaminants commonly found in saliva such as cortisol and dopamine. This development provides excellent scope to create next-generation non-invasive diabetes monitoring platforms, with excellent performance when detecting low glucose concentrations in complex solutions such as saliva.
Assuntos
Técnicas Biossensoriais/métodos , Cobalto/química , Glucose/análise , Ouro/química , Nanoestruturas/química , Óxidos/química , Saliva/química , Automonitorização da Glicemia/métodos , Técnicas Eletroquímicas/métodos , Humanos , Limite de Detecção , Nanoestruturas/ultraestrutura , PorosidadeRESUMO
The incorporation of high-aspect-ratio nanostructures across surfaces has been widely reported to impart antibacterial characteristics to a substratum. This occurs because the presence of such nanostructures can induce the mechanical rupture of attaching bacteria, causing cell death. As such, the development of high-efficacy antibacterial nano-architectures fabricated on a variety of biologically relevant materials is critical to the wider acceptance of this technology. In this study, we report the antibacterial behavior of a series of substrata containing multi-directional electrodeposited gold (Au) nanospikes, as both a function of deposition time and precursor concentration. Firstly, the bactericidal efficacy of substrata containing Au nanospikes was assessed as a function of deposition time to elucidate the nanopattern that exhibited the greatest degree of biocidal activity. Here, it was established that multi-directional nanospikes with an average height of â¼302 nm ± 57 nm (formed after a deposition time of 540 s) exhibited the greatest level of biocidal activity, with â¼88% ± 8% of the bacterial cells being inactivated. The deposition time was then kept constant, while the concentration of the HAuCl4 and Pb(CH3COO)2 precursor materials (used for the formation of the Au nanospikes) was varied, resulting in differing nanospike architectures. Altering the Pb(CH3COO)2 precursor concentration produced multi-directional nanostructures with a wider distribution of heights, which increased the average antibacterial efficacy against both Gram-negative Pseudomonas aeruginosa and Gram-positive Staphylococcus aureus bacteria. Importantly, the in situ electrochemical fabrication method used in this work is robust and straightforward, and is able to produce highly reproducible antibacterial surfaces. The results of this research will assist in the wider utilization of mechano-responsive nano-architectures for antimicrobial surface technologies.