Advances in Dynamization of Plate Fixation to Promote Natural Bone Healing.

The controlled dynamization of fractures can promote natural fracture healing by callus formation, while overly rigid fixation can suppress healing. The advent of locked plating technology enabled new strategies for the controlled dynamization of fractures, such as far cortical locking (FCL) screws or active plates with elastically suspended screw holes. However, these strategies did not allow for the use of non-locking screws, which are typically used to reduce bone fragments to the plate. This study documents the first in vivo study on the healing of ovine tibia osteotomies stabilized with an advanced active plate (AAP). This AAP allowed plate application using any combination of locking and non-locking screws to support a wide range of plate application techniques. At week 9 post-surgery, tibiae were harvested and tested in torsion to failure to assess the healing strength. The five tibiae stabilized with an AAP regained 54% of their native strength and failed by spiral fracture through a screw hole, which did not involve the healed osteotomy. In comparison, tibiae stabilized with a standard locking plate recovered 17% of their strength and sustained failure through the osteotomy. These results further support the stimulatory effect of controlled motion on fracture healing. As such, the controlled dynamization of locked plating constructs may hold the potential to reduce healing complications and may shorten the time to return to function. Integrating controlled dynamization into fracture plates that support a standard fixation technique may facilitate the clinical adoption of dynamic plating.

Effect of helmet design on impact performance of industrial safety helmets.

Background: Comparative studies of different helmet designs are essential to determine differences in helmet performance. The present study comparatively evaluated the impact performance of hardhat helmets, climbing-style safety helmets, and helmets with novel rotation-damping technologies to determine if advanced designs deliver improved protection. Methods: Six helmet designs from three categories of safety helmets were tested: two traditional hardhat helmets (HH Type I, HH Type II), two climbing-style helmets (CS Web, CS Foam), and two helmets with dedicated rotation-damping technologies (MIPS, CEL). Helmets were first evaluated in impacts of 31 J energy representing a falling object according to standard Z89.1-2014. Subsequently, helmets were evaluated in impacts representing a fall by dropping a helmeted head-neck surrogate at 275 J impact energy. The resulting head kinematics were used to calculate the probability of sustaining a head or brain injury. Results: Crown impacts representative of a falling object resulted in linear acceleration of less than 50 g in all six helmet models. Compared to crown impacts, front, side and rear impacts caused a several-fold increase in head acceleration in all helmets except HH Type II and CEL helmets. For impacts representative of falls, all helmets except the CEL helmet exhibited significantly increased head accelerations and an increased brain injury probability compared to the traditional HH Type I hardhat. Neck compression was 35%-90% higher in the two climbing-style helmets and 80% higher in MIPS helmets compared to the traditional HH type I hardhat. Discussion: Contemporary helmets do not necessarily deliver improved protection from impacts and falls compared to traditional hardhat helmets.

Impact Performance Comparison of Advanced Snow Sport Helmets with Dedicated Rotation-Damping Systems.

Rotational acceleration of the head is a principal cause of concussion and traumatic brain injury. Several rotation-damping systems for helmets have been introduced to better protect the brain from rotational forces. But these systems have not been evaluated in snow sport helmets. This study investigated two snow sport helmets with different rotation-damping systems, termed MIPS and WaveCel, in comparison to a standard snow sport helmet without a rotation-damping system. Impact performance was evaluated by vertical drops of a helmeted Hybrid III head and neck onto an oblique anvil. Six impact conditions were tested, comprising two impact speeds of 4.8 and 6.2 m/s, and three impact locations. Helmet performance was quantified in terms of the linear and rotational kinematics, and the predicted probability of concussion. Both rotation-damping systems significantly reduced rotational acceleration under all six impact conditions compared to the standard helmet, but their effect on linear acceleration was less consistent. The highest probability of concussion for the standard helmet was 89%, while helmets with MIPS and WaveCel systems exhibited a maximal probability of concussion of 67 and 7%, respectively. In conclusion, rotation-damping systems of advanced snow sport helmets can significantly reduce rotational head acceleration and the associated concussion risk.

Impact Performance Comparison of Advanced Bicycle Helmets with Dedicated Rotation-Damping Systems.

Bicycle helmets effectively mitigate skull fractures, but there is increasing concern on their effectiveness in mitigating traumatic brain injury (TBI) caused by rotational head acceleration. Bicycle falls typically involve oblique impacts that induce rotational head acceleration. Recently, bicycle helmet with dedicated rotation-damping systems have been introduced to mitigate rotational head acceleration. This study investigated the impact performance of four helmets with different rotation-damping systems in comparison to a standard bicycle helmet without a rotation-damping system. Impact performance was tested under oblique impact conditions by vertical drops of a helmeted headform onto an oblique anvil at 6.2 m/s impact speed. Helmet performance was quantified in terms of headform kinematics, corresponding TBI risk, and resulting brain strain. Of the four rotation-damping systems, two systems significantly reduced rotational head acceleration, TBI risk, and brain strain compared to the standard bicycle helmet. One system had no significant effect on impact performance compared to control helmets, and one system significantly increase linear and rotational head acceleration by 62 and 61%, respectively. In conclusion, results revealed significant differences in the effectiveness between rotation-damping systems, whereby some rotation-damping systems significantly reduced rotational head acceleration and associated TBI risk.

Reflections on an end-of-life care course for preclinical medical students.

BACKGROUND/PURPOSE: Undergraduate medical education lacks standardized curricula for teaching end-of-life care and only sporadic curricula evaluations have been reported. The objectives of this study were to evaluate the effect of a multimodal teaching program on preclinical medical students' knowledge of palliative care, and their beliefs relating to ethical decision-making. METHODS: This study had a quasi-experimental design. The teaching formats included didactic lectures, bedside patient care, and interactive discussions. A structured questionnaire evaluated the effects of educational intervention---in terms of knowledge of palliative care and beliefs about common ethical dilemmas relating to end-of-life care in Taiwan. RESULTS: All 118 students who participated in the study completed the questionnaire. Students showed significant improvement (score of 9.97 pre-test vs. 12.73 post-test; p < 0.001) in the 18-item palliative care knowledge questionnaire after educational intervention. Among the four common ethical dilemmas, students' beliefs of truth-telling (4.22 vs. 4.54; range 1-5; t = -4.66; p < 0.001) and place of care (4.37 vs. 4.52; range 1-5; t = -2.43; p < 0.05) were significantly improved. Logistic regression showed that the improvement in beliefs about ethical decision-making was not significantly influenced by improved knowledge of palliative care. CONCLUSION: A 1-week multimodal curriculum for preclinical medical students can improve the knowledge and beliefs about ethical decision-making in managing terminally ill patients. Clinical skills of symptom management, especially pain control, and ethical decision-making regarding artificial nutrition and hydration should be emphasized in medical education, to promote students' competence in end-of-life care.

Evaluation of a novel bicycle helmet concept in oblique impact testing.

BACKGROUND: A novel bicycle helmet concept has been developed to mitigate rotational head acceleration, which is a predominant mechanism of traumatic brain injury (TBI). This WAVECEL concept employs a collapsible cellular structure that is recessed within the helmet to provide a rotational suspension. This cellular concept differs from other bicycle helmet technologies for mitigation of rotational head acceleration, such as the commercially available Multi-Directional Impact Protection System (MIPS) technology which employs a slip liner to permit sliding between the helmet and the head during impact. This study quantified the efficacy of both, the WAVECEL cellular concept, and a MIPS helmet, in direct comparison to a traditional bicycle helmet made of rigid expanded polystyrene (EPS). METHODS: Three bicycle helmet types were subjected to oblique impacts in guided vertical drop tests onto an angled anvil: traditional EPS helmets (CONTROL group); helmets with a MIPS slip liner (SLIP group); and helmets with a WAVECEL cellular structure (CELL group). Helmet performance was evaluated using 4.8 m/s impacts onto anvils angled at 30°, 45°, and 60° from the horizontal plane. In addition, helmet performance was tested at a faster speed of 6.2 m/s onto the 45° anvil. Five helmets were tested under each of the four impact conditions for each of the three groups, requiring a total of 60 helmets. Headform kinematics were acquired and used to calculate an injury risk criterion for Abbreviated Injury Score (AIS) 2 brain injury. RESULTS: Linear acceleration of the headform remained below 90 g and was not associated with the risk of skull fracture in any impact scenario and helmet type. Headform rotational acceleration in the CONTROL group was highest for 6.2 m/s impacts onto the 45° anvil (7.2 ± 0.6 krad/s2). In this impact scenario, SLIP helmets and CELL helmets reduced rotational acceleration by 22% (p = 0003) and 73% (p < 0.001), respectively, compared to CONTROL helmets. The CONTROL group had the highest AIS 2 brain injury risk of 59 ± 8% for 6.2 m/s impacts onto the 45° anvil. In this impact scenario, SLIP helmets and CELL helmets reduced the AIS 2 brain injury risk to 34.2% (p = 0.001) and 1.2% (p < 0.001), respectively, compared to CONTROL helmets. DISCUSSION: Results of this study are limited to a narrow range of impact conditions, but demonstrated the potential that rotational acceleration and the associated brain injury risk can be significantly reduced by the cellular WAVECEL concept or a MIPS slip liner. Results obtained under specific impact angles and impact velocities indicated performance differences between these mechanisms. These differences emphasize the need for continued research and development efforts toward helmet technologies that further improve protection from brain injury over a wide range a realistic impact parameters.

Effects of a multimodule curriculum of palliative care on medical students.

BACKGROUND/PURPOSE: The objective of this study was to investigate the effects of educational intervention using a multimodule curriculum of palliative care on medical students, and to explore significant factors that influence improvement in beliefs of ethical decision-making. METHODS: A total of 259 medical students enrolled in the "Family, Society and Medicine" course, and accepted a multimodule palliative care curriculum that included a 1-hour lecture, 1 hour of patient contact, 1 hour of literature reading, and 1 hour of discussion. A questionnaire was administered before and after the course to evaluate improvements in medical students' knowledge (principles and clinical management) of palliative care and their beliefs concerning ethical decision-making in palliative care. RESULTS: The students showed significant improvements after the course in their knowledge of the principles of palliative care (pretest 58.4% vs. posttest 73.1%; p less than 0.01) and clinical management of palliative care (pretest 58.8% vs. posttest 67.9%; p less than 0.01). Although their beliefs about ethical decision-making were also improved after the course, the medical students did not have a positive belief of "artificial nutrition and hydration is not always beneficial for terminal cancer patients", with a mean score of only 3.15 and 3.51 (pretest and posttest, respectively; range, 1-5). The logistic regression model showed that improvement in knowledge of either principles or clinical management did not significantly improve beliefs about ethical decision-making. CONCLUSION: A multimodule curriculum of palliative care for medical students can significantly improve their knowledge on principles of clinical management and beliefs about ethical decision-making in palliative care. As for changes in beliefs about ethical decision-making in palliative care, continued ethical and clinical training is required.

Comparison of 4 Methods for Dynamization of Locking Plates: Differences in the Amount and Type of Fracture Motion.

BACKGROUND: Decreasing the stiffness of locked plating constructs can promote natural fracture healing by controlled dynamization of the fracture. This biomechanical study compared the effect of 4 different stiffness reduction methods on interfragmentary motion by measuring axial motion and shear motion at the fracture site. METHODS: Distal femur locking plates were applied to bridge a metadiaphyseal fracture in femur surrogates. A locked construct with a short-bridge span served as the nondynamized control group (LOCKED). Four different methods for stiffness reduction were evaluated: replacing diaphyseal locking screws with nonlocked screws (NONLOCKED); bridge dynamization (BRIDGE) with 2 empty screw holes proximal to the fracture; screw dynamization with far cortical locking (FCL) screws; and plate dynamization with active locking plates (ACTIVE). Construct stiffness, axial motion, and shear motion at the fracture site were measured to characterize each dynamization methods. RESULTS: Compared with LOCKED control constructs, NONLOCKED constructs had a similar stiffness (P = 0.08), axial motion (P = 0.07), and shear motion (P = 0.97). BRIDGE constructs reduced stiffness by 45% compared with LOCKED constructs (P < 0.001), but interfragmentary motion was dominated by shear. Compared with LOCKED constructs, FCL and ACTIVE constructs reduced stiffness by 62% (P < 0.001) and 75% (P < 0.001), respectively, and significantly increased axial motion, but not shear motion. CONCLUSIONS: In a surrogate model of a distal femur fracture, replacing locked with nonlocked diaphyseal screws does not significantly decrease construct stiffness and does not enhance interfragmentary motion. A longer bridge span primarily increases shear motion, not axial motion. The use of FCL screws or active plating delivers axial dynamization without introducing shear motion.

Dynamic Fixation of Humeral Shaft Fractures Using Active Locking Plates: A Prospective Observational Study.

BACKGROUND: Rigid locked plating constructs can suppress fracture healing by inhibiting interfragmentary motion required to stimulate natural bone healing by callus formation. Dynamic fixation with active locking plates reduces construct stiffness, enables controlled interfragmentary motion, and has been shown to induce faster and stronger bone healing in vivo compared to rigid locking plates. This prospective observational study represents the first clinical use of active locking plates. It documents our early clinical experience with active plates for stabilization of humeral shaft fractures to assess their durability and understand potential complications. METHODS: Eleven consecutive patients with humeral shaft fractures (AO/OTA types 12 A-C) were prospectively enrolled at a level I and a level II trauma center. Fractures were stabilized by using active locking plates without supplemental bone graft or bone morphogenic proteins. The screw holes of active locking plates are elastically suspended in elastomer envelopes inside the plate, enabling up to 1.5 mm of controlled interfragmentary motion. Progression of fracture healing and integrity of implant fixation was assessed radiographically at 3, 6, 12, and 24 weeks post surgery. Patient-reported functional outcome measures were obtained at 6, 12, and 24 weeks post surgery. The primary endpoint of this study was plate durability in absence of plate bending or breakage, or failure of the elastically suspended locking hole mechanism. Secondary endpoints included fracture healing, complications requiring revision surgery, and functional outcome scores. RESULTS: The eleven patients had six simple AO/ OTA type 12A fractures, three wedge type 12B fractures, and two comminuted type 12C fracture, including one open fracture. All active locking plates endured the 6-month loading period without any signs of fatigue or failure. Ten of eleven fractures healed at 10.9 ± 5.2 weeks, as evident by bridging callus and pain-free function. One fracture required revision surgery 37 weeks post surgery due to late fixation failure at the screwbone interface in the presence of a atrophic delayed union. The average Disability of the Arm, Shoulder and Hand (DASH) score improved from 31 ± 22 at week 6 to 13 ± 15 by week 24, approaching that of the normal, healthy population (DASH = 10.1). By week 12, the difference between Constant shoulder scores, expressed as the difference between the affected and contralateral arm (8 ± 8), was considered excellent. By week 24, the SF-12 physical health score (44 ± 9) and mental health score (48 ± 11) approached the mean value of 50 that represents the norm for the general U.S. population. CONCLUSION: Absence of failure of the plate and locking holes suggests that dynamic fixation of humeral shaft fractures with active plates provides safe and effective fixation. Moreover, early callus bridging and excellent functional outcome scores suggest that dynamic fixation with active locking plates may promote increased fracture healing over standard locked plating.

Dynamic Stabilization of Simple Fractures With Active Plates Delivers Stronger Healing Than Conventional Compression Plating.

OBJECTIVES: Active plates dynamize a fracture by elastic suspension of screw holes within the plate. We hypothesized that dynamic stabilization with active plates delivers stronger healing relative to standard compression plating. METHODS: Twelve sheep were randomized to receive either a standard compression plate (CP) or an active plate (ACTIVE) for stabilization of an anatomically reduced tibial osteotomy. In the CP group, absolute stabilization was pursued by interfragmentary compression with 6 cortical screws. In the ACTIVE group, dynamic stabilization after bony apposition was achieved with 6 elastically suspended locking screws. Fracture healing was analyzed weekly on radiographs. After sacrifice 9 weeks postsurgery, the torsional strength of healed tibiae and contralateral tibiae was measured. Finally, computed tomography was used to assess fracture patterns and healing modes. RESULTS: Healing in both groups included periosteal callus formation. ACTIVE specimens had almost 6 times more callus area by week 9 (P < 0.001) than CP specimens. ACTIVE specimens recovered on average 64% of their native strength by week 9, and were over twice as strong as CP specimens, which recovered 24% of their native strength (P = 0.008). Microcomputed tomography demonstrated that compression plating induced a combination of primary bone healing and gap healing. Active plating consistently stimulated biological bone healing by periosteal callus formation. CONCLUSIONS: Compared with compression plating, dynamic stabilization of simple fractures with active plates delivers significantly stronger healing.

Dynamic Stabilization with Active Locking Plates Delivers Faster, Stronger, and More Symmetric Fracture-Healing.

BACKGROUND: Axial dynamization of fractures can promote healing, and overly stiff fixation can suppress healing. A novel technology, termed active plating, provides controlled axial dynamization by the elastic suspension of locking holes within the plate. This prospective, controlled animal study evaluated the effect of active plates on fracture-healing in an established ovine osteotomy model. We hypothesized that symmetric axial dynamization with active plates stimulates circumferential callus and delivers faster and stronger healing relative to standard locking plates. METHODS: Twelve sheep were randomly assigned to receive a standard locking plate or an active locking plate for stabilization of a 3-mm tibial osteotomy gap. The only difference between plates was that locking holes of active plates were elastically suspended, allowing up to 1.5 mm of axial motion at the fracture. Fracture-healing was analyzed weekly on radiographs. After sacrifice at nine weeks postoperatively, callus volume and distribution were assessed by computed tomography. Finally, to determine their strength, healed tibiae and contralateral tibiae were tested in torsion until failure. RESULTS: At each follow-up, the active locking plate group had more callus (p < 0.001) than the standard locking plate group. At postoperative week 6, all active locking plate group specimens had bridging callus at the three visible cortices. In standard locking plate group specimens, only 50% of these cortices had bridged. Computed tomography demonstrated that all active locking plate group specimens and one of the six standard locking plate group specimens had developed circumferential callus. Torsion tests after plate removal demonstrated that active locking plate group specimens recovered 81% of their native strength and were 399% stronger than standard locking plate group specimens (p < 0.001), which had recovered only 17% of their native strength. All active locking plate group specimens failed by spiral fracture outside the callus zone, but standard locking plate group specimens fractured through the osteotomy gap. CONCLUSIONS: Symmetric axial dynamization with active locking plates stimulates circumferential callus and yields faster and stronger healing than standard locking plates. CLINICAL RELEVANCE: The stimulatory effect of controlled motion on fracture-healing by active locking plates has the potential to reduce healing complications and to shorten the time to return to function.

Dynamic locking plates provide symmetric axial dynamization to stimulate fracture healing.

Axial dynamization of an osteosynthesis construct can promote fracture healing. This biomechanical study evaluated a novel dynamic locking plate that derives symmetric axial dynamization by elastic suspension of locking holes within the plate. Standard locked and dynamic plating constructs were tested in a diaphyseal bridge-plating model of the femoral diaphysis to determine the amount and symmetry of interfragmentary motion under axial loading, and to assess construct stiffness under axial loading, torsion, and bending. Subsequently, constructs were loaded until failure to determine construct strength and failure modes. Finally, strength tests were repeated in osteoporotic bone surrogates. One body-weight axial loading of standard locked constructs produced asymmetric interfragmentary motion that was over three times smaller at the near cortex (0.1 ± 0.01 mm) than at the far cortex (0.32 ± 0.02 mm). Compared to standard locked constructs, dynamic plating constructs enhanced motion by 0.32 mm at the near cortex and by 0.33 mm at the far cortex and yielded a 77% lower axial stiffness (p < 0.001). Dynamic plating constructs were at least as strong as standard locked constructs under all test conditions. In conclusion, dynamic locking plates symmetrically enhance interfragmentary motion, deliver controlled axial dynamization, and are at least comparable in strength to standard locked constructs. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 33:1218-1225, 2015.