RESUMO
Kingham [(1982). The post-ionization of field evaporated ions: A theoretical explanation of multiple charge states. Surf Sci116(2), 273-301] provided equations for the probability of observing higher charge states in atom probe tomography (APT) experiments. These "Kingham curves" have wide application in APT, but cannot be analytically transformed to provide the electric field in terms of the easily measured charge state ratio (CSR). Here we provide a numerical scheme for the calculation of Kingham curves and the variation in electric field with CSR. We find the variation in electric field with CSR is well described by a simple two- or three-parameter equation, and the model is accurate to most elements and charge states. The model is applied to experimental APT data of pure aluminium and a microalloyed steel, demonstrating that the methods described in this work can be easily applied to a variety of APT problems to understand electric field variations.
RESUMO
There has been an increasing interest in atom probe tomography (APT) to characterize hydrated and biological materials. A major benefit of APT compared to microscopy techniques more commonly used in biology is its combination of outstanding three-dimensional (3D) spatial resolution and mass sensitivity. APT has already been successfully used to characterize biominerals, revealing key structural information at the atomic scale, however there are many challenges inherent to the analysis of soft hydrated materials. New preparation protocols, often involving specimen preparation and transfer at cryogenic temperature, enable APT analysis of hydrated materials and have the potential to enable 3D atomic scale characterization of biological materials in the near-native hydrated state. In this study, samples of pure water at the tips of tungsten needle specimens were prepared at room temperature by graphene encapsulation. A comparative study was conducted where specimens were transferred at either room temperature or cryo-temperature and analyzed by APT by varying the flight path and pulsing mode. The differences between the analysis workflows are presented along with recommendations for future studies, and the compatibility between graphene coating and cryogenic workflows is demonstrated.
RESUMO
The application of atom probe tomography (APT) to frozen liquids is limited by difficulties in specimen preparation. Here, we report on the use of nanoporous Cu needles as a physical framework to hold water ice for investigation using APT. Nanoporous Cu needles are prepared by electropolishing and dealloying Cu-Mn matchstick precursors. Cryogenic scanning electron microscopy and focused ion beam milling reveal a hierarchical, dendritic, highly wettable microstructure. The atom probe mass spectrum is dominated by peaks of Cu+ and H(H2O)n+ up to n ≤ 3, and the reconstructed volume shows the protrusion of a Cu ligament into an ice-filled pore. The continuous Cu ligament network electrically connects the apex to the cryostage, leading to an enhanced electric field at the apex and increased cooling, both of which simplify the mass spectrum compared to previous reports.
RESUMO
In order to advance plasmon-based technologies, new materials with low damping losses and high chemical stability are needed. In this letter, we report the bulk scale fabrication of sodium tungsten bronze (Na x WO3) nanoparticles with high Na content (x ≤ 0.83) using a furnace-assisted method. Phase purity and morphology is confirmed with x-ray diffraction and scanning electron microscopy. Plasmon responses are characterized using spectrophotometry and spatially-resolved electron energy-loss spectroscopy (EELS) in a scanning transmission electron microscope. Experimental EELS maps of individual nanoparticles show the excitation of distinct plasmon resonances at visible and near-infrared (NIR) frequencies, and these observations are supported by boundary element method simulations. Na x WO3 is a promising alternative material for plasmonics due to its strong plasmon resonances when compared to Au, its simple nanofabrication, and low cost. In particular, their high NIR extinction makes these materials ideal for applications in solar control window coatings or plasmonic photocatalysis.
RESUMO
Conventional electrodes and electrocatalysts possess complex compositional and structural motifs that impact their overall electrochemical activity. These motifs range from defects and crystal orientation on the electrode surface to layers and composites with other electrode components, such as binders. Therefore, it is vital to identify how these individual motifs alter the electrochemical activity of the electrode. Scanning electrochemical cell microscopy (SECCM) is a powerful tool that has been developed for investigating the electrochemical properties of complex structures. An example of a complex electrode surface is Zn-Al alloys, which are utilized in various sectors ranging from cathodic protection of steel to battery electrodes. Herein, voltammetric SECCM and correlative microstructure analysis are deployed to probe the electrochemical activities of a range of microstructural features, with 651 independent voltammetric measurements made in six distinctive areas on the surface of a Zn-Al alloy. Energy-dispersive X-ray spectroscopy (EDS) mapping reveals that specific phases of the alloy structure, particularly the α-phase Zn-Al, favor the early stages of metal dissolution (i.e., oxidation) and electrochemical reduction processes such as the oxygen reduction reaction (ORR) and redeposition of dissolved metal ions. A correlative analysis performed by comparing high-resolution quantitative elemental composition (i.e., EDS) with the corresponding spatially resolved cyclic voltammograms (i.e., SECCM) shows that the nanospot α-phase of the Zn-Al alloy contains high Al content (30-50%), which may facilitate local Al dissolution as the local pH increases during the ORR in unbuffered aqueous media. Overall, SECCM-based high-throughput electrochemical screening, combined with microstructure analysis, conclusively demonstrates that structure-composition heterogeneity significantly influences the local electrochemical activity on complex electrode surfaces. These insights are invaluable for the rational design of advanced electromaterials.
RESUMO
The CAMECA Invizo 6000 atom probe microscope uses ion optics that differ significantly from the local electrode atom probe (LEAP). It uses dual antiparallel deep ultraviolet lasers, a flat counter electrode, and a series of accelerating and decelerating lenses to increase the field-of-view of the specimen without reducing the mass resolving power. In this work we characterise the performance of the Invizo 6000 using three material case studies: a model Al-Mg-Si alloy, a commercially-available Ni-based superalloy, and a Zr alloy, using a combination of air and vacuum-transfer between instruments. The ion optics of the Invizo 6000 significantly increase the field-of-view compared to the same specimen on a LEAP 4000 X Si. We also observe a significant increase in specimen yield, especially for the Zr alloy. These results combine to make the Invizo 6000 well-suited to research projects requiring large analysis volumes, particularly so for traditionally difficult samples such as oxides.
RESUMO
The sodium tungsten bronzes (NaxWO3) are sub-stoichiometric metal oxides with variable Na content described by x. Methods to determine the overall x of a sample are well-known, but variations of composition within a particle have not yet been explored. In this work, electron microscopy techniques are used to determine the crystallinity and chemical composition of individual Na0.83WO3 nanocubes. The particles are found to be single crystals, with the top and bottom faces of the nanocubes parallel to the {100} planes. Compositional homogeneity is observed within the particles other than an approximately ≈5â¯nm Na-depletion layer at the edge of the particle. An O-depleted layer, believed to be the result of beam damage, is observed when the beam is scanned slowly over the edge of the particle. Calculations of the plasmon responses using the boundary element method (BEM) show that this depletion layer has a minor impact on the optical properties of the large (190â¯nm) particle studied of this work, but is expected to have a dramatic impact for small (20â¯nm) particles.