Analysis of optical core-to-core coupling: challenges and opportunities in multicore fiber amplifiers.

In this work we study in detail core-to-core coupling effects in multicore fibers (MCFs) using a simulation tool based on supermodal interference. We pay particular attention to the impact of core area scaling, which plays an important role in prospective amplifier systems. We consider geometrical and optical properties of the MCF structure, including the ability for dense packaging of the cores but also the influence on the core guidance (V-parameter). In general, this study is important to unlock the power and energy scaling potential of the next-generation MCF amplifiers.

Frequency-doubled Q-switched 4 × 4 multicore fiber laser system.

Frequency doubling of a Q-switched Yb-doped rod-type 4 × 4 multicore fiber (MCF) laser system is reported. A second harmonic generation (SHG) efficiency of up to 52% was achieved with type I non-critically phase-matched lithium triborate (LBO), with a total SHG pulse energy of up to 17 mJ obtained at 1 kHz repetition rate. The dense parallel arrangement of amplifying cores into a shared pump cladding enables a significant increase in the energy capacity of active fibers. The frequency-doubled MCF architecture is compatible with high-repetition-rate and high-average-power operation and may provide an efficient alternative to bulk solid-state systems as pump sources for high-energy titanium-doped sapphire lasers.

Mitigation of thermally-induced performance limitations in coherently-combined multicore fiber amplifiers.

Multicore fiber (MCF) amplifiers have gained increasing interest over the past years and shown their huge potential in first experiments. However, high thermal loads can be expected when operating such an amplifier at its limit. Especially in short MCF amplifiers that are pumped in counter-propagation, this leads to non-uniform mode-shrinking in the cores and, consequently, to a degradation of the system performance. In this work we show different ways to counteract the performance limitations induced by thermal effects in coherently-combined, multicore fiber amplifiers. First, we will show that pumping MCFs in co-propagation will significantly improve the combinable average power since the thermal load at the fiber end is reduced. However, this approach might not be favorable for high energy extraction. Therefore, we will introduce a new MCF design pumped in counter-propagation that leads to a reduction of the thermal load at the fiber end, which will allow for both high combined output power and pulse energy.

High-energy Q-switched 16-core tapered rod-type fiber laser system.

High-energy Q-switched master oscillator power amplifier systems based on rod-type 4 × 4 multicore fibers are demonstrated, achieving energy up to 49 mJ in ns-class pulses. A tapered fiber geometry is tested that maintains low mode order in large multimode output cores, improving beam quality in comparison to a similar fiber with no taper. The tapered fiber design can be scaled both in the number of amplifying cores and in the dimensions of the cores themselves, providing a potential route toward joule-class fiber lasers systems.

500†W rod-type 4 × 4 multicore ultrafast fiber laser.

We present a coherently combined femtosecond fiber chirped-pulse-amplification system based on a rod-type, ytterbium-doped, multicore fiber with 4 × 4 cores. A high average power of up to 500 W (after combination and compression) could be achieved at 10 MHz repetition rate with excellent beam quality. Additionally, < 500 fs pulses with up to 600 µJ of pulse energy were also realized with this setup. This architecture is intrinsically power scalable by increasing the number of cores in the fiber.

Investigation of spatiotemporal output beam profile instabilities from differentially pumped capillaries.

Differentially pumped capillaries, i.e., capillaries operated in a pressure gradient environment, are widely used for nonlinear pulse compression. In this work, we show that strong pressure gradients and high gas throughputs can cause spatiotemporal instabilities of the output beam profile. The instabilities occur with a sudden onset as the flow evolves from laminar to turbulent. Based on the experimental and numerical results, we derive guidelines to predict the onset of those instabilities and discuss possible applications in the context of nonlinear flow dynamics.

Simplified design of optical elements for filled-aperture coherent beam combination.

A simplification strategy for segmented mirror splitters (SMS) used as beam combiners is presented. These devices are useful for compact beam division and the combination of linear and 2-D arrays. However, the standard design requires unique thin-film coating sections for each input beam; thus, potential for scaling to high beam-counts is limited due to manufacturing complexity. Taking advantage of the relative insensitivity of the beam combination process to amplitude variations, numerical techniques are used to optimize highly simplified designs with only one, two or three unique coatings. It is demonstrated that with correctly chosen coating reflectivities, the simplified optics are capable of high combination efficiency for several tens of beams. The performance of these optics as beam splitters in multicore fiber amplifier systems is analyzed, and inhomogeneous power distribution of the simplified designs is noted as a potential source of combining loss in such systems. These simplified designs may facilitate further scaling of filled-aperture coherently combined systems in linear array or 2-D array formats.

Impact of thermo-optical effects in coherently combined multicore fiber amplifiers.

In this work we analyze the power scaling potential of amplifying multicore fibers (MCFs) used in coherently combined systems. In particular, in this study we exemplarily consider rod-type MCFs with 2 × 2 up to 10 × 10 ytterbium-doped cores arranged in a squared pattern. We will show that, even though increasing the number of active cores will lead to higher output powers, particular attention has to be paid to arising thermal effects, which potentially degrade the performance of these systems. Additionally, we analyze the influence of the core dimensions on the extractable and combinable output power and pulse energy. This includes a detailed study on the thermal effects that influence the propagating transverse modes and, in turn, the amplification efficiency, the combining efficiency, the onset of nonlinear effect, as well as differences in the optical path lengths between the cores. Considering all these effects under rather extreme conditions, the study predicts that average output powers higher than 10 kW from a single 1 m long ytterbium-doped MCF are feasible and femtosecond pulses with energies higher than 400 mJ can be extracted and efficiently recombined in a filled-aperture scheme.

Transverse single-mode operation in a passive large pitch fiber with more than 200 µm mode-field diameter.

In this Letter, we present, to the best of our knowledge, the largest effective single-mode fiber reported to date. The employed waveguide is a passive large pitch fiber (LPF), which shows the core area scaling potential of such a fiber structure. In particular, we achieved stable single-transverse mode transmission at a wavelength of 1.03 µm through a straight passive LPF with a pitch of 140 µm, resulting in a measured mode-field diameter of 205 µm.

3.5 kW coherently combined ultrafast fiber laser.

An ultrafast laser based on the coherent beam combination of four ytterbium-doped step-index fiber amplifiers is presented. The system delivers an average power of 3.5 kW and a pulse duration of 430 fs at an 80 MHz repetition rate. The beam quality is excellent (M2<1.24·1.10), and the relative intensity noise is as low as 1% in the frequency span from 1 Hz to 1 MHz. The system is turn-key operable, as it features an automated spatial and temporal alignment of the interferometric amplification channels.