Development of a rapid multiplexed assay for the direct screening of antimicrobial residues in raw milk.

Antimicrobial residues found to be present in milk can have both health and economic impacts. For these reasons, the widespread routine testing of milk is required. Due to delays with sample handling and test scheduling, laboratory-based tests are not always suited for making decisions about raw material intake and product release, especially when samples require shipping to a central testing facility. Therefore, rapid on-site screening tests that can produce results within a matter of minutes are required to facilitate rapid intake and product release processes. Such tests must be simple for use by non-technical staff. There is increasing momentum towards the development and implementation of multiplexing tests that can detect a range of important antimicrobial residues simultaneously. A simple in situ multiplexed planar waveguide device that can simultaneously detect chloramphenicol, streptomycin and desfuroylceftiofur in raw dairy milk, without sample preparation, has been developed. Samples are simply mixed with antibody prior to an aliquot being passed through the detection cartridge for 5 min before reading on a field-deployable portable instrument. Multiplexed calibration curves were produced in both buffer and raw milk. Buffer curves, for chloramphenicol, streptomycin and desfuroylceftiofur, showed linear ranges (inhibitory concentration (IC)20-IC80) of 0.1-0.9, 3-129 and 12-26 ng/ml, whilst linear range in milk was 0.13-0.74, 11-376 and 2-12 ng/ml, respectively, thus meeting European legislated concentration requirements for both chloramphenicol and streptomycin, in milk, without the need for any sample preparation. Desfuroylceftiofur-contaminated samples require only simple sample dilution to bring positive samples within the range of quantification. Assay repeatability and reproducibility were lower than 12 coefficient of variation (%CV), whilst blank raw milk samples (n = 9) showed repeatability ranging between 4.2 and 8.1%CV when measured on all three calibration curves. Graphical Abstract MBio SnapEsi reader and cartridge.

Analytical Determination of Aflatoxin in Ground Corn Check Samples Completed by Multiple Laboratories over Several Years.

Mycotoxins are toxic molecules produced by multiple fungal species, including Aspergillus and Fusarium. Fungal infection of crops can result in mycotoxins entering the animal and human food supply. Enzyme-linked immunosorbent assays and other immunological assays have been developed to detect mycotoxins in foods. To calibrate the response of those methods, reference materials with known amounts of homogeneously dispersed mycotoxins are often utilized, where the mycotoxin concentrations have been determined using high-performance liquid chromatography coupled with absorbance or fluorescence detection methods, or high-performance liquid chromatography coupled with mass spectrometry detection methods. Therefore, it is important that the analytical methods provide accurate and precise quantitation of mycotoxins. The reference materials must also contain homogeneously dispersed known quantities of mycotoxin. To evaluate the accuracy and precision of mycotoxin reference materials and the analytical methods, quantitative results from multiple laboratories were completed each year for several years on ground corn check samples containing known levels of mycotoxins. Results for the quantitation of aflatoxin-containing corn reference samples are presented in this article.

Overview of Portable Assays for the Detection of Mycotoxins, Allergens, and Sanitation Monitoring.

BACKGROUND: Many food recalls are related to the presence of undeclared allergens and microorganisms in food products. To reduce these occurrences, portable diagnostic assay kits are available to quantitate mycotoxins, to detect allergens and gluten in foods and on environmental surfaces, and for sanitation monitoring. OBJECTIVE: This article reviews diagnostic kits that can detect sources of contamination in food and ingredients as well as on surfaces and clean-in-place rinses. METHOD: Mycotoxins and gluten were detected using lateral flow diagnostic assays. Sanitation monitoring of surfaces was completed using a chemiluminescent assay to detect adenosine 5'-triphosphate disodium salt hydrate (ATP) and another assay to detect protein. RESULTS: Gluten was detected at 10 ppm in spiked commodities and on wet and dry surfaces at 2.5 µg/100cm2. Deoxynivalenol was quantitated in dry distillers grains plus solubles and mean results were within two SDs of those determined by HPLC. The chemiluminescent assay had an LOD of 6 fmol of ATP and was able to detect a 1:10 000 dilution of orange juice from surfaces. The protein assay detected 5 µg of bovine serum albumin (BSA) directly applied to the sampler, 100 µg of BSA on surfaces, and detected 1:10 dilutions of Greek yogurt and raw beef from surfaces. CONCLUSIONS: Portable diagnostic kits evaluated in this work provided accurate, rapid, and sensitive results for detection of mycotoxins, gluten, proteins, and ATP. These methods can be used in facilities with minimal training and provide results that are important to ensure food safety. HIGHLIGHTS: Portable methods to detect gluten, mycotoxins, proteins, and ATP are presented.

Comparing 2-nt 3' overhangs against blunt-ended siRNAs: a systems biology based study.

In this study, we formulate a computational reaction model following a chemical kinetic theory approach to predict the binding rate constant for the siRNA-RISC complex formation reaction. The model allowed us to study the potency difference between 2-nt 3' overhangs against blunt-ended siRNA molecules in an RNA interference (RNAi) system. The rate constant predicted by this model was fed into a stochastic simulation of the RNAi system (using the Gillespie stochastic simulator) to study the overall potency effect. We observed that the stochasticity in the transcription/translation machinery has no observable effects in the RNAi pathway. Sustained gene silencing using siRNAs can be achieved only if there is a way to replenish the dsRNA molecules in the cell. Initial findings show about 1.5 times more blunt-ended molecules will be required to keep the mRNA at the same reduced level compared to the 2-nt overhang siRNAs. However, the mRNA levels jump back to saturation after a longer time when blunt-ended siRNAs are used. We found that the siRNA-RISC complex formation reaction rate was 2 times slower when blunt-ended molecules were used pointing to the fact that the presence of the 2-nt overhangs has a greater effect on the reaction in which the bound RISC complex cleaves the mRNA.

Phosphopantetheine adenylyltransferase from Escherichia coli: investigation of the kinetic mechanism and role in regulation of coenzyme A biosynthesis.

Phosphopantetheine adenylyltransferase (PPAT) from Escherichia coli is an essential hexameric enzyme that catalyzes the penultimate step in coenzyme A (CoA) biosynthesis and is a target for antibacterial drug discovery. The enzyme utilizes Mg-ATP and phosphopantetheine (PhP) to generate dephospho-CoA (dPCoA) and pyrophosphate. When overexpressed in E. coli, PPAT copurifies with tightly bound CoA, suggesting a feedback inhibitory role for this cofactor. Using an enzyme-coupled assay for the forward-direction reaction (dPCoA-generating) and isothermal titration calorimetry, we investigated the steady-state kinetics and ligand binding properties of PPAT. All substrates and products bind the free enzyme, and product inhibition studies are consistent with a random bi-bi kinetic mechanism. CoA inhibits PPAT and is competitive with ATP, PhP, and dPCoA. Previously published structures of PPAT crystallized at pH 5.0 show half-the-sites reactivity for PhP and dPCoA and full occupancy by ATP and CoA. Ligand-binding studies at pH 8.0 show that ATP, PhP, dPCoA, and CoA occupy all six monomers of the PPAT hexamer, although CoA exhibits two thermodynamically distinct binding modes. These results suggest that the half-the-sites reactivity observed in PPAT crystal structures may be pH dependent. In light of previous studies on the regulation of CoA biosynthesis, the PPAT kinetic and ligand binding data suggest that intracellular PhP concentrations modulate the distribution of PPAT monomers between high- and low-affinity CoA binding modes. This model is consistent with PPAT serving as a "backup" regulator of pathway flux relative to pantothenate kinase.

X-ray crystal structure of Staphylococcus aureus FemA.

The latter stages of peptidoglycan biosynthesis in Staphylococci involve the synthesis of a pentaglycine bridge on the epsilon amino group of the pentapeptide lysine side chain. Genetic and biochemical evidence suggest that sequential addition of these glycines is catalyzed by three homologous enzymes, FemX (FmhB), FemA, and FemB. The first protein structure from this family, Staphylococcus aureus FemA, has been solved at 2.1 A resolution by X-ray crystallography. The FemA structure reveals a unique organization of several known protein folds involved in peptide and tRNA binding. The surface of the protein also reveals an L-shaped channel suitable for a peptidoglycan substrate. Analysis of the structural features of this enzyme provides clues to the mechanism of action of S. aureus FemA.

Determination of ligand-MurB interactions by isothermal denaturation: application as a secondary assay to complement high throughput screening.

We used a temperature-jump isothermal denaturation procedure with various methods of detection to evaluate the quality of putative inhibitors of MurB discovered by high-throughput screening. Three optical methods of detection-ultraviolet hyperchromicity of absorbance, fluorescence of bound dyes, and circular dichroism-as well as differential scanning calorimetry were used to dissect the effects of two chemical compounds and a natural substrate on the enzyme. The kinetics of the denaturation process and binding of the compounds detected by quenching of flavin fluorescence were used to quantitate the dose dependencies of the ligand effects. We found that the first step in the denaturation of MurB is the rapid loss of flavin from the active site and that the two chemical inhibitors appeared to destabilize the interaction of the cofactor with the enzyme but stabilize the global unfolding. The kinetics of the denaturation process as well as the loss of flavin fluorescence on binding established that both compounds had nanomolar affinities for the enzyme. We showed that coupling of the various detection methods with isothermal denaturation yields a powerful regimen to provide analytical data for assessing inhibitor specificity for a protein target.

Multi-selective one dimensional proton NMR experiments for rapid screening and binding affinity measurements.

High-throughput ligand-based proton NMR screening performed in the presence of a spy molecule and a control molecule is a valuable tool for identifying drug leads. A limitation of the technique is represented by the severe overlap encountered in the screening of large chemical mixtures. An approach for overcoming this overlap problem is the use of multi-selective R(1) filtered and COSY or TOCSY experiments. Application of this methodology to compounds binding to the Sudlow site I of human serum albumin is presented. The screening is performed by simply monitoring the intensity of two signals. The precise measurement of the relative intensity of the two resonances permits determination of the binding constant of the NMR-hit. For a simple competition binding mechanism, the rapidly-derived NMR binding constants are in good agreement with the values derived from full-titration ITC and fluorescence spectroscopy measurements.

The use of biochemical and biophysical tools for triage of high-throughput screening hits - A case study with Escherichia coli phosphopantetheine adenylyltransferase.

High-throughput screening is utilized by pharmaceutical researchers and, increasingly, academic investigators to identify agents that act upon enzymes, receptors, and cellular processes. Screening hits include molecules that specifically bind the target and a greater number of non-specific compounds. It is necessary to 'triage' these hits to identify the subset worthy of further exploration. As part of our antibacterial drug discovery effort, we applied a suite of biochemical and biophysical tools to accelerate the triage process. We describe application of these tools to a series of 9-oxo-4,9-dihydropyrazolo[5,1-b]quinazoline-2-carboxylic acids (PQ) hits from a screen of Escherichia coli phosphopantetheine adenylyltransferase (PPAT). Initial confirmation of specific binding to phosphopantetheine adenylyltransferase was obtained using biochemical and biophysical tools, including a novel orthogonal assay, isothermal titration calorimetry, and saturation transfer difference NMR. To identify the phosphopantetheine adenylyltransferase sub-site bound by these inhibitors, two techniques were utilized: steady-state enzyme kinetics and a novel (19)F NMR method in which fluorine-containing fragments that bind the ATP and/or phosphopantetheine sites serve as competitive reporter probes. These data are consistent with PQs binding the ATP sub-site. In addition to identification of a series of PPAT inhibitors, the described hit triage process is broadly applicable to other enzyme targets in which milligram quantities of purified target protein are available.

Thermodynamic and structure guided design of statin based inhibitors of 3-hydroxy-3-methylglutaryl coenzyme A reductase.

Clinical studies have demonstrated that statins, 3-hydroxy-3-methylglutaryl coenzyme A reductase (HMGR) inhibitors, are effective at lowering mortality levels associated with cardiovascular disease; however, 2-7% of patients may experience statin-induced myalgia that limits compliance with a treatment regimen. High resolution crystal structures, thermodynamic binding parameters, and biochemical data were used to design statin inhibitors with improved HMGR affinity and therapeutic index relative to statin-induced myalgia. These studies facilitated the identification of imidazole 1 as a potent (IC 50 = 7.9 nM) inhibitor with excellent hepatoselectivity (>1000-fold) and good in vivo efficacy. The binding of 1 to HMGR was found to be enthalpically driven with a Delta H of -17.7 kcal/M. Additionally, a second novel series of bicyclic pyrrole-based inhibitors was identified that induced order in a protein flap of HMGR. Similar ordering was detected in a substrate complex, but has not been reported in previous statin inhibitor complexes with HMGR.

Human serum albumin binding assay based on displacement of a non selective fluorescent inhibitor.

In this paper, we describe a fluorescent antibacterial analog, 6, with utility as a competition probe to determine affinities of other antibacterial analogs for human serum albumin (HSA). Analog 6 bound to HSA with an affinity of 400+/-100 nM and the fluorescence was environmentally sensitive. With 370 nm excitation, environmental sensitivity was indicated by a quenching of the 530 nm emission when the probe bound to HSA. Displacement of dansylsarcosine from HSA by 6 indicated it competed with compounds that bound at site II (ibuprofen binding site) on HSA. Analog 6 also shifted the NMR peaks of an HSA bound oleic acid molecule that itself was affected by compounds that bound at site II. In addition to binding at site II, 6 interacted at site I (warfarin binding site) as indicated by displacement of dansylamide and the shifting of NMR peaks of an HSA bound oleic acid molecule affected by warfarin site binding. Additional evidence for multiple site interaction was discovered when a percentage of 6 could be displaced by either ibuprofen or phenylbutazone. A competition assay was established using 6 to determine relative affinities of other antibacterial inhibitors for HSA.

Preparation of novel anthranilic acids as antibacterial agents: extensive evaluation of structural and physical properties on antibacterial activity and human serum albumin affinity.

In the past few years a significant effort has been devoted by Pharmacia toward the discovery of novel antibiotics. We have recently described the identification of an anthranilic acid lead 1 and the optimization resulting in the advanced lead 2. In this report, we describe the preparation of several selected analogs to probe the dependency of this template for antibacterial activity and the affinity these compounds have for human serum albumin (HSA). These analogs illustrate that decreased affinity for HSA can be achieved while retaining relevant antibacterial activity. The most important factor for reduced HSA affinity is decrease in logP rather than a structural change.

Correlation of carboxylic acid pKa to protein binding and antibacterial activity of a novel class of bacterial translation inhibitors.

Previously we reported the discovery and initial optimization of a novel anthranilic acid derived class of antibacterial agents which suffered from extensive protein binding. This report describes efforts directed toward understanding the relationship of the acidity of the carboxylic acid with the extent of protein binding. The pK(a) of the acid was modified via the synthesis of a number of anthranilic acid analogs which vary the aromatic ring substituent at the 4-position. The pK(a) and HSA binding constants have been determined for each of the analogs. Our results indicate a correlation between pK(a) and HSA K(d). The physical properties and antibacterial activities will be discussed as well as how these results help address the protein binding issue with this series of compounds.

Binding thermodynamics of substituted diaminopyrimidine renin inhibitors.

Renin is an aspartyl protease involved in the production of angiotensin II, a potent vasoconstrictor. Renin inhibitors can prevent blood vessel constriction and therefore could be useful for the treatment of hypertension. High-throughput screening efforts identified a small molecule renin inhibitor with a core substituted diaminopyrimidine ring. Parallel medicinal chemistry efforts based on this lead resulted in compound 1. A complex of 1 bound to renin was crystallized, and structural data were obtained by X-ray diffraction. The structure indicated that there were adjacent unoccupied binding pockets. Synthetic efforts were initiated to extend functionality into these pockets so as to improve affinity and adjust pharmacokinetic parameters. Thermodynamics data for inhibitor binding to renin were also collected using isothermal titration calorimetry. These data were used to help guide inhibitor optimization by suggesting molecular alterations to improve binding affinity from both thermodynamic and structural perspectives. The addition of a methoxypropyl group extending into the S3 subpocket improved inhibitor affinity and resulted in greater binding enthalpy. Initial additions to the pyrimidine ring template that extended into the large hydrophobic S2 pocket did not improve affinity and dramatically altered the thermodynamic driving force for the binding interaction. Binding of the core template was enthalpically driven, whereas binding of initial inhibitors with S2 extensions was both enthalpically and entropically driven but lost significant binding enthalpy. Additional electrostatic interactions were then incorporated into the S2 extension to improve binding enthalpy while taking advantage of the favorable entropy.

Determining molecular binding sites on human serum albumin by displacement of oleic acid.

An NMR method was developed for determining binding sites of small molecules on human serum albumin (HSA) by competitive displacement of (13)C-labeled oleic acid. This method is based on the observation that in the crystal structure of HSA complexed with oleic acid, two principal drug-binding sites, Sudlow's sites I (warfarin) and II (ibuprofen), are also occupied by fatty acids. In two-dimensional [(1)H,(13)C]heteronuclear single quantum coherence NMR spectra, seven distinct resonances were observed for the (13)C-methyl-labeled oleic acid as a result of its binding to HSA. Resonances corresponding to the major drug-binding sites were identified through competitive displacement of molecules that bind specifically to each site. Thus, binding of molecules to these sites can be followed by their displacement of oleic acids. Furthermore, the amount of bound ligand at each site can be determined from changes in resonance intensities. For molecules containing fluorine, binding results were further validated by direct observations of the bound ligands using (19)F NMR. Identifying the binding sites for drug molecules on HSA can aid in determining the structure-activity relationship of albumin binding and assist in the design of molecules with altered albumin binding.

Fluorine-NMR experiments for high-throughput screening: theoretical aspects, practical considerations, and range of applicability.

Competition ligand-based NMR screening experiments have recently been introduced to overcome most of the problems associated with traditional ligand-based NMR screening. Molecules with marginal solubility and high affinity for a given target can be easily identified in a high-throughput manner by screening chemical mixtures against the target in the presence of a weak- to medium-affinity ligand of known binding constant. While the original competition-based approaches utilized (1)H detection, significant advantages are obtained using (19)F detection. The absence of spectral overlap permits the screening of large chemical mixtures and allows for automated analysis of the spectra, even in the presence of protonated buffers, solvents, and detergents. The large chemical shift anisotropy of fluorine and the significant exchange contribution allow for the selection of a weak-affinity spy molecule, thus resulting in a lower binding affinity threshold for the identified NMR hits. The method, labeled FAXS (fluorine chemical shift anisotropy and exchange for screening) is rapid and requires only a limited amount of protein and, therefore, compares favorably with the other established non-NMR techniques used in high-throughput screening. Herein the theoretical aspects of this powerful (19)F-based approach are presented and discussed in detail. The experimental conditions together with the detection limits and binding constant measurements are investigated using human serum albumin as the target.

Identification of a mutant amyloid peptide that predominantly forms neurotoxic protofibrillar aggregates.

The amyloid peptide (Abeta), derived from the proteolytic cleavage of the amyloid precursor protein (APP) by beta- and gamma-secretases, undergoes multistage assemblies to fibrillar depositions in the Alzheimer's brains. Abeta protofibrils were previously identified as an intermediate preceding insoluble fibrils. While characterizing a synthetic Abeta variant named EV40 that has mutations in the first two amino acids (D1E/A2V), we discerned unusual aggregation profiles of this variant. In comparison of the fibrillogenesis and cellular toxicity of EV40 to the wild-type Abeta peptide (Abeta40), we found that Abeta40 formed long fibrillar aggregates while EV40 formed only protofibrillar aggregates under the same in vitro incubation conditions. Cellular toxicity assays indicated that EV40 was slightly more toxic than Abeta40 to human neuroblastoma SHEP cells, rat primary cortical, and hippocampal neurons. Like Abeta40, the neurotoxicity of the protofibrillar EV40 could be partially attributed to apoptosis since multiple caspases such as caspase-9 were activated after SHEP cells were challenged with toxic concentrations of EV40. This suggested that apoptosis-induced neuronal loss might occur before extensive depositions of long amyloid fibrils in AD brains. This study has been the first to show that a mutated Abeta peptide formed only protofibrillar species and mutations of the amyloid peptide at the N-terminal side affect the dynamic amyloid fibrillogenesis. Thus, the identification of EV40 may lead to further understanding of the structural perturbation of Abeta to its fibrillation.

Physical methods to determine the binding mode of putative ligands for hepatitis C virus NS3 helicase.

Several small molecules identified by high-throughput screening (HTS) were evaluated for their ability to bind to a nonstructural protein 3 (NS3) helicase from hepatitis C virus (HCV). Equilibrium dissociation constants (K(d)'s) of the compounds for this helicase were determined using several techniques including an assay measuring the kinetics of isothermal enzyme denaturation at several concentrations of the test molecule. Effects of two nonhydrolyzable ATP analogs on helicase denaturation were measured as controls using the isothermal denaturation (ITD) assay. Two compounds, 4-(2,4-dimethylphenyl)-2,7,8-trimethyl-4,5-quinolinediamine and 2-phenyl-N-(5-piperazin-1-ylpentyl)quinazolin-4-amine, were identified from screening that inhibited the enzyme and had low micromolar dissociation constants for NS3 helicase in the ITD assay. Low micromolar affinity of the quinolinediamine to helicase was also confirmed by nuclear magnetic resonance experiments. Unfortunately, isothermal titration calorimetry (ITC) experiments indicated that a more water-soluble analog bound to the 47/23-mer oligonucleotide helicase substrate with low micromolar affinity as did the substituted quinazolinamine. There was no further interest in these templates as helicase inhibitors due to the nonspecific binding to enzyme and substrate. A combination of physical methods was required to discern the mode of action of compounds identified by HTS and remove undesirable lead templates from further consideration.

Spontaneous aggregation and cytotoxicity of the beta-amyloid Abeta1-40: a kinetic model.

The time dependency of the spontaneous aggregation of the fibrillogenic beta-amyloid peptide, Abeta1-40, was measured by turbidity, circular dichroism, HPLC, and fluorescence polarization. The results by all methods were comparable and they were most consistent with a kinetic model where the peptide first slowly forms an activated monomeric derivative (AM), which is the only species able to initiate, by tetramerization, the formation of linear aggregates. The anti-Abeta antibody 6E10, raised against residues 1-17, at concentrations of 200-300 nM delayed significantly the aggregation of 50 microM amyloid peptide. The anti-Abeta antibody 4G8, raised against residues 17-24, was much less active in that respect, while the antibody A162, raised against the C-terminal residues 39-43 of the full-length Abeta was totally inactive at those concentrations. Concomitant with the aggregation experiments, we also measured the time dependency of the Abeta1-40-induced toxicity toward SH-EPI cells and hippocampal neurons, evaluated by SYTOX Green fluorescence, lactate dehydrogenase release, and activation of caspases. The extent of cell damage measured by all methods reached a maximum at the same time and this maximum coincided with that of the concentration of AM. According to the kinetic scheme, the latter is the only transient peptide species whose concentration passes through a maximum. Thus, it appears that the toxic species of Abeta1-40 is most likely the same transient activated monomer that is responsible for the nucleation of fibril formation. These conclusions should provide a structural basis for understanding the toxicity of Abeta1-40 in vitro and possibly in vivo.

Expression, purification, and characterization of peptidyl-tRNA hydrolase from Staphylococcus aureus.

Bacterial peptidyl-tRNA hydrolase (Pth) activity ensures the rapid recycling of peptidyl-tRNAs that result from premature termination of translation. Pth has been shown to be essential for growth in Escherichia coli suggesting that its homologue in Staphylococcus aureus is a potential molecular therapeutic target for the development of antibacterial agents. In this report we describe the cloning of a DNA fragment (573 bp) containing the pth gene from a S. aureus (strain ISP3) genomic DNA library. Analysis of the predicted polypeptide sequence from the pth gene showed that the protein shared complete conservation of the three residues thought to be involved in the active site of E. coli Pth. The gene was cloned into a pQE-60 expression vector and expressed in E. coli, and the resulting His-tagged Pth protein was purified to greater than 95% purity from the soluble portion of the E. coli lysate in a single chromatographic step. His-tagged Pth was shown to be biologically active by its ability to hydrolyze diacetyl-[(3)H]Lys-tRNA(Lys) in a time- and concentration-dependent manner. Optimum hydrolyzing activity of Pth occurred at a pH value of 7.0 and a MgCl(2) concentration of 5 mM. The K(m) of the diacetyl-[(3)H]-Lys-tRNA(Lys) substrate for S. aureus Pth was determined to be 2.8 microM. A far UV circular dichroism spectrum revealed that His-tagged S. aureus Pth appears to have a structured core predominated by beta-sheet.