Reorientation of π-conjugated molecules on few-layer MoS2 films.

Small π-conjugated organic molecules have attracted substantial attention in the past decade as they are considered as candidates for future organic-based (opto-)electronic applications. The molecular arrangement in the organic layer is one of the crucial parameters that determine the efficiency of a given device. The desired orientation of the molecules is achieved by a proper choice of the underlying substrate and growth conditions. Typically, one underlying material supports only one inherent molecular orientation at its interface. Here, we report on two different orientations of diindenoperylene (DIP) molecules on the same underlayer, i.e. on a few-layer MoS2 substrate. We show that DIP molecules adopt a lying-down orientation when deposited on few-layer MoS2 with horizontally oriented layers. In contrast, for vertically aligned MoS2 layers, DIP molecules are arranged in a standing-up manner. Employing in situ and real-time grazing-incidence wide-angle X-ray scattering (GIWAXS), we monitored the stress evolution within the thin DIP layer from the early stages of the growth, revealing different substrate-induced phases for the two molecular orientations. Our study opens up new possibilities for the next-generation of flexible electronics, which might benefit from the combination of MoS2 layers with unique optical and electronic properties and an extensive reservoir of small organic molecules.

Improved Gas Sensing Capabilities of MoS2/Diamond Heterostructures at Room Temperature.

Molybdenum disulfide (MoS2) and nanocrystalline diamond (NCD) have attracted considerable attention due to their unique electronic structure and extraordinary physical and chemical properties in many applications, including sensor devices in gas sensing applications. Combining MoS2 and H-terminated NCD (H-NCD) in a heterostructure design can improve the sensing performance due to their mutual advantages. In this study, the synthesis of MoS2 and H-NCD thin films using appropriate physical/chemical deposition methods and their analysis in terms of gas sensing properties in their individual and combined forms are demonstrated. The sensitivity and time domain characteristics of the sensors were investigated for three gases: oxidizing NO2, reducing NH3, and neutral synthetic air. It was observed that the MoS2/H-NCD heterostructure-based gas sensor exhibits improved sensitivity to oxidizing NO2 (0.157%·ppm-1) and reducing NH3 (0.188%·ppm-1) gases compared to pure active materials (pure MoS2 achieves responses of 0.018%·ppm-1 for NO2 and -0.0072%·ppm-1 for NH3, respectively, and almost no response for pure H-NCD at room temperature). Different gas interaction model pathways were developed to describe the current flow mechanism through the sensing area with/without the heterostructure. The gas interaction model independently considers the influence of each material (chemisorption for MoS2 and surface doping mechanism for H-NCD) as well as the current flow mechanism through the formed P-N heterojunction.

Lithium-Induced Reorientation of Few-Layer MoS2 Films.

Molybdenum disulfide (MoS2) few-layer films have gained considerable attention for their possible applications in electronics and optics and also as a promising material for energy conversion and storage. Intercalating alkali metals, such as lithium, offers the opportunity to engineer the electronic properties of MoS2. However, the influence of lithium on the growth of MoS2 layers has not been fully explored. Here, we have studied how lithium affects the structural and optical properties of the MoS2 few-layer films prepared using a new method based on one-zone sulfurization with Li2S as a source of lithium. This method enables incorporation of Li into octahedral and tetrahedral sites of the already prepared MoS2 films or during MoS2 formation. Our results discover an important effect of lithium promoting the epitaxial growth and horizontal alignment of the films. Moreover, we have observed a vertical-to-horizontal reorientation in vertically aligned MoS2 films upon lithiation. The measurements show long-term stability and preserved chemical composition of the horizontally aligned Li-doped MoS2.

A wide-angle X-ray scattering laboratory setup for tracking phase changes of thin films in a chemical vapor deposition chamber.

The few-layer transition metal dichalcogenides (TMD) are an attractive class of materials due to their unique and tunable electronic, optical, and chemical properties, controlled by the layer number, crystal orientation, grain size, and morphology. One of the most commonly used methods for synthesizing the few-layer TMD materials is the chemical vapor deposition (CVD) technique. Therefore, it is crucial to develop in situ inspection techniques to observe the growth of the few-layer TMD materials directly in the CVD chamber environment. We demonstrate such an in situ observation on the growth of the vertically aligned few-layer MoS2 in a one-zone CVD chamber using a laboratory table-top grazing-incidence wide-angle X-ray scattering (GIWAXS) setup. The advantages of using a microfocus X-ray source with focusing Montel optics and a single-photon counting 2D X-ray detector are discussed. Due to the position-sensitive 2D X-ray detector, the orientation of MoS2 layers can be easily distinguished. The performance of the GIWAXS setup is further improved by suppressing the background scattering using a guarding slit, an appropriately placed beamstop, and He gas in the CVD reactor. The layer growth can be monitored by tracking the width of the MoS2 diffraction peak in real time. The temporal evolution of the crystallization kinetics can be satisfactorily described by the Avrami model, employing the normalized diffraction peak area. In this way, the activation energy of the particular chemical reaction occurring in the CVD chamber can be determined.

Tuning the charge carrier mobility in few-layer PtSe2 films by Se : Pt ratio.

Recently, few-layer PtSe2 films have attracted significant attention due to their properties and promising applications in high-speed electronics, spintronics and optoelectronics. Until now, the transport properties of this material have not reached the theoretically predicted values, especially with regard to carrier mobility. In addition, it is not yet known which growth parameters (if any) can experimentally affect the carrier mobility value. This work presents the fabrication of horizontally aligned PtSe2 films using one-zone selenization of pre-deposited platinum layers. We have identified the Se : Pt ratio as a parameter controlling the charge carrier mobility in the thin films. The mobility increases more than twice as the ratio changes in a narrow interval around a value of 2. A simultaneous reduction of the carrier concentration suggests that ionized impurity scattering is responsible for the observed mobility behaviour. This significant finding may help to better understand the transport properties of few-layer PtSe2 films.

Correction: Tuning the charge carrier mobility in few-layer PtSe2 films by Se : Pt ratio.

[This corrects the article DOI: 10.1039/D1RA04507E.].

Optical Characterization of Few-Layer PtSe2 Nanosheet Films.

Thin films of transition-metal dichalcogenides are potential materials for optoelectronic applications. However, the application of these materials in practice requires knowledge of their fundamental optical properties. Many existing methods determine optical constants using predefined models. Here, a different approach was used. We determine the sheet conductance and absorption coefficient of few-layer PtSe2 in the infrared and UV-vis ranges without recourse to any particular model for the optical constants. PtSe2 samples with a thickness of about 3-4 layers were prepared by selenization of 0.5 nm thick platinum films on sapphire substrates at different temperatures. Differential reflectance was extracted from transmittance and reflectance measurements from the front and back of the sample. The film thickness, limited to a few atomic layers, allowed a thin-film approximation to calculate the optical conductance and absorption coefficient. The former has a very different energy dependence in the infrared, near-infrared, and visible ranges. The absorption coefficient exhibits a strong power-law dependence on energy with an exponent larger than three in the mid-infrared and near-infrared regions. We have not observed any evidence for a band gap in PtSe2 thin layers down to an energy of 0.4 eV from our optical measurements.

Carbide-free one-zone sulfurization method grows thin MoS2 layers on polycrystalline CVD diamond.

The last few decades faced on the fabrication of advanced engineering materials involving also different composites. Here, we report on the fabrication of few-layer molybdenum disulfide on top of thin polycrystalline diamond substrates with a high specific surface area. In the method, pre-deposited molybdenum coatings were sulfurized in a one-zone furnace at ambient pressure. As-prepared MoS2 layers were characterized by several techniques including grazing-incidence wide-angle X-ray scattering, atomic force microscopy, scanning electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy. We found out that the initial thickness of Mo films determined the final c-axis crystallographic orientation of MoS2 layer as previously observed on other substrates. Even though it is well-known that Mo diffuses into diamond at elevated temperatures, the competing sulfurization applied effectively suppressed the diffusion and a chemical reaction between molybdenum and diamond. In particular, a Mo2C layer does not form at the interface between the Mo film and diamond substrate. The combination of diamond high specific surface area along with a controllable layer orientation might be attractive for applications, such as water splitting or water disinfection.

Tuning the orientation of few-layer MoS2 films using one-zone sulfurization.

Few-layer MoS2 films are promising candidates for applications in numerous areas, such as photovoltaics, photocatalysis, nanotribology, lithium batteries, hydro-desulfurization catalysis and dry lubricants, especially due to their distinctive electronic, optical, and catalytic properties. In general, two alignments of MoS2 layers are possible - the horizontal and the vertical one, having different physicochemical properties. Layers of both orientations are conventionally fabricated by a sulfurization of pre-deposited Mo films. So far, the Mo thickness was considered as a critical parameter influencing the final orientation of MoS2 layers with horizontally and vertically aligned MoS2 grown from thin (1 nm) and thick (3 nm) Mo films, respectively. Here, we present a fabrication protocol enabling the growth of horizontally or vertically aligned few-layer MoS2 films utilizing the same Mo thickness of 3 nm. We show that the sulfur vapor is another parameter influencing the growth mechanism, where a sulfurization with higher sulfur vapor pressure leads to vertical MoS2 layers and slow sulfur evaporation results in horizontally aligned layers for a thicker Mo starting layer.