Effects of staining and artificial aging on optical properties of gingiva-colored resin-based restorative materials.

OBJECTIVES: To evaluate CIEDE2000/CIELAB differences in color (ΔE00/ΔEab), and translucency parameter (ΔTP00/ΔTPab), and gloss of gingiva-colored resin-based restorative materials upon staining/aging. MATERIALS AND METHODS: Disc-shaped, 10 mm in diameter, and 2-mm-thick samples (n = 5/group) were made from giomer (Beautifil II gingiva), oligomer-based (crea.lign GUM gel), CAD/CAM polymethyl-methacrylate-based (IvoBase CAD), PMMA-based (ProBase Hot), and dimethacrylate-based (SR Nexco Paste Gingiva). Color and gloss were recording using a benchtop spectrophotometer and gloss meter, respectively, at baseline (T0), and upon staining in coffee or red wine for 60 (T1) and 120 h (T2), or artificial aging of 150 kJ/m2 (T1) and 300 kJ/m2 (T2). Three-way analysis of variance (materials x staining conditions x time intervals), Tukey's test (α = 0.05), and Pearson's correlation test were used in analytical statistics. RESULTS: CIEDE2000 color differences ranged from 1.0 to 4.4 (coffee), 1.5 to 5.3 (wine), and 0.9 to 2.0 after artificial aging, with ΔE00 values being significantly higher for Beautifil than other materials (p < 0.05). ΔTP00 values ranged from 0.2 to 0.7 and were statistically higher upon staining in wine compared to artificial aging (p < 0.05). Gloss values at T0 were 76.7-87.0. Beautifil exhibited the lowest gloss retention (50.8-60.2%) after staining, compared to > 90% of other materials (p < 0.05). ΔE00/ΔEab and ΔTP00/ΔTPab were positively correlated (p < 0.0001). CONCLUSIONS: Color, translucency, and gloss changes of gingiva-colored restorative materials were material- and staining/aging-dependent. Generally, wine caused greatest changes in color (with IvoBase CAD being the most color stable) and translucency parameter. All materials except Beautifil gingiva II exhibited staining- and aging-dependent gloss retention greater than 90% for all compared time intervals. CLINICAL RELEVANCE: Optical properties of resin-based gingiva-colored restorative materials depend on material, staining/aging conditions, and exposure time. Certain materials should be avoided in individuals with high consumption of red wine and coffee.

Immediate Vs Early Loading of Bone Level Tapered Dental Implants With Hydrophilic Surface in Rehabilitation of Fully Edentulous Maxilla: Clinical and Patient Centered Outcomes.

The aim was to: (1) compare changes among primary and secondary implant stability between immediate and early loaded implants in edentulous maxilla, (2) evaluate oral health-related quality of life (OHRQoL), and (3) determine patient satisfaction with 6 implant supported fixed full-arch dentures. A prospective, randomized controlled clinical trial was conducted on 24 edentulous maxilla patients. The BLT SLActive implants in 12 patients were immediately loaded with temporary restorations while 12 patients did not receive temporary restorations. Definitive (final) dentures were delivered to all patients after 6 weeks. Stability of the implants were assessed by insertion torque (IT) and resonance frequency analysis (RFA). Oral Health Impact Profile-19 (OHIP-19) questionnaire was used to evaluate OHRQoL and a visual analogue scale (VAS) was used for patient satisfaction. The IT value of implants assigned for immediate and early loading group was 27.17 ± 9.55 Ncm and 25.01 ± 11.06 Ncm, respectively. Changes in implant stability from baseline to week 6 were similar in both groups when measured by Penguin (P = .881) and Ostell (P = .828). Patients in the immediate loading group reported significantly lower OHIP physical pain scores (P = .016) and OHIP psychological disability score (P = .046), and the patients reported significantly higher VAS function score (P = .009) and VAS esthetics score (P = .009). Implant loading protocols do not have a significant effect on the change in implant stability 6 weeks after implantation; however, immediate loading significantly improves OHRQoL as well as satisfaction of patients with maxillary edentulism treated by fixed full-arch dentures. Future trials will determine the role of immediate loading protocol in clinical scenarios with various amounts of available jaw bone using different numbers of implants to retain a fixed prosthetic restoration in the edentulous maxilla.

Color adjustment potential of resin composites.

OBJECTIVES: The purpose of this study was to evaluate color adjustment potential (CAP) of resin composites. MATERIALS AND METHODS: Two shades of each of eight commercial resin composites and one control shade were evaluated. Visual (color competent observers, controlled conditions) and instrumental color evaluations (spectroradiometer, spectrophotometer) were performed. The data were analyzed by analysis of variance, Fisher's PLSD intervals for comparison of means, and Spearman's rank order correlation. RESULTS: Instrumental color adjustment potential (CAP-I) ranged from - 0.51 to 0.74, and corresponding Fisher's PLSD intervals were 0.1 and 0.05, respectively (p < 0.0001, power 1.0). Visual color adjustment potential (CAP-V) ranged from 0.10 to 0.78, and corresponding Fisher's PLSD intervals were 0.2 and 0.1, respectively (p < 0.0001, power 1.0). The greatest overall color shifting between test shades in isolation and the same shades surrounded by control shade were recorded for HRi ENA enamel, followed by Clearfil Majesty ES2. The highest visual CAP (blending) was recorded for Herculite Ultra, HRi ENA enamel, and Clearfil Majesty ES2. CONCLUSION: Within the limitation of the study, it was found that color adjustment potential (CAP) was composite and shade-dependent. Positive CAP was recorded both instrumentally and visually for majority of composites and shades. Overall, the measured color difference reduction associated with positive CAP was 31%, while the average visual CAP was 43%. CLINICAL RELEVANCE: Resin composites with pronounced color adjustment potential interact with surrounding dental restorations. Introduced CAP-V and CAP-I were indirect measurements of blending (optical illusion).

Immediate versus early loading of immediately placed bone-level tapered dental implants with hydrophilic surface in full arch maxillary rehabilitation: A pilot randomized clinical trial with 2-year follow-up.

This study aimed to compare implant stabilities between the immediate and early loaded, immediately placed bone-level tapered dental implants in the maxilla and to evaluate marginal bone loss (MBL), oral health-related quality of life (OHRQoL), and patient satisfaction at a 2-year follow-up. A pilot, prospective, randomized, controlled clinical trial was conducted on 24 maxillary failing dentition patients. The bone-level tapered implants of 12 patients were immediately loaded with temporary restorations, while the other 12 patients did not receive any kind of temporization. Implant-supported screw-retained complete porcelain-fused-to-metal prostheses were delivered to all patients in the seventh postoperative week. The insertion torque values of implants assigned to the immediate and early loading groups were 33.0 ± 4.87 and 29.26 ± 8.31 Ncm, respectively. The dynamics of implant stability changes from implant placement up to a 2-year follow-up were similar for both groups (Penguin®, p = 0.268; Ostell®, p = 0.552), while the MBL was at submillimeter level. The cumulative implant survival rate was 91.80% for immediately loaded implants and 97.22% for early loaded implants, without significant difference (p = 0.162). The total score on the Oral Health Impact Profile questionnaire significantly decreased over time in both groups, indicating improvement in OHRQoL (p < 0.001), and the high level of patient satisfaction remained after 2 years of function regardless of a loading protocol. Both loading protocols, immediate and early, of six immediately placed bone-level tapered dental implants are an adequate treatment choice for fixed rehabilitation of the maxillary failing dentition.

Apolipoprotein ɛ4 Allele and Dental Occlusion Deficiency as Risk Factors for Alzheimer's Disease.

Compromised dentition has been suggested to pose a significant risk factor for dementia. It was mainly investigated through insufficient tooth number, disregarding contact between opposing teeth (dental occlusion). The ɛ4 allele of apolipoprotein (APOE4) is the primary genetic marker for the late onset of Alzheimer's disease (AD). However, APOE4 and dental occlusion have not yet been investigated as possible associated risk factors for AD. The study was aimed to examine the impact of dental status and different APOE gene variants on AD occurrence. Secondly, sociodemographic variables were investigated as factors potentially associated with AD. The case-control study included two groups: 116 patients with AD (according to the NINDS-ADRDA criteria) and 63 controls (Mini-Mental State Examination scores ≥24). The analysis of APOE gene polymorphism was conducted through PCR reaction. Dental examination included recording of number of teeth, presence of fixed or removable dentures, and number of functional tooth units (FTU). Regression analysis was used to investigate the joint effect of the clinical and genetic variables on AD. Results showed that patients with AD were more often carriers of ɛ3/ɛ4 genotype and ɛ4 allele, had lower number of teeth and FTU, and were less likely to be married, live in home, and had less chronic diseases, compared to the controls. Regression analysis showed that presence of APOE4 allele and the number of total FTU remained associated with AD, even when adjusted for age, sex, and level of education. In conclusion, deficient dental occlusion and presence of APOE4 may independently increase risk for AD.

Optical properties of composite restorations influenced by dissimilar dentin restoratives.

OBJECTIVES: To evaluate optical properties (color and translucency) of 'sandwich' restorations of resin-based composites and esthetically unfavorable dentin restoratives. METHODS: Cylindrical 'dentin' specimens (8mm in diameter and 2mm thick, N=5/group) were prepared using EverX Posterior (GC), Biodentine (Septodont), experimental hydroxyapatite (HAP) or conventional composites (Gradia Direct Posterior, GC; Filtek Z250 and Filtek Z500, 3M ESPE). Capping 'enamel' layers were prepared using composites (Gradia Direct Posterior, Filtek Z250 or Z550) of A1 or A3 shade and the following thickness: 0.6, 1 or 2mm. Color (ΔE) and translucency parameter (TP) were determined using a spectrophotometer (VITA Easyshade Advance 4.0, VITA Zahnfabrik). Data were statistically analyzed using analysis of variance with Tukey's post-hoc tests (α=0.05). RESULTS: TP was greatly affected by layer thickness, whilst ΔE depended on shade and layer thickness of the capping composite. HAP and Biodentine showed significantly lower TP and higher ΔE (deviation from 'ideal white') than composites (p<0.05). Greater TP was seen in EverX_composite groups than in corresponding control groups of the same shade and thickness. TP of composites combined with Biodentine or HAP was below 2, lower than the corresponding control groups (p<0.05). Within-group differences of ΔE were greatest in HAP_composite groups. EverX_Gradia and EverX_FiltekZ250 combinations showed the most comparable ΔE with the control groups. SIGNIFICANCE: A 2mm thick layer of composite covering dentin restoratives with unfavorable esthetics is recommended for a final 'sandwich' restoration that is esthetically comparable to a conventional, mono-composite control restoration.

Measurement of the accuracy of dental working casts using a coordinate measuring machine.

Background/Aim: Dental impressions present a negative imprint of intraoral tissues of a patient which is, by pouring in gypsum, transferred extraorally on the working cast. Casting an accurate and precise working cast presents the first and very important step, since each of the following stages contributes to the overall error of the production process, which can lead to inadequately fitting dental restorations. The aim of this study was to promote and test a new model and technique for in vitro evaluation of the dental impression accuracy, as well as to asses the dimensional stability of impression material depending on the material bulk, and its effect on the accuracy of working casts. Methods: Impressions were made by the monophasic technique using the experimental master model. Custom trays with spacing of 1, 2 and 3 mm were constructed by rapid prototyping. The overall of 10 impressions were made with each custom tray. Working casts were made with gypsum type IV. Measurement of working casts was done 24 h later using a co-ordinate measuring machine. Results: The obtained results show that the working casts of all the three custom trays were in most cases significantly different in the transversal and sagittal planes in relation to the master model. The height of abutments was mainly unaffected. The degree of convergence showed certain significance in all the three custom trays, most pronounced in the tray with 3 mm spacing. Conclusion: The impression material bulk of 1­3 mm could provide accurate working casts when using the monophasic impression technique. The increase of the distance between abutment teeth influences the accuracy of working casts depending on the material bulk. [Projekat Ministarstva nauke Republike Srbije, br. TR 35020: Research and development of modelling methods and approaches in manufacturing of dental recoveries with the application of modern technologies and computer aided systems]

Analysis of load distribution in tooth-implant supported fixed partial dentures by the use of resilient abutment.

INTRODUCTION: Differences between the tooth and implant response to load can lead to many biological and technical implications in the conditions of occlusal forces. OBJECTIVE: The objective of this study was to analyze load distribution in tooth/implant-supported fixed partial dentures with the use of resilient TSA (Titan Shock Absorber, BoneCare GmbH, Augsburg, Germany) abutment and conventional non-resilient abutment using finite element method. METHODS: This study presents two basic 3D models. For one model a standard non-resilient abutment is used, and on the implant of the second model a resilient TSA abutment is applied. The virtual model contains drawn contours of tooth, mucous membranes, implant, cortical bones and spongiosa, abutment and suprastructure. The experiment used 500 N of vertical force, applied in three different cases of axial load. Calculations of von Mises equivalent stresses of the tooth root and periodontium, implants and peri-implant tissue were made. RESULTS: For the model to which a non-resilient abutment is applied, maximum stress values in all three cases are observed in the cortical part of the bone (maximum stress value of 49.7 MPa). Measurements of stress and deformation in the bone tissue in the model with application of the resilientTSA abutment demonstrated similar distribution; however, these values are many times lower than in the model with non-resilient TSA abutment (maximum stress value of 28.9 MPa). CONCLUSION: Application of the resilient TSA abutment results in more equal distribution of stress and deformations in the bone tissue under vertical forces. These values are many times lower than in the model with the non-resilient abutment.

Finite element analysis in defining the optimal shape and safety factor of retentive clasp arms of a removable partial denture.

BACKGROUND/AIM: Retentive force of removable partial denture (RPD) directly depends on elastic force of stretched retentive clasp arms (RCAs). During deflection RCA must have even stress distribution. Safety factor is the concept which can be applied in estimating durability and functionality of RCAs. This study was based on analyzing properties of clasps designed by conventional clasp wax profiles and defining the optimal shapes of RCAs for stress distribution and safety factor aspects. METHODS: Computer-aided-design (CAD) models of RCAs with simulated properties of materials used for fabrication of RPD cobalt-chromium-molybdenum (CoCrMo) alloy, commercially pure titanium (CPTi) and polyacetale were analzed. RESULTS: The research showed that geometrics of Rapidflex profiles from the BIOS concept are defined for designing and modeling RCAs from CoCrMo alloys. I-Bar and Bonihard clasps made from CPTi might have the same design as Co-CoCrMo clasp only by safety factor aspect, but it is obvious that CPTi are much more flexible, so their shape must be more massive. Polyacetale clasps should not be fabricated by BIOS concept for CoCrMo alloy. A proof for that is the low value of safety factor. CONCLUSION: The BIOS concept should be used only for RCAs made of CoCrMo alloy and different wax profiles should be used for fabricating clasps of other investigated materials. The contribution of this study may be the improve ment of present systems for defining the clasps shapes made from (CoCrMo alloys. The more significant application is the possibility of creating new concepts in defining shapes of RCA made from CPTi and polyacetale.

[Fracture toughness of zirconia ceramic crowns made by feather-edge tooth preparation design].

BACKGROUND/AIM: Fracture toughness determines functional crown strenght and prevents damages on ceramics during mastication. There is a lack of relevant literature data about fracture toughness of crowns made by feather-edge preparation. Mechanical testing of ceramic samples is supposed to show if feather-edge tooth preparation is a successful method for making ceramic crowns without any risk of reduction of their mechanical properties. This research was done to establish effects of feather-edge tooth preparation on fracture toughness of single zirconia ceramic crowns. METHODS: The research was performed as an experimental study. Sixty (60) ceramic crowns were made on non-carious extracted human premolars. Thirty (30) crowns were made on the basis of feather-edge preparation (experimental group I). The group II included 30 crowns made on 1 mm rounded shoulder. Crowns fabrication was executed on a copy mill production system "Zirkonzahn" (Zirkonzahn GMBH, Gais, Germany). The spherical compression test was used to determine fracture toughness, using 6 mmn diameter ceramic ball. Fracture load for damaging ceramic crown was recorded on a universal testing machine--Zwick, type 1464, with the speed of 0.05 mm/min. RESULTS: The results of this research introduced significant differences between fracture toughness of ceramic samples in every examined group. However, fracture toughness of crowns from both group was above 2000 N, what was double beyond a recommended value. The mean value of fracture toughness in the feather-edge group was 2090 N, and in shoulder group it was 2214 N. CONCLUSION: This research showed a high fracture toughness of zirconia crowns made on feather-edge preparation. The examined crowns showed a fracture resistance at a sufficient distance in relation to the minimum values of functional loads. Further research of functional loads of these crown is necessary, as well as research of marginal adaptation of cemented crowns and gingival inflammatory response.

[Accuracy of optical scanning methods of the Cerec 3D system in the process of making ceramic inlays].

BACKGROUND/AIM: One of the results of many years of Cerec 3D CAD/CAM system technological development is implementation of one intraoral and two extraoral optical scanning methods which, depending on the current indications, are applied in making fixed restorations. The aim of this study was to determine the degree of precision of optical scanning methods by the use of the Cerec 3D CAD/CAM system in the process of making ceramic inlays. METHODS: The study was conducted in three experimental groups of inlays prepared using the procedure of three methods of scanning Cerec 3D system. Ceramic inlays made by conventional methodology were the control group. The accuracy of optical scanning methods of the Cerec 3D system computer aided design-computer aided manufacturing (CAD/CAM) was indirectly examined by measuring a marginal gap size between inlays and demarcation preparation by scanning electron microscope (SEM). RESULTS: The results of the study showed a difference in the accuracy of the existing methods of scanning dental CAD/CAM systems. The highest level of accuracy was achieved by the extraoral optical superficial scanning technique. The value of marginal gap size inlays made with the technique of extraoral optical superficial scanning was 32.97 +/- 13.17 mus. Techniques of intraoral optical superficial and extraoral point laser scanning showed a lower level of accuracy (40.29 +/- 21.46 mus for inlays of intraoral optical superficial scanning and 99.67 +/- 37.25 mus for inlays of extraoral point laser scanning). CONCLUSION: Optical scanning methods in dental CAM/CAM technologies are precise methods of digitizing the spatial models; application of extraoral optical scanning methods provides the highest precision.