Exploiting the Physicochemical and Antimicrobial Properties of PHB/PEG and PHB/PEG/ALG-e Blends Loaded with Ag Nanoparticles.

Poly(3-hydroxybutyrate) (PHB)-based films containing Poly(ethylene glycol) (PEG), esterified sodium alginate (ALG-e) and polymeric additives loaded with Ag nanoparticles (AgNPs) were obtained by a conventional casting method. AgNPs were produced in aqueous suspension and added to polymeric gels using a phase exchange technique. Composite formation was confirmed by finding the Ag peak in the XRD pattern of PHB. The morphological analysis showed that the inclusion of PEG polymer caused the occurrence of pores over the film surface, which were overshadowed by the addition of ALG-e polymer. The PHB functional groups were dominating the FTIR spectrum, whose bands associated with the crystalline and amorphous regions increased after the addition of PEG and ALG-e polymers. Thermal analysis of the films revealed a decrease in the degradation temperature of PHB containing PEG/AgNPs and PEG/ALG-e/AgNPs, suggesting a catalytic effect. The PHB/PEG/ALG-e/AgNPs film combined the best properties of water vapor permeability and hydrophilicity of the different polymers used. All samples showed good antimicrobial activity in vitro, with the greater inhibitory halo observed for the PEG/PEG/AgNPs against Gram positive S. aureus microorganisms. Thus, the PHB/PEG/ALG-e/AgNPs composite demonstrated here is a promising candidate for skin wound healing treatment.

Structural evaluation of polymeric microbial films grown on kefir loaded with Maytenus rigida extract.

Kefir is a probiotic that has several health promising properties. Its grains can form microbial films on different types of substrates. In the present work, the surface characteristics of kefir biofilms associated with Maytenus rigida Mart. extract were minutely studied. Three different concentrations of plant extract were included in the biofilm forming solutions, where fresh grains of kefir were inoculated. The results showed that the plant extract was successfully incorporated into the exopolysaccharide matrix of the biofilm. The main chemical components found linked to the plant extract were triterpenes. The crystallinity of biofilms increased with the addition of the plant extract. The morphology revealed that at low concentrations of the extract there was a prevalence of lactobacilli, while at high concentrations yeasts were more observed. Adhesion and wettability were higher for biofilm with less extract. These results revealed that a combination of plant extract and kefir's exopolysaccharide could form biofilms with chemical and topographic properties of great interest in regenerative medicine.

Supramolecular polyelectrolyte complexes based on cyclodextrin-grafted chitosan and carrageenan for controlled drug release.

In the present study, supramolecular polyelectrolyte complexes (SPEC) based on a cyclodextrin-grafted chitosan derivative and carrageenan were prepared and evaluated for controlled drug release. Samples were characterized by FTIR, SEM, and ζ-potential measurements, which confirmed the formation of the polymeric complex. The phenolphthalein test confirmed the presence and availability of inclusion sites from the attached ßCD. Silver sulfadiazine was used as the model drug and the association with the SPEC was studied by FTIR and computational molecular modeling, using a semi-empirical method. DRS and TEM analyses have shown that Ag+ ions from the drug were reduced to form metallic silver nanostructures. In vitro tests have shown a clear bacterial activity toward Gram-positive bacteria Staphylococcus aureus and Enterococcus durans/hirae and Gram-negative bacteria Klebsiella pneumoniae and Escherichia coli. Finally, this work shows that ßCD-chitosan/carrageenan supramolecular polyelectrolyte complexes hold an expressive potential to be applied as a polymer-based system for controlled drug release.

Increased significance of food wastes: selective recovery of added-value compounds.

A single-step selective separation of two food additives was investigated using alcohol-salt aqueous two-phase systems (ATPS). The selective partitioning of two of the most used additives from a processed food waste material, vanillin and l-ascorbic acid, was successfully accomplished. The results obtained prove that alcohol-salt ATPS can be easily applied as cheaper processes for the selective recovery of valuable chemical products from food wastes and other sources. As a first approach, the phase diagrams of ATPS composed of different alcohol+inorganic salt+water were determined at 298 (± 1)K and atmospheric pressure. The influence of methanol, ethanol, 1-propanol, and 2-propanol and K(3)PO(4), K(2)HPO(4) or KH(2)PO(4)/K(2)HPO(4) in the design of the phase diagrams was addressed. After the evaluation of the phase diagrams behaviour, the influence of the phase forming constituents was assessed towards the partition coefficients and recovery percentages of vanillin and l-ascorbic acid among the coexisting phases. Both model systems and real processed food waste materials were employed. Using these ATPS as partitioning systems it is possible to recover and separate vanillin, which migrates for the alcohol-rich phase, from l-ascorbic acid, which preferentially partitions for the salt-rich phase.