RESUMO
Stoichiometric thin films of Cu2ZnSnS4 (CZTS) were deposited by the spray technique on a FTO coated glass substrate, with post-annealing in a H2S environment to improve the film properties. CZTS films were used as a counter electrode (CE) in Dye-Sensitized Solar Cells (DSCs) with N719 dye and an iodine electrolyte. The DSC of 0.25 cm(2) area using a CE of CZTS film annealed in a H2S environment under AM 1.5G illumination (100 mW cm(-2)) exhibited a short circuit current density (JSC) = 18.63 mA cm(-2), an open circuit voltage (VOC) = 0.65 V and a fill factor (FF) = 0.53, resulting in an overall power conversion efficiency (PCE) = 6.4%. While the DSC using as deposited CZTS film as a CE showed the PCE = 3.7% with JSC = 13.38 mA cm(-2), VOC = 0.57 V and FF = 0.48. Thus, the spray deposited CZTS films can play an important role as a CE in the large area DSC fabrication.
RESUMO
The deposition of tin sulfide (SnS) nanostructured films using a continuous spray pyrolysis technique is reported with an electric field present at the nozzle for influencing the atomization and the subsequent film deposition. In the absence of the electric field, the X-ray diffraction pattern shows the orthorhombic phase of SnS with a crystallographic preferred orientation along the (040) plane. The application of the electric field results in significant improvement in the morphology and a reduction in surface roughness (28 nm from 37 nm). The direct optical band gap of the films deposited with and without the electric field is estimated to be 1.5 and 1.7 eV, respectively. The photothermal deflection spectroscopy studies show a lower energetic disorder (no Urbach tail), which indicates an annealing effect in the SnS films deposited under the electric field. The improvement in the film properties is reflected in the expected improvement in the power conversion efficiency (PCE) of dye-sensitized solar cells fabricated using the SnS film as a counter electrode. An enhancement of PCE from 2.07% for the film deposited without the electric field to 2.89% for the film deposited with the electric field shows the role of the electric field in the fabrication of improved SnS films.
RESUMO
The world is witnessing tumultuous times as major economic powers including the US, UK, Russia, India, and most of Europe continue to be in a state of lockdown. The worst-hit sectors due to this lockdown are sales, production (manufacturing), transport (aerospace and automotive) and tourism. Lockdowns became necessary as a preventive measure to avoid the spread of the contagious and infectious "Coronavirus Disease 2019" (COVID-19). This newly identified disease is caused by a new strain of the virus being referred to as Severe Acute Respiratory Syndrome CoronaVirus 2 (SARS CoV-2; formerly called 2019-nCoV). We review the current medical and manufacturing response to COVID-19, including advances in instrumentation, sensing, use of lasers, fumigation chambers and development of novel tools such as lab-on-the-chip using combinatorial additive and subtractive manufacturing techniques and use of molecular modelling and molecular docking in drug and vaccine discovery. We also offer perspectives on future considerations on climate change, outsourced versus indigenous manufacturing, automation, and antimicrobial resistance. Overall, this paper attempts to identify key areas where manufacturing can be employed to address societal challenges such as COVID-19.
RESUMO
Transient absorption spectroscopy is employed to study electron transfer dynamics in dye sensitised solar cells employing a series of polymer electrolytes, and correlated with device current-voltage characteristics.
RESUMO
We report here flexible solid-state solar cells based upon dye-sensitised nanocrystalline Al2O3 coated TiO2 films and an I2/NaI doped solid-state polymer electrolyte. Such devices show remarkably high solar-light to electrical energy conversion efficiencies of approximately 5.3% under 10 mW cm-2 AM1.5 illumination.