Broken-gap energy alignment in two-dimensional van der Waals heterostructures for multifunctional tunnel diodes.

Two-dimensional (2D) materials are promising platforms for future nanoelectronic technologies as they provide the building blocks for atomically thin devices, including switches, amplifiers, and oscillators. When 2D materials are layered on top of each other, forming van der Waals heterostructures (vdWHs), they can provide unique properties not possessed by the individual layers. Here we consider the vdWHs HfS2/MoTe2, HfS2/WTe2, 1T-HfS2/WTe2, TiS2/WSe2, TiS2/ZnO, and TiSe2/WTe2 as potential Esaki (or tunnel) diodes that can be incorporated into electronic devices. In this work, the strongly constrained and appropriately normed (SCAN) meta-generalised-gradient approximation (meta-GGA) functional is employed for the structural properties, whereas the Heyd-Scuseria-Ernzerhof (HSE) functional is used for the electronic properties. We establish that the band alignments in these systems form broken-band heterojunctions. We show that the electronic properties of the systems can be effectively modulated by applying lateral strain or an external electric field. Importantly, we demonstrate that the band gap of the vdWHs can be widened by up to 0.65 eV by applying an electric force field of -1 to +1 eV Å-1. This work demonstrates a set of 6 vdWHs with properties suitable for application as 2D Esaki tunnel diodes, 4 of which could be applied as multifunctional devices. These materials not only offer new device properties, but their small dimensions allow for the creation of ultrathin devices.

A case study using spectroscopy and computational modelling for Co speciation in a deep eutectic solvent.

Cobalt has a vital role in the manufacturing of reliable and sustainable clean energy technologies. However, the forecasted supply deficit for cobalt is likely to reach values of 150 kT by 2030. Therefore, it is paramount to consider end-of-life devices as secondary resources for cobalt. Electrorecovery of cobalt from leached solutions has attracted attention due to the sustainability of the recovery process over solvent extraction followed by chemical precipitation. Recently, we reported Co electrorecovery from two different cobalt sources (CoCl2·6H2O and CoSO4·7H2O) using ethylene glycol : choline chloride (EG : ChCl) in a 4.5 : 1 molar ratio, leading to higher purity and easier electrodeposition when sulfate was present as an additive. Here, Co2+ speciation is reported for the two EG : ChCl systems depending on the cobalt source using several spectroscopic techniques (e.g. NMR, EPR, FTIR) in combination with molecular dynamics simulations. Monodentate coordination of SO42- to Co2+, forming the tetrahedral [CoCl3(SO4)]3- was observed as the dominant structure in the system containing CoSO4·7H2O, whereas the system comprising CoCl2·6H2O shows a homoleptic tetrahedral [CoCl4]2- as the dominant structure. This resulted in knowledge being gained regarding Co2+ speciation and the correlation with electrochemistry will contribute to the science required for designing safe electrolytes for efficient electrorecovery.

Ferroelectric van der Waals heterostructures of CuInP2S6for non-volatile memory device applications.

Two-dimensional (2D) ferroelectric materials are providing promising platforms for creating future nano- and opto-electronics. Here we propose new hybrid van der Waals heterostructures, in which the 2D ferroelectric material CuInP2S6(CIPS) is layered on a 2D semiconductor for near-infrared (NIR) memory device applications. Using density functional theory, we show that the band gap of the hybrid bilayers formed with CIPS can be tuned and that the optical and electronic properties can be successfully modulated via ferroelectric switching. Of the 3712 heterostructures considered, we identified 19 structures that have a type II band alignment and commensurate lattice matches. Of this set, both the CuInP2S6/PbSe and CuInP2S6/Ge2H2heterostructures possess absorption peaks in the NIR region that change position and intensity with switching polarisation, making them suitable for NIR memory devices. The CuInP2S6/ISSb, CuInP2S6/ISbSe, CuInP2S6/ClSbSe and CuInP2S6/ZnI2heterostructures had band gaps which can be switched from direct to indirect with changing the polarisation of CIPS making them suitable for optoelectronics and sensors. The heterostructures formed with CIPS are exciting candidates for stable ferroelectric devices, opening a pathway for tuning the band alignment of van der Waal heterostructures and the creation of modern memory applications that use less energy.

Photochemical Etching of Carbonyl Groups from a Carbon Matrix: The (001) Diamond Surface.

The surface of diamond is reported to undergo nonablative photochemical etching when exposed to ultraviolet (UV) radiation which allows controlled single and partial layer removal of lattice layers. Oxygen termination of surface dangling bonds is known to be crucial for the etching process; however, the exact mechanism of carbon ejection remains unclear. We investigate the interaction of UV laser pulses with oxygen-terminated diamond surfaces using atomic-scale surface characterization combined with first-principles time-dependent density functional theory calculations. We present evidence for laser-induced desorption (LID) from carbonyl functional groups at the diamond {001} surface. The doubly bonded carbonyl group is photoexcited into a triply bonded CO-like state, including scission of the underlying C─C bonds. The carbon removal process in LID is atom by atom; therefore, this mechanism provides a novel "top-down" approach for creating nanostructures on the surface of diamond and other carbon-containing semiconductors.

Tuning the work function of the silicene/4 × 4 Ag(111) surface.

Silicene, the silicon analog of graphene, is an atomically thin two-dimensional material with promising applications in gas sensing, storage and as components in modern electronic devices. Silicene epitaxially grown on the Ag(111) surface can expand the utility of the silver surface by enabling the tuning of its work function through the functionalisation of silicene. Here we examine the electronic and structural properties and the thermodynamic stability of functionalised silicene/4 × 4 Ag(111) using density functional theory calculations coupled with ab initio molecular dynamics (AIMD) simulations. We focus on 11 functional groups, namely phenyl, methyl, hydroxyl, cyano, methoxyl, amino and ethylmethylamine, in addition to 4 halogen atoms. These functional groups are shown to endow the Si/Ag(111) surface with a large variation in the work function. Our AIMD simulations confirm the thermodynamic stability of these 11 functionalised structures. This work shows the possibility of tuning the electronic structure of silicene by functionalisation, which could then be utilized in polymer solar cells and nanoelectronic circuit components.

Adsorption of toxic gases on silicene/Ag(111).

Silicene is a two-dimensional nanomaterial, composed of Si atoms arranged into a buckled honeycomb network. It has become of great interest in recent years due to its remarkable properties such as its natural compatibility with current silicon-based technology. Due to its extreme thinness on the nanoscale, and large lateral dimensions, it has potential applications in gas sensing, gas storage and components in modern electronic devices. In this work, density functional theory calculations and ab initio molecular dynamics simulations are used to examine the reaction of SO2, NO2 and H2S on the Si/Ag(111) surface. It was shown that each gas will adsorb on the surface in different orientations and adsorption sites. SO2 and NO2 were found to chemisorb on the surface, whereas H2S was found to physisorb. SO2 and H2S adsorb associatively, whereas NO2 readily dissociates, producing adsorbed oxygen, and gaseous NO. At elevated temperatures, the SO2 and NO2 remain strongly bound to the surface, resulting in poisoning of the silicene, while H2S readily desorbs. Ab initio molecular dynamics also show that NO2 will selectively bind before SO2 when both gases are present in the same environment. This work shows that Si/Ag(111) may provide useful properties for gas sensing and storage applications.

Electronic transport investigation of redox-switching of azulenequinones/hydroquinones via first-principles studies.

The redox switching of non-alternant azulenequinone/hydroquinone molecules is investigated using density functional theory and the nonequilibrium Green's function. We examined the electronic transport properties of these molecules when subtended between gold electrodes. The results indicated that the reduction of 1,5-azulenequinone and oxidation of 1,7-azulene hydroquinone 2,6-dithiolate lead to a significant enhancement of the current compared to the respective oxidation of 1,5-azulene hydroquinone and reduction of 1,7-azulenequinone, thus "switching on" the transmission. The significance of the position of the functional group on the switching behavior has been analyzed and whether destructive quantum interference exists in the electron transport of the 1,5 position in particular has been addressed. Our work provides theoretical foundations for organic redox switching components in nanoelectronic circuits.

Magnetic properties of stoichiometric and defective Co9S8.

In this paper, we present a detailed study of the stoichiometric and reduced Co9S8 pentlandite magnetic properties, based on density functional theory. We analyze both its geometry and electronic properties and show that only by the inclusion of the Hubbard term it is possible to correctly describe d-d splitting, which is necessary to accurately characterize the Co9S8 spin configuration and its antiferromagnetic nature. We also analyze the effect of sulfur vacancies and predict the formation of ferromagnetic clusters that give local ferromagnetic character to non-stoichiometric Co9S8, which may explain the contradictory experimental results reported in the literature.

Superconductivity in intercalated buckled two-dimensional materials: KGe2.

Germanene has emerged as a novel two-dimensional material with various interesting properties and applications. Here we report the possibility of superconductivity in a stable potassium intercalated germanene compound, KGe2, with a transition temperature Tc ∼ 11 K, and an electron-phonon coupling of 1.9. Applying a 5% tensile strain, which reduces the buckling height by 4.5%, leads to the reduction of the electron-phonon coupling by 11% and a slight increase in Tc ∼ 12 K. That is, strong electron-phonon coupling results from the buckled structure of the germanene layers. Despite being an intercalated van der Waals material similar to intercalated graphite superconductors, it does not possess an occupied interlayer state.

Electrocatalytic Activity of a 2D Phosphorene-Based Heteroelectrocatalyst for Photoelectrochemical Cells.

Research into efficient synthesis, fundamental properties, and potential applications of phosphorene is currently the subject of intense investigation. Herein, solution-processed phosphorene or few-layer black phosphorus (FL-BP) sheets are prepared using a microwave exfoliation method and used in photoelectrochemical cells. Based on experimental and theoretical (DFT) studies, the FL-BP sheets are found to act as catalytically active sites and show excellent electrocatalytic activity for triiodide reduction in dye-sensitized solar cells. Importantly, the device fabricated based on the newly designed cobalt sulfide (CoSx ) decorated nitrogen and sulfur co-doped carbon nanotube heteroelectrocatalyst coated with FL-BP (FL-BP@N,S-doped CNTs-CoSx ) displayed an impressive photovoltaic efficiency of 8.31 %, outperforming expensive platinum based cells. This work paves the way for using phosphorene-based electrocatalysts for next-generation energy-storage systems.

Are dispersion corrections accurate outside equilibrium? A case study on benzene.

Modern approaches to modelling dispersion forces are becoming increasingly accurate, and can predict accurate binding distances and energies. However, it is possible that these successes reflect a fortuitous cancellation of errors at equilibrium. Thus, in this work we investigate whether a selection of modern dispersion methods agree with benchmark calculations across several potential-energy curves of the benzene dimer to determine if they are capable of describing forces and energies outside equilibrium. We find the exchange-hole dipole moment (XDM) model describes most cases with the highest overall agreement with reference data for energies and forces, with many-body dispersion (MBD) and its fractionally ionic (FI) variant performing essentially as well. Popular approaches, such as Grimme-D and van der Waals density functional approximations (vdW-DFAs) underperform on our tests. The meta-GGA M06-L is surprisingly good for a method without explicit dispersion corrections. Some problems with SCAN+rVV10 are uncovered and briefly discussed.

TDDFT Study of the Optical Excitation of Nucleic Acid Bases-C60 Complexes.

The potential of C60 as a nucleic acid base (NAB) optical sensor is theoretically explored. We investigate the adsorption of four NABs, namely, adenine, cytosine, guanine, and thymine, on C60 in the gas phase. For the optimal NAB@C60 adsorption configurations, obtained using a dispersion-corrected density functional, we calculate the vis-near-ultraviolet optical response using time-dependent density functional theory. While the isolated C60 and NAB molecules do not exhibit visible optical excitation, we find that C60/NAB conjugation gives rise to distinct spectral features in the visible range. These results suggest that C60 conjugation can be applied for photodetection of individual NABs.

Endohedral metallofullerenes, M@C60 (M = Ca, Na, Sr): selective adsorption and sensing of open-shell NOx gases.

Based on density-functional theory and non-equilibrium Green's function calculations, we demonstrate that endohedral metallofullerenes (EMFs) are reactive to open-shell gases, and therefore have the potential application as selective open-shell gas sensors. The adsorption of eight gas species (CO, H2O, H2S, NO2, NO, SO2, O2 and NH3) on three EMFs (M@C60, M = Ca, Na and Sr) shows that the adsorption energies of the EMFs towards NO2 and NO are significantly higher than the closed-shell species. Moreover, the high selectivity appears relatively insensitive to the inserted metal atoms. The calculated current-voltage characteristics of gold-M@C60-gold structures (M = Ca, Na) show that the adsorption of NO2 leads to significant change in conductivity, suggesting a potential application as an EMF gas resistive sensing device.

Large spin-filtering effect in Ti-doped defective zigzag graphene nanoribbon.

Through first-principles calculations using the nonequilibrium Green's function formalism together with density functional theory, we study the conductance of double-vacancy zigzag graphene nanoribbons doped with four transition metal atoms Ti, V, Cr and Fe. We show that Ti doping induces large spin-filtering with an efficiency in excess of 90% for bias voltages below 0.5 V, while the other metal adatoms do not induce large spin filtering. This is despite the fact that the Ti dopant possesses small spin moment, while large moments reside on V, Cr and Fe dopants. Our analysis shows that the suppression of transmission in the spin-down channel in the Ti-doped graphene nanoribbon, thus the large spin filtering efficiency, is due to transmission anti-resonance arising from destructive quantum interference. These findings suggest that the decoration of graphene with titanium, and possibly other transition metals, can act as effective spin filters for nanospintronic applications.

Communication: Electrical rectification of C59N: The role of anchoring and doping sites.

Based on the nonequilibrium Green's function formalism and density-functional theory, we investigate the onset of electrical rectification in a single C59N molecule in conjunction with gold electrodes. Our calculations reveal that rectification is dependent upon the anchoring of the Au atom on C59N; when the Au electrode is singly bonded to a C atom (labeled here as A), the system does not exhibit rectification, whereas when the electrode is connected to the C-C bridge site between two hexagonal rings (labeled here as B), transmission asymmetry is observed, where the rectification ratio reaches up to 2.62 at ±1 V depending on the N doping site relative to the anchoring site. Our analysis of the transmission mechanism shows that N doping of the B configuration causes rectification because more transmission channels are available for transmission in the B configuration than in the A configuration.

Frustrated van der Waals heterostructures.

Geometrical frustration results from the packing of constituents in a lattice, where the constituents have conflicting forces. The phenomenon is known in glass materials, and this work expands the concept of geometrical frustration into the realm of van der Waals two-dimensional materials. Using density functional theory with the r2SCAN + rVV10 exchange-correlation potential, we find a number of two-dimensional heterostructures with alternating strains, where one layer is strained and the adjacent layer is compressed. We adopted three structural stability criteria to find synthesisable candidate materials: phonon dispersion of the individual layers, comparing the thermodynamic stability of this class of materials, frustrated van der Waals heterostructures, with the non-frustrated counterparts, and ab initio molecular dynamics simulations. These criteria were applied to 7 frustrated van der Waals heterostructures, identifying one material that is potentially stable. We discuss possible fabrication pathways for creating this class of materials.

Improving sensing of formaldehyde using ZnO nanostructures with surface-adsorbed oxygen.

Detection of pollutant gases, such as formaldehyde (HCHO), in our homes and surrounding environment is of high importance for our health and safety. The effect of surface defects and specifically pre-adsorbed oxygen on the gas sensing reaction of HCHO with ZnO nanostructures is largely unknown. Using density functional theory, nonequilibrium Green's function method and ab initio molecular dynamics (AIMD) simulations, we show that the presence of surface oxygen has two key roles in the sensitivity of ZnO towards HCHO: (1) it leads to the presence of charge trap states, which vanish upon the adsorption of HCHO, and (2) it facilitates the dissociative chemisorption of HCHO on the surface. Our ground state and AIMD calculations show that multiple reaction products are produced, which eventually lead to cleaning the surface from the adsorbed species, and hence enhancing the recyclability of the surface. We not only confirm the reaction proposed by experiment, but show that the presence of surface oxygen facilitates other surface reactions as well. Our work provides insights into the gas-surface reaction mechanism of ZnO-nanostructure based gas sensors, not provided before by experiment.

Naturally-meaningful and efficient descriptors: machine learning of material properties based on robust one-shot ab initio descriptors.

Establishing a data-driven pipeline for the discovery of novel materials requires the engineering of material features that can be feasibly calculated and can be applied to predict a material's target properties. Here we propose a new class of descriptors for describing crystal structures, which we term Robust One-Shot Ab initio (ROSA) descriptors. ROSA is computationally cheap and is shown to accurately predict a range of material properties. These simple and intuitive class of descriptors are generated from the energetics of a material at a low level of theory using an incomplete ab initio calculation. We demonstrate how the incorporation of ROSA descriptors in ML-based property prediction leads to accurate predictions over a wide range of crystals, amorphized crystals, metal-organic frameworks and molecules. We believe that the low computational cost and ease of use of these descriptors will significantly improve ML-based predictions.

Blocking Directional Lithium Diffusion in Solid-State Electrolytes at the Interface: First-Principles Insights into the Impact of the Space Charge Layer.

Understanding the degradation mechanisms in solid-state lithium-ion batteries at interfaces is fundamental for improving battery performance and for designing recycling methodologies for batteries. A key source of battery degradation is the presence of the space charge layer at the solid-state electrolyte-electrode interface and the impact that this layer has on the thermodynamics of the electrolyte structure. Currently, Li10GeP2S12 in its pristine form has one of the highest lithium conductivities and has been used as a template for designing even higher conductivity derived structures. However, being an ionic material with mostly linear diffusion, it is prone to path-blocker defects, which we show here to be especially prevalent in the space charge layer. We analyze the thermodynamic properties of a number of path-blocker defects using density functional theory and their potential crystal decomposition and find that the presence of an electrostatic potential in the space charge layer elevates the likelihood of existence of these defects, which otherwise would not be likely to form in the bulk of the electrolyte away from electrodes. We use ab initio molecular dynamics to assess the impact of these defects on the diffusivity of the crystal and find that they all reduce the lithium diffusivity. While our work focuses on Li10GeP2S12, it is relevant to any solid-state electrolyte with mainly linear diffusion.

Tuning the Schottky barrier height in a multiferroic In2Se3/Fe3GeTe2 van der Waals heterojunction.

The ferroelectric material In2Se3 is currently of significant interest due to its built-in polarisation characteristics that can significantly modulate its electronic properties. Here we employ density functional theory to determine the transport characteristics at the metal-semiconductor interface of the two-dimensional multiferroic In2Se3/Fe3GeTe2 heterojunction. We show a significant tuning of the Schottky barrier height as a result of the change in the intrinsic polarisation state of In2Se3: the switching in the electric polarisation of In2Se3 results in the switching of the nature of the Schottky barrier, from being n-type to p-type, and is accompanied by a change in the spin polarisation of the electrons. This switchable Schottky barrier structure can form an essential component in a two-dimensional field effect transistor that can be operated by switching the ferroelectric polarisation, rather than by the application of strain or electric field. The band structure and density of state calculations show that Fe3GeTe2 lends its magnetic and metallic characteristics to the In2Se3 layer, making the In2Se3/Fe3GeTe2 heterojunction a potentially viable multiferroic candidate in nanoelectronic devices like field-effect transistors. Moreover, our findings reveal a transfer of charge carriers from the In2Se3 layer to the Fe3GeTe2 layer, resulting in the formation of an in-built electric field at the metal-semiconductor interface. Our work can substantially broaden the device potential of the In2Se3/Fe3GeTe2 heterojunction in future low-energy electronic devices.