Photonic lantern broadband orbital angular momentum mode multiplexer.

Optical vortex beams that carry orbital angular momentum (OAM), also known as OAM modes, have attracted considerable interest in recent years as they can comprise an additional degree of freedom for a variety of advanced classical and quantum optical applications. While canonical methods of OAM mode generation are effective, a method that can simultaneously generate and multiplex OAM modes with low loss and over broad spectral range is still in great demand. Here, via novel design of an optical fiber device referred to as a photonic lantern, where the radial mode index ("m") is neglected, for the first time we demonstrate the simultaneous generation and multiplexing of OAM modes with low loss and over the broadest spectral range to date (550 nm). We further confirm the potential of this approach to preserve the quality of studied OAM modes by fusion splicing the end-facet of the fabricated device to a delivery ring-core fiber (RCF).

Investigation of bandwidth loading in optical fibre transmission using amplified spontaneous emission noise.

The use of spectrally shaped amplified spontaneous emission noise (SS-ASE) as a method for emulating interfering channels in optical fibre transmission systems has been studied. It is shown that the use of SS-ASE leads to a slightly pessimistic performance relative to the use of conventionally modulated interfering channels in the nonlinear regime. The additional nonlinear interference noise (on the channel under test), due to the Gaussian nature of SS-ASE, has been calculated using a combination of the Gaussian noise (GN) and enhanced GN (EGN) models for the entire C-band (4.5 THz) and experimentally shown to provide a lower bound for transmission performance.

Comparison of digital signal-signal beat interference compensation techniques in direct-detection subcarrier modulation systems.

Single-polarization direct-detection transceivers may offer advantages compared to digital coherent technology for some metro, back-haul, access and inter-data center applications since they offer low-cost and complexity solutions. However, a direct-detection receiver introduces nonlinearity upon photo detection, since it is a square-law device, which results in signal distortion due to signal-signal beat interference (SSBI). Consequently, it is desirable to develop effective and low-cost SSBI compensation techniques to improve the performance of such transceivers. In this paper, we compare the performance of a number of recently proposed digital signal processing-based SSBI compensation schemes, including the use of single- and two-stage linearization filters, an iterative linearization filter and a SSBI estimation and cancellation technique. Their performance is assessed experimentally using a 7 × 25 Gb/s wavelength division multiplexed (WDM) single-sideband 16-QAM Nyquist-subcarrier modulation system operating at a net information spectral density of 2.3 (b/s)/Hz.

High spectral density transmission emulation using amplified spontaneous emission noise.

We demonstrate the use of spectrally shaped amplified spontaneous emission (SS-ASE) noise for wideband channel loading in the investigation of nonlinear transmission limits in wavelength-division multiplexing transmission experiments using Nyquist-spaced channels. The validity of this approach is explored through statistical analysis and experimental transmission of Nyquist-spaced 10 GBaud polarization-division multiplexing (PDM) quadrature phase-shift keying and PDM-16-ary quadrature amplitude modulation (QAM) channels, co-propagated with SS-ASE over single mode fiber. It is shown that this technique, which is simpler to implement than a fully modulated comb of channels, is valid for distances exceeding 240 km for PDM-16QAM with dispersion of 16 ps/nm/km, yields a good agreement with theory, and provides a conservative measure of system performance.

Signal-signal beat interference cancellation in spectrally-efficient WDM direct-detection Nyquist-pulse-shaped 16-QAM subcarrier modulation.

An experimental demonstration of direct-detection single-sideband Nyquist-pulse-shaped 16-QAM subcarrier modulated (Nyquist-SCM) transmission implementing a receiver-based signal-signal beat interference (SSBI) cancellation technique is described. The performance improvement with SSBI mitigation, which compensates for the nonlinear distortion caused by square-law detection, was quantified by simulations and experiments for a 7 × 25 Gb/s WDM Nyquist-SCM signal with a net optical information spectral density (ISD) of 2.0 (b/s)/Hz. A reduction of 3.6 dB in the back-to-back required OSNR at the HD-FEC threshold was achieved. The resulting reductions in BER in single channel and WDM transmission over distances of up to 800 km of uncompensated standard single-mode fiber (SSMF) achieved are presented.

Unrepeatered Nyquist PDM-16QAM transmission over 364 km using Raman amplification and multi-channel digital back-propagation.

Transmission of a net 467-Gb/s PDM-16QAM Nyquist-spaced superchannel is reported with an intra-superchannel net spectral efficiency (SE) of 6.6 (b/s)/Hz, over 364-km SMF-28 ULL ultra-low loss optical fiber, enabled by bi-directional second-order Raman amplification and digital nonlinearity compensation. Multi-channel digital back-propagation (MC-DBP) was applied to compensate for nonlinear interference; an improvement of 2 dB in Q(2) factor was achieved when 70-GHz DBP bandwidth was applied, allowing an increase in span length of 37 km.

Estimating divergently routed nonlinearly interfering channel powers using cross phase modulation.

The deployment of coherent transceivers in legacy networks requires significant investment in installation. We propose a method enabling autonomous (re-)configuration of an optical channel, which would be advantageous in legacy networks and necessary in proposed future networks utilizing a flexible frequency grid and software defined components such as reconfigurable optical add drop multiplexers (ROADM). We consider potential interfering optical channels propagating with the prospective channel along part of the fiber link which are dropped before arrival at the receiver. The method uses a commercially available line card transmitting a 40Gbit/s polarization multiplexed quadrature phase shift keying (PM-QPSK) probe channel to characterize an optical channel. The power of the nearest neighboring channels is then inferred by examining its bit error rate (BER) which is impacted by cross phase modulation (XPM) from the aggressor channels. In a 4 node network with 2 ROADMs using up to 6 aggressor OOK channels, we successfully deduce the neighboring channel power down to -2 dBm, and an extra improvement down to -3.5 dBm is gained, by measuring at an offset to the international telecommunication union (ITU) grid which also reveals inequality in neighbor channel powers.

Estimating OSNR of equalised QPSK signals.

We propose and demonstrate a technique to estimate the OSNR of an equalised QPSK signal based on the radial moments of the complex signal constellation. The technique is compared through simulation with maximum likelihood estimation and the effect of the block size used in the estimation is also assessed. The technique is verified experimentally and when combined with a single point calibration the OSNR of the input signal was estimated to within 0.5 dB.

Burst Mode Receiver for 112 Gb/s DP-QPSK with parallel DSP.

A burst mode 112 Gb/s DP-QPSK digital coherent optical receiver with parallel DSP suitable for implementation in a CMOS ASIC with a 218.75 MHz clock speed is presented. The receiver performance is validated in a five channel 50 GHz grid WDM burst switching experiment using a commercially available wavelength tunable laser as the local oscillator. A new equalizer initialization scheme that overcomes the degenerate convergence problem and ensures rapid convergence is introduced. We show that the performance of the tunable local oscillator is commensurate with burst mode coherent reception when differential decoding in employed and that required parallel DSP implementation does not seriously impair the polarization and frequency tracking performance of a digital coherent receiver under burst mode operation. We report a burst acquisition time of less than 200 ns.

Digital dual-rate burst-mode receiver for 10G and 1G coexistence in optical access networks.

A digital dual-rate burst-mode receiver, intended to support 10 and 1 Gb/s coexistence in optical access networks, is proposed and experimentally characterized. The receiver employs a standard DC-coupled photoreceiver followed by a 20 GS/s digitizer and the detection of the packet presence and line-rate is implemented in the digital domain. A polyphase, 2 samples-per-bit digital signal processing algorithm is then used for efficient clock and data recovery of the 10/1.25 Gb/s packets. The receiver performance is characterized in terms of sensitivity and dynamic range under burst-mode operation for 10/1.25 Gb/s intensity modulated data in terms of both the packet error rate (PER) and the payload bit error rate (pBER). The impact of packet preamble lengths of 16, 32, 48, and 64 bits, at 10 Gb/s, on the receiver performance is investigated. We show that there is a trade-off between pBER and PER that is limited by electrical noise and digitizer clipping at low and high received powers, respectively, and that a 16/2-bit preamble at 10/1.25 Gb/s is sufficient to reliably detect packets at both line-rates over a burst-to-burst dynamic range of 14,5 dB with a sensitivity of -18.5 dBm at 10 Gb/s.

Performance of an optical equalizer in a 10 G wavelength converting optical access network.

A centralized optical processing unit (COPU) that functions both as a wavelength converter (WC) and optical burst equaliser in a 10 Gb/s wavelength-converting optical access network is proposed and experimentally characterized. This COPU is designed to consolidate drifting wavelengths generated with an uncooled laser in the upstream direction into a stable wavelength channel for WDM backhaul transmission and to equalize the optical loud/soft burst power in order to relax the burst-mode receiver dynamic range requirement. The COPU consists of an optical power equaliser composed of two cascaded SOAs followed by a WC. Using an optical packet generator and a DC-coupled PIN-based digital burst-mode receiver, the COPU is characterized in terms of payload-BER for back-to-back and backhaul transmission distances of 22, 40, and 62 km. We show that there is a compromise between the receiver sensitivity and overload points that can be optimized tuning the WC operating point for a particular backhaul fiber transmission distance. Using the optimized settings, sensitivities of -30.94, -30.17, and -27.26 dBm with overloads of -9.3, -5, and >-5 dBm were demonstrated for backhaul transmission distances of 22, 40 and 62 km, respectively.

Generation and long-haul transmission of polarization-switched QPSK at 42.9 Gb/s.

We demonstrate, for the first time, the generation and transmission of polarization-switched QPSK (PS-QPSK) signals at 42.9 Gb/s. Long-haul transmission of PS-QPSK is experimentally investigated in a recirculating loop and compared with transmission of dual-polarization QPSK (DP-QPSK) at 42.9 Gb/s per channel. A reduction in the required OSNR of 0.7 dB was found at a BER of 3.8 x 10(-3), resulting in an increase in maximum reach of more than 30% for a WDM system operating on a 50 GHz frequency grid. The maximum reach of 13640 km for WDM PS-QPSK is, to the best of our knowledge, the longest distance reported for 40 Gb/s WDM transmission, over an uncompensated link, with standard fiber and amplification.

Ultra-long-haul transmission of 7×42.9 Gbit/s PS-QPSK and PDM-BPSK.

We investigated ultra-long-haul transmission of polarization-switched QPSK (PS-QPSK) and polarization-division-multiplexed BPSK (PDM-BPSK) at 42.9 Gbit/s experimentally as well as by means of computer simulations. PDM-BPSK allowed transmission distances in excess of 14,040 km to be achieved, compared to 13,640 km for PS-QPSK. However, PS-QPSK offers a significant reduction in receiver complexity due to the lower symbol-rate.

Optically equalized 10 Gb/s NRZ digital burstmode receiver for dynamic optical networks.

A 10Gb/s NRZ burst-mode optical receiver suitable for receiving asynchronous bursts with power variations of up to 7 dB is presented. The digital burst mode receiver is based on a standard AC-coupled photodiode followed by asynchronous analogue to digital conversion at 20 GS/s. Symbol timing, amplitude and baseline wander corrections are implemented in digital signal processing without the need for additional linecoding, such as 8B10B, and special AC-coupling schemes. It is assumed that G.709 framing together with enhanced FEC is used therefore the receiver is characterized using a pre eFEC BER of 10(-3) at an input OSNR of 10 dB. We show that the addition of an electronically controlled SOA for optical power equalization before the receiver extends the burst-to-burst dynamic range from the 7 dB provided by the digital receiver alone to 16.5 dB. The large dynamic range, low overhead, and burst length versatility make this type of receiver ideal for applications in both synchronous and asynchronous dynamic network architectures with burst timescales ranging from nanoseconds through to continuous data.

Equalization enhanced phase noise in Nyquist-spaced superchannel transmission systems using multi-channel digital back-propagation.

Superchannel transmission spaced at the symbol rate, known as Nyquist spacing, has been demonstrated for effectively maximizing the optical communication channel capacity and spectral efficiency. However, the achievable capacity and reach of transmission systems using advanced modulation formats are affected by fibre nonlinearities and equalization enhanced phase noise (EEPN). Fibre nonlinearities can be effectively compensated using digital back-propagation (DBP). However EEPN which arises from the interaction between laser phase noise and dispersion cannot be efficiently mitigated, and can significantly degrade the performance of transmission systems. Here we report the first investigation of the origin and the impact of EEPN in Nyquist-spaced superchannel system, employing electronic dispersion compensation (EDC) and multi-channel DBP (MC-DBP). Analysis was carried out in a Nyquist-spaced 9-channel 32-Gbaud DP-64QAM transmission system. Results confirm that EEPN significantly degrades the performance of all sub-channels of the superchannel system and that the distortions are more severe for the outer sub-channels, both using EDC and MC-DBP. It is also found that the origin of EEPN depends on the relative position between the carrier phase recovery module and the EDC (or MC-DBP) module. Considering EEPN, diverse coding techniques and modulation formats have to be applied for optimizing different sub-channels in superchannel systems.

Spectrally shaped DP-16QAM super-channel transmission with multi-channel digital back-propagation.

The achievable transmission capacity of conventional optical fibre communication systems is limited by nonlinear distortions due to the Kerr effect and the difficulty in modulating the optical field to effectively use the available fibre bandwidth. In order to achieve a high information spectral density (ISD), while simultaneously maintaining transmission reach, multi-channel fibre nonlinearity compensation and spectrally efficient data encoding must be utilised. In this work, we use a single coherent super-receiver to simultaneously receive a DP-16QAM super-channel, consisting of seven spectrally shaped 10GBd sub-carriers spaced at the Nyquist frequency. Effective nonlinearity mitigation is achieved using multi-channel digital back-propagation (MC-DBP) and this technique is combined with an optimised forward error correction implementation to demonstrate a record gain in transmission reach of 85%; increasing the maximum transmission distance from 3190 km to 5890 km, with an ISD of 6.60 b/s/Hz. In addition, this report outlines for the first time, the sensitivity of MC-DBP gain to linear transmission line impairments and defines a trade-off between performance and complexity.