Influence of Light-Curing Glaze and Chlorhexidine Gluconate in the Acrylic Resin Properties: An in situ Study.

This in-situ study aimed to evaluate the chromatic stability, microhardness, and surfacefree energy of chemically activated acrylic resin (CAAR) samples. Eighty CAAR samples were made and each volunteer (n = 20) received two palatal plates with two sides of groups (without and with glaze application). The samples were exposed to two conditions: the control condition (sucrose 30%) and the test condition (sucrose 30% and 0.12% chlorhexidine). The volunteers used the first palatal device (control condition) for seven days and the second palatal device (test condition) for another seven days, with a seven-day break between them. Then, the ΔΕ00, microhardness, and surface-free energy tests were performed. Analysis of Variance and the Tukey test were used (α = 0.05). The control group with glaze showed higher ΔΕ00 compared to the group without the glaze. The test group with glaze had less ΔΕ00 than their respective controls. In both periods, when the glaze was applied, higher microhardness values were found for all groups. Groups with glaze showed lower roughness and higher surface-free energy than groups without the glaze. The values obtained in this study were satisfactory, showing the clinical efficacy of glaze and the use of 0.12% CH for maintaining the physical and mechanical properties of CAAR.

Cross-cultural measurement equivalence of the Healthy Eating Index adapted version for children aged 1-2 years.

The objectives of this study were to evaluate the cross-cultural measurement equivalence of the Healthy Eating Index (HEI) for children aged 1-2 years and to analyse the quality of nutrition of preterm infants. This was a cross-sectional study with 106 premature infants attended in two specialised outpatient clinics of university hospitals. The quality of the diet was analysed through an adapted HEI to meet the dietary recommendations of Brazilian children aged 1-2 years. Food consumption was measured by 24-h recalls. The reliability of the instrument was evaluated by internal consistency analysis and inter-observer reliability using Cronbach's α coefficient and κ with quadratic ponderation. The construct validity was evaluated by principal component analysis and by Spearman's correlation coefficient with total energy and consumption of some groups' food. The diet quality was considered adequate when the total HEI score was over 80 points. Cronbach's α was 0·54. Regarding inter-observer reliability, ten items showed strong agreement (κ > 0·8). The item scores had low correlations with energy consumed (r ≤ 0·30), and positive and moderate correlation of fruit (r 0·67), meat (r 0·60) and variety of diet (r 0·57) with total scores. When analysing the overall quality of the diet, most patients need improvement (median 78·7 points), which can be attributed to low total vegetable intake and the presence of ultraprocessed foods in the diet. The instrument showed auspicious psychometric properties, being promising to evaluate the quality of the diet in children aged 1-2 years.

Effect of photopolymerized glaze application on bacterial adhesion on ocular acrylic resin surfaces submitted to accelerated ageing.

Conditions of the acrylic resin (AR) surface, such as roughness, can promote a favourable environment for the adhesion of micro-organisms, even on the surface of ocular prostheses. This study evaluated the influence of photopolymerized glaze application on the roughness of ARs and adhesion of Staphylococcus aureus and Staphylococcus epidermidis on ocular AR surfaces submitted to accelerated ageing. Two hundred and eighty-eight samples of white colour (N1) and colourless ARs were distributed in eight groups (n = 9), based on surface treatments (glaze or ARs submitted to only a final polishing), accelerated ageing (before and after) and periods of microbial growth (24- and 48-h). The roughness average (Ra) and total height of roughness profile (Rt) values were greater for the groups with glaze and increased for all groups after ageing. The microbial adhesion among the groups with and without glaze did not present a statistically significant difference. The ageing did not statistically affect the adhesion of Staph. epidermidis, but affected the adhesion of Staph. aureus, which presented an increase after 24 h of growth on only N1 AR with glaze. These results demonstrate that the glaze did not contribute to adhesion of Staph. aureus and Staph. epidermidis, which are responsible for most ocular prosthetic infections. SIGNIFICANCE AND IMPACT OF THE STUDY: Some recent evidence suggested that the surface finish of ocular prostheses influences the accumulation of deposits that can affect the interaction with pathogenic bacteria, increasing the probability of infections. In addition, surface deterioration over time can increase the roughness and, consequently, biofilm formation. Thus, a better understanding of the influence of surface finish on bacterial adhesion becomes extremely important. In this study, we tested a glaze for surface polishing compared to mechanical polishing, before and after ageing. The results suggest that the glaze did not contribute to microbial adhesion and might be useful in preventing possible prosthetic infections.

On the stability in alkaline conditions and electrochemical performance of A2BO4-type cathodes for liquid fuel cells.

Typical direct liquid fuel cells (DLFCs) use a liquid fuel and O2 as the oxidant. However, for applications where O2 is not available (e.g., space and underwater), the gas has been replaced by H2O2 as a liquid oxidant. This work presents a study of various ceramic disc electrodes with K2NiO4 structure and nominal compositions La2NiO4, La2CuO4, La1.9Pr0.1CuO4, La1.9Sr0.1CuO4, La1.8Ce0.2NiO4, La1.9Pr0.1NiO4, La1.8Pr0.2NiO4 and La1.9Sr0.1NiO4 to assess their stability and activity for the hydrogen peroxide reduction reaction (HPRR) in alkaline media. Stability tests conducted in 2 M NaOH show that Ni and Cu are readily dissolved, as occurs for substituting elements such as Sr, in agreement with calculated Pourbaix diagrams. Such degradation affects the surface of the materials, which is depleted of transition metals. This has consequences for the ORR and HPRR activity due to formation of a La-rich passivation layer on the surface. Only La2CuO4 and La1.8Ce0.2NiO4 display HPRR activity at around -0.25 V vs. RHE. An attempt is made to correlate the composition, chemical stability and electrochemical behaviour of these materials based on known molecular-orbital models proposed for the oxygen reduction reaction.

Microbiological analysis of conjunctival secretion in anophthalmic cavity, contralateral eye and ocular prosthesis of patients with maxillofacial abnormalities.

The purpose of this study was to identify and analyse the micro-organisms present in the conjunctival secretion in anophthalmic cavities of wearers of ocular prostheses, as well as on the prostheses used by them, correlating them with the microbiota of the contralateral eye. Nine patients with maxillofacial abnormalities, wearers of an acrylic resin ocular prosthesis participated in the study. Collections of conjunctival secretions and biofilm were performed on the prosthesis, anophthalmic cavity and contralateral eye for the mycological and bacterial analyses. The data were submitted to statistical analysis, performing a Kendall correlation test to identify the correlation between the collection site and the identified micro-organism (P < 0·05). It was verified that the most prevalent micro-organisms were the Staphylococcus aureus and Staphylococcus epidermidis, independent of the collection site, and that negative cultures for fungi were encountered in 85·2% of collections, independent of the region. It was not possible to establish a correlation among the types of micro-organisms and the collection sites. SIGNIFICANCE AND IMPACT OF THE STUDY: Some evidence suggests that the surface roughness of ocular prostheses can influence interactions with micro-organisms, with greater prejudicial consequences, such as the establishment of biofilms, which could lead to infections. Thus, it becomes extremely important to identify the micro-organisms present on the acrylic surfaces of ocular prostheses, as well as the microbiota of the anophthalmic cavity and contralateral eye of wearers of the same, so that subsequent control measures promote the homeostatic maintenance of the ocular region.

Natural regeneration of the herbaceous community in a semiarid region in Northeastern Brazil.

This study aimed to describe and compare the interannual changes in the diversity and population structure of herbaceous plants in an anthropogenic area that has been regenerating for 15 years and to identify the similarities and differences in the biological attributes of the community compared with the characteristics of a regenerating conserved area. In total, 105 plots measuring 1 m(2) were established. In each plot, the herbaceous plants were identified, and their height and stem diameter were measured for two consecutive years. The herbaceous flora of the anthropogenic area was represented by 86 species in 70 genera and 27 families, and there were no significant differences in the average richness between years. The conserved area was represented by 71 species in 63 genera and 35 families, and there was a significant difference in the total richness between areas and between years, except when comparing the richness between the conserved area and the anthropogenic area during the second year. Considering both the anthropogenic and conserved areas, 123 herbaceous species were listed, and the similarity between areas was 60 %. For the anthropogenic area, the floristic similarity between years was 95 %, and in the fragment of the conserved area, the similarity was 74 %. The diversity and density were significantly different between years and between areas. Given these results, this study suggests that 15 years of natural regeneration for the caatinga is not sufficient to reestablish its native flora with respect to its herbaceous component.

Survival of osseointegrated implants: a 10-year retrospective study.

Introduction: New techniques, surgical protocols, dental implant designs, and prosthetic rehabilitation have been used in dentistry, most of which have yielded good results in the literature. This retrospective survey assessed the clinical results of patients rehabilitated with dental implants between January 2011 and December 2021. Load protocols (immediate and conventional), types of connections of the installed implants, external hexagon (EH), and cone morse (MC) were evaluated. Material and methods: Two evaluators were selected and calibrated to perform the analyses. The inclusion criteria were records with complete and legible information of patients rehabilitated with dental implants who were followed for at least 1 year after rehabilita-tion. The medical records were divided into two groups, G1 (implants with conventional load) and G2 (implants with immediate load), and further subdivided according to implant type. Information about the rehabilitation failures was noted and descriptive statistics of the results were obtained. Results: Among the 432 evaluated medical records of patients rehabilitated with implants, the study included 319 records: 223 from women and 96 from men, aged 20-79 years. In total, data were available on 1,227 implants with dimensions of 10-13 mm and diameters of 3.75-4 mm. The G1 (n=1.188) survival rates were 94.95% for EH implants and 99.5% for MC implants. In G2 (n=39), the survival rates were 93.75% for EH implants and 91.3% for MC implants. The implant survival rates were relatively high among all groups evaluated; however, the discrepancy between the number of implants in the groups may compromise the comparison between them. Understanding and respecting the biomechanical and technical principles of each protocol was the main factor influencing the success of rehabilitation. Conclusion: The results of this study showed that, according to medical records, rehabilitation with dental implants showed excellent results regardless of the connection type (EH or MC) or loading protocol (conventional or immediate). The two loading protocols and two connection types had excellent results and scientific support. Therefore, the choice should be based on the clinical needs of each patient.

Antibiofilm effect of cleaning agents for ocular prostheses.

Introduction: This study aimed to evaluate the antibiofilm effect of different agents (neutral soap, 4% chlorhexidine, Efferdent effervescent tablets, 1% triclosan, and citronella essential oil) used for ocular prosthesis cleaning. Material and Methods: Biofilms of S. aureus and S. epidermidis were formed on 60 ocular prosthesis acrylic resin specimens. The specimens were cleaned with the studied agents with different techniques. Microorganism counting was performed. Data were submitted to ANOVA and HSD Tukey-Kramer (p<.01). Results: When compared to the control group, all cleaning protocols promoted a reduction in growth of microorganisms. The 4% chlorhexidine, effervescent tablets, and 1% triclosan cleaning agents eliminated biofilm in all groups. Conclusion: Therefore, immersion in 4% chlorhexidine, effervescent tablets, and 1% triclosan could be the best protocols indicated for ocular prosthesis cleaning due to their ability to eliminate biofilm.

Magnetic shielding investigation for a 6 MV in-line linac within the parallel configuration of a linac-MR system.

PURPOSE: In our current linac-magnetic resonance (MR) design, a 6 MV in-line linac is placed along the central axis of the MR's magnet where the MR's fringe magnetic fields are parallel to the overall electron trajectories in the linac waveguide. Our previous study of this configuration comprising a linac-MR SAD of 100 cm and a 0.5 T superconducting (open, split) MR imager. It showed the presence of longitudinal magnetic fields of 0.011 T at the electron gun, which caused a reduction in target current to 84% of nominal. In this study, passive and active magnetic shielding was investigated to recover the linac output losses caused by magnetic deflections of electron trajectories in the linac within a parallel linac-MR configuration. METHODS: Magnetic materials and complex shield structures were used in a 3D finite element method (FEM) magnetic field model, which emulated the fringe magnetic fields of the MR imagers. The effects of passive magnetic shielding was studied by surrounding the electron gun and its casing with a series of capped steel cylinders of various inner lengths (26.5-306.5 mm) and thicknesses (0.75-15 mm) in the presence of the fringe magnetic fields from a commercial MR imager. In addition, the effects of a shield of fixed length (146.5 mm) with varying thicknesses were studied against a series of larger homogeneous magnetic fields (0-0.2 T). The effects of active magnetic shielding were studied by adding current loops around the electron gun and its casing. The loop currents, separation, and location were optimized to minimize the 0.011 T longitudinal magnetic fields in the electron gun. The magnetic field solutions from the FEM model were added to a validated linac simulation, consisting of a 3D electron gun (using OPERA-3d/scala) and 3D waveguide (using comsol Multiphysics and PARMELA) simulations. PARMELA's target current and output phase-space were analyzed to study the linac's output performance within the magnetic shields. RESULTS: The FEM model above agreed within 1.5% with the manufacturer supplied fringe magnetic field isoline data. When passive magnetic shields are used, the target current is recoverable to greater than 99% of nominal for shield thicknesses greater than 0.75 mm. The optimized active shield which resulted in 100% target current recovery consists of two thin current rings 110 mm in diameter with 625 and 430 A-turns in each ring. With the length of the passive shield kept constant, the thickness of the shield had to be increased to achieve the same target current within the increased longitudinal magnetic fields. CONCLUSIONS: A ≥99% original target current is recovered with passive shield thicknesses >0.75 mm. An active shield consisting of two current rings of diameter of 110 mm with 625 and 430 A-turns fully recovers the loss that would have been caused by the magnetic fields. The minimal passive or active shielding requirements to essentially fully recover the current output of the linac in our parallel-configured linac-MR system have been determined and are easily achieved for practical implementation of the system.

Skin dose in longitudinal and transverse linac-MRIs using Monte Carlo and realistic 3D MRI field models.

PURPOSE: The magnetic fields of linac-MR systems modify the path of contaminant electrons in photon beams, which alters patient skin dose. To accurately quantify the magnitude of changes in skin dose, the authors use Monte Carlo calculations that incorporate realistic 3D magnetic field models of longitudinal and transverse linac-MR systems. METHODS: Finite element method (FEM) is used to generate complete 3D magnetic field maps for 0.56 T longitudinal and transverse linac-MR magnet assemblies, as well as for representative 0.5 and 1.0 T Helmholtz MRI systems. EGSnrc simulations implementing these 3D magnetic fields are performed. The geometry for the BEAMnrc simulations incorporates the Varian 600C 6 MV linac, magnet poles, the yoke, and the magnetic shields of the linac-MRIs. Resulting phase-space files are used to calculate the central axis percent depth-doses in a water phantom and 2D skin dose distributions for 70 µm entrance and exit layers using DOSXYZnrc. For comparison, skin doses are also calculated in the absence of magnetic field, and using a 1D magnetic field with an unrealistically large fringe field. The effects of photon field size, air gap (longitudinal configuration), and angle of obliquity (transverse configuration) are also investigated. RESULTS: Realistic modeling of the 3D magnetic fields shows that fringe fields decay rapidly and have a very small magnitude at the linac head. As a result, longitudinal linac-MR systems mostly confine contaminant electrons that are generated in the air gap and have an insignificant effect on electrons produced further upstream. The increase in the skin dose for the longitudinal configuration compared to the zero B-field case varies from ∼1% to ∼14% for air gaps of 5-31 cm, respectively. (All dose changes are reported as a % of D(max).) The increase is also field-size dependent, ranging from ∼3% at 20 × 20 cm(2) to ∼11% at 5 × 5 cm(2). The small changes in skin dose are in contrast to significant increases that are calculated for the unrealistic 1D magnetic field. For the transverse configuration, the entrance skin dose is equal or smaller than that of the zero B-field case for perpendicular beams. For a 10 × 10 cm(2) oblique beam the transverse magnetic field decreases the entry skin dose for oblique angles less than ±20° and increases it by no more than 10% for larger angles up to ±45°. The exit skin dose is increased by 42% for a 10 × 10 cm(2) perpendicular beam, but appreciably drops and approaches the zero B-field case for large oblique angles of incidence. CONCLUSIONS: For longitudinal linac-MR systems only a small increase in the entrance skin dose is predicted, due to the rapid decay of the realistic magnetic fringe fields. For transverse linac-MR systems, changes to the entrance skin dose are small for most scenarios. For the same geometry, on the exit side a fairly large increase is observed for perpendicular beams, but significantly drops for large oblique angles of incidence. The observed effects on skin dose are not expected to limit the application of linac-MR systems in either the longitudinal or transverse configuration.

Development of ternary and quaternary catalysts for the electrooxidation of glycerol.

This work consisted in the preparation of platinum-based catalysts supported on carbon (Vulcan XC-72) and investigation of their physicochemical and electrochemical properties. Catalysts of the C/Pt-Ni-Sn-Me (Me = Ru or Ir) type were prepared by the Pechini method at temperature of 350°C. Four different compositions were homemade: C/Pt(60)Sn(10)Ni(30), C/Pt(60)Sn(10)Ni(20)Ru(10), C/Pt(60)Sn(10)Ni(10)Ru(20), and C/Pt(60)Sn(10)Ni(10)Ir(20). These catalysts were electrochemically and physically characterized by cyclic voltammetry (CV), chronoamperometry (CA) in the presence of glycerol 1.0 mol dm(-3), X-ray diffraction (XRD), and high-resolution transmission electron microscopy (HRTEM). XRD results showed the main peaks of face-centered cubic Pt. The particle sizes obtained from XRD and HRTEM experiments were close to values ranging from 3 to 8.5 nm. The CV results indicate behavior typical of Pt-based catalysts in acid medium. The CV and CA data reveal that quaternary catalysts present the highest current density for the electrooxidation of glycerol.

Quality of life and stimulus perception in patients' rehabilitated with complete denture.

The objective of this study was to evaluate and correlate quality of life (QoL), and stimulus perception of complete denture users, before and after the insertion of new prostheses. We selected 60 patients using bimaxillary complete conventional dentures who needed to replace their prostheses. During anamnesis, we collected demographic data and applied the Oral Health Impact Profile for Edentulous Patients (OHIP-EDENT) questionnaire and stimulus perception questionnaire (PERCEPTION). Before installation of new prostheses, the patients responded to OHIP-EDENT questionnaire, and on the day of installation, they responded to PERCEPTION questionnaire. At the patients' 3-month follow-up, we re-administered the OHIP-EDENT and PERCEPTION questionnaires. The Wilcoxon and MacNemar tests were used to compare patient responses between the time points analysed. Most of the OHIP-EDENT items showed a highly significant impact of the new prostheses on oral health (P ≤ 0·003). The PERCEPTION questionnaire data indicated that the patients experienced significant improvements (P < 0·05) in terms of their sensations with the new prostheses. Cross-lagged data analysis did not show any causality between the OHIP-EDENT and PERCEPTION questionnaires (ZPF test, P = 0·772). We concluded that the treatment was effective with respect to the patients' QoL and their adaptation to the new prostheses.

Success rate of short unitary implants installed in atrophic mandible: Integrative Review.

Introduction: In the rehabilitation of total edentulous patients, lack of bone availability in posterior maxillary regions is common due to pneumatization of the maxillary sinus and posterior mandible due to the presence of the lower alveolar nerve. And to rehabilitate this type of patient, one of them is the use of short implants. Methods: The work aims to evaluate the success rate of treatment of short implants through a literature review. The search was carried out in august 2020 in the Pubmed (MedLine), Scopus and Embase databases, using the keywords: extra short implants, short implants, survival rate, single implant, atrophic mandible. The keywords followed the AND or OR criteria previously elaborated by the PICO question. The inclu-sion criteria were: implants with a length of 4 to 8 mm, which were single and in the posterior region of atrophic mandible and which had 5 years of follow-up. Articles were excluded from the review where the implants were splinted, had a follow-up of less than 5 years and considered short implants larger than 8 mm. Results: After the search, 4 articles were separated, which totaled an n = 172 short implants obtaining a success rate of 93.47% in 5 years. After the search, 4 articles were separated, which totaled an n = 172 short implants obtaining a success rate of 93.47% in 5 years. Conclusion: We can conclude that the use of short implants, even in single prostheses, has a high success rate, which can provide the edentulous patient with little bone bioavailability for rehabilitation.

Histological biomarkers and biometric data on trahira Hoplias malabaricus (Pisces, Characiformes, Erythrinidae): a bioindicator species in the Mearim river, Brazilian Amazon.

The objective of this study was to evaluate the levels of environmental contamination in a protected area in the Brazilian Amazon. For this, two areas were chosen along the Mearim River: the reference area (A1) and the potentially contaminated area (A2), where water samples were collected, for physicochemical and microbiological analyses, as well as specimens of Hoplias malabaricus, for the evaluation of biometric data and incidence of branchial lesions. The physicochemical analyzes of the water from both areas showed contamination (low levels of dissolved oxygen, tubidity and high iron concentrations, especially in A2). The microbiological analyzes showed that all water samples showed total coliform values higher than those acceptable by CONAMA and WHO (with higher values in A2), in addition to E. coli values higher than those allowed by legislation in A2. Regarding biometric data, male and female fishes were significantly longer and heavier in A1 during the dry and rain seasons and the gonadosomatic index also showed higher values in A1 than in A2 in both seasons. H. malabaricus showed gill lesions of minimal to moderate pathological importance in A1 and A2, indicating that specimens from both areas of the Mearim River showed biological responses to contamination. The observed changes in the water quality, bimetic parameters and the histological analyzes of the specimens of H. malabaricus directly reflect on the quality and health of the fishes in the Mearim River, and point to the urgent need for prevention and remediation of contamination in these ecosystems.

Matteucinol combined with temozolomide inhibits glioblastoma proliferation, invasion, and progression: an in vitro, in silico, and in vivo study.

Glioblastoma is the most prevalent and malignant brain tumor identified in adults. Surgical resection followed by radiotherapy and chemotherapy, mainly with temozolomide (TMZ), is the chosen treatment for this type of tumor. However, the average survival of patients is around 15 months. Novel approaches to glioblastoma treatment are greatly needed. Here, we aimed to investigate the anti-glioblastoma effect of the combination of matteucinol (Mat) (dihydroxyflavanone derived from Miconia chamissois Naudin) with the chemotherapeutic TMZ in vitro using tumor (U-251MG) and normal astrocyte (NHA) cell lines and in vivo using the chick embryo chorioallantoic membrane (CAM) assay. The combination was cytotoxic and selective for tumor cells (28 µg/mL Mat and 9.71 µg/mL TMZ). Additionally, the combination did not alter cell adhesion but caused morphological changes characteristic of apoptosis in vitro. Notably, the combination was also able to reduce tumor growth in the chick embryo model (CAM assay). The docking results showed that Mat was the best ligand to the cell death membrane receptor TNFR1 and to TNFR1/TMZ complex, suggesting that these two molecules may be working together increasing their potential. In conclusion, Mat-TMZ can be a good candidate for pharmacokinetic studies in view of clinical use for the treatment of glioblastoma.

Aquatic pollutants are associated with reproductive alterations and genotoxicity in estuarine fish (Sciades herzbergii - Bloch, 1794) from the Amazon Equatorial Coast.

Estuaries are constantly subject to continuous environmental impacts of human activities, such as fisheries, port or industry, and domestic sewage, with fish being one of the most affected aquatic animals, reflecting the impacts directly on their bodies. Thus, the aim of this study was to carry out the biomonitoring of an estuary located on the Amazonian Equatorial Coast through analysis of PAHs (Polycyclic Aromatic Hydrocarbons) in the water, in addition to trace metals, histopathological alterations and analysis of erythrocyte micronuclei in Sciades herzbergii. S. herzbergii was used as a model species, due to its estuarine-resident behavior. Gonad and gill samples were subjected to histopathological evaluations. The quantification of trace metals was performed in samples of skeletal muscles of the animals collected, where concentrations of Lead (Pb), Copper (Cu), Zinc (Zn), Cadmium (Cd), Magnesium (Mg), Iron (Fe) and Aluminum (Al) were found. Except for Cadmium (Cd), all the concentrations were above the recommended limits. The PAHs analysis revealed the presence of Naphthalene and Acenaphthene in the water samples Histopathological and genotoxic analyses revealed of lesions in 100% of the study specimens. Thus, the histological and genotoxic alterations found in 100% of S. herzbergii specimens captured in São José Bay-MA are potentially associated with PAH concentrations present in the water. These results are potentially associated with the presence of PAH and trace metals, both in water and in animal tissues, inferring a general scenario of environmental contamination which directly implies a risk to the health and survival of the local biota. This study shows the relevance of continuous biomonitoring of estuarine ecosystems, in order to guide authorities regarding sewage management and ensure the evolutionary development of estuarine species, especially fishes of importance in the local cuisine, therefore related to human food security.

LyeTx I, a potent antimicrobial peptide from the venom of the spider Lycosa erythrognatha.

LyeTx I, an antimicrobial peptide isolated from the venom of Lycosa erythrognatha, known as wolf spider, has been synthesised and its structural profile studied by using the CD and NMR techniques. LyeTx I has shown to be active against bacteria (Escherichia coli and Staphylococcus aureus) and fungi (Candida krusei and Cryptococcus neoformans) and able to alter the permeabilisation of L: -alpha-phosphatidylcholine-liposomes (POPC) in a dose-dependent manner. In POPC containing cholesterol or ergosterol, permeabilisation has either decreased about five times or remained unchanged, respectively. These results, along with the observed low haemolytic activity, indicated that antimicrobial membranes, rather than vertebrate membranes seem to be the preferential targets. However, the complexity of biological membranes compared to liposomes must be taken in account. Besides, other membrane components, such as proteins and even specific lipids, cannot be discarded to be important to the preferential action of the LyeTx I to the tested microorganisms. The secondary structure of LyeTx I shows a small random-coil region at the N-terminus followed by an alpha-helix that reached the amidated C-terminus, which might favour the peptide-membrane interaction. The high activity against bacteria together with the moderate activity against fungi and the low haemolytic activity have indicated LyeTx I as a good prototype for developing new antibiotic peptides.

Effect of longitudinal magnetic fields on a simulated in-line 6 MV linac.

PURPOSE: Linac-magnetic resonance (MR) systems have been proposed in order to achieve realtime image guided radiotherapy. The design of a new linac-MR system with the in-line 6 MV linac generating x-rays along the symmetry axis of an open MR imager is outlined. This new design allows for a greater MR field strength to achieve better quality images while reducing hot and cold spots in treatment planning. An investigation of linac's performance in the longitudinal fringe magnetic fields of the MR imager is given. METHODS: The open MR imager fringe magnetic field was modeled using the analytic solution of the magnetic field generated from current carrying loops. The derived solution was matched to the magnetic fringe field isolines provided for a 0.5 T open MR imager through Monte Carlo optimization. The optimized field solution was then added to the previously validated 6 MV linac simulation to quantify linac's performance in the fringe magnetic field of a 0.5 T MR imager. To further the investigation, linac's performance in large fringe fields expected from other imagers was investigated through the addition of homogeneous longitudinal fields. RESULTS: The Monte Carlo optimization of the analytic current loop solution provided good agreement with the magnetic fringe field isolines supplied by the manufacturer. The range of magnetic fields the linac is expected to experience when coupled to the 0.5 T MR imager was determined to be from 0.0022 to 0.011 T (as calculated at the electron gun cathode). The effect of the longitudinal magnetic field on the electron beam was observed to be only in the electron gun. The longitudinal field changed the electron gun optics, affecting beam characteristics, such as a slight increase in the injection current and beam diameter, and an increasingly nonlaminar transverse phase space. Although the target phase space showed little change in its energy spectrum from the altered injection phase space, a reduction in the target current and spatial distribution peak intensity was observed. Despite these changes, the target phase space had little effect on the depth dose curves or dose profiles calculated for a 40 x 40 cm2 field at 1.5 cm depth. At longitudinal fields larger than 0.012 T, a drastic reduction in the injection current from the electron gun was observed due to a large fraction of electrons striking the anode. This further reduced the target current, which reached a minimum of 28 +/- 2 mA at 0.06 T. A slow increase in the injection and target currents was observed at fields larger than 0.06 T due to greater beam collimation in the anode beam tube. CONCLUSIONS: In an effort to achieve higher quality images and a reduction in hot and cold spots in the treatment plan, a parallel configuration linac-MR system is presented. The longitudinal magnetic fields of the MR imager caused large beam losses within the electron gun. These losses may be eliminated through a redesign of the electron gun optics incorporating a longitudinal magnetic field, or through magnetic shielding, which has already been proven successful for the transverse configuration.

Feasibility of energy adaptive angular meshing for perpendicular and parallel magnetic fields in a grid based Boltzmann solver.

PURPOSE: To develop the enabling algorithmic techniques which allow forward-peaked adaptive angular meshing to be compatible with angular advection of magnetic fields within a deterministic Grid Based Boltzmann Solver (GBBS) for MRI-guided radiotherapy, and establish appropriate energy adaptive meshing schemes which minimize total numerical degrees of freedom while preserving high dosimetric accuracy for parallel and perpendicular magnetic fields. METHODS: A framework to independently adapt angular mesh resolution and basis function refinement of forward and backscattering hemispheres is developed, uniquely accommodating angular advection introduced by magnetic fields. Upwind stabilization techniques to accurately transfer fluence between hemispheres having different discretization are established. To facilitate oblique beam and magnetic field orientations, cardinal forward-peaked mesh orientations were devised to balance requirements for acyclic space-angle sweep ordering, while ensuring the beam predominantly overlaps the forward hemisphere. Energy-dependent fluence anisotropy is investigated, leading to adaptive angular meshing schemes for parallel and perpendicular magnetic fields. Calculated dose distributions were validated against GEANT4 Monte Carlo calculations on slab geometry and anthropomorphic phantoms. RESULTS: Forward-peaked and isotropic energy adaptive angular meshing schemes were developed for parallel and perpendicular magnetic fields respectively, which reduce the number of elements solved by 52.8% and 47.7% respectively compared to static discretization using 32 quadratic elements while retaining over 97% of points passing the gamma 1%/1 mm criterion against Monte Carlo. CONCLUSIONS: Techniques to preserve angular upwind-stabilization between hemispheres of a forward-peaked mesh and establish an acyclic directed space-angle sweep graph enabled energy-adaptive meshing schemes to be developed while accurately solving for magnetic fields. This substantially reduced the numerical degrees of freedom while retaining excellent dosimetric agreement with Monte Carlo. These algorithmic underpinnings contribute towards a fast deterministic GBBS for MRI-guided radiotherapy.

Effect of the Morphology of Tungsten Oxide Embedded in Sodium Alginate/Polyvinylpyrrolidone Composite Beads on the Photocatalytic Degradation of Methylene Blue Dye Solution.

Tungsten oxide nanostructures were modified by oxygen vacancies through hydrothermal treatment. Both the crystalline structure and morphological appearance were completely changed. Spherical WO3·H2O was prepared from tungstic acid solution by aging at room temperature, while rod-like WO3·0.33H2O was prepared by hydrothermal treatment of tungstic acid solution at 120 °C. These structures embedded in sodium alginate (SA)/polyvinylpyrrolidone (PVP) were synthesized as novel porous beads by gelation method into calcium chloride solution. The performance of the prepared materials as photocatalysts is examined for methylene blue (MB) degradation in aqueous solutions. Different operation parameters affecting the dye degradation process, such as light intensity, illumination time, and photocatalyst dosage are investigated. Results revealed that the photocatalytic activity of novel nanocomposite changed with the change in WO3 morphology. Namely, the beads with rod nanostructure of WO3 have shown better effectiveness in MB removal than the beads containing WO3 in spherical form. The maximum degradation efficiency was found to be 98% for WO3 nanorods structure embedded beads, while the maximum removal of WO3 nanospheres structure embedded beads was 91%. The cycling-ability and reuse results recommend both prepared structures to be used as effective tools for treating MB dye-contaminated wastewaters. The results show that the novel SA/PVP/WO3 nanocomposite beads are eco-friendly nanocomposite materials that can be applied as photocatalysts for the degradation of cationic dyes in contaminated water.