The effective treatment of dye-containing simulated wastewater by using the cement kiln dust as an industrial waste adsorbent.

This study compares the adsorption behavior of both Methylene Blue (MB) and Congo Red (CR) dyes on the surfaces of cement kiln dust (CKD) powder from the experimentally simulated wastewater solution. The cement kiln dust powder was characterized using X-ray Fluorescence (XRF), X-ray diffraction (XRD), N2 adsorption-desorption Brunauer-Emmett-Teller (BET), Fourier Transform Infrared Spectroscopy (FTIR), and Scanning Electron Microscopy (SEM) tests. The adsorption for such dyes was studied under varying mixing contact times, temperatures, and pH as well as various initial concentrations of both dyes and adsorbent using the batch mode experiments. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were applied, and the results revealed that the pseudo-second-order fitted well to the kinetic data. Thermodynamic parameters stated that the adsorption process was endothermic. Studying Linear and nonlinear forms of Langmuir and Freundlich's adsorption isotherms revealed that the adsorption process was followed by both homogeneous mono-layer and heterogeneous multilayer coverage on the active sites of cement kiln dust particles. The data showed that the adsorption capacities of the methylene blue and Congo red dyes were 58.43 and 123.42 mg/g, respectively and cement kiln dust is an adsorbent with little cost for the treatment of wastewater.

Upcycling of sugar refining mud solid waste as a novel adsorbent for removing methylene blue and Congo red from wastewater.

The feasibility of utilizing the mud solid waste (MSW) produced during the carbonation process of sugar refining as a cost-effective and environmentally friendly alternative for the water removal of methylene blue (MB) and Congo red (CR), being highly utilized organic dyes representing cationic and anionic species, respectively is presented. Prior to its use, the MSW was dried at 110 °C for 24 h and sieved through a 100-mesh screen. The chief constituent of the MSW utilized was CaCO3, with a point of zero charge (PZC) found at pH 8.4 and 7.96 m2 g-1 total surface area. XRD and FTIR data indicate the presence of interactions between the dyes and the MSW surface, indicating effective adsorption. Different variables, such as initial dye concentration, MSW weight, solution pH, contact time, and temperature, were all examined to determine the optimal dye removal conditions. A central composite design (CCD) approach based on response surface methodology (RSM) modeling was utilized to identify statistically significant parameters for MB and CR adsorption capacities onto the MSW adsorbent. The removal equilibrium was typically reached in 120 minutes, with the greatest removal efficiency of CR taking place at pH 2 and 328 K, while the highest MB removal efficiency was obtained at pH 12 and 296 K. Kinetic studies suggest the adsorption of both dyes on the MSW follow pseudo-second-order rates, as evident through the high correlations obtained. Linearized and non-linearized Langmuir models showed strong correlations indicating maximum adsorption capacities of 86.6 and 72.3 mg g-1 for MB and CR, respectively. High regeneration and reusability potential of the MSW was demonstrated especially for the adsorption of CR, where the removal efficiency was nearly constant throughout five adsorption cycles, ranging from 93 to 91%, while the reduction in the removal for MB was much more significantly impacted, diminishing from 95 to 79% after the five cycles.

Development of novel amino-ethyl chitosan hydrogel for the removal of methyl orange azo dye model.

The present study introduces a new and straightforward method for the amination of Chitosan. This method involves coupling Chitosan (CS) with 2-chloroethylamine (ENH2) in a single step to produce an amino-ethyl Chitosan derivatives with increased amine group content (CS-ENH2) using click chemistry. The resulting derivatives were then crosslinked using Glutaraldehyde to form amino-ethyl Chitosan Schiff bases. The novel amino-ethyl Chitosan Schiff bases were subsequently utilized as adsorbents for the removal of Methyl Orange (MO) dye from aqueous solutions using a batch technique, and the performance of the produced Schiff bases was compared with that of the native Chitosan Schiff base. The CS-ENH2 adsorbents show improved adsorption capacity up to 300% of the native Chitosan Schiff base with almost double removal rate. The adsorption temperature has a positive impact in general while almost 100% of MO removed at 60 °C using CS-ENH2 adsorbents compared with 66% of the native Chitosan Schiff base adsorbent. The adsorption pH shows a negative impact on the MO removal percent. That effect reduced sharply using the CS-ENH2 adsorbents with higher amination degree while the MO removal percent almost being constant over a wide range of pH; 2.0-7.0. The agitation speed has the same positive effect over all the adsorbents. However, the rate of MO removal percent decreased with increase the agitation speed up to 250 rpm. The experimental findings demonstrated that the highest percentage of MO dye removal was achieved under the conditions of pH 2.0, a temperature of 60 °C, agitation speed of 250 rpm, and adsorption duration of 90 min. These Schiff bases were subsequently characterized using advanced analytical techniques including Fourier Transform Infrared spectroscopy, Thermal analysis (TGA and DSC), and Scanning Electron Microscopy.

Novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogel development for Methyl orange removal from waste water.

In the modern era, with the rapid growth of various industries, the issues of energy crisis and environmental pollution have garnered increasing attention. One significant source of industrial pollution is printing and dyeing wastewater. This wastewater often contains dyes that have aromatic structures and azo groups, such as Methyl orange (MO), which are both toxic and difficult to degrade. If these dyes are released into the wastewater stream without any treatment, they can have adverse effects on ecological balance and human health. Therefore, it is crucial to identify suitable treatment strategies to efficiently remove dyes from wastewater systems before discharge. In this study, the Methyl orange (MO) azo dye has been removed from dyes-contaminated wastewater, for the first time, using a novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogel (AECMC). Different characterization methods, including FTIR, TGA, and DSC were used to characterize the generated AECMC compounds. The water absorption and cationic exchange capacities were assessed. Factors affecting the MO anions adsorption including MO concentration, adsorption pH, temperature, time, adsorbent dose, and agitation speed have been investigated. Moreover, the kinetics of the adsorption process was assessed by the use of three models: pseudo-first-order, Pseudo-second-order, and Elovich. Moreover, the mechanism of the adsorption process was monitored using the Intraparticle diffusion and Boyd models. Additionally, the adsorption isotherm was examined using established models such as Langmuir, Freundlich, and Temkin isotherms. The thermodynamic characteristics of the MO adsorption process have been investigated at various adsorption temperatures using the Van't Hoff model. The results obtained from the study indicate that the process of MO adsorption adhered to the Pseudo-second-order kinetic model, the Langmuir isotherm model was found to be applicable, and spontaneous and exhibited an endothermic character. In conclusion, the developed novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogels (AECMC) have successive in the removal of the MO anionic dye from contaminated wastewater.

Synthetic Degradable Polyvinyl Alcohol Polymer and Its Blends with Starch and Cellulose-A Comprehensive Overview.

Approximately 50% of global plastic wastes are produced from plastic packaging, a substantial amount of which is disposed of within a few minutes of its use. Although many plastic types are designed for single use, they are not always disposable. It is now widely acknowledged that the production and disposal of plastics have led to a plethora of negative consequences, including the contamination of both groundwater and soil resources and the deterioration of human health. The undeniable impact of excessive plastic manufacturing and waste generation on the global plastic pollution crisis has been well documented. Therefore, degradable polymers are a crucial solution to the problem of the non-degradation of plastic wastes. The disadvantage of degradable polymers is their high cost, so blending them with natural polymers will reduce the cost of final products and maximize their degradation rate, making degradable polymers competitive with industrial polymers that are currently in use daily. In this work, we will delineate various degradable polymers, including polycaprolactone, starch, and cellulose. Furthermore, we will elucidate several aspects of polyvinyl alcohol (PVA) and its blends with natural polymers to show the effects of adding natural polymers on PVA properties. This paper will study cost-effective and ecologically acceptable polymers by combining inexpensive natural polymers with readily accessible biodegradable polymers such as polyvinyl alcohol (PVA).

Sustainable and energy-efficient photocatalytic degradation of textile dye assisted by ecofriendly synthesized silver nanoparticles.

In this study, we have touched on two goals of sustainable development, namely, the provision of clean water and sanitation and clean energy at acceptable prices, hoping for good health for all ages. A green economical method was used to prepare silver nanoparticles from chitosan biopolymer. AgNPs were fully characterized using UV-Vis, FTIR, XRD, HR-TEM, and EDX analysis. Different concentrations (0.02-0.18 g/L) of the nanoparticles were integrated into a mixture of heterogeneous nano photocatalysts TiO2 and ZnO (1:1 weight ratio) under UV irradiation for the photocatalytic degradation of Acid Red 37 textile dye to obtain clean water. The kinetic description of the performed photocatalytic process was presented assuming a pseudo-first-order reaction. The data revealed that increasing the concentration of AgNPs in the catalytic mixture showed a high apparent rate constant (kapp) accompanied by an increase in the apparent quantum yield (%Qapp), followed by dye destruction after a very short time (t0.5 = 3 min). Since the photocatalytic degradation process consumes electrical energy, the electrical energy per order (EE/O) was calculated, showing a low value of 20 kWh/m3/order, using 0.18 g/L AgNPs, indicating that the elicited photocatalytic degradation method is a sustainable one for the mineralization of the targeted dye.

Biodegradable cellulose nanocrystals hydrogels for removal of acid red 8 dye from aqueous solutions.

Biodegradable cellulose nanocrystals hydrogels (CNCsH) were synthesized from cellulose nanocrystals (CNCs) which were prepared from office wastepaper (OWP) by a chemical crosslinking method using epicholorohydrin (ECH) as a cross-linker. CNCsH were tested for their swelling behavior and biodegradability and the point of zero charge had been determined. The ability of CNCsH for removing the Acid Red 8 (AR8) anionic dye from its aqueous solution was evaluated. The different parameters affecting removal of the dye, such as pH, initial concentration of dye, content of CNCs, temperature and adsorbent dosage were investigated. The optimum conditions for 68% removal efficiency were pH = 1, initial concentration of dye = 10 ppm, contact time = 105 min, CNCs content = 5% and CNCsH dosage = 0.5 g at 30 °C. The adsorption isotherms, kinetics, and thermodynamic parameters have been studied. The results showed an appropriate fit for Langmuir adsorption isotherm and pseudo-second order kinetics model with an adsorption capacity of 17.12 mg/g. According to the obtained values of thermodynamic parameters, the removal of Acid red 8 by CNCs hydrogels was exothermic spontaneous process.

The superior photocatalytic performance and DFT insights of S-scheme CuO@TiO2 heterojunction composites for simultaneous degradation of organics.

The necessity to resolve the issue of rapid charge carrier recombination for boosting photocatalytic performance is a vigorous and challenging research field. To address this, the construction of a binary system of step-scheme (S-scheme) CuO@TiO2 heterostructure composite has been demonstrated through a facile solid-state route. The remarkably enhanced photocatalytic performance of CuO@TiO2, compared with single TiO2, which can consequence in the more efficient separation of photoinduced charge carriers, reduced the band gap of TiO2, improved the electrical transport performance, and improved the lifetimes, thus donating it with the much more powerful oxidation and reduction capability. A photocatalytic mechanism was proposed to explain the boosted photocatalytic performance of CuO@TiO2 on a complete analysis of physicochemical, DFT calculations, and electrochemical properties. In addition, this work focused on the investigation of the stability and recyclability of CuO@TiO2 in terms of efficiency and its physical origin using XRD, BET, and XPS. It is found that the removal efficiency diminishes 4.5% upon five recycling runs. The current study not only promoted our knowledge of the binary system of S-scheme CuO@TiO2 heterojunction composite photocatalyst but also shed new light on the design of heterostructure photocatalysts with high-performance and high stability.

Innovative high-density polyethylene/waste glass powder composite with remarkable mechanical, thermal and recyclable properties for technical applications.

Several reinforcement materials are incorporated into a polymeric matrix to improve the mechanical properties and reduce the cost of the obtained composites. In this work, recycled high-density polyethylene/waste glass powder composites, compatibilized with maleic anhydride-grafted polyethylene, were prepared using a two-roll mill and compression molding techniques. Four levels of waste glass powder, 2, 10, 20 and 30% by weight, and five levels of the compatibilizer, polyethylene grafted with maleic anhydride (0.5, 1.5, 2.5, 5 and 7.5%by weight), were used. The effect of adding waste glass powder and compatibilizer concentration on the composite's mechanical properties, such as tensile strength, tensile strain, tensile modulus and thermal properties was studied. The results showed that superior mechanical properties were obtained and that the tensile strength and modulus increased with increasing waste glass powder content and compatibilizer concentration by 20 and 1.5 wt%, respectively. However, the elongation at the break decreased with the increase in both factors. The composite, which was prepared under ideal conditions, has high thermal stability and can be easily recycled and reprocessed for five cycles with high mechanical properties. This study recommends that the prepared composite, under optimum conditions, can be used as a cost-effective automobile dashboard material.

Antibiotic-free combinational hyaluronic acid blend nanofibers for wound healing enhancement.

An innovative approach in the functionalization of nanofibers (NFs) for wound healing relies on non-antibiotic combinational therapy to subdue microbial invasion while reducing antimicrobial resistance and enhancing healing. Despite great potentials, wound healing efficacy of NFs embedding antimicrobial metal nanoparticles (NPs)/essential oils has been scarcely documented. We developed combinational NFs using an electrospinnable hyaluronic acid/polyvinyl alcohol/polyethylene oxide blend embedding a new ZnO NPs/cinnamon essential oil (CEO) antimicrobial combination. Fourier transform infrared, X-ray diffraction and transmission electron microscopy confirmed the presence of HA and distribution of ZnO NPs and CEO within NFs. Results for mean diameter, thermal stability, hydrophilicity, tensile strength, in vitro biodegradability, and cytocompatibility of crosslinked combinational NFs were intermediate between those of their singly loaded counterparts. All NFs inhibited the growth of Staphylococcus aureus (S. aureus). Compared with singly loaded NFs, combinational NFs showed the greatest healing efficacy of full thickness S. aureus inoculated incision wounds in rats in terms of bacterial inhibition following a single application, healing speed, and quality of skin structure recovery as verified by morphological, microbiological, and histopathological studies. Results highlighted the potentials of metal NPs/essential oil functionalization of nanofibrous wound dressings as an emerging antibiotic-free combinational approach for more effective and safer wound healing.