Radiation Dose Reduction for Computed Tomography Localizer Radiography Using an Ag Additional Filter.

OBJECTIVE: This study aimed to assess the potential of an Ag additional filter attached to the bow tie filter of a computed tomography (CT) scanner to reduce the radiation dose in CT localizer radiography. METHODS: Radiation doses in CT localizer radiography with Cu and Ag additional filters were evaluated based on dose measurements and Monte Carlo simulations. Image quality evaluations of an adult torso phantom were performed, and the automatic exposure control performance was evaluated in terms of the water-equivalent thickness estimated from CT localizer radiographs. RESULTS: With the Ag additional filter, effective doses were approximately 72% to 75% lower than those with the Cu additional filter. The image quality and water-equivalent thickness with the Ag additional filter were similar to those with the Cu additional filter. CONCLUSIONS: The Ag additional filter helped significantly reduce radiation doses in CT localizer radiography while maintaining image quality and performance.

Usability of the lateral decubitus position on four-dimensional ultra-low-dose computed tomography for the detection of localized pleural adhesion in the pulmonary apical region.

BACKGROUND: Localized pleural adhesion (LPA) evaluation in the apical region is difficult even with four-dimensional ultra-low-dose computed tomography (4D-ULDCT) in the supine position due to smaller pleural movements. PURPOSE: To assess usability of 4D-ULDCT in the lateral decubitus (LD) position for LPA detection in the apical region. MATERIAL AND METHODS: Forty-seven patients underwent 4D-ULDCT of a single respiration cycle with 16-cm coverage of body axis in supine and LD positions with the affected lung uppermost. Intraoperative thoracoscopic findings confirmed LPA presence. A pleural point and a corresponding point on costal outer edge were placed in identical axial planes at end-inspiration. Pleuro-chest wall distance between two points (PCD) was calculated at each respiratory phase. In the affected lung, average change in amount of PCD (PCDACA) was compared between patients with and without LPA in total and two sub-groups (non-COPD and COPD, non-emphysematous and emphysematous patients) in supine and non-dependent (ND) LD positions. Receiver operating characteristic (ROC) curve analysis was performed to determine optimal thresholds in PCDACA for differentiating patients with LPA from those without. RESULTS: In COPD/emphysematous patients and total population, PCDACA with LPA was smaller than in those without in the supine and NDLD positions for overall, lateral, and dorsal regions. For the lateral region in COPD patients, area under ROC curve (AUC) increased from supine (0.64) to NDLD position (0.81). For the dorsal region in emphysematous patients, AUC increased from supine (0.76) to NDLD position (0.96). CONCLUSION: 4D-ULDCT in LD position may be useful for LPA detection in apical regions for COPD and/or emphysematous patients.

Influence of field of view size on image quality: ultra-high-resolution CT vs. conventional high-resolution CT.

OBJECTIVES: This study was conducted in order to compare the effect of field of view (FOV) size on image quality between ultra-high-resolution CT (U-HRCT) and conventional high-resolution CT (HRCT). METHODS: Eleven cadaveric lungs were scanned with U-HRCT and conventional HRCT and reconstructed with five FOVs (40, 80, 160, 240, and 320 mm). Three radiologists evaluated and scored the images. Three image evaluations were performed, comparing the image quality with the five FOVs with respect to the 160-mm FOV. The first evaluation was performed on conventional HRCT images, and the second evaluation on U-HRCT images. Images were scored on normal structure, abnormal findings, and overall image quality. The third evaluation was a comparison of the images obtained with conventional HRCT and U-HRCT, with scoring performed on overall image quality. Quantitative evaluation of noise was performed by setting ROIs. RESULTS: In conventional HRCT, image quality was improved when the FOV was reduced to 160 mm. In U-HRCT, image quality, except for noise, improved when the FOV was reduced to 80 mm. In the third evaluation, overall image quality was improved in U-HRCT over conventional HRCT at all FOVs. Noise of U-HRCT increased with respect to conventional HRCT when the FOV was reduced from 160 to 40 mm. However, at 240- and 320-mm FOVs, the noise of U-HRCT and conventional HRCT showed no differences. CONCLUSIONS: In conventional HRCT, image quality did not improve when the FOV was reduced below 160 mm. However, in U-HRCT, image quality improved even when the FOV was reduced to 80 mm. KEY POINTS: • Reducing the size of the field of view to 160 mm improves diagnostic imaging quality in high-resolution CT. • In ultra-high-resolution CT, improvements in image quality can be obtained by reducing the size of the field of view to 80 mm. • Ultra-high-resolution CT produces images of higher quality compared with conventional HRCT irrespective of the size of the field of view.

Peripheral bronchial luminal conspicuity on dynamic-ventilation computed tomography: association with radiation doses and temporal resolution by using an ex vivo porcine lung phantom.

BACKGROUND: It is still unclear which image reconstruction algorithm is appropriate for peripheral bronchial luminal conspicuity (PBLC) on dynamic-ventilation computed tomography (DVCT). PURPOSE: To assess the influence of radiation doses and temporal resolution (TR) on the association between movement velocity (MV) and PBLC on DVCT. MATERIAL AND METHODS: An ex vivo porcine lung phantom with simulated respiratory movement was scanned by 320-row CT at 240 mA and 10 mA. Peak and dip CT density and luminal area adjusted by values at end-inspiration (CTDpeak and CTDdip, luminal area ratio [LAR]) for PBLC and MVs were measured and visual scores (VS) were obtained at 12 measurement points on 13 frame images obtained at half and full reconstructions (TR 340 and 190 ms) during expiration. Size-specific dose estimate (SSDE) was applied to presume radiation dose. VS, CTDpeak, CTDdip, LAR, and their cross-correlation coefficients with MV (CCC) were compared among four methods with combinations of two reconstruction algorithms and two doses. RESULTS: The dose at 10 mA was presumed as 26 mA by SSDE for standard proportion adults. VS, CTDdip, CTDpeak, and LAR with half reconstruction at 10 mA (2.52 ± 0.59, 1.016 ± 0.221, 0.948 ± 0.103, and 0.990 ± 0.527) were similar to those at 240 mA except for VS, and different from those with full reconstruction at both doses (2.24 ± 0.85, 0.830 ± 0.209, 0.986 ± 0.065, and 1.012 ± 0.438 at 240 mA) (P < 0.05). CCC for CTDdip with half reconstruction (-0.024 ± 0.552) at 10 mA was higher compared with full reconstruction (-0.503 ± 0.291) (P < 0.05). CONCLUSION: PBLC with half reconstruction at 10 mA was comparable to that at 240 mA and better than those with full reconstruction on DVCT.

Phantom Study of In-Stent Restenosis at High-Spatial-Resolution CT.

Purpose To examine the diagnostic performance of high-spatial-resolution (HSR) CT with 0.25-mm section thickness for evaluating renal artery in-stent restenosis. Materials and Methods A 0.05-mm wire phantom and vessel phantoms with renal stents with in-stent stenotic sections of varying diameters were scanned with both an HSR CT scanner equipped with 160-section multi-detector rows (0.25-mm section thickness) and a conventional CT scanner. The wire phantom was used to analyze modulation transfer function (MTF). With the vessel phantoms, the error rates were calculated as the absolute difference between the measured diameters and true diameters divided by the true diameters at the narrowing sections. For qualitative evaluation, overall image quality and diagnostic accuracy for evaluating stenosis in three stages were assessed by two radiologists. Statistical analyses included the paired t test, Wilcoxon signed-rank test, and McNemar test. Results HSR CT achieved 24.3 line pairs per centimeter ± 0.5 (standard deviation) and 29.1 line pairs per centimeter ± 0.4 at 10% and 2% MTF, respectively; and conventional CT was 12.5 line pairs per centimeter ± 0.1 and 14.3 line pairs per centimeter ± 0.1 at 10% and 2% MTF, respectively. The mean error rate of the measured diameter at HSR CT (8.0% ± 5.8) was significantly lower than that at at conventional CT (16.9% ± 9.3; P < .001). Image quality at HSR CT was significantly better than that at conventional CT (P < .001), but HSR CT was not significantly superior to conventional CT in terms of diagnostic accuracy. Conclusion Compared with conventional CT, high-spatial-resolution CT achieved spatial resolutions of up to 29 line pairs per centimeter at 2% modulation transfer function and yielded improved measurement accuracy for the evaluation of in-stent restenosis in a phantom study of renal artery stents. Published under a CC BY 4.0 license.

Subjective and objective comparisons of image quality between ultra-high-resolution CT and conventional area detector CT in phantoms and cadaveric human lungs.

OBJECTIVES: To compare the image quality of the lungs between ultra-high-resolution CT (U-HRCT) and conventional area detector CT (AD-CT) images. METHODS: Image data of slit phantoms (0.35, 0.30, and 0.15 mm) and 11 cadaveric human lungs were acquired by both U-HRCT and AD-CT devices. U-HRCT images were obtained with three acquisition modes: normal mode (U-HRCTN: 896 channels, 0.5 mm × 80 rows; 512 matrix), super-high-resolution mode (U-HRCTSHR: 1792 channels, 0.25 mm × 160 rows; 1024 matrix), and volume mode (U-HRCTSHR-VOL: non-helical acquisition with U-HRCTSHR). AD-CT images were obtained with the same conditions as U-HRCTN. Three independent observers scored normal anatomical structures (vessels and bronchi), abnormal CT findings (faint nodules, solid nodules, ground-glass opacity, consolidation, emphysema, interlobular septal thickening, intralobular reticular opacities, bronchovascular bundle thickening, bronchiectasis, and honeycombing), noise, artifacts, and overall image quality on a 3-point scale (1 = worst, 2 = equal, 3 = best) compared with U-HRCTN. Noise values were calculated quantitatively. RESULTS: U-HRCT could depict a 0.15-mm slit. Both U-HRCTSHR and U-HRCTSHR-VOL significantly improved visualization of normal anatomical structures and abnormal CT findings, except for intralobular reticular opacities and reduced artifacts, compared with AD-CT (p < 0.014). Visually, U-HRCTSHR-VOL has less noise than U-HRCTSHR and AD-CT (p < 0.00001). Quantitative noise values were significantly higher in the following order: U-HRCTSHR (mean, 30.41), U-HRCTSHR-VOL (26.84), AD-CT (16.03), and U-HRCTN (15.14) (p < 0.0001). U-HRCTSHR and U-HRCTSHR-VOL resulted in significantly higher overall image quality than AD-CT and were almost equal to U-HRCTN (p < 0.0001). CONCLUSIONS: Both U-HRCTSHR and U-HRCTSHR-VOL can provide higher image quality than AD-CT, while U-HRCTSHR-VOL was less noisy than U-HRCTSHR. KEY POINTS: • Ultra-high-resolution CT (U-HRCT) can improve spatial resolution. • U-HRCT can reduce streak and dark band artifacts. • U-HRCT can provide higher image quality than conventional area detector CT. • In U-HRCT, the volume mode is less noisy than the super-high-resolution mode. • U-HRCT may provide more detailed information about the lung anatomy and pathology.

[Development of Audio Indicator System for Respiratory Dynamic CT Imaging].

We created the device, which can conduct a radiological technologist's voice to a subject during CT scanning. For 149 lung cancer, dynamic respiratory CT were performed. 92 cases were performed using this device, the others were without this device. The respiratory cycle and respiratory amplitude were analyzed from the lung density. A stable respirating cycle was obtained by using the audio indicator system. The audio indicator system is useful for respiratory dynamic CT.

Study of Preoperative 3D-CT Angiography of Uterine Artery in Patients with Uterine Cervical Cancer.

Depiction of the fine vessel can provide useful preoperative information for patients with uterine cervical cancer. Although angiography can visualize vessels in detail, it is invasive. MR-angiography is a minimally invasive method to depict vessels, but the resolution of images is insufficient for preoperative evaluation. In this study, we used less invasive three-dimensional CT angiography (3D-CTA) and reconstructed images of adaptive iterative dose resolution 3D (AIDR 3D) with display field of view (D-FOV), which are suitable for arteries with large and small diameters, and created the fusion images. Created images allowed the observation of vessel branch in wide area compared with angiography, and it was less invasive. We evaluated the utility of 3D-CTA for visualizing fine vessels branching from uterine artery as preoperative evaluation for radial hysterectomy. 3D-CTA was obtained in nine patients. Conventional reconstruction and magnification reconstruction (D-FOV: 320‒360 mm, 150 mm) was made using arterial phase. Normal volume rendering image (N-VR) was made from conventional reconstruction image, and hybrid volume rendering image (H-VR) was made from conventional and magnification reconstruction image. Visual evaluation of each VR image was performed by 5 trained radiologists. A Wilcoxon rank sum test was performed for each result. No statistical significance was found in the visualization of vessels with large diameter (p=0.81), but statistical significance was detected in the visualization of the uterine artery and its ascending/descending branches (p<0.05). H-VR could visualize fine vessels clearer than N-VR, and H-VR could depict a vascular map including fine vessels in a large field. Therefore, H-VR could provide useful information for surgical operation. Additional depiction of vein and ureter could clearly visualize the anatomical relationship of each structure, and new clinical finding of anatomical relationship between uterine artery and ureter was suggested. This new clinical finding was useful in radical hysterectomy in which crossing site of the uterine artery and ureter is dissected. This method is simple to create and useful for various clinical surgery.

Correlation analysis of organ doses determined by Monte Carlo simulation with dose metrics for patients undergoing chest-abdomen-pelvis CT examinations.

OBJECTIVES: This study aimed to determine organ doses based on Monte Carlo (MC) simulations for individual patients undergoing routine adult chest abdomen-pelvis computed tomography (CT) examinations and to evaluate the correlations of organ doses with patient size and dose metrics. METHODS: MC simulations were performed by reading detailed descriptions of the CT scanner, scanning parameters, and CT images of phantoms and patients into the simulation software. The simulation models were validated by comparing the simulated doses with the doses measured by in-phantom dosimetry using radiophotoluminescent glass dosimeters and an adult anthropomorphic phantom, and organ doses for 80 patients were determined from the simulation results. To obtain patient size and dose metrics, body mass index and volume computed tomography dose index (CTDIvol) data were collected. Water equivalent diameter (WED) was calculated from the CT images of each patient. Size-specific dose estimates (SSDE) were calculated using CTDIvol and average WED over the scan range, and organ specific SSDE were calculated using the average CTDIvol and WED over each organ position. The correlations of organ doses with dose metrics were evaluated using coefficients of determination. RESULTS: Organ doses increased with patient size, and the doses for obese were approximately two to three times higher than those for underweight patients. Organ doses exhibited stronger linear relationships with organ specific SSDE (R2 ≥ 0.82) than other dose metrics. CONCLUSIONS: The linear regression fits between organ doses determined by MC simulation and organ-specific SSDE are valuable for simplified and accurate organ dose estimation for individual patients undergoing CT examinations.

Preoperative assessment of localized pleural adhesion: Utility of software-assisted analysis on dynamic-ventilation computed tomography.

PURPOSE: To assess the usefulness of software analysis using dynamic-ventilation CT for localized pleural adhesion (LPA). MATERIALS AND METHODS: Fifty-one patients scheduled to undergo surgery underwent both dynamic-ventilation CT and static chest CT as preoperative assessments. Five observers independently evaluated the presence and severity of LPA on a three-point scale (non, mild, and severe LPA) for 9 pleural regions (upper, middle, and lower pleural aspects on ventral, lateral, and dorsal areas) on the chest CT by three different methods by observing images from: static high-resolution CT (static image); dynamic-ventilation CT (movie image), and dynamic-ventilation CT while referring to the adhesion map (movie image with color map), which was created using research software to visualize movement differences between the lung surface and chest wall. The presence and severity of LPA was confirmed by intraoperative thoracoscopic findings. Parameters of diagnostic accuracy for LPA presence and severity were assessed among the three methods using Wilcoxon signed rank test in total and for each of the three pleural aspects. RESULTS: Mild and severe LPA were confirmed in 14 and 8 patients. Movie image with color map had higher sensitivity (56.9 ±â€¯10.7 %) and negative predictive value (NPV) (91.4 ±â€¯1.7 %) in LPA detection than both movie image and static image. Additionally, for severe LPA, detection sensitivity was the highest with movie image with color map (82.5 ±â€¯6.1 %), followed by movie image (58.8 ±â€¯17.0 %) and static image (38.8 ±â€¯13.9 %). For LPA severity, movie image with color map was similar to movie image and superior to static image in accuracy as well as underestimation and overestimation, with a mean value of 80.2 %. CONCLUSION: Software-assisted dynamic-ventilation CT may be a useful novel imaging approach to improve the detection performance of LPA.

Ultra high-resolution computed tomography with 1024-matrix: Comparison with 512-matrix for the evaluation of pulmonary nodules.

PURPOSE: To determine whether a 1024-matrix provides superior image quality for the evaluation of pulmonary nodules. MATERIALS AND METHODS: Prospective evaluation conducted between December 2017 and April 2018, during which CT images showing lung nodules of more than 6 mm and less than 30 mmm were reconstructed with 2 different protocols: 0.5-mm thickness, 512 × 512 matrix, 34.5-cm field of view (FOV) (0.5-512 protocol); and 2-mm thickness, 1024 × 1024 matrix, 34.5-cm FOV (2-1024 protocol). Lung nodule characteristics such as margin, lobulation, pleural indentation, spiculation as well as peripheral vessels and bronchioles visibility and overall image quality were evaluated by three chest radiologists, using a 5-point scale. Image noise was evaluated by measuring the standard deviation in the region of interest for each image. RESULTS: A total of 89 nodules were evaluated. The 2-1024 protocol performed significantly better for the subjective evaluation of pulmonary nodules (p = 0.006 ∼ p < 0.0001). However, image noise was significantly higher both subjectively and objectively (p = 0.036, p < 0.0001). CONCLUSION: The use of a 2-1024 protocol does not increase the amount of images and allows better assessment of pulmonary nodules, despite noise increase.

Three-dimensional perfusion imaging of hepatocellular carcinoma using 256-slice multidetector-row computed tomography.

PURPOSE: The aim of this study was to evaluate the clinical capability of three-dimensional (3D) perfusion imaging of hepatocellular carcinoma (HCC) by performing dynamic scanning using a 256-slice multidetector-row CT (MDCT) scanner. MATERIALS AND METHODS: Two patients with HCC were examined in this study. They were scheduled to undergo transcatheter arterial infusion therapy using an arterial infusion reservoir system. The CT system used was a newly developed prototype scanner of 256-slice MDCT. Dynamic CT scanning was performed with intraarterial injection via the reservoir route, and perfusion analysis was done based on the 3D data. RESULTS: The blood flow volume per unit volume in the tumors was significantly increased compared with that in normal hepatic parenchyma. Using a 3D workstation, 3D perfusion images could be displayed by fusing CT images with perfusion images about blood flow volume. CONCLUSION: Three-dimensional perfusion images, which enable 3D evaluation of perfusion in HCCs, can be generated using 256-slice MDCT.

Effect of Matrix Size on the Image Quality of Ultra-high-resolution CT of the Lung: Comparison of 512 × 512, 1024 × 1024, and 2048 × 2048.

RATIONALE AND OBJECTIVES: This study aimed to assess the effect of matrix size on the spatial resolution and image quality of ultra-high-resolution computed tomography (U-HRCT). MATERIALS AND METHODS: Slit phantoms and 11 cadaveric lungs were scanned on U-HRCT. Slit phantom scans were reconstructed using a 20-mm field of view (FOV) with 1024 matrix size and a 320-mm FOV with 512, 1024, and 2048 matrix sizes. Cadaveric lung scans were reconstructed using 512, 1024, and 2048 matrix sizes. Three observers subjectively scored the images on a three-point scale (1 = worst, 3 = best), in terms of overall image quality, noise, streak artifact, vessel, bronchi, and image findings. The median score of the three observers was evaluated by Wilcoxon signed-rank test with Bonferroni correction. Noise was measured quantitatively and evaluated with the Tukey test. A P value of <.05 was considered significant. RESULTS: The maximum spatial resolution was 0.14 mm; among the 320-mm FOV images, the 2048 matrix had the highest resolution and was significantly better than the 1024 matrix in terms of overall quality, solid nodule, ground-glass opacity, emphysema, intralobular reticulation, honeycombing, and clarity of vessels (P < .05). Both the 2048 and 1024 matrices performed significantly better than the 512 matrix (P < .001), except for noise and streak artifact. The visual and quantitative noise decreased significantly in the order of 512, 1024, and 2048 (P < .001). CONCLUSION: In U-HRCT scans, a large matrix size maintained the spatial resolution and improved the image quality and assessment of lung diseases, despite an increase in image noise, when compared to a 512 matrix size.

Influence of gantry rotation time and scan mode on image quality in ultra-high-resolution CT system.

OBJECTIVES: To investigate the image quality of helical scan (HS) mode and non-helical scan (non-HS) mode on ultra-high-resolution CT in different gantry rotation time. METHODS: non-HS with 0.35 s/rot (non-HS200 mA/0.35 s). Three observers compared each non-HS image with HS image, and scored non-HS images by using 3-point scale, paying attention to normal findings, abnormal findings, noise, streak artifact, and overall image quality. Statistical analysis was performed with Steel-Dwass test. RESULTS: Overall image quality (score: 2.45) and noise (score: 2.42) of non-HS 200 mA/1.5s was statistically best (p < 0.0005). Overall Image quality and noise of non-HS200 mA/0.75 s (score: 2.0) was comparable to that of HS200 mA/1.5 s. CTDIvol of HS200 mA/1.5 s is 23.2 mGy. CTDIvol of non-HS200 mA/1.5 s, non-HS200 mA/0.75 s, non-HS200 mA/0.35 s is 19.2 mGy, 9.8 mGy, 4.7 mGy. CONCLUSION: Overall image quality and noise of non-helical scan is better than that of helical scan in the same rotation time. Overall Image quality of non-HS200 mA/0.75 s is comparable to that of HS200 mA/1.5 s, though the radiation dose of non-HS200 mA/0.75 s is lower than that of HS200 mA/1.5 s.

Continuous quantitative measurement of the main bronchial dimensions and lung density in the lateral position by four-dimensional dynamic-ventilation CT in smokers and COPD patients.

PURPOSE: The purpose of this study was to measure changes in lung density and airway dimension in smokers in the lateral position using four-dimensional dynamic-ventilation computed tomography (CT) during free breathing and to evaluate their correlations with spirometric values. MATERIALS AND METHODS: Preoperative pleural adhesion assessments included dynamic-ventilation CT of 42 smokers (including 22 patients with COPD) in the lateral position, with the unoperated lung beneath (dependent lung). The scanned lungs' mean lung density (MLD) and the bilateral main bronchi's luminal areas (Ai) were measured automatically (13-18 continuous image frames, 0.35 seconds/frame). Calculations included cross-correlation coefficients (CCCs) between the MLD and Ai time curves, and correlations between the quantitative measurements and spirometric values were evaluated by using Spearman's rank coefficient. RESULTS: The ΔMLD1.05 (from the peak inspiration frame to the third expiratory frame, 1.05 seconds later) in the nondependent lung negatively correlated with FEV1/FVC (r=-0.417, P<0.01), suggesting that large expiratory movement of the nondependent lung would compensate limited expiratory movement of the dependent lung due to COPD. The ΔAi1.05 negatively correlated with the FEV1/FVC predicted in both the lungs (r=-0.465 and -0.311, P<0.05), suggesting that early expiratory collapses of the main bronchi indicate severe airflow limitation. The CCC correlated with FEV1/FVC in the dependent lung (r=-0.474, P<0.01), suggesting that reduced synchrony between the proximal airway and lung occurs in patients with severe airflow limitation. CONCLUSION: In COPD patients, in the lateral position, the following abnormal dynamic-ventilation CT findings are associated with airflow limitation: enhanced complementary ventilation in the nondependent lung, early expiratory airway collapses, and reduced synchrony between airway and lung movements in the dependent lung.

Association of Focal Radiation Dose Adjusted on Cross Sections with Subsolid Nodule Visibility and Quantification on Computed Tomography Images Using AIDR 3D: Comparison Among Scanning at 84, 42, and 7 mAs.

RATIONALE AND OBJECTIVES: The objectives of this study were to compare the visibility and quantification of subsolid nodules (SSNs) on computed tomography (CT) using adaptive iterative dose reduction using three-dimensional processing between 7 and 42 mAs and to assess the association of size-specific dose estimate (SSDE) with relative measured value change between 7 and 84 mAs (RMVC7-84) and relative measured value change between 42 and 84 mAs (RMVC42-84). MATERIALS AND METHODS: As a Japanese multicenter research project (Area-detector Computed Tomography for the Investigation of Thoracic Diseases [ACTIve] study), 50 subjects underwent chest CT with 120 kV, 0.35 second per location and three tube currents: 240 mA (84 mAs), 120 mA (42 mAs), and 20 mA (7 mAs). Axial CT images were reconstructed using adaptive iterative dose reduction using three-dimensional processing. SSN visibility was assessed with three grades (1, obscure, to 3, definitely visible) using CT at 84 mAs as reference standard and compared between 7 and 42 mAs using t test. Dimension, mean CT density, and particular SSDE to the nodular center of 71 SSNs and volume of 58 SSNs (diameter >5 mm) were measured. Measured values (MVs) were compared using Wilcoxon signed-rank tests among CTs at three doses. Pearson correlation analyses were performed to assess the association of SSDE with RMVC7-84: 100 × (MV at 7 mAs - MV at 84 mAs)/MV at 84 mAs and RMVC42-84. RESULTS: SSN visibilities were similar between 7 and 42 mAs (2.76 ± 0.45 vs 2.78 ± 0.40) (P = .67). For larger SSNs (>8 mm), MVs were similar among CTs at three doses (P > .05). For smaller SSNs (<8 mm), dimensions and volumes on CT at 7 mAs were larger and the mean CT density was smaller than 42 and 84 mAs, and SSDE had mild negative correlations with RMVC7-84 (P < .05). CONCLUSIONS: Comparable quantification was demonstrated irrespective of doses for larger SSNs. For smaller SSNs, nodular exaggerating effect associated with decreased SSDE on CT at 7 mAs compared to 84 mAs could result in comparable visibilities to CT at 42 mAs.

Preoperative assessment of pleural adhesion by Four-Dimensional Ultra-Low-Dose Computed Tomography (4D-ULDCT) with Adaptive Iterative Dose Reduction using Three-Dimensional processing (AIDR-3D).

PURPOSE: To assess the feasibility of Four-Dimensional Ultra-Low-Dose Computed Tomography (4D-ULDCT) for distinguishing pleural aspects with localized pleural adhesion (LPA) from those without. METHODS: Twenty-seven patients underwent 4D-ULDCT during a single respiration with a 16cm-coverage of the body axis. The presence and severity of LPA was confirmed by their intraoperative thoracoscopic findings. A point on the pleura and a corresponding point on the outer edge of the costal bone were placed in identical axial planes at end-inspiration. The distance of the two points (PCD), traced by automatic tracking functions respectively, was calculated at each respiratory phase. The maximal and average change amounts in PCD (PCDMCA and PCDACA) were compared among 110 measurement points (MPs) without LPA, 16MPs with mild LPA and 10MPs with severe LPA in upper lung field cranial to the bronchial bifurcation (ULF), and 150MPs without LPA, 17MPs with mild LPA and 9MPs with severe LPA in lower lung field caudal to the bronchial bifurcation (LLF) using the Mann-Whitney U test. RESULTS: In the LLF, PCDACA as well as PCDMCA demonstrated a significant difference among non-LPA, mild LPA and severe LPA (18.1±9.2, 12.3±6.2 and 5.0±3.3mm) (p<0.05). Also in the ULF, PCDACA showed a significant difference among three conditions (9.2±5.5, 5.7±2.8 and 2.2±0.4mm, respectively) (p<0.05), whereas PCDMCA for mild LPA was similar to that for non-LPA (12.3±5.9 and 17.5±11.0mm). CONCLUSIONS: Four D-ULDCT could be a useful non-invasive preoperative assessment modality for the detection of the presence or severity of LPA.

Improvement of spatial resolution in the longitudinal direction for isotropic imaging in helical CT.

Experiments were conducted to confirm the isotropic spatial resolution of multislice CT with a 0.5 mm slice thickness. Isotropic spatial resolution means that the spatial resolution in the transaxial plane (X-Y plane) and that in the longitudinal direction (Z direction) are equivalent. To obtain point spread function (PSF) values in the X-Y-Z directions, three-dimensional voxel data were obtained by helical scanning of a bead phantom. The modulation transfer function (MTF) values were then obtained by three-dimensional Fourier transform of the PSF. Evaluation of the spatial resolution in the X-Y-Z directions by the MTF values showed that the spatial resolution in the Z direction does not depend on the reconstruction kernel used. It was also found that the spatial resolution in the Z direction, as compared with that in the X-Y plane, is superior with the standard kernel for the abdomen and is inferior with the high-definition kernel for the ears/bones. By performing sharpening filter processing in the Z direction with a high-definition kernel, comparable spatial resolution could be obtained in the X-Y-Z directions. It was confirmed that adjusting the spatial resolution in the Z direction with the reconstruction kernel used is an effective method for isotropic imaging.

New method of evaluating edge-preserving adaptive filters for computed tomography (CT): digital phantom method.

To evaluate the characteristics of edge-preserving adaptive filters for selectively eliminating noise without affecting resolution in low-dose scanning, we have developed a digital phantom image and evaluated noise statistical values, noise characteristics, and resolution characteristics. The results confirmed that edge-preserving adaptive filters function as smoothing filters in low-contrast regions containing noise, permitting the density resolution to be improved, while the strength of the smoothing filter is reduced to maintain spatial resolution in high-contrast regions containing small structures. It has therefore been confirmed that edge-preserving adaptive filters function as filters for selectively eliminating only the noise elements that are increased when the exposure dose is reduced and that such filters are effective for improving image quality. Using such digital phantom images, images acquired using conditions that are difficult to set in actual CT scanning can be obtained and images specifically for the evaluation target can easily be generated. In addition, the noise level, frequency distribution of the noise, and resolution characteristics of the objects present in the input image can be freely set. It is concluded that evaluation of processing using a digital phantom image is effective for evaluating image processing.

Simulator-assisted setting of scan protocols for X-ray CT: development and clinical usefulness of the Scan Plan Simulator.

To assist in the selection of complicated computed tomography (CT) scan protocols and to obtain stable image SD values, prototype "Scan Plan Simulator" software with the following functions was developed and evaluated. 1) The image SD value that will be obtained in actual scanning is estimated by entering the patient's body size and scan protocol, after which a simulated image is displayed so that the estimated image SD value can be checked. The exposure dose can also be estimated in the Scan Plan Simulator. 2) The appropriate tube current is automatically set by entering the required image SD value. We evaluated the accuracy of the Scan Plan Simulator by comparing the simulation results with the image SD values and exposure dose obtained in actual scanning and assessed the usefulness of this method using Monte Carlo simulation based on body thickness data obtained in clinical examinations. The results showed that the Scan Plan Simulator not only stabilizes image SD by minimizing the effects of body size but also permits the exposure dose to be reduced by optimizing tube current.