Analysis on Isotropic and Anisotropic Samples of Polypropylene/Polyethyleneterephthalate Blend/Graphene Nanoplatelets Nanocomposites: Effects of a Rubbery Compatibilizer.

Over the past few years, polymer nanocomposites have garnered a significant amount of interest from both the scientific community and industry due to their remarkable versatility and wide range of potential uses in various fields, including automotive, electronics, medicine, textiles and environmental applications. In this regard, this study focuses on the influence of a compatibilizer rubber on a nanocomposite incorporating graphene nanoparticles (GNPs), with a polymer matrix based on a blend of polypropylene (PP) and polyethylene terephthalate (PET). This effect has been investigated on both isotropic samples and on anisotropic/spun fiber samples. The influence of the compatibilizer rubber on morphological, rheological and mechanical properties was analysed and discussed. Mechanical and morphological properties were evaluated on both isotropic samples obtained by compression moulding and melt-spun fibers. The addition of the rubbery compatibilizer increased the viscosity, improving interfacial adhesion, and the same effect was observed for the melt strength and breaking stretching ratios. Mechanical properties, including the elastic modulus, tensile strength and elongation at break, improved in both types of samples but more significantly in the fibers. These improvements were attributed to the orientation of the matrix, the formation of PET microfibrils, and the reduction in the size of graphene nanoparticles due to the action of the elongational flow. This reduction, facilitated by the elongation flow and the action of the compatibilizer, improved matrix-nanofiller adhesion due to the increased contact area between the two polymeric phases and between the filler and matrix. Finally, a transition from brittle to ductile behaviour was observed, particularly in the system with the compatibilizer, attributed to defect reduction and improved stress transmission.

Recycling of Heterogeneous Mixed Waste Polymers through Reactive Mixing.

Anything that is not recycled and/or recovered from waste represents a loss of raw materials. Recycling plastics can help to reduce this loss and to reduce greenhouse gases, improving the goal of the decarbonization of plastic. While the recycling of single polymers is well assessed, the recycling of mixed plastics is very difficult because of the strong incompatibility among the different polymers usually present in urban waste. In this work, heterogeneous mixed polymers, i.e., polyethylene (PE), polypropylene (PP), polystyrene (PS) and polyethylenetherephthalate (PET) were processed using a laboratory mixer under different conditions of temperature, rotational speed and time to evaluate the effect of the above parameters on morphology, viscosity and mechanical properties of the final blends. Morphological analysis shows a strong incompatibility between the polyethylene matrix and the other dispersed polymers. The blends show, of course, a brittle behavior, but this behavior slightly improves with decreasing temperature and increasing rotational speed. A brittle-ductile transition was observed only at a high level of mechanical stress obtained by increasing rotational speed and decreasing temperature and processing time. This behavior has been attributed to both a decrease in the dimensions of the particles of the dispersed phase and to the formation of a small amount of copolymers that act as adhesion promoters between matrix and dispersed phases.

The Use of Waste Hazelnut Shells as a Reinforcement in the Development of Green Biocomposites.

Biodegradable Mater-Bi (MB) composites reinforced with hazelnut shell (HS) powder were prepared in a co-rotating twin-screw extruder followed by compression molding and injection molding. The effects of reinforcement on the morphology, static and dynamic mechanical properties, and thermal and rheological properties of MB/HS biocomposites were studied. Rheological tests showed that the incorporation of HS significantly increased the viscosity of composites with non-Newtonian behavior at low frequencies. On the other hand, a scanning electron microscope (SEM) examination revealed poor interfacial adhesion between the matrix and the filler. The thermal property results indicated that HS could act as a nucleating agent to promote the crystallization properties of biocomposites. Furthermore, the experimental results indicated that the addition of HS led to a significant improvement in the thermomechanical stability of the composites. This paper demonstrates that the incorporation of a low-cost waste product, such as hazelnut shells, is a practical way to produce low-cost biocomposites with good properties. With a content of HS of 10%, a remarkable improvement in the elastic modulus and impact strength was observed in both compression and injection-molded samples. With a higher content of HS, however, the processability in injection molding was strongly worsened.

Toward the Decarbonization of Plastic: Monopolymer Blend of Virgin and Recycled Bio-Based, Biodegradable Polymer.

Decarbonization of plastics is based on two main pillars: bio-based polymers and recycling. Mechanical recycling of biodegradable polymers could improve the social, economic and environmental impact of the use of these materials. In this regard, the aim of this study was to investigate whether concentrations of the same recycled biopolymer could significantly affect the rheological and mechanical properties of biodegradable monopolymer blends. Monopolymer blends are blends made of the same polymers, virgin and recycled. A sample of commercially available biodegradable blend was reprocessed in a single-screw extruder until two extrusion cycles were completed. These samples were exposed to grinding and melt reprocessed with 75% and 90% of the same virgin polymer. The blends were characterized by tensile tests and rheological tests. The results obtained showed that while multiple extrusions affected the mechanical and rheological properties of the polymer, the concentration of the reprocessed material present in the blends only very slightly affected the properties of the virgin material. In addition, the experimentally observed trends were accurately predicted by the additive model adopted.

Biocomposite PBAT/lignin blown films with enhanced photo-stability.

Lignin can be obtained as a byproduct during cellulose-rich pulp fibers production and it is habitually treated as waste or intended for low-value destinations. However, due to UV absorption and mechanical properties, lignin can contribute to the fabrication of biodegradable blown films with superior performances. In this study, it was established the suitability of lignin for manufacturing biocomposite PBAT blown films with higher stiffness and photo-oxidation resistance. The effect of the filler concentration on the melt rheological behavior in non-isothermal elongational flow was investigated. The results allowed us to choose the correct filler concentration for producing films through a film blowing operation. The PBAT/lignin blown film composites displayed an increase of the elastic modulus if compared to neat PBAT films without affecting their elongation at break. Furthermore, the filler delayed the photo-oxidative degradation of PBAT hence potentially allowing open-air applications.

Effect of Moisture Content on the Processing and Mechanical Properties of a Biodegradable Polyester.

This work is focused on the influence of moisture content on the processing and mechanical properties of a biodegradable polyester used for applications in injection molding. The pellets of the biodegradable polyester were exposed under different relative humidity conditions at a constant temperature before being compression molded. The compression-molded specimens were again placed under the above conditions before the mechanical testing. With all these samples, it is possible to determine the effect of moisture content on the processing and mechanical properties separately, as well as the combined effect of moisture content on the mechanical properties. The results obtained showed that the amount of absorbed water-both before processing and before mechanical testing-causes an increase in elongation at break and a slight reduction of the elastic modulus and tensile strength. These changes have been associated with possible hydrolytic degradation during the compression molding process and, in particular, with the plasticizing action of the moisture absorbed by the specimens.

Investigation on the Properties and on the Photo-Oxidation Behaviour of Polypropylene/Fumed Silica Nanocomposites.

This work investigates the effects of very small amounts of fumed silica on the morphology and on the rheological and mechanical behaviour of polypropylene nanocomposites and on their photo-oxidation behaviour. Polypropylene nanocomposites were prepared using a twin-screw corotating extruder with 0, 1 and 2 wt/wt% of SiO2. Morphological, mechanical, thermomechanical and rheological properties were examined. It was found that the viscosity of the matrix is reduced by the presence of the silica nanoparticles, suggesting a poor adhesion between the two phases and probably some lubricating effect. On the contrary, the mechanical and, in particular, the thermomechanical properties of the matrix are considerably improved by the presence of the silica. In particular, elastic modulus and tensile strength increases remarkably, and this effect becomes more and more remarkable with an increasing temperature. As for the photo-oxidation behaviour, the presence of silica improves the photostability of the polypropylene matrix. This effect has been attributed to both the barrier to the oxygen and to the absorbance of the UV radiation from the silica nanoparticles. Finally, no significant effect of the silica nanoparticles has been put in evidence on the crystallisation behaviour of the polypropylene. As for the effect of the silica content, the difference in the properties of the two nanocomposites is relatively small and all the measured properties depend much less than linearly with its amount. This has been correlated with the reaggregation of the nanoparticles that, having a larger size, decrease the contact area between the matrix and the filler.

Use of Biochar as Filler for Biocomposite Blown Films: Structure-Processing-Properties Relationships.

In this work, biocomposite blown films based on poly(butylene adipate-co-terephthalate) (PBAT) as biopolymeric matrix and biochar (BC) as filler were successfully fabricated. The materials were subjected to a film-blowing process after being compounded in a twin-screw extruder. The preliminary investigations conducted on melt-mixed PBAT/BC composites allowed PBAT/BC 5% and PBAT/BC 10% to be identified as the most appropriate formulations to be processed via film blowing. The blown films exhibited mechanical performances adequate for possible application as film for packaging, agricultural, and compost bags. The addition of BC led to an improvement of the elastic modulus, still maintaining high values of deformation. Water contact angle measurements revealed an increase in the hydrophobic behavior of the biocomposite films compared to PBAT. Additionally, accelerated degradative tests monitored by tensile tests and spectroscopic analysis revealed that the filler induced a photo-oxidative resistance on PBAT by delaying the degradation phenomena.

Morphology, Rheological and Mechanical Properties of Isotropic and Anisotropic PP/rPET/GnP Nanocomposite Samples.

The effect of graphene nanoplatelets (GnPs) on the morphology, rheological, and mechanical properties of isotropic and anisotropic polypropylene (PP)/recycled polyethylene terephthalate (rPET)-based nanocomposite are reported. All the samples were prepared by melt mixing. PP/rPET and PP/rPET/GnP isotropic sheets were prepared by compression molding, whereas the anisotropic fibers were spun using a drawing module of a capillary viscometer. The results obtained showed that the viscosity of the blend is reduced by the presence of GnP due to the lubricating effect of the graphene platelets. However, the Cox-Merz rule is not respected. Compared to the PP/rPET blend, the GnP led to a slight increase in the elastic modulus. However, it causes a slight decrease in elongation at break. Morphological analysis revealed a poor adhesion between the PP and PET phases. Moreover, GnPs distribute around the droplets of the PET phase with a honey-like appearance. Finally, the effect of the orientation on both systems gives rise not only to fibers with higher modulus values, but also with high deformability and a fibrillar morphology of the dispersed PET phase. A fragile-ductile transition driven by the orientation was observed in both systems.

PBAT Based Composites Reinforced with Microcrystalline Cellulose Obtained from Softwood Almond Shells.

This study explores the processability, mechanical, and thermal properties of biocompostable composites based on poly (butylene adipate-co-terephthalate) (PBAT) as polymer matrix and microcrystalline cellulose (MCC) derived from softwood almond (Prunus dulcis) shells (as-MCC) as filler at two different weight concentration, i.e., 10 wt% and 20 wt%. The materials were processed by melt mixing and a commercial MCC (c-MCC) was used as filler comparison. The fibrillar shape of as-MCC particles was found to change the rheological behavior of PBAT, particularly at the highest concentration. The melt mixing processing allowed obtaining a uniform dispersion of both kinds of fillers, slightly reducing the L/D ratio of as-MCC fibers. The as-MCC particles led to a higher increase of the elastic modulus of PBAT if compared to the c-MCC counterparts. Both the MCC fillers caused a drastic reduction of the elongation at break, although it was higher than 120% also at the highest filler concentrations. DSC analysis revealed that both MCC fillers poorly affected the matrix crystallinity, although as-MCC induced a slight PBAT crystallinity increase from 8.8% up to 10.9% for PBAT/as-MCC 20%. Therefore, this work demonstrates the great potential of MCC particles derived from almond shells as filler for biocompostable composites fabrication.

Recycling of a Biodegradable Polymer Blend.

Mechanical recycling is one of the possible ways to enhance the value of postconsumer plastic materials. However, the final performance of the recycled material will strongly depend on the quality of the selection made on the recycled product and on the degradation of the properties. In this context, the present study examines the effect of reprocessing for five successive extrusion cycles on the rheological, mechanical and thermal properties of a poly(butylene adipate-co-terephthalate) (PBAT)-based blend on samples reprocessed in both dry and wet conditions. The results showed that when the sample was processed after drying, degradation of the material was less than when it was processed in wet conditions. However, the experimental results showed that the decrease of rheological and mechanical properties was not so dramatic, and therefore the material could be reused in both cases.